question about uboot mt7620 RAM_VERSION
Kang-sen Lu
klu at waav.com
Fri Oct 28 16:35:41 CEST 2022
Hi, Stefan:
Thanks for your effort to build a ubbot.bin (RAM_VERSION) for mt7620
router. I tried it out, using tftp to download it. It did start but having
some errors. I have saved the log for you. It is in the attachment.
I want to report to you that I have built the uboot.bin (ROM_VERSION) for
mt7620, based on the git from https://github.com/tessel/uboot-mt7620. Yes,
you told me that code was very old. But I can burn that ROM_VERSION into
mt7620 and see it perform kernel boot correctly. My RAM_VERSION also runs
correctly.
I am wondering if you can point me to the latest uboot git tree for mt7620?
I would be interested in trying it out. The reason I need the source code
of uboot is so that I can enhance it for our own requirement.
Thanks.
Kang-sen
On Wed, Oct 26, 2022 at 1:36 AM Stefan Roese <sr at denx.de> wrote:
> Hi Kang-sen,
>
> On 25.10.22 21:40, Kang-sen Lu wrote:
> > I am sorry that I was working on an old uboot version. You mentioned
> > that you have ported uboot to my7620. I would like to download it. Is it
> > available at this site? https://github.com/u-boot/u-boot
> > <https://github.com/u-boot/u-boot>.
>
> Unfortunately it's not that easy. As your specific board (router) needs
> to get ported to upstream U-Boot. It might be the case, that at least
> the RAM version of the currently supported MT7620 board "mt7620_rfb"
> works for you. But this is very unlikely - sorry, I don't know this
> board and your router in detail.
>
> I've compiled the binaries for the mt7620_rfb and attached the resulting
> u-boot.bin, which might work as a RAM target for you. Just give it a
> try. The TEXT_BASE is 0x80200000, so you should load and boot it from
> there:
>
> => tftp 0x80200000 u-boot.bin
> => go 0x80200000
>
> Let me know if this produces some output or crashes directly.
>
> Thanks,
> Stefan
>
> > Thanks.
> >
> > Kang-sen
> >
> > On Tue, Oct 25, 2022 at 10:47 AM Stefan Roese <sr at denx.de
> > <mailto:sr at denx.de>> wrote:
> >
> > Hi Kang-sen,
> >
> > On 25.10.22 15:25, Kang-sen Lu wrote:
> > > Thanks for your reply.
> > >
> > > I cloned the uboot source code from here:
> > > https://github.com/tessel/uboot-mt7620
> > <https://github.com/tessel/uboot-mt7620>
> > > <https://github.com/tessel/uboot-mt7620
> > <https://github.com/tessel/uboot-mt7620>>
> > >
> > > I built the uboot.bin for RAM_VERSION. If I select option 8 at
> > power up
> > > with the uboot from zbtlink, the new uboot.bin will hang. But if I
> > > caused saveenv() to happen, by changing tftp filename
> > artificially, the
> > > uboot.bin for RAM_VERSION will start and run properly, by the
> > uboot from
> > > zbtlink.
> >
> > Sorry, this is the ancient U-Boot version. I thought you were talking
> > about the mainline U-Boot version, which I ported for MT7620/80 some
> > years ago (with many extensions and fixes by Weijie later on).
> >
> > I don't remember the details of this ancient MT7620 U-Boot version
> > and frankly don't want to dig into this (again).
> >
> > > Maybe Weijie can comment on the experimental result?
> >
> > Maybe.
> >
> > > Thanks.
> > >
> > > Kang-sen
> > >
> > > BTW: How does uboot developer usually run the RAM_VERSION
> > uboot.bin, I
> > > am curious. Is it loaded with tftp server, or something else?
> >
> > Yes. This is very handy and frequently done. Load the RAM version
> > into RAM to the TEXT_BASE address and start it from there via the
> > "go" command.
> >
> > BTW: Please keep the ML on Cc. It might be that someone else has
> > some answers. Or that this topic is interesting for other
> > people as well.
> >
> > Thanks,
> > Stefan
> >
> > > On Tue, Oct 25, 2022 at 12:46 AM Stefan Roese <sr at denx.de
> > <mailto:sr at denx.de>
> > > <mailto:sr at denx.de <mailto:sr at denx.de>>> wrote:
> > >
> > > Hi Kang-sen,
> > >
> > > On 24.10.22 19:58, Kang-sen Lu wrote:
> > > > I am wondering if you have read my reply on 10/18. It is
> very
> > > strange to
> > > > find that unless I had uboot to do a saveenv, the
> RAM_VERSION
> > > uboot.bin
> > > > would not run properly in DRAM.
> > >
> > > Frankly, I don't really understand this message. It's not
> > clear to
> > > me, what you are doing and what is working and what is
> failing.
> > >
> > > I thought you were trying to boot the current mainline U-Boot
> RAM
> > > version u-boot.bin. If yes, which build target did you use?
> What
> > > does it show on the serial console?
> > >
> > > Thanks,
> > > Stefan
> > >
> > > > Thanks.
> > > >
> > > > Kang-sen
> > > >
> > > > On Tue, Oct 18, 2022 at 10:05 AM Kang-sen Lu <klu at waav.com
> > <mailto:klu at waav.com>
> > > <mailto:klu at waav.com <mailto:klu at waav.com>>
> > > > <mailto:klu at waav.com <mailto:klu at waav.com>
> > <mailto:klu at waav.com <mailto:klu at waav.com>>>> wrote:
> > > >
> > > > Hi, Stefan:
> > > >
> > > > Thanks for your reply.
> > > >
> > > > The uboot in the zbtlink mt7620 router has the
> signatures
> > > follows:
> > > >
> > > > U-Boot 1.1.3 (Nov 9 2016 - 15:34:50)
> > > >
> > > > SoC:MediaTek MT7620
> > > > DRAM: Memory Testing..131072K OK. is 128 MB
> > > > relocate_code Pointer at: 87fb0000
> > > > enable ephy clock...done. rf reg 29 = 5
> > > > SSC disabled.
> > > > spi_wait_nsec: 29
> > > > spi device id: ef 40 18 0 0 (40180000)
> > > > Flash: W25Q128BV
> > > >
> > > > I would like to share my strange experience about RAM
> > version
> > > uboot
> > > > for mt7620. By pure luck, I found that when I tried to
> > load a
> > > newly
> > > > built uboot with startup menu option 8, unless I
> > change the
> > > > filename, say, from uboot.bin to uboot1.bin, the newly
> > loaded
> > > uboot
> > > > would not startup properly in RAM.
> > > >
> > > > I don't have the knowledge to find out why this
> variable
> > > "modifies"
> > > > to be none-zero is so important to the execution of
> > uboot in RAM.
> > > > Maybe some expert in this group can easily figure that
> > out.
> > > >
> > > > Thanks.
> > > >
> > > > Kang-sen
> > > >
> > > > On Tue, Oct 18, 2022 at 7:53 AM Stefan Roese
> > <sr at denx.de <mailto:sr at denx.de>
> > > <mailto:sr at denx.de <mailto:sr at denx.de>>
> > > > <mailto:sr at denx.de <mailto:sr at denx.de>
> > <mailto:sr at denx.de <mailto:sr at denx.de>>>> wrote:
> > > >
> > > > Hi Kang-sen,
> > > >
> > > > (added Weijie Gao to Cc)
> > > >
> > > > On 17.10.22 14:11, Kang-sen Lu wrote:
> > > > > I am building uboot.bin for mt7620 router.
> > > > >
> > > > > I used start menu option 8, a hidden one
> > choice, to load
> > > > uboot.bin through
> > > > > tftp.
> > > > >
> > > > > The tftp transfer is OK. But when the new uboot
> > > starts, it hang.
> > > >
> > > > So which mainline U-Boot build target did you use?
> > Don't
> > > you see
> > > > any output on the serial console at all?
> > > >
> > > > > I am wondering if the RAM_VERSION for mt7620
> > still works.
> > > >
> > > > In mainline U-Boot this is usually handled this
> > way. The
> > > SPL U-Boot
> > > > version is responsible for the low-level HW init,
> like
> > > DRAM/DDR init
> > > > etc. It's hard to impossible to chainload this SPL
> > part
> > > from a
> > > > running U-Boot version.
> > > >
> > > > The "RAM_VERSION" is usually the main U-Boot
> > proper image
> > > > "u-boot.bin".
> > > > So in general you are using the correct file here.
> > Even
> > > though I
> > > > have
> > > > not idea, if the build target is correct for your
> > "mt7620
> > > router".
> > > >
> > > > Thanks,
> > > > Stefan
> > > >
> > >
> > > Viele Grüße,
> > > Stefan Roese
> > >
> > > --
> > > DENX Software Engineering GmbH, Managing Director:
> > Wolfgang Denk
> > > HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell,
> > Germany
> > > Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email:
> > > sr at denx.de <mailto:sr at denx.de> <mailto:sr at denx.de
> > <mailto:sr at denx.de>>
> > >
> >
> > Viele Grüße,
> > Stefan Roese
> >
> > --
> > DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> > HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> > Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email:
> > sr at denx.de <mailto:sr at denx.de>
> >
>
> Viele Grüße,
> Stefan Roese
>
> --
> DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
> HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
> Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de
-------------- next part --------------
A non-text attachment was scrubbed...
Name: uboot.bin.ram.stefan.rtf
Type: application/rtf
Size: 3146 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20221028/4784881e/attachment.rtf>
More information about the U-Boot
mailing list