[RFC] riscv: visionfive2: use OF_BOARD_SETUP
yanhong wang
yanhong.wang at starfivetech.com
Thu Apr 20 10:48:09 CEST 2023
On 2023/4/20 15:43, Torsten Duwe wrote:
> Hi Leo, thanks for the quick reply!
>
> On Thu, 20 Apr 2023 06:33:57 +0000
> Leo Liang <ycliang at andestech.com> wrote:
>
>> Hi, Torsten, Matthias,
>>
>> On Wed, Apr 19, 2023 at 02:34:03PM +0200, Matthias Brugger wrote:
>> >
>> >
>> > On 19/04/2023 13:28, Torsten Duwe wrote:
>
>> > > This is only a proof of concept; let me know if you like it and I
>> > > can add the other 12 DT patches to adjust_for_rev13b(), or maybe
>> > > start with 1.3b as the default and go the other way, or something
>> > > in between.
>
>> LGTM as well!
>
> Thank you very much! Again, this is only a PoC; if you agree with the
> concept, I clean it up and fill in the complete DT patching.
>
> Questions: shall I default to 1.3B and patch older 1.2A, or vice versa,
> or do it like your (starfive) patch set and start with something
> "neutral" and then patch both ways? And, more important, what is the
> correct interpretation of the board revision byte -- I assume it's
> offset 0x76 in the EEPROM? Is it always? Is ">= 0xB2" the correct
> discriminator?
>
Hi Torsten,
The attached is the driver of VisionFive2 EEPROM, which is only a preliminary draft,
and it is still being improved [the function has been tested, it is normal], and
it contains the definition of the EEPROM data format.
> Torsten
-------------- next part --------------
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2023 StarFive Technology Co., Ltd.
* Author: Yanhong Wang<yanhong.wang at starfivetech.com>
*/
#include <common.h>
#include <command.h>
#include <env.h>
#include <i2c.h>
#include <init.h>
#include <u-boot/crc.h>
#include <linux/delay.h>
#define FORMAT_VERSION 0x2
#define PCB_VERSION 0xB1
#define BOM_VERSION 'A'
/*
* BYTES_PER_EEPROM_PAGE: the 24FC04H datasheet says that data can
* only be written in page mode, which means 16 bytes at a time:
* 16-Byte Page Write Buffer
*/
#define BYTES_PER_EEPROM_PAGE 16
/*
* EEPROM_WRITE_DELAY_MS: the 24FC04H datasheet says it takes up to
* 5ms to complete a given write:
* Write Cycle Time (byte or page) ro Page Write Time 5 ms, Maximum
*/
#define EEPROM_WRITE_DELAY_MS 5000
/*
* StarFive OUI. Registration Date is 20xx-xx-xx
*/
#define STARFIVE_OUI_PREFIX "6C:CF:39:"
#define STARFIVE_DEFAULT_MAC0 "6C:CF:39:6C:DE:AD"
#define STARFIVE_DEFAULT_MAC1 "6C:CF:39:6C:DE:AE"
/* Magic number at the first four bytes of EEPROM HATs */
#define STARFIVE_EEPROM_HATS_SIG "SFVF" /* StarFive VisionFive */
#define STARFIVE_EEPROM_HATS_SIZE_MAX 256 /* Header + Atom1&4(v1) */
#define STARFIVE_EEPROM_WP_OFFSET 0 /* Read only field */
#define STARFIVE_EEPROM_ATOM1_PSTR "VF7110A1-2228-D008E000-00000001\0"
#define STARFIVE_EEPROM_ATOM1_PSTR_SIZE 32
#define STARFIVE_EEPROM_ATOM1_SN_OFFSET 23
#define STARFIVE_EEPROM_ATOM1_VSTR "StarFive Technology Co., Ltd.\0\0\0"
#define STARFIVE_EEPROM_ATOM1_VSTR_SIZE 32
#define MAGIC_NUMBER_BYTES 4
#define MAC_ADDR_BYTES 6
#define MAC_ADDR_STRLEN 17
/*
* Atom Types
* 0x0000 = invalid
* 0x0001 = vendor info
* 0x0002 = GPIO map
* 0x0003 = Linux device tree blob
* 0x0004 = manufacturer custom data
* 0x0005-0xfffe = reserved for future use
* 0xffff = invalid
*/
#define HATS_ATOM_INVALID 0x0000
#define HATS_ATOM_VENDOR 0x0001
#define HATS_ATOM_GPIO 0x0002
#define HATS_ATOM_DTB 0x0003
#define HATS_ATOM_CUSTOM 0x0004
#define HATS_ATOM_INVALID_END 0xffff
struct eeprom_header {
char signature[MAGIC_NUMBER_BYTES]; /* ASCII table signature */
u8 version; /* EEPROM data format version */
/* (0x00 reserved, 0x01 = first version) */
u8 reversed; /* 0x00, Reserved field */
u16 numatoms; /* total atoms in EEPROM */
u32 eeplen; /* total length in bytes of all eeprom data */
/* (including this header) */
};
struct eeprom_atom_header {
u16 type;
u16 count;
u32 dlen;
};
struct eeprom_atom1_data {
u8 uuid[16];
u16 pid;
u16 pver;
u8 vslen;
u8 pslen;
uchar vstr[STARFIVE_EEPROM_ATOM1_VSTR_SIZE];
uchar pstr[STARFIVE_EEPROM_ATOM1_PSTR_SIZE]; /* product SN */
};
struct starfive_eeprom_atom1 {
struct eeprom_atom_header header;
struct eeprom_atom1_data data;
u16 crc;
};
struct eeprom_atom4_data {
u16 version;
u8 pcb_revision; /* PCB version */
u8 bom_revision; /* BOM version */
u8 mac0_addr[MAC_ADDR_BYTES]; /* Ethernet0 MAC */
u8 mac1_addr[MAC_ADDR_BYTES]; /* Ethernet1 MAC */
u8 reserved[2];
};
struct starfive_eeprom_atom4 {
struct eeprom_atom_header header;
struct eeprom_atom4_data data;
u16 crc;
};
struct starfive_eeprom {
struct eeprom_header header;
struct starfive_eeprom_atom1 atom1;
struct starfive_eeprom_atom4 atom4;
};
static uchar eeprom_buf[STARFIVE_EEPROM_HATS_SIZE_MAX];
struct starfive_eeprom *pbuf = (struct starfive_eeprom *)eeprom_buf;
/* Set to 1 if we've read EEPROM into memory */
static int has_been_read;
static inline int is_match_magic(void)
{
return strncmp(pbuf->header.signature, STARFIVE_EEPROM_HATS_SIG,
MAGIC_NUMBER_BYTES);
}
/* Calculate the current CRC */
static inline u32 calculate_crc32(struct eeprom_atom_header *head)
{
uint len = sizeof(struct eeprom_atom_header) + head->dlen - sizeof(u16);
return crc32(0, (void *)head, len);
}
/* This function should be called after each update to the EEPROM structure */
static inline void update_crc(void)
{
pbuf->atom1.crc = calculate_crc32(&pbuf->atom1.header);
pbuf->atom4.crc = calculate_crc32(&pbuf->atom4.header);
}
static void dump_raw_eeprom(void)
{
unsigned int i;
u32 len;
len = sizeof(struct starfive_eeprom);
for (i = 0; i < len; i++) {
if ((i % 16) == 0)
printf("%02X: ", i);
printf("%02X ", ((u8 *)pbuf)[i]);
if (((i % 16) == 15) || (i == len - 1))
printf("\n");
}
}
/**
* show_eeprom - display the contents of the EEPROM
*/
static void show_eeprom(void)
{
if (has_been_read != 1)
return;
printf("\n--------EEPROM INFO--------\n");
printf("Vendor : %s\n", pbuf->atom1.data.vstr);
printf("Product full SN: %s\n", pbuf->atom1.data.pstr);
printf("data version: 0x%x\n", pbuf->atom4.data.version);
if (pbuf->atom4.data.version == 2) {
printf("PCB revision: 0x%x\n", pbuf->atom4.data.pcb_revision);
printf("BOM revision: %c\n", pbuf->atom4.data.bom_revision);
printf("Ethernet MAC0 address: %02x:%02x:%02x:%02x:%02x:%02x\n",
pbuf->atom4.data.mac0_addr[0], pbuf->atom4.data.mac0_addr[1],
pbuf->atom4.data.mac0_addr[2], pbuf->atom4.data.mac0_addr[3],
pbuf->atom4.data.mac0_addr[4], pbuf->atom4.data.mac0_addr[5]);
printf("Ethernet MAC1 address: %02x:%02x:%02x:%02x:%02x:%02x\n",
pbuf->atom4.data.mac1_addr[0], pbuf->atom4.data.mac1_addr[1],
pbuf->atom4.data.mac1_addr[2], pbuf->atom4.data.mac1_addr[3],
pbuf->atom4.data.mac1_addr[4], pbuf->atom4.data.mac1_addr[5]);
} else {
printf("Custom data v%d is not Supported\n", pbuf->atom4.data.version);
}
printf("--------EEPROM INFO--------\n\n");
}
/**
* set_mac_address() - stores a MAC address into the local EEPROM copy
*
* This function takes a pointer to MAC address string
* (i.e."XX:XX:XX:XX:XX:XX", where "XX" is a two-digit hex number),
* stores it in the MAC address field of the EEPROM local copy, and
* updates the local copy of the CRC.
*/
static void set_mac_address(char *string, int index)
{
u8 i;
u8 *mac;
if (strncasecmp(STARFIVE_OUI_PREFIX, string,
strlen(STARFIVE_OUI_PREFIX))) {
printf("The MAC address doesn't match StarFive OUI %s\n",
STARFIVE_OUI_PREFIX);
return;
}
mac = (index == 0) ? pbuf->atom4.data.mac0_addr :
pbuf->atom4.data.mac1_addr;
for (i = 0; *string && (i < MAC_ADDR_BYTES); i++) {
mac[i] = hextoul(string, &string);
if (*string == ':')
string++;
}
update_crc();
}
/**
* init_local_copy() - initialize the in-memory EEPROM copy
*
* Initialize the in-memory EEPROM copy with the magic number. Must
* be done when preparing to initialize a blank EEPROM, or overwrite
* one with a corrupted magic number.
*/
static void init_local_copy(void)
{
memset((void *)pbuf, 0, sizeof(struct starfive_eeprom));
memcpy(pbuf->header.signature, STARFIVE_EEPROM_HATS_SIG,
strlen(STARFIVE_EEPROM_HATS_SIG));
pbuf->header.version = FORMAT_VERSION;
pbuf->header.numatoms = 2;
pbuf->header.eeplen = sizeof(struct starfive_eeprom);
pbuf->atom1.header.type = HATS_ATOM_VENDOR;
pbuf->atom1.header.count = 1;
pbuf->atom1.header.dlen = sizeof(struct eeprom_atom1_data) + sizeof(u16);
pbuf->atom1.data.vslen = STARFIVE_EEPROM_ATOM1_VSTR_SIZE;
pbuf->atom1.data.pslen = STARFIVE_EEPROM_ATOM1_PSTR_SIZE;
memcpy(pbuf->atom1.data.vstr, STARFIVE_EEPROM_ATOM1_VSTR,
strlen(STARFIVE_EEPROM_ATOM1_VSTR));
memcpy(pbuf->atom1.data.pstr, STARFIVE_EEPROM_ATOM1_PSTR,
strlen(STARFIVE_EEPROM_ATOM1_PSTR));
pbuf->atom4.header.type = HATS_ATOM_CUSTOM;
pbuf->atom4.header.count = 2;
pbuf->atom4.header.dlen = sizeof(struct eeprom_atom4_data) + sizeof(u16);
pbuf->atom4.data.version = FORMAT_VERSION;
pbuf->atom4.data.pcb_revision = PCB_VERSION;
pbuf->atom4.data.bom_revision = BOM_VERSION;
set_mac_address(STARFIVE_DEFAULT_MAC0, 0);
set_mac_address(STARFIVE_DEFAULT_MAC1, 1);
}
/**
* prog_eeprom() - write the EEPROM from memory
*/
static int prog_eeprom(unsigned int size)
{
unsigned int i;
void *p;
uchar tmp_buff[STARFIVE_EEPROM_HATS_SIZE_MAX];
struct udevice *dev;
int ret;
if (is_match_magic()) {
printf("MAGIC ERROR, Please check the data@%p.\n", pbuf);
return -1;
}
ret = i2c_get_chip_for_busnum(CONFIG_SYS_EEPROM_BUS_NUM,
CONFIG_SYS_I2C_EEPROM_ADDR,
CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
&dev);
if (ret) {
printf("Get i2c bus:%d addr:%d fail.\n", CONFIG_SYS_EEPROM_BUS_NUM,
CONFIG_SYS_I2C_EEPROM_ADDR);
return ret;
}
for (i = 0, p = (u8 *)pbuf; i < size; ) {
if (!ret)
ret = dm_i2c_write(dev, i, p, min((int)(size - i),
BYTES_PER_EEPROM_PAGE));
if (ret)
break;
udelay(EEPROM_WRITE_DELAY_MS);
i += BYTES_PER_EEPROM_PAGE;
p += BYTES_PER_EEPROM_PAGE;
}
if (!ret) {
/* Verify the write by reading back the EEPROM and comparing */
ret = dm_i2c_read(dev,
STARFIVE_EEPROM_WP_OFFSET,
tmp_buff,
STARFIVE_EEPROM_HATS_SIZE_MAX);
if (!ret && memcmp((void *)pbuf, (void *)tmp_buff,
STARFIVE_EEPROM_HATS_SIZE_MAX))
ret = -1;
}
if (ret) {
has_been_read = -1;
printf("Programming failed.\n");
return -1;
}
printf("Programming passed.\n");
return 0;
}
/**
* read_eeprom() - read the EEPROM into memory, if it hasn't been read already
*/
static int read_eeprom(void)
{
int ret;
struct udevice *dev;
if (has_been_read == 1)
return 0;
ret = i2c_get_chip_for_busnum(CONFIG_SYS_EEPROM_BUS_NUM,
CONFIG_SYS_I2C_EEPROM_ADDR, 1, &dev);
if (!ret)
ret = dm_i2c_read(dev, 0, (u8 *)pbuf,
STARFIVE_EEPROM_HATS_SIZE_MAX);
has_been_read = (ret == 0) ? 1 : 0;
return ret;
}
/**
* set_pcb_revision() - stores a StarFive PCB revision into the local EEPROM copy
*
* Takes a pointer to a string representing the numeric PCB revision in
* decimal ("0" - "255"), stores it in the pcb_revision field of the
* EEPROM local copy, and updates the CRC of the local copy.
*/
static void set_pcb_revision(char *string)
{
u32 p;
p = simple_strtoul(string, &string, 16);
if (p > U8_MAX) {
printf("%s must not be greater than %d\n", "PCB revision",
U8_MAX);
return;
}
pbuf->atom4.data.pcb_revision = p;
update_crc();
}
/**
* set_bom_revision() - stores a StarFive BOM revision into the local EEPROM copy
*
* Takes a pointer to a uppercase ASCII character representing the BOM
* revision ("A" - "Z"), stores it in the bom_revision field of the
* EEPROM local copy, and updates the CRC of the local copy.
*/
static void set_bom_revision(char *string)
{
if (string[0] < 'A' || string[0] > 'Z') {
printf("BOM revision must be an uppercase letter between A and Z\n");
return;
}
pbuf->atom4.data.bom_revision = string[0];
update_crc();
}
/**
* set_product_id() - stores a StarFive product ID into the local EEPROM copy
*
* Takes a pointer to a string representing the numeric product ID in
* string ("VF7100A1-2150-D008E000-00000001\0"), stores it in the product string
* field of the EEPROM local copy, and updates the CRC of the local copy.
*/
static void set_product_id(char *string)
{
u32 len;
len = (strlen(string) > STARFIVE_EEPROM_ATOM1_PSTR_SIZE) ?
STARFIVE_EEPROM_ATOM1_PSTR_SIZE : strlen(string);
memcpy((void *)pbuf->atom1.data.pstr, (void *)string, len);
update_crc();
}
static int print_usage(void)
{
printf("display and program the system ID and MAC addresses in EEPROM\n"
"[read_eeprom|initialize|write_eeprom|mac_address|pcb_revision|bom_revision|product_id]\n"
"mac read_eeprom\n"
" - read EEPROM content into memory data structure\n"
"mac write_eeprom\n"
" - save memory data structure to the EEPROM\n"
"mac initialize\n"
" - initialize the in-memory EEPROM copy with default data\n"
"mac mac0_address <xx:xx:xx:xx:xx:xx>\n"
" - stores a MAC0 address into the local EEPROM copy\n"
"mac mac1_address <xx:xx:xx:xx:xx:xx>\n"
" - stores a MAC1 address into the local EEPROM copy\n"
"mac pcb_revision <?>\n"
" - stores a StarFive PCB revision into the local EEPROM copy\n"
"mac bom_revision <A>\n"
" - stores a StarFive BOM revision into the local EEPROM copy\n"
"mac product_id <VF7110A1-2228-D008E000-xxxxxxxx>\n"
" - stores a StarFive product ID into the local EEPROM copy\n");
return 0;
}
int do_mac(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
{
char *cmd;
if (argc == 1) {
show_eeprom();
return 0;
}
if (argc > 3)
return print_usage();
cmd = argv[1];
/* Commands with no argument */
if (!strcmp(cmd, "read_eeprom")) {
has_been_read = 0;
return read_eeprom();
} else if (!strcmp(cmd, "initialize")) {
init_local_copy();
return 0;
} else if (!strcmp(cmd, "write_eeprom")) {
return prog_eeprom(STARFIVE_EEPROM_HATS_SIZE_MAX);
}
if (argc != 3)
return print_usage();
if (is_match_magic()) {
printf("Please read the EEPROM ('read_eeprom') and/or initialize the EEPROM ('initialize') first.\n");
return 0;
}
if (!strcmp(cmd, "mac0_address")) {
set_mac_address(argv[2], 0);
return 0;
} else if (!strcmp(cmd, "mac1_address")) {
set_mac_address(argv[2], 1);
return 0;
} else if (!strcmp(cmd, "pcb_revision")) {
set_pcb_revision(argv[2]);
return 0;
} else if (!strcmp(cmd, "bom_revision")) {
set_bom_revision(argv[2]);
return 0;
} else if (!strcmp(cmd, "product_id")) {
set_product_id(argv[2]);
return 0;
}
return print_usage();
}
/**
* mac_read_from_eeprom() - read the MAC address & the serial number in EEPROM
*
* This function reads the MAC address and the serial number from EEPROM and
* sets the appropriate environment variables for each one read.
*
* The environment variables are only set if they haven't been set already.
* This ensures that any user-saved variables are never overwritten.
*
* If CONFIG_ID_EEPROM is enabled, this function will be called in
* "static init_fnc_t init_sequence_r[]" of u-boot/common/board_r.c.
*/
int mac_read_from_eeprom(void)
{
/**
* try to fill the buff from EEPROM,
* always return SUCCESS, even some error happens.
*/
if (read_eeprom()) {
dump_raw_eeprom();
return 0;
}
// 1, setup ethaddr env
eth_env_set_enetaddr("eth0addr", pbuf->atom4.data.mac0_addr);
eth_env_set_enetaddr("eth1addr", pbuf->atom4.data.mac1_addr);
/**
* 2, setup serial# env, reference to hifive-platform-i2c-eeprom.c,
* serial# can be a ASCII string, but not just a hex number, so we
* setup serial# in the 32Byte format:
* "VF7100A1-2201-D008E000-00000001;"
* "<product>-<date>-<DDR&eMMC>-<serial_number>"
* <date>: 4Byte, should be the output of `date +%y%W`
* <DDR&eMMC>: 8Byte, "D008" means 8GB, "D01T" means 1TB;
* "E000" means no eMMC，"E032" means 32GB, "E01T" means 1TB.
* <serial_number>: 8Byte, the Unique Identifier of board in hex.
*/
if (!env_get("serial#"))
env_set("serial#", pbuf->atom1.data.pstr);
printf("StarFive EEPROM format v%u\n", pbuf->header.version);
show_eeprom();
return 0;
}
/**
* get_pcb_revision_from_eeprom - get the PCB revision
*
* 1.2A board return 'A'/'a', 1.3B return 'B'/'b',other values are illegal
*/
u8 get_pcb_revision_from_eeprom(void)
{
u8 pv = 0xFF;
if (read_eeprom())
return pv;
return pbuf->atom1.data.pstr[6];
}
/**
* get_ddr_size_from_eeprom - get the DDR size
* pstr: VF7110A1-2228-D008E000-00000001
* VF7110A1/VF7110B1 : VisionFive JH7110A /VisionFive JH7110B
* D008: 8GB LPDDR4
*/
u32 get_ddr_size_from_eeprom(void)
{
u32 pv = 0xFFFFFFFF;
if (read_eeprom())
return pv;
return hextoul(&pbuf->atom1.data.pstr[14], NULL);
}
More information about the U-Boot
mailing list