[PATCH v4] rockchip: rk3568: Add EmbedFire Lubancat 2 support

Kever Yang kever.yang at rock-chips.com
Mon Aug 7 02:45:05 CEST 2023


On 2023/8/5 20:00, Andy Yan wrote:
> LubanCat2 is a rk3568 based SBC from EmbedFire.
>
> Specification:
> - Rockchip rk3568
> - LPDDR4/4X 1/2/4/8 GB
> - TF scard slot
> - eMMC 8/32/64/128 GB
> - Gigabit ethernet x 2
> - HDMI out
> - USB 2.0 Host x 1
> - USB 2.0 Type-C OTG x 1
> - USB 3.0 Host x 1
> - Mini PCIE interface for WIFI/BT module
> - M.2 key for 2280 NVME
> - 40 pin header
>
> The dts file is sync from linux mainline.
>
> Signed-off-by: Andy Yan <andyshrk at 163.com>
Reviewed-by: Kever Yang <kever.yang at rock-chips.com>

Thanks,
- Kever
>
> ---
>
> Changes in v4:
> - Add entry for this board to evb_rk3568/MAINTAINERS
> - document this board at doc/board/rockchip/rockchip.rst
> - restore the  copyright header of dts from linux kernel
> - remove ETH_DESIGNWARE from defconfig
> - remove mmc-hs200-1_8v from u-boot.dsti
>
> Changes in v3:
> - some alphabetical order update
> - disable all SPI flash related options.
> - remove bootph-all for pinctrl
> - add emmc_datastrobe pinconfig for hs200/hs400 in u-boot.dtsi
> - use USB_DWC3_GENERIC driver as Jonas suggested.
> - add CONFIG_SPL_DM_SEQ_ALIAS
>
> Changes in v2:
> - enable SPL_FIT_SIGNATURE
>
>   arch/arm/dts/Makefile                      |   1 +
>   arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi |  27 +
>   arch/arm/dts/rk3568-lubancat-2.dts         | 733 +++++++++++++++++++++
>   board/rockchip/evb_rk3568/MAINTAINERS      |   7 +
>   configs/lubancat-2-rk3568_defconfig        |  85 +++
>   doc/board/rockchip/rockchip.rst            |   1 +
>   6 files changed, 854 insertions(+)
>   create mode 100644 arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi
>   create mode 100644 arch/arm/dts/rk3568-lubancat-2.dts
>   create mode 100644 configs/lubancat-2-rk3568_defconfig
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index bd518064f3..64c885dcf9 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -178,6 +178,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3568) += \
>   	rk3566-soquartz-cm4.dtb \
>   	rk3566-soquartz-model-a.dtb \
>   	rk3568-evb.dtb \
> +	rk3568-lubancat-2.dtb \
>   	rk3568-nanopi-r5c.dtb \
>   	rk3568-nanopi-r5s.dtb \
>   	rk3568-odroid-m1.dtb \
> diff --git a/arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi b/arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi
> new file mode 100644
> index 0000000000..27c6277523
> --- /dev/null
> +++ b/arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi
> @@ -0,0 +1,27 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * (C) Copyright 2023 Rockchip Electronics Co., Ltd
> + * (C) Copyright 2023 Andy Yan <andyshrk at 163.com>
> + */
> +
> +#include "rk356x-u-boot.dtsi"
> +
> +/ {
> +	chosen {
> +		stdout-path = &uart2;
> +	};
> +};
> +
> +&sdhci {
> +	cap-mmc-highspeed;
> +	mmc-ddr-1_8v;
> +	mmc-hs400-1_8v;
> +	mmc-hs400-enhanced-strobe;
> +	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
> +};
> +
> +&uart2 {
> +	bootph-all;
> +	clock-frequency = <24000000>;
> +	status = "okay";
> +};
> diff --git a/arch/arm/dts/rk3568-lubancat-2.dts b/arch/arm/dts/rk3568-lubancat-2.dts
> new file mode 100644
> index 0000000000..e653b067aa
> --- /dev/null
> +++ b/arch/arm/dts/rk3568-lubancat-2.dts
> @@ -0,0 +1,733 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/*
> + * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
> + * Copyright (c) 2022 EmbedFire <embedfire at embedfire.com>
> + */
> +
> +/dts-v1/;
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/rockchip.h>
> +#include <dt-bindings/soc/rockchip,vop2.h>
> +#include "rk3568.dtsi"
> +
> +/ {
> +	model = "EmbedFire LubanCat 2";
> +	compatible = "embedfire,lubancat-2", "rockchip,rk3568";
> +
> +	aliases {
> +		ethernet0 = &gmac0;
> +		ethernet1 = &gmac1;
> +		mmc0 = &sdmmc0;
> +		mmc1 = &sdhci;
> +	};
> +
> +	chosen: chosen {
> +		stdout-path = "serial2:1500000n8";
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		user_led: user-led {
> +			label = "user_led";
> +			linux,default-trigger = "heartbeat";
> +			default-state = "on";
> +			gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_LOW>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&user_led_pin>;
> +		};
> +	};
> +
> +	hdmi-con {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con_in: endpoint {
> +				remote-endpoint = <&hdmi_out_con>;
> +			};
> +		};
> +	};
> +
> +	dc_5v: dc-5v-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "dc_5v";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +	};
> +
> +	vcc3v3_sys: vcc3v3-sys-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc3v3_sys";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc5v0_sys>;
> +	};
> +
> +	vcc5v0_sys: vcc5v0-sys-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc5v0_sys";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&dc_5v>;
> +	};
> +
> +	vcc3v3_m2_pcie: vcc3v3-m2-pcie-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "m2_pcie_3v3";
> +		enable-active-high;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
> +		pinctrl-0 = <&vcc3v3_m2_pcie_en>;
> +		pinctrl-names = "default";
> +		startup-delay-us = <200000>;
> +		vin-supply = <&vcc5v0_sys>;
> +	};
> +
> +	vcc3v3_mini_pcie: vcc3v3-mini-pcie-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "minipcie_3v3";
> +		enable-active-high;
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpio3 RK_PC3 GPIO_ACTIVE_HIGH>;
> +		pinctrl-0 = <&vcc3v3_mini_pcie_en>;
> +		pinctrl-names = "default";
> +		startup-delay-us = <5000>;
> +		vin-supply = <&vcc5v0_sys>;
> +	};
> +
> +	vcc5v0_usb20_host: vcc5v0-usb20-host-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc5v0_usb20_host";
> +		enable-active-high;
> +		gpio = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
> +		pinctrl-0 = <&vcc5v0_usb20_host_en>;
> +		pinctrl-names = "default";
> +	};
> +
> +	vcc5v0_usb30_host: vcc5v0-usb30-host-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc5v0_usb30_host";
> +		enable-active-high;
> +		gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_HIGH>;
> +		pinctrl-0 = <&vcc5v0_usb30_host_en>;
> +		pinctrl-names = "default";
> +	};
> +
> +	vcc5v0_otg_vbus: vcc5v0-otg-vbus-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc5v0_otg_vbus";
> +		enable-active-high;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		gpio = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
> +		pinctrl-0 = <&vcc5v0_otg_vbus_en>;
> +		pinctrl-names = "default";
> +	};
> +};
> +
> +&combphy0 {
> +	status = "okay";
> +};
> +
> +&combphy1 {
> +	status = "okay";
> +};
> +
> +&combphy2 {
> +	status = "okay";
> +};
> +
> +&cpu0 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu1 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu2 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&cpu3 {
> +	cpu-supply = <&vdd_cpu>;
> +};
> +
> +&gpu {
> +	mali-supply = <&vdd_gpu>;
> +	status = "okay";
> +};
> +
> +&hdmi {
> +	avdd-0v9-supply = <&vdda0v9_image>;
> +	avdd-1v8-supply = <&vcca1v8_image>;
> +	status = "okay";
> +};
> +
> +&hdmi_in {
> +	hdmi_in_vp0: endpoint {
> +		remote-endpoint = <&vp0_out_hdmi>;
> +	};
> +};
> +
> +&hdmi_out {
> +	hdmi_out_con: endpoint {
> +		remote-endpoint = <&hdmi_con_in>;
> +	};
> +};
> +
> +&hdmi_sound {
> +	status = "okay";
> +};
> +
> +&i2c0 {
> +	status = "okay";
> +
> +	vdd_cpu: regulator at 1c {
> +		compatible = "tcs,tcs4525";
> +		reg = <0x1c>;
> +		fcs,suspend-voltage-selector = <1>;
> +		regulator-name = "vdd_cpu";
> +		regulator-always-on;
> +		regulator-boot-on;
> +		regulator-min-microvolt = <800000>;
> +		regulator-max-microvolt = <1150000>;
> +		regulator-ramp-delay = <2300>;
> +		vin-supply = <&vcc5v0_sys>;
> +
> +		regulator-state-mem {
> +			regulator-off-in-suspend;
> +		};
> +	};
> +
> +	rk809: pmic at 20 {
> +		compatible = "rockchip,rk809";
> +		reg = <0x20>;
> +		interrupt-parent = <&gpio0>;
> +		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
> +		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
> +		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
> +		#clock-cells = <1>;
> +		clock-names = "mclk";
> +		clocks = <&cru I2S1_MCLKOUT_TX>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pmic_int>;
> +		rockchip,system-power-controller;
> +		#sound-dai-cells = <0>;
> +		vcc1-supply = <&vcc3v3_sys>;
> +		vcc2-supply = <&vcc3v3_sys>;
> +		vcc3-supply = <&vcc3v3_sys>;
> +		vcc4-supply = <&vcc3v3_sys>;
> +		vcc5-supply = <&vcc3v3_sys>;
> +		vcc6-supply = <&vcc3v3_sys>;
> +		vcc7-supply = <&vcc3v3_sys>;
> +		vcc8-supply = <&vcc3v3_sys>;
> +		vcc9-supply = <&vcc3v3_sys>;
> +		wakeup-source;
> +
> +		regulators {
> +			vdd_logic: DCDC_REG1 {
> +				regulator-name = "vdd_logic";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <500000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-init-microvolt = <900000>;
> +				regulator-ramp-delay = <6001>;
> +				regulator-initial-mode = <0x2>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdd_gpu: DCDC_REG2 {
> +				regulator-name = "vdd_gpu";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <500000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-init-microvolt = <900000>;
> +				regulator-ramp-delay = <6001>;
> +				regulator-initial-mode = <0x2>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc_ddr: DCDC_REG3 {
> +				regulator-name = "vcc_ddr";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-initial-mode = <0x2>;
> +
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +				};
> +			};
> +
> +			vdd_npu: DCDC_REG4 {
> +				regulator-name = "vdd_npu";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <500000>;
> +				regulator-max-microvolt = <1350000>;
> +				regulator-init-microvolt = <900000>;
> +				regulator-ramp-delay = <6001>;
> +				regulator-initial-mode = <0x2>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc_1v8: DCDC_REG5 {
> +				regulator-name = "vcc_1v8";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdda0v9_image: LDO_REG1 {
> +				regulator-name = "vdda0v9_image";
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <900000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdda_0v9: LDO_REG2 {
> +				regulator-name = "vdda_0v9";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <900000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vdda0v9_pmu: LDO_REG3 {
> +				regulator-name = "vdda0v9_pmu";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <900000>;
> +				regulator-max-microvolt = <900000>;
> +
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <900000>;
> +				};
> +			};
> +
> +			vccio_acodec: LDO_REG4 {
> +				regulator-name = "vccio_acodec";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vccio_sd: LDO_REG5 {
> +				regulator-name = "vccio_sd";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc3v3_pmu: LDO_REG6 {
> +				regulator-name = "vcc3v3_pmu";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <3300000>;
> +				};
> +			};
> +
> +			vcca_1v8: LDO_REG7 {
> +				regulator-name = "vcca_1v8";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcca1v8_pmu: LDO_REG8 {
> +				regulator-name = "vcca1v8_pmu";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +
> +				regulator-state-mem {
> +					regulator-on-in-suspend;
> +					regulator-suspend-microvolt = <1800000>;
> +				};
> +			};
> +
> +			vcca1v8_image: LDO_REG9 {
> +				regulator-name = "vcca1v8_image";
> +				regulator-always-on;
> +				regulator-boot-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc_3v3: SWITCH_REG1 {
> +				regulator-name = "vcc_3v3";
> +				regulator-always-on;
> +				regulator-boot-on;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +
> +			vcc3v3_sd: SWITCH_REG2 {
> +				regulator-name = "vcc3v3_sd";
> +				regulator-always-on;
> +				regulator-boot-on;
> +
> +				regulator-state-mem {
> +					regulator-off-in-suspend;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&i2s1_8ch {
> +	rockchip,trcm-sync-tx-only;
> +	status = "okay";
> +};
> +
> +&gmac0 {
> +	phy-mode = "rgmii";
> +	clock_in_out = "output";
> +
> +	snps,reset-gpio = <&gpio2 RK_PD3 GPIO_ACTIVE_LOW>;
> +	snps,reset-active-low;
> +	/* Reset time is 20ms, 100ms for rtl8211f */
> +	snps,reset-delays-us = <0 20000 100000>;
> +
> +	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
> +	assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&gmac0_miim
> +		     &gmac0_tx_bus2
> +		     &gmac0_rx_bus2
> +		     &gmac0_rgmii_clk
> +		     &gmac0_rgmii_bus>;
> +
> +	tx_delay = <0x22>;
> +	rx_delay = <0x0e>;
> +
> +	phy-handle = <&rgmii_phy0>;
> +	status = "okay";
> +};
> +
> +&mdio0 {
> +	rgmii_phy0: phy at 0 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <0x0>;
> +	};
> +};
> +
> +&gmac1 {
> +	phy-mode = "rgmii";
> +	clock_in_out = "output";
> +
> +	snps,reset-gpio = <&gpio3 RK_PA2 GPIO_ACTIVE_LOW>;
> +	snps,reset-active-low;
> +	/* Reset time is 20ms, 100ms for rtl8211f */
> +	snps,reset-delays-us = <0 20000 100000>;
> +
> +	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
> +	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&gmac1m1_miim
> +		     &gmac1m1_tx_bus2
> +		     &gmac1m1_rx_bus2
> +		     &gmac1m1_rgmii_clk
> +		     &gmac1m1_rgmii_bus>;
> +
> +	tx_delay = <0x21>;
> +	rx_delay = <0x0e>;
> +
> +	phy-handle = <&rgmii_phy1>;
> +	status = "okay";
> +};
> +
> +&mdio1 {
> +	rgmii_phy1: phy at 0 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <0x0>;
> +	};
> +};
> +
> +&gic {
> +	mbi-ranges = <94 31>, <229 31>, <289 31>;
> +};
> +
> +&pcie30phy {
> +	status = "okay";
> +};
> +
> +&pcie3x2 {
> +	reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
> +	vpcie3v3-supply = <&vcc3v3_m2_pcie>;
> +	status = "okay";
> +};
> +
> +&pcie2x1 {
> +	reset-gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_HIGH>;
> +	disable-gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_HIGH>;
> +	vpcie3v3-supply = <&vcc3v3_mini_pcie>;
> +	status = "okay";
> +};
> +
> +&pmu_io_domains {
> +	pmuio2-supply = <&vcc3v3_pmu>;
> +	vccio1-supply = <&vccio_acodec>;
> +	vccio3-supply = <&vccio_sd>;
> +	vccio4-supply = <&vcc_1v8>;
> +	vccio5-supply = <&vcc_3v3>;
> +	vccio6-supply = <&vcc_1v8>;
> +	vccio7-supply = <&vcc_3v3>;
> +	status = "okay";
> +};
> +
> +&pwm8 {
> +	status = "okay";
> +};
> +
> +&pwm9 {
> +	status = "disabled";
> +};
> +
> +&pwm10 {
> +	status = "disabled";
> +};
> +
> +&pwm14 {
> +	status = "disabled";
> +};
> +
> +&spi3 {
> +	pinctrl-0 = <&spi3m1_pins>;
> +	status = "disabled";
> +};
> +
> +&uart2 {
> +	status = "okay";
> +};
> +
> +&uart3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart3m1_xfer>;
> +	status = "disabled";
> +};
> +
> +&saradc {
> +	vref-supply = <&vcca_1v8>;
> +	status = "okay";
> +};
> +
> +&tsadc {
> +	rockchip,hw-tshut-mode = <1>;
> +	rockchip,hw-tshut-polarity = <0>;
> +	status = "okay";
> +};
> +
> +&sdhci {
> +	assigned-clocks = <&cru BCLK_EMMC>, <&cru TCLK_EMMC>, <&cru CCLK_EMMC>;
> +	assigned-clock-rates = <200000000>, <24000000>, <200000000>;
> +	bus-width = <8>;
> +	max-frequency = <200000000>;
> +	mmc-hs200-1_8v;
> +	non-removable;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>;
> +	supports-emmc;
> +	status = "okay";
> +};
> +
> +&sdmmc0 {
> +	max-frequency = <150000000>;
> +	no-sdio;
> +	no-mmc;
> +	bus-width = <4>;
> +	cap-mmc-highspeed;
> +	cap-sd-highspeed;
> +	disable-wp;
> +	sd-uhs-sdr104;
> +	vmmc-supply = <&vcc3v3_sd>;
> +	vqmmc-supply = <&vccio_sd>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
> +	status = "okay";
> +};
> +
> +/* USB OTG/USB Host_1 USB 2.0 Comb */
> +&usb2phy0 {
> +	status = "okay";
> +};
> +
> +&usb2phy0_host {
> +	phy-supply = <&vcc5v0_usb30_host>;
> +	status = "okay";
> +};
> +
> +&usb2phy0_otg {
> +	phy-supply = <&vcc5v0_otg_vbus>;
> +	status = "okay";
> +};
> +
> +&usb_host0_ehci {
> +	status = "okay";
> +};
> +
> +&usb_host0_ohci {
> +	status = "okay";
> +};
> +
> +/* USB Host_2/USB Host_3 USB 2.0 Comb */
> +&usb2phy1 {
> +	status = "okay";
> +};
> +
> +&usb2phy1_host {
> +	status = "okay";
> +};
> +
> +&usb2phy1_otg {
> +	phy-supply = <&vcc5v0_usb20_host>;
> +	status = "okay";
> +};
> +
> +&usb_host1_ehci {
> +	status = "okay";
> +};
> +
> +&usb_host1_ohci {
> +	status = "okay";
> +};
> +
> +/* MULTI_PHY0 For SATA0, USB3.0 OTG Only USB2.0 */
> +&usb_host0_xhci {
> +	phys = <&usb2phy0_otg>;
> +	phy-names = "usb2-phy";
> +	extcon = <&usb2phy0>;
> +	maximum-speed = "high-speed";
> +	dr_mode = "host";
> +	status = "okay";
> +};
> +
> +&sata0 {
> +	status = "okay";
> +};
> +
> +/* USB3.0 Host */
> +&usb_host1_xhci {
> +	status = "okay";
> +};
> +
> +&vop {
> +	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
> +	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
> +	status = "okay";
> +};
> +
> +&vop_mmu {
> +	status = "okay";
> +};
> +
> +&vp0 {
> +	vp0_out_hdmi: endpoint at ROCKCHIP_VOP2_EP_HDMI0 {
> +		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
> +		remote-endpoint = <&hdmi_in_vp0>;
> +	};
> +};
> +
> +&pinctrl {
> +	leds {
> +		user_led_pin: user-status-led-pin {
> +			rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	usb {
> +		vcc5v0_usb20_host_en: vcc5v0-usb20-host-en {
> +			rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
> +		vcc5v0_usb30_host_en: vcc5v0-usb30-host-en {
> +			rockchip,pins = <0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
> +		vcc5v0_otg_vbus_en: vcc5v0-otg-vbus-en {
> +			rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	pcie {
> +		vcc3v3_m2_pcie_en: vcc3v3-m2-pcie-en {
> +			rockchip,pins = <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +
> +		vcc3v3_mini_pcie_en: vcc3v3-mini-pcie-en {
> +			rockchip,pins = <3 RK_PC3 RK_FUNC_GPIO &pcfg_pull_none>;
> +		};
> +	};
> +
> +	pmic {
> +		pmic_int: pmic-int {
> +			rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
> +		};
> +	};
> +};
> diff --git a/board/rockchip/evb_rk3568/MAINTAINERS b/board/rockchip/evb_rk3568/MAINTAINERS
> index 82a92b89fa..1cdeafcf79 100644
> --- a/board/rockchip/evb_rk3568/MAINTAINERS
> +++ b/board/rockchip/evb_rk3568/MAINTAINERS
> @@ -7,6 +7,13 @@ F:      configs/evb-rk3568_defconfig
>   F:	arch/arm/dts/rk3568-evb-boot.dtsi
>   F:	arch/arm/dts/rk3568-evb.dts
>   
> +Lubancat-2
> +M:	Andy Yan <andyshrk at 163.com>
> +S:	Maintained
> +F:	configs/lubancat-2-rk3568_defconfig
> +F:	arch/arm/dts/rk3568-lubancat-2.dts
> +F:	arch/arm/dts/rk3568-lubancat-2-u-boot.dtsi
> +
>   NANOPI-R5C
>   M:      Tianling Shen <cnsztl at gmail.com>
>   S:      Maintained
> diff --git a/configs/lubancat-2-rk3568_defconfig b/configs/lubancat-2-rk3568_defconfig
> new file mode 100644
> index 0000000000..b01d3bd2a1
> --- /dev/null
> +++ b/configs/lubancat-2-rk3568_defconfig
> @@ -0,0 +1,85 @@
> +CONFIG_ARM=y
> +CONFIG_SKIP_LOWLEVEL_INIT=y
> +CONFIG_COUNTER_FREQUENCY=24000000
> +CONFIG_ARCH_ROCKCHIP=y
> +CONFIG_TEXT_BASE=0x00a00000
> +CONFIG_SPL_LIBCOMMON_SUPPORT=y
> +CONFIG_SPL_LIBGENERIC_SUPPORT=y
> +CONFIG_NR_DRAM_BANKS=2
> +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
> +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xc00000
> +CONFIG_DEFAULT_DEVICE_TREE="rk3568-lubancat-2"
> +CONFIG_ROCKCHIP_RK3568=y
> +CONFIG_SPL_ROCKCHIP_COMMON_BOARD=y
> +CONFIG_SPL_SERIAL=y
> +CONFIG_SPL_STACK_R_ADDR=0x600000
> +CONFIG_SPL_STACK=0x400000
> +CONFIG_DEBUG_UART_BASE=0xFE660000
> +CONFIG_DEBUG_UART_CLOCK=24000000
> +CONFIG_SYS_LOAD_ADDR=0xc00800
> +CONFIG_DEBUG_UART=y
> +CONFIG_FIT=y
> +CONFIG_FIT_VERBOSE=y
> +CONFIG_SPL_FIT_SIGNATURE=y
> +CONFIG_SPL_LOAD_FIT=y
> +CONFIG_LEGACY_IMAGE_FORMAT=y
> +CONFIG_DEFAULT_FDT_FILE="rockchip/rk3568-lubancat-2.dtb"
> +# CONFIG_DISPLAY_CPUINFO is not set
> +CONFIG_DISPLAY_BOARDINFO_LATE=y
> +CONFIG_SPL_MAX_SIZE=0x40000
> +CONFIG_SPL_PAD_TO=0x7f8000
> +CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
> +CONFIG_SPL_BSS_START_ADDR=0x4000000
> +CONFIG_SPL_BSS_MAX_SIZE=0x4000
> +# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
> +# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
> +CONFIG_SPL_STACK_R=y
> +CONFIG_SPL_ATF=y
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_GPT=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_USB=y
> +# CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_PMIC=y
> +CONFIG_CMD_REGULATOR=y
> +# CONFIG_SPL_DOS_PARTITION is not set
> +CONFIG_SPL_OF_CONTROL=y
> +CONFIG_OF_LIVE=y
> +CONFIG_OF_SPL_REMOVE_PROPS="clock-names interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
> +CONFIG_SPL_DM_SEQ_ALIAS=y
> +CONFIG_SPL_REGMAP=y
> +CONFIG_SPL_SYSCON=y
> +CONFIG_SPL_CLK=y
> +CONFIG_ROCKCHIP_GPIO=y
> +CONFIG_SYS_I2C_ROCKCHIP=y
> +CONFIG_MISC=y
> +CONFIG_SUPPORT_EMMC_RPMB=y
> +CONFIG_MMC_DW=y
> +CONFIG_MMC_DW_ROCKCHIP=y
> +CONFIG_MMC_SDHCI=y
> +CONFIG_MMC_SDHCI_SDMA=y
> +CONFIG_MMC_SDHCI_ROCKCHIP=y
> +# CONFIG_SPI_FLASH is not set
> +CONFIG_PHY_ROCKCHIP_INNO_USB2=y
> +CONFIG_PHY_ROCKCHIP_NANENG_COMBOPHY=y
> +CONFIG_SPL_PINCTRL=y
> +CONFIG_DM_PMIC=y
> +CONFIG_PMIC_RK8XX=y
> +CONFIG_REGULATOR_RK8XX=y
> +CONFIG_PWM_ROCKCHIP=y
> +CONFIG_SPL_RAM=y
> +CONFIG_BAUDRATE=1500000
> +CONFIG_DEBUG_UART_SHIFT=2
> +CONFIG_SYS_NS16550_MEM32=y
> +CONFIG_SYSRESET=y
> +CONFIG_USB=y
> +CONFIG_USB_XHCI_HCD=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_EHCI_GENERIC=y
> +CONFIG_USB_OHCI_HCD=y
> +CONFIG_USB_OHCI_GENERIC=y
> +CONFIG_USB_DWC3=y
> +CONFIG_USB_DWC3_GENERIC=y
> +CONFIG_ERRNO_STR=y
> +CONFIG_EFI_VAR_BUF_SIZE=16384
> diff --git a/doc/board/rockchip/rockchip.rst b/doc/board/rockchip/rockchip.rst
> index 49a0c5797a..31aeb85676 100644
> --- a/doc/board/rockchip/rockchip.rst
> +++ b/doc/board/rockchip/rockchip.rst
> @@ -95,6 +95,7 @@ List of mainline supported Rockchip boards:
>   
>   * rk3568
>        - Rockchip Evb-RK3568 (evb-rk3568)
> +     - EmbedFire Lubancat 2 (lubancat-2-rk3568_defconfig)
>        - Hardkernel ODROID-M1 (odroid-m1-rk3568)
>        - Pine64 Quartz64-A Board (quartz64-a-rk3566_defconfig)
>        - Pine64 Quartz64-B Board (quartz64-b-rk3566_defconfig)


More information about the U-Boot mailing list