[PATCH 4/4] ARM: dts: imx8m: imx8mm-mx8menlo: Enable SPL SDP support

[Marek Vasut]

Enable DM USB, DM PHY and USB gadget support in imx8mm-mx8menlo SPL
to let the board continue SDP loading of second stage after the first
stage was loaded by BootROM SDP implementation. It is not possible to
jump back into BootROM v1 and let the BootROM implementation continue
the SDP loading, all this has to be performed by the U-Boot CI HDRC
controller driver and SDP protocol implementation, both of which fit
into the SPL just barely.

With this patch, it is possible to start both U-Boot SPL and U-Boot
using e.g. uuu on this board as follows:

$ uuu -brun spl flash.bin

Signed-off-by: Marek Vasut <marex at denx.de>
---
Cc: Fabio Estevam <festevam at denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler at toradex.com>
Cc: Max Krummenacher <max.krummenacher at toradex.com>
Cc: Peng Fan <peng.fan at nxp.com>
Cc: Stefano Babic <sbabic at denx.de>
---
 arch/arm/dts/imx8mm-mx8menlo-u-boot.dtsi | 20 ++++++++++++++++++++
 configs/imx8mm-mx8menlo_defconfig        | 17 ++++++++++++++++-
 2 files changed, 36 insertions(+), 1 deletion(-)

diff --git a/arch/arm/dts/imx8mm-mx8menlo-u-boot.dtsi b/arch/arm/dts/imx8mm-mx8menlo-u-boot.dtsi
index 484d493e33c..7f5f8c384e8 100644
--- a/arch/arm/dts/imx8mm-mx8menlo-u-boot.dtsi
+++ b/arch/arm/dts/imx8mm-mx8menlo-u-boot.dtsi
@@ -17,6 +17,26 @@
 	};
 };
 
+&aips4 {
+	u-boot,dm-spl;
+};
+
 &i2c4 {
 	/delete-node/ codec at 1a;
 };
+
+&reg_usb_otg1_vbus {
+	u-boot,dm-spl;
+};
+
+&usbmisc1 {
+	u-boot,dm-spl;
+};
+
+&usbphynop1 {
+	u-boot,dm-spl;
+};
+
+&usbotg1 {
+	u-boot,dm-spl;
+};
diff --git a/configs/imx8mm-mx8menlo_defconfig b/configs/imx8mm-mx8menlo_defconfig
index 929ff382f27..ad6885942d3 100644
--- a/configs/imx8mm-mx8menlo_defconfig
+++ b/configs/imx8mm-mx8menlo_defconfig
@@ -50,6 +50,9 @@ CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300
 CONFIG_SPL_I2C=y
 CONFIG_SPL_POWER=y
+CONFIG_SPL_USB_HOST=y
+CONFIG_SPL_USB_GADGET=y
+CONFIG_SPL_USB_SDP_SUPPORT=y
 CONFIG_SPL_WATCHDOG=y
 CONFIG_SYS_MAXARGS=64
 CONFIG_SYS_CBSIZE=2048
@@ -65,6 +68,8 @@ CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_USB=y
+CONFIG_CMD_USB_SDP=y
+CONFIG_CMD_USB_MASS_STORAGE=y
 CONFIG_CMD_BOOTCOUNT=y
 CONFIG_CMD_CACHE=y
 CONFIG_CMD_UUID=y
@@ -106,6 +111,8 @@ CONFIG_PHY_MICREL=y
 CONFIG_PHY_MICREL_KSZ90X1=y
 CONFIG_FEC_MXC=y
 CONFIG_MII=y
+CONFIG_SPL_PHY=y
+CONFIG_SPL_NOP_PHY=y
 CONFIG_PINCTRL=y
 CONFIG_SPL_PINCTRL=y
 CONFIG_PINCTRL_IMX8M=y
@@ -125,7 +132,15 @@ CONFIG_SYSRESET_PSCI=y
 CONFIG_SYSRESET_WATCHDOG=y
 CONFIG_DM_THERMAL=y
 CONFIG_USB=y
-# CONFIG_SPL_DM_USB is not set
 CONFIG_USB_EHCI_HCD=y
+CONFIG_MXC_USB_OTG_HACTIVE=y
+# CONFIG_USB_STORAGE is not set
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="Menlo"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_CI_UDC=y
+CONFIG_SDP_LOADADDR=0x40400000
+CONFIG_USB_GADGET_DOWNLOAD=y
 CONFIG_IMX_WATCHDOG=y
 CONFIG_OF_LIBFDT_OVERLAY=y
-- 
2.35.1