[PATCH 1/2] mx6sabreauto: Convert to DM_PMIC
Fabio Estevam
festevam at denx.de
Thu Feb 16 11:08:48 CET 2023
The usage of DM_PMIC is preferred, so convert to it.
This also brings the benefit of causing a significant amount
of code removal.
Signed-off-by: Fabio Estevam <festevam at denx.de>
Reviewed-by: Peng Fan <peng.fan at nxp.com>
---
board/freescale/mx6sabreauto/mx6sabreauto.c | 109 +++-----------------
configs/mx6sabreauto_defconfig | 13 +--
include/configs/mx6sabreauto.h | 3 -
3 files changed, 19 insertions(+), 106 deletions(-)
diff --git a/board/freescale/mx6sabreauto/mx6sabreauto.c b/board/freescale/mx6sabreauto/mx6sabreauto.c
index 9155dcfbd0..0ae86f42df 100644
--- a/board/freescale/mx6sabreauto/mx6sabreauto.c
+++ b/board/freescale/mx6sabreauto/mx6sabreauto.c
@@ -19,14 +19,12 @@
#include <linux/errno.h>
#include <asm/gpio.h>
#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/mxc_i2c.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/mach-imx/spi.h>
#include <mmc.h>
#include <fsl_esdhc_imx.h>
#include <miiphy.h>
#include <asm/arch/sys_proto.h>
-#include <i2c.h>
#include <input.h>
#include <asm/arch/mxc_hdmi.h>
#include <asm/mach-imx/video.h>
@@ -49,23 +47,15 @@ DECLARE_GLOBAL_DATA_PTR;
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-
#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
PAD_CTL_SRE_FAST)
#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)
-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
-
#define WEIM_NOR_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-#define I2C_PMIC 1
-
int dram_init(void)
{
gd->ram_size = imx_ddr_size();
@@ -78,70 +68,6 @@ static iomux_v3_cfg_t const uart4_pads[] = {
IOMUX_PADS(PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
};
-
-/* I2C2 PMIC, iPod, Tuner, Codec, Touch, HDMI EDID, MIPI CSI2 card */
-static struct i2c_pads_info mx6q_i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6Q_PAD_EIM_EB2__I2C2_SCL | PC,
- .gpio_mode = MX6Q_PAD_EIM_EB2__GPIO2_IO30 | PC,
- .gp = IMX_GPIO_NR(2, 30)
- },
- .sda = {
- .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | PC,
- .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13 | PC,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
-static struct i2c_pads_info mx6dl_i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6DL_PAD_EIM_EB2__I2C2_SCL | PC,
- .gpio_mode = MX6DL_PAD_EIM_EB2__GPIO2_IO30 | PC,
- .gp = IMX_GPIO_NR(2, 30)
- },
- .sda = {
- .i2c_mode = MX6DL_PAD_KEY_ROW3__I2C2_SDA | PC,
- .gpio_mode = MX6DL_PAD_KEY_ROW3__GPIO4_IO13 | PC,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
-#ifndef CONFIG_SYS_FLASH_CFI
-/*
- * I2C3 MLB, Port Expanders (A, B, C), Video ADC, Light Sensor,
- * Compass Sensor, Accelerometer, Res Touch
- */
-static struct i2c_pads_info mx6q_i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6Q_PAD_GPIO_3__I2C3_SCL | PC,
- .gpio_mode = MX6Q_PAD_GPIO_3__GPIO1_IO03 | PC,
- .gp = IMX_GPIO_NR(1, 3)
- },
- .sda = {
- .i2c_mode = MX6Q_PAD_EIM_D18__I2C3_SDA | PC,
- .gpio_mode = MX6Q_PAD_EIM_D18__GPIO3_IO18 | PC,
- .gp = IMX_GPIO_NR(3, 18)
- }
-};
-
-static struct i2c_pads_info mx6dl_i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6DL_PAD_GPIO_3__I2C3_SCL | PC,
- .gpio_mode = MX6DL_PAD_GPIO_3__GPIO1_IO03 | PC,
- .gp = IMX_GPIO_NR(1, 3)
- },
- .sda = {
- .i2c_mode = MX6DL_PAD_EIM_D18__I2C3_SDA | PC,
- .gpio_mode = MX6DL_PAD_EIM_D18__GPIO3_IO18 | PC,
- .gp = IMX_GPIO_NR(3, 18)
- }
-};
-#endif
-
-static iomux_v3_cfg_t const i2c3_pads[] = {
- IOMUX_PADS(PAD_EIM_A24__GPIO5_IO04 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
static iomux_v3_cfg_t const port_exp[] = {
IOMUX_PADS(PAD_SD2_DAT0__GPIO1_IO15 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};
@@ -516,21 +442,10 @@ int board_init(void)
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
- /* I2C 2 and 3 setup - I2C 3 hw mux with EIM */
- if (is_mx6dq() || is_mx6dqp())
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info1);
- else
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1);
/* I2C 3 Steer */
gpio_request(IMX_GPIO_NR(5, 4), "steer logic");
gpio_direction_output(IMX_GPIO_NR(5, 4), 1);
- SETUP_IOMUX_PADS(i2c3_pads);
-#ifndef CONFIG_SYS_FLASH_CFI
- if (is_mx6dq() || is_mx6dqp())
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info2);
- else
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info2);
-#endif
+
gpio_request(IMX_GPIO_NR(1, 15), "expander en");
gpio_direction_output(IMX_GPIO_NR(1, 15), 1);
SETUP_IOMUX_PADS(port_exp);
@@ -554,22 +469,27 @@ int board_spi_cs_gpio(unsigned bus, unsigned cs)
int power_init_board(void)
{
- struct pmic *p;
- unsigned int value;
+ struct udevice *dev;
+ unsigned int value;
+ int ret;
+
+ ret = pmic_get("pfuze100 at 8", &dev);
+ if (ret == -ENODEV)
+ return 0;
+
+ if (ret != 0)
+ return ret;
- p = pfuze_common_init(I2C_PMIC);
- if (!p)
- return -ENODEV;
if (is_mx6dqp()) {
/* set SW2 staby volatage 0.975V*/
- pmic_reg_read(p, PFUZE100_SW2STBY, &value);
+ value = pmic_reg_read(dev, PFUZE100_SW2STBY);
value &= ~0x3f;
value |= 0x17;
- pmic_reg_write(p, PFUZE100_SW2STBY, value);
+ pmic_reg_write(dev, PFUZE100_SW2STBY, value);
}
- return pfuze_mode_init(p, APS_PFM);
+ return pfuze_mode_init(dev, APS_PFM);
}
#ifdef CONFIG_CMD_BMODE
@@ -979,7 +899,6 @@ void board_init_f(ulong dummy)
ccgr_init();
gpr_init();
- /* iomux and setup of i2c */
board_early_init_f();
/* setup GP timer */
diff --git a/configs/mx6sabreauto_defconfig b/configs/mx6sabreauto_defconfig
index 50f63c23b1..7d26c829ae 100644
--- a/configs/mx6sabreauto_defconfig
+++ b/configs/mx6sabreauto_defconfig
@@ -11,9 +11,6 @@ CONFIG_ENV_SIZE=0x2000
CONFIG_ENV_OFFSET=0xC0000
CONFIG_MX6QDL=y
CONFIG_TARGET_MX6SABREAUTO=y
-CONFIG_SYS_I2C_MXC_I2C1=y
-CONFIG_SYS_I2C_MXC_I2C2=y
-CONFIG_SYS_I2C_MXC_I2C3=y
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="imx6q-sabreauto"
CONFIG_SPL_TEXT_BASE=0x00908000
@@ -38,7 +35,6 @@ CONFIG_SYS_SPL_MALLOC=y
CONFIG_SPL_FIT_IMAGE_TINY=y
CONFIG_SPL_FS_EXT4=y
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot-dtb.img"
-CONFIG_SPL_I2C=y
CONFIG_SPL_USB_HOST=y
CONFIG_SPL_USB_GADGET=y
CONFIG_SPL_USB_SDP_SUPPORT=y
@@ -77,7 +73,6 @@ CONFIG_BOUNCE_BUFFER=y
CONFIG_DFU_MMC=y
CONFIG_DFU_SF=y
CONFIG_DM_I2C=y
-CONFIG_SPL_SYS_I2C_LEGACY=y
CONFIG_SYS_I2C_MXC=y
CONFIG_FSL_USDHC=y
CONFIG_MTD=y
@@ -94,10 +89,12 @@ CONFIG_RGMII=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
-CONFIG_POWER_LEGACY=y
-CONFIG_POWER_PFUZE100=y
+CONFIG_DM_PMIC=y
+CONFIG_DM_PMIC_PFUZE100=y
CONFIG_DM_REGULATOR=y
-CONFIG_POWER_I2C=y
+CONFIG_DM_REGULATOR_PFUZE100=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
CONFIG_DM_SERIAL=y
CONFIG_MXC_UART=y
CONFIG_SPI=y
diff --git a/include/configs/mx6sabreauto.h b/include/configs/mx6sabreauto.h
index 05ae2fce1f..91544c8a0e 100644
--- a/include/configs/mx6sabreauto.h
+++ b/include/configs/mx6sabreauto.h
@@ -35,7 +35,4 @@
/* DMA stuff, needed for GPMI/MXS NAND support */
-/* PMIC */
-#define CFG_POWER_PFUZE100_I2C_ADDR 0x08
-
#endif /* __MX6SABREAUTO_CONFIG_H */
--
2.25.1
More information about the U-Boot
mailing list