[PATCH v2 25/28] ARM: dts: rockchip: rv1126: Add Edgeble AI Edge Compute Module 0

Kever Yang kever.yang at rock-chips.com
Wed Sep 28 15:07:43 CEST 2022


Hi Jagan,

On 2022/8/18 22:52, Jagan Teki wrote:
> Edge Compute Module 0 is a 96boards SoM-CB compute module based
> on Rockchip RV1126 from Edgeble AI.
>
> General features:
> - Rockchip RV1126
> - 2/4GB LPDDR4
> - 16GB eMMC
> - Fn-link 8223A-SR WiFi/BT
>
> Edge Compute Module 0 needs to mount on top of Edgeble AI Carrier
> boards for creating complete platform solutions.
>
> Add support for it.
>
> Signed-off-by: Jagan Teki <jagan at edgeble.ai>

I would like to merge this patch after mainline kernel is available.


Thanks,
- Kever
> ---
> Changes for v2:
> - none
>
>   .../rv1126-edgeble-edge-compute-module-0.dtsi | 329 ++++++++++++++++++
>   1 file changed, 329 insertions(+)
>   create mode 100644 arch/arm/dts/rv1126-edgeble-edge-compute-module-0.dtsi
>
> diff --git a/arch/arm/dts/rv1126-edgeble-edge-compute-module-0.dtsi b/arch/arm/dts/rv1126-edgeble-edge-compute-module-0.dtsi
> new file mode 100644
> index 0000000000..c98232dd25
> --- /dev/null
> +++ b/arch/arm/dts/rv1126-edgeble-edge-compute-module-0.dtsi
> @@ -0,0 +1,329 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2020 Rockchip Electronics Co., Ltd.
> + * Copyright (c) 2022 Edgeble AI Technologies Pvt. Ltd.
> + */
> +
> +/ {
> +	compatible = "edgeble,edge-compute-module-0", "rockchip,rv1126";
> +
> +	aliases {
> +		mmc0 = &emmc;
> +	};
> +
> +	vcc5v0_sys: vccsys {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc5v0_sys";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +	};
> +
> +	vccio_flash: vccio-flash {
> +		compatible = "regulator-fixed";
> +		enable-active-high;
> +		gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&flash_vol_sel>;
> +		regulator-name = "vccio_flash";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vcc_3v3>;
> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		clocks = <&rk809 1>;
> +		clock-names = "ext_clock";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&wifi_enable_h>;
> +		reset-gpios = <&gpio1 RK_PD0 GPIO_ACTIVE_LOW>;
> +	};
> +};
> +
> +&cpu0 {
> +	cpu-supply = <&vdd_arm>;
> +};
> +
> +&emmc {
> +	bus-width = <8>;
> +	non-removable;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&emmc_bus8 &emmc_cmd &emmc_clk &emmc_rstnout>;
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&vccio_flash>;
> +	rockchip,default-sample-phase = <90>;
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +	clock-frequency = <400000>;
> +
> +	rk809: pmic at 20 {
> +		compatible = "rockchip,rk809";
> +		reg = <0x20>;
> +		interrupt-parent = <&gpio0>;
> +		interrupts = <RK_PB1 IRQ_TYPE_LEVEL_LOW>;
> +		#clock-cells = <1>;
> +		clock-output-names = "rk808-clkout1", "rk808-clkout2";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pmic_int_l>;
> +		rockchip,system-power-controller;
> +		wakeup-source;
> +
> +		vcc1-supply = <&vcc5v0_sys>;
> +		vcc2-supply = <&vcc5v0_sys>;
> +		vcc3-supply = <&vcc5v0_sys>;
> +		vcc4-supply = <&vcc5v0_sys>;
> +		vcc5-supply = <&vcc_buck5>;
> +		vcc6-supply = <&vcc_buck5>;
> +		vcc7-supply = <&vcc5v0_sys>;
> +		vcc8-supply = <&vcc3v3_sys>;
> +		vcc9-supply = <&vcc5v0_sys>;
> +
> +		regulators {
> +			vdd_npu_vepu: DCDC_REG1 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <650000>;
> +				regulator-max-microvolt = <950000>;
> +				regulator-ramp-delay = <6001>;
> +				regulator-initial-mode = <0x2>;
> +				regulator-name = "vdd_npu_vepu";
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdd_arm: DCDC_REG2 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <725000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-ramp-delay = <6001>;
> +				regulator-initial-mode = <0x2>;
> +				regulator-name = "vdd_arm";
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc_ddr: DCDC_REG3 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-initial-mode = <0x2>;
> +				regulator-name = "vcc_ddr";
> +
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +				};
> +			};
> +
> +			vcc3v3_sys: DCDC_REG4 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-initial-mode = <0x2>;
> +				regulator-name = "vcc3v3_sys";
> +
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <3300000>;
> +				};
> +			};
> +
> +			vcc_buck5: DCDC_REG5 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <2200000>;
> +				regulator-max-microvolt = <2200000>;
> +				regulator-name = "vcc_buck5";
> +
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <2200000>;
> +				};
> +			};
> +
> +			vcc_0v8: LDO_REG1 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <800000>;
> +				regulator-name = "vcc_0v8";
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc1v8_pmu: LDO_REG2 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcc1v8_pmu";
> +
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1800000>;
> +				};
> +			};
> +
> +			vdd0v8_pmu: LDO_REG3 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <800000>;
> +				regulator-name = "vcc0v8_pmu";
> +
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <800000>;
> +				};
> +			};
> +
> +			vcc_1v8: LDO_REG4 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcc_1v8";
> +
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1800000>;
> +				};
> +			};
> +
> +			vcc_dovdd: LDO_REG5 {
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcc_dovdd";
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc_dvdd: LDO_REG6 {
> +				regulator-min-microvolt = <1200000>;
> +				regulator-max-microvolt = <1200000>;
> +				regulator-name = "vcc_dvdd";
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc_avdd: LDO_REG7 {
> +				regulator-min-microvolt = <2800000>;
> +				regulator-max-microvolt = <2800000>;
> +				regulator-name = "vcc_avdd";
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vccio_sd: LDO_REG8 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vccio_sd";
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc3v3_sd: LDO_REG9 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcc3v3_sd";
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc_5v0: SWITCH_REG1 {
> +				regulator-name = "vcc_5v0";
> +			};
> +
> +			vcc_3v3: SWITCH_REG2 {
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-name = "vcc_3v3";
> +			};
> +		};
> +	};
> +};
> +
> +&pinctrl {
> +	flash {
> +		flash_vol_sel: flash-vol-sel {
> +			rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	pmic {
> +		pmic_int_l: pmic-int-l {
> +			rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
> +		};
> +	};
> +
> +	wifi {
> +		wifi_enable_h: wifi-enable-h {
> +			rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +};
> +
> +&pmu_io_domains {
> +	pmuio0-supply = <&vcc1v8_pmu>;
> +	pmuio1-supply = <&vcc3v3_sys>;
> +	vccio1-supply = <&vccio_flash>;
> +	vccio2-supply = <&vccio_sd>;
> +	vccio3-supply = <&vcc_1v8>;
> +	vccio4-supply = <&vcc_dovdd>;
> +	vccio5-supply = <&vcc_1v8>;
> +	vccio6-supply = <&vcc_1v8>;
> +	vccio7-supply = <&vcc_dovdd>;
> +	status = "okay";
> +};
> +
> +&saradc {
> +	vref-supply = <&vcc_1v8>;
> +	status = "okay";
> +};
> +
> +&sdio {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	max-frequency = <100000000>;
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	cap-sdio-irq;
> +	keep-power-in-suspend;
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +	non-removable;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sdmmc1_clk &sdmmc1_cmd &sdmmc1_bus4>;
> +	vmmc-supply = <&vcc3v3_sys>;
> +	vqmmc-supply = <&vcc_1v8>;
> +	rockchip,default-sample-phase = <90>;
> +	sd-uhs-sdr104;
> +	status = "okay";
> +};


More information about the U-Boot mailing list