[PATCH v5 6/6] rockchip: add support for PX30 Ringneck SoM on Haikou Devkit
Quentin Schulz
foss+uboot at 0leil.net
Tue Jan 3 14:26:43 CET 2023
From: Quentin Schulz <quentin.schulz at theobroma-systems.com>
The PX30-µQ7 (Ringneck) is a system-on-module featuring the Rockchip
PX30 in a micro Qseven-compatible form-factor.
PX30-µQ7 features:
* CPU: quad-core Cortex-A35
* DRAM: 2GB dual-channel
* eMMC: onboard eMMC
* SD/MMC
* TI DP83825I 10/100Mbps PHY
* USB:
* USB2.0 dual role port
* 3x USB2.0 host via onboard USB2.0 hub
* Display: MIPI-DSI
* Camera: MIPI-CSI
* onboard 2.4GHz WiFi + Bluetooth module
* Companion Controller: on-board additional microcontroller
(STM32 Cortex-M0 or ATtiny):
* RTC
* fan controller
* CAN (only STM32)
The non-U-Boot DTS files are imported from Linux v6.2-rc2.
Cc: Quentin Schulz <foss+uboot at 0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz at theobroma-systems.com>
---
arch/arm/dts/px30-ringneck-haikou-u-boot.dtsi | 91 +++++
arch/arm/dts/px30-ringneck-haikou.dts | 232 +++++++++++++
arch/arm/dts/px30-ringneck.dtsi | 382 +++++++++++++++++++++
arch/arm/mach-rockchip/px30/Kconfig | 25 ++
board/theobroma-systems/ringneck_px30/Kconfig | 18 +
board/theobroma-systems/ringneck_px30/MAINTAINERS | 9 +
board/theobroma-systems/ringneck_px30/Makefile | 7 +
board/theobroma-systems/ringneck_px30/README | 69 ++++
.../ringneck_px30/ringneck-px30.c | 175 ++++++++++
configs/ringneck-px30_defconfig | 128 +++++++
doc/board/rockchip/rockchip.rst | 1 +
include/configs/ringneck_px30.h | 15 +
12 files changed, 1152 insertions(+)
diff --git a/arch/arm/dts/px30-ringneck-haikou-u-boot.dtsi b/arch/arm/dts/px30-ringneck-haikou-u-boot.dtsi
new file mode 100644
index 0000000000..e8a34c7c1e
--- /dev/null
+++ b/arch/arm/dts/px30-ringneck-haikou-u-boot.dtsi
@@ -0,0 +1,91 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "px30-u-boot.dtsi"
+
+/ {
+ config {
+ u-boot,mmc-env-offset = <0x5000>; /* @ 20KB */
+ u-boot,efi-partition-entries-offset = <0x200000>; /* 2MB */
+ u-boot,boot-led = "module_led";
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ u-boot,spl-boot-order = "same-as-spl", &emmc, &sdmmc;
+ };
+};
+
+&binman {
+ simple-bin {
+ blob {
+ offset = <((CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR - 64) * 512)>;
+ };
+ };
+};
+
+&emmc_clk {
+ u-boot,dm-pre-reloc;
+};
+
+&emmc_cmd {
+ u-boot,dm-pre-reloc;
+};
+
+&emmc_bus8 {
+ u-boot,dm-pre-reloc;
+};
+
+&gpio0 {
+ u-boot,dm-pre-reloc;
+};
+
+&gpio1 {
+ u-boot,dm-pre-reloc;
+};
+
+&gpio2 {
+ u-boot,dm-pre-reloc;
+
+ /*
+ * The Qseven BIOS_DISABLE signal on the PX30-µQ7 keeps the on-module
+ * eMMC powered-down initially (in fact it keeps the reset signal
+ * asserted). BIOS_DISABLE_OVERRIDE pin allows to re-enable eMMC after
+ * the SPL has been booted from SD Card.
+ */
+ bios-disable-override-hog {
+ u-boot,dm-pre-reloc;
+ };
+};
+
+&pinctrl {
+ u-boot,dm-pre-reloc;
+};
+
+&pcfg_pull_none_8ma {
+ u-boot,dm-pre-reloc;
+};
+
+&pcfg_pull_up_8ma {
+ u-boot,dm-pre-reloc;
+};
+
+&sdmmc_bus4 {
+ u-boot,dm-pre-reloc;
+};
+
+&sdmmc_clk {
+ u-boot,dm-pre-reloc;
+};
+
+&sdmmc_cmd {
+ u-boot,dm-pre-reloc;
+};
+
+&sdmmc_det {
+ u-boot,dm-pre-reloc;
+};
+
+&uart0 {
+ clock-frequency = <24000000>;
+ u-boot,dm-pre-reloc;
+};
diff --git a/arch/arm/dts/px30-ringneck-haikou.dts b/arch/arm/dts/px30-ringneck-haikou.dts
new file mode 100644
index 0000000000..08a3ad3e7a
--- /dev/null
+++ b/arch/arm/dts/px30-ringneck-haikou.dts
@@ -0,0 +1,232 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Theobroma Systems Design und Consulting GmbH
+ */
+
+/dts-v1/;
+#include "px30-ringneck.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "Theobroma Systems PX30-uQ7 SoM on Haikou devkit";
+ compatible = "tsd,px30-ringneck-haikou", "rockchip,px30";
+
+ aliases {
+ mmc2 = &sdmmc;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&haikou_keys_pin>;
+ pinctrl-names = "default";
+
+ button-batlow-n {
+ label = "BATLOW#";
+ linux,code = <KEY_BATTERY>;
+ gpios = <&gpio3 RK_PA7 GPIO_ACTIVE_LOW>;
+ };
+
+ button-slp-btn-n {
+ label = "SLP_BTN#";
+ linux,code = <KEY_SLEEP>;
+ gpios = <&gpio1 RK_PB7 GPIO_ACTIVE_LOW>;
+ };
+
+ button-wake-n {
+ label = "WAKE#";
+ linux,code = <KEY_WAKEUP>;
+ gpios = <&gpio1 RK_PB6 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+
+ switch-lid-btn-n {
+ label = "LID_BTN#";
+ linux,code = <SW_LID>;
+ linux,input-type = <EV_SW>;
+ gpios = <&gpio3 RK_PA6 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ pinctrl-0 = <&module_led_pin>, <&sd_card_led_pin>;
+
+ sd_card_led: led-1 {
+ gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc2";
+ function = LED_FUNCTION_SD;
+ color = <LED_COLOR_ID_BLUE>;
+ };
+ };
+
+ i2s0-sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "Haikou,I2S-codec";
+ simple-audio-card,mclk-fs = <512>;
+
+ simple-audio-card,codec {
+ clocks = <&sgtl5000_clk>;
+ sound-dai = <&sgtl5000>;
+ };
+
+ simple-audio-card,cpu {
+ bitclock-master;
+ frame-master;
+ sound-dai = <&i2s0_8ch>;
+ };
+ };
+
+ sgtl5000_clk: sgtl5000-oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>;
+ };
+
+ dc_12v: dc-12v-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "dc_12v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc3v3_baseboard: vcc3v3-baseboard-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_baseboard";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vcc5v0_baseboard: vcc5v0-baseboard-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_baseboard";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vdda_codec: vdda-codec-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vdda_codec";
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_baseboard>;
+ };
+
+ vddd_codec: vddd-codec-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vddd_codec";
+ regulator-boot-on;
+ regulator-min-microvolt = <1600000>;
+ regulator-max-microvolt = <1600000>;
+ vin-supply = <&vcc5v0_baseboard>;
+ };
+};
+
+&i2c2 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ sgtl5000: codec at a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ clocks = <&sgtl5000_clk>;
+ #sound-dai-cells = <0>;
+ VDDA-supply = <&vdda_codec>;
+ VDDIO-supply = <&vcc3v3_baseboard>;
+ VDDD-supply = <&vddd_codec>;
+ };
+};
+
+&i2c3 {
+ eeprom at 50 {
+ reg = <0x50>;
+ compatible = "atmel,24c01";
+ pagesize = <8>;
+ size = <128>;
+ vcc-supply = <&vcc3v3_baseboard>;
+ };
+};
+
+&i2s0_8ch {
+ status = "okay";
+};
+
+&gmac {
+ status = "okay";
+};
+
+&pinctrl {
+ haikou {
+ haikou_keys_pin: haikou-keys-pin {
+ rockchip,pins =
+ /* WAKE# */
+ <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* SLP_BTN# */
+ <1 RK_PB7 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* LID_BTN */
+ <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* BATLOW# */
+ <3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* BIOS_DISABLE# */
+ <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ leds {
+ sd_card_led_pin: sd-card-led-pin {
+ rockchip,pins =
+ <3 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&sdmmc {
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio0 RK_PA3 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ vmmc-supply = <&vcc3v3_baseboard>;
+ status = "okay";
+};
+
+&spi1 {
+ status = "okay";
+};
+
+&u2phy_otg {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-0 = <&uart5_xfer>;
+ status = "okay";
+};
+
+&usb20_otg {
+ status = "okay";
+};
diff --git a/arch/arm/dts/px30-ringneck.dtsi b/arch/arm/dts/px30-ringneck.dtsi
new file mode 100644
index 0000000000..1239775583
--- /dev/null
+++ b/arch/arm/dts/px30-ringneck.dtsi
@@ -0,0 +1,382 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Theobroma Systems Design und Consulting GmbH
+ */
+
+/dts-v1/;
+#include "px30.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+ aliases {
+ mmc0 = &emmc;
+ mmc1 = &sdio;
+ rtc0 = &rtc_twi;
+ rtc1 = &rk809;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ pinctrl-0 = <&emmc_reset>;
+ pinctrl-names = "default";
+ reset-gpios = <&gpio1 RK_PB3 GPIO_ACTIVE_HIGH>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&module_led_pin>;
+ status = "okay";
+
+ module_led: led-0 {
+ gpios = <&gpio1 RK_PB0 GPIO_ACTIVE_HIGH>;
+ function = LED_FUNCTION_HEARTBEAT;
+ linux,default-trigger = "heartbeat";
+ color = <LED_COLOR_ID_AMBER>;
+ };
+ };
+
+ vcc5v0_sys: vccsys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ supports-emmc;
+ mmc-pwrseq = <&emmc_pwrseq>;
+ non-removable;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&vcc_emmc>;
+
+ status = "okay";
+};
+
+/* On-module TI DP83825I PHY but no connector, enable in carrierboard */
+&gmac {
+ snps,reset-gpio = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 50000 50000>;
+ phy-supply = <&vcc_3v3>;
+ clock_in_out = "output";
+};
+
+&gpio2 {
+ /*
+ * The Qseven BIOS_DISABLE signal on the PX30-µQ7 keeps the on-module
+ * eMMC powered-down initially (in fact it keeps the reset signal
+ * asserted). BIOS_DISABLE_OVERRIDE pin allows to re-enable eMMC after
+ * the SPL has been booted from SD Card.
+ */
+ bios-disable-override-hog {
+ gpios = <RK_PB5 GPIO_ACTIVE_LOW>;
+ output-high;
+ line-name = "bios_disable_override";
+ gpio-hog;
+ };
+
+ /*
+ * The BIOS_DISABLE hog is a feedback pin for the actual status of the
+ * signal, ignoring the BIOS_DISABLE_OVERRIDE logic. This usually
+ * represents the state of a switch on the baseboard.
+ */
+ bios-disable-n-hog {
+ gpios = <RK_PC2 GPIO_ACTIVE_LOW>;
+ line-name = "bios_disable";
+ input;
+ gpio-hog;
+ };
+};
+
+&gpu {
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ rk809: pmic at 20 {
+ compatible = "rockchip,rk809";
+ reg = <0x20>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&pmic_int>;
+ pinctrl-names = "default";
+ #clock-cells = <0>;
+ clock-output-names = "xin32k";
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc5v0_sys>;
+ vcc2-supply = <&vcc5v0_sys>;
+ vcc3-supply = <&vcc5v0_sys>;
+ vcc4-supply = <&vcc5v0_sys>;
+ vcc5-supply = <&vcc_3v3>;
+ vcc6-supply = <&vcc_3v3>;
+ vcc7-supply = <&vcc_3v3>;
+ vcc9-supply = <&vcc5v0_sys>;
+
+ regulators {
+ vdd_log: DCDC_REG1 {
+ regulator-name = "vdd_log";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <950000>;
+ };
+ };
+
+ vdd_arm: DCDC_REG2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <6001>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <950000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_3v0_1v8: vcc_emmc: DCDC_REG4 {
+ regulator-name = "vcc_3v0_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3000000>;
+ };
+ };
+
+ vcc_3v3: DCDC_REG5 {
+ regulator-name = "vcc_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_1v8: LDO_REG2 {
+ regulator-name = "vcc_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_1v0: LDO_REG3 {
+ regulator-name = "vcc_1v0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vccio_sd: LDO_REG5 {
+ regulator-name = "vccio_sd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_lcd: LDO_REG7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "vcc_lcd";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vcc_1v8_lcd: LDO_REG8 {
+ regulator-name = "vcc_1v8_lcd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca_1v8: LDO_REG9 {
+ regulator-name = "vcca_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+
+ /* SE05x is limited to Fast Mode */
+ clock-frequency = <400000>;
+
+ fan: fan at 18 {
+ compatible = "ti,amc6821";
+ reg = <0x18>;
+ #cooling-cells = <2>;
+ };
+
+ rtc_twi: rtc at 6f {
+ compatible = "isil,isl1208";
+ reg = <0x6f>;
+ };
+};
+
+&i2c3 {
+ status = "okay";
+};
+
+&i2s0_8ch {
+ rockchip,trcm-sync-tx-only;
+
+ pinctrl-0 = <&i2s0_8ch_sclktx &i2s0_8ch_lrcktx
+ &i2s0_8ch_sdo0 &i2s0_8ch_sdi0>;
+};
+
+&io_domains {
+ vccio1-supply = <&vcc_3v3>;
+ vccio2-supply = <&vccio_sd>;
+ vccio3-supply = <&vcc_3v3>;
+ vccio4-supply = <&vcc_3v3>;
+ vccio5-supply = <&vcc_3v3>;
+ vccio6-supply = <&vcc_emmc>;
+ vccio-oscgpi-supply = <&vcc_3v3>;
+
+ status = "okay";
+};
+
+&pinctrl {
+ emmc {
+ emmc_reset: emmc-reset {
+ rockchip,pins = <1 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ leds {
+ module_led_pin: module-led-pin {
+ rockchip,pins = <1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int: pmic-int {
+ rockchip,pins =
+ <0 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&saradc {
+ vref-supply = <&vcc_1v8>;
+ status = "okay";
+};
+
+&sdmmc {
+ vqmmc-supply = <&vccio_sd>;
+};
+
+&tsadc {
+ status = "okay";
+};
+
+&u2phy {
+ status = "okay";
+};
+
+&u2phy_host {
+ status = "okay";
+};
+
+/* Mule UCAN */
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
diff --git a/arch/arm/mach-rockchip/px30/Kconfig b/arch/arm/mach-rockchip/px30/Kconfig
index 28639c0041..41893920cb 100644
--- a/arch/arm/mach-rockchip/px30/Kconfig
+++ b/arch/arm/mach-rockchip/px30/Kconfig
@@ -35,6 +35,30 @@ config TARGET_PX30_CORE
* PX30.Core needs to mount on top of C.TOUCH 2.0 carrier with pluged
10.1" OF for creating complete PX30.Core C.TOUCH 2.0 10.1" Open Frame.
+config TARGET_RINGNECK_PX30
+ bool "Theobroma Systems PX30-µQ7 (Ringneck)"
+ help
+ The PX30-uQ7 (Ringneck) SoM is a µQseven-compatible (40mmx70mm,
+ MXM-230 connector) system-on-module from Theobroma Systems[1],
+ featuring the Rockchip PX30.
+
+ It provides the following feature set:
+ * up to 4GB DDR4
+ * up to 128GB on-module eMMC (with 8-bit 1.8V interface)
+ * SD card (on a baseboard) via edge connector
+ * Fast Ethernet with on-module TI DP83825I PHY
+ * MIPI-DSI/LVDS
+ * MIPI-CSI
+ * USB
+ - 1x USB 2.0 dual-role
+ - 3x USB 2.0 host
+ * on-module companion controller (STM32 Cortex-M0 or ATtiny), implementing:
+ - low-power RTC functionality (ISL1208 emulation)
+ - fan controller (AMC6821 emulation)
+ - USB<->CAN bridge controller (STM32 only)
+ * on-module Espressif ESP32 for Bluetooth + 2.4GHz WiFi
+ * on-module NXP SE05x Secure Element
+
config ROCKCHIP_BOOT_MODE_REG
default 0xff010200
@@ -71,5 +95,6 @@ config DEBUG_UART_CHANNEL
source "board/engicam/px30_core/Kconfig"
source "board/hardkernel/odroid_go2/Kconfig"
source "board/rockchip/evb_px30/Kconfig"
+source "board/theobroma-systems/ringneck_px30/Kconfig"
endif
diff --git a/board/theobroma-systems/ringneck_px30/Kconfig b/board/theobroma-systems/ringneck_px30/Kconfig
new file mode 100644
index 0000000000..24d94807db
--- /dev/null
+++ b/board/theobroma-systems/ringneck_px30/Kconfig
@@ -0,0 +1,18 @@
+if TARGET_RINGNECK_PX30
+
+config SYS_BOARD
+ default "ringneck_px30"
+
+config SYS_VENDOR
+ default "theobroma-systems"
+
+config SYS_CONFIG_NAME
+ default "ringneck_px30"
+
+config BOARD_SPECIFIC_OPTIONS # dummy
+ def_bool y
+
+config ENV_SIZE
+ default 0x3000
+
+endif
diff --git a/board/theobroma-systems/ringneck_px30/MAINTAINERS b/board/theobroma-systems/ringneck_px30/MAINTAINERS
new file mode 100644
index 0000000000..d764e26066
--- /dev/null
+++ b/board/theobroma-systems/ringneck_px30/MAINTAINERS
@@ -0,0 +1,9 @@
+RINGNECK-PX30
+M: Quentin Schulz <quentin.schulz at theobroma-systems.com>
+M: Klaus Goger <klaus.goger at theobroma-systems.com>
+S: Maintained
+F: board/theobroma-systems/ringneck_px30
+F: include/configs/ringneck_px30.h
+F: arch/arm/dts/px30-ringneck*
+F: configs/ringneck-px30_defconfig
+W: https://www.theobroma-systems.com/px30-uq7#tech-spec
diff --git a/board/theobroma-systems/ringneck_px30/Makefile b/board/theobroma-systems/ringneck_px30/Makefile
new file mode 100644
index 0000000000..31ada1a694
--- /dev/null
+++ b/board/theobroma-systems/ringneck_px30/Makefile
@@ -0,0 +1,7 @@
+#
+# (C) Copyright 2022 Theobroma Systems Design und Consulting GmbH
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += ringneck-px30.o
diff --git a/board/theobroma-systems/ringneck_px30/README b/board/theobroma-systems/ringneck_px30/README
new file mode 100644
index 0000000000..e756b3a8ff
--- /dev/null
+++ b/board/theobroma-systems/ringneck_px30/README
@@ -0,0 +1,69 @@
+Introduction
+============
+
+The PX30-uQ7 (Ringneck) SoM is a µQseven-compatible (40mmx70mm, MXM-230
+connector) system-on-module from Theobroma Systems[1], featuring the
+Rockchip PX30.
+
+It provides the following feature set:
+ * up to 4GB DDR4
+ * up to 128GB on-module eMMC (with 8-bit 1.8V interface)
+ * SD card (on a baseboard) via edge connector
+ * Fast Ethernet with on-module TI DP83825I PHY
+ * MIPI-DSI/LVDS
+ * MIPI-CSI
+ * USB
+ - 1x USB 2.0 dual-role
+ - 3x USB 2.0 host
+ * on-module companion controller (STM32 Cortex-M0 or ATtiny), implementing:
+ - low-power RTC functionality (ISL1208 emulation)
+ - fan controller (AMC6821 emulation)
+ - USB<->CAN bridge controller (STM32 only)
+ * on-module Espressif ESP32 for Bluetooth + 2.4GHz WiFi
+ * on-module NXP SE05x Secure Element
+
+Here is the step-by-step to boot to U-Boot on px30.
+
+Get the Source and build ATF binary
+===================================
+
+ > git clone https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git
+
+Compile the ATF
+===============
+
+ > cd trusted-firmware-a
+ > make CROSS_COMPILE=aarch64-linux-gnu- PLAT=px30 bl31
+ > cp build/px30/release/bl31/bl31.elf ../u-boot/bl31.elf
+
+Compile the U-Boot
+==================
+
+ > cd ../u-boot
+ > make CROSS_COMPILE=aarch64-linux-gnu- ringneck-px30_defconfig all
+
+Flash the image
+===============
+
+Copy u-boot-rockchip.bin to offset 32k for SD/eMMC.
+
+SD-Card
+-------
+
+ > dd if=u-boot-rockchip.bin of=/dev/sdb seek=64
+
+eMMC
+----
+
+rkdeveloptool allows to flash the on-board eMMC via the USB OTG interface with
+help of the Rockchip loader binary.
+
+ > git clone https://github.com/rockchip-linux/rkdeveloptool
+ > cd rkdeveloptool
+ > autoreconf -i && ./configure && make
+ > git clone https://github.com/rockchip-linux/rkbin.git
+ > cd rkbin
+ > ./tools/boot_merger RKBOOT/PX30MINIALL.ini
+ > cd ..
+ > ./rkdeveloptool db rkbin/px30_loader_v1.16.131.bin
+ > ./rkdeveloptool wl 64 ../u-boot-rockchip.bin
diff --git a/board/theobroma-systems/ringneck_px30/ringneck-px30.c b/board/theobroma-systems/ringneck_px30/ringneck-px30.c
new file mode 100644
index 0000000000..47d1a40ef7
--- /dev/null
+++ b/board/theobroma-systems/ringneck_px30/ringneck-px30.c
@@ -0,0 +1,175 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2022 Theobroma Systems Design und Consulting GmbH
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <env.h>
+#include <env_internal.h>
+#include <init.h>
+#include <log.h>
+#include <misc.h>
+#include <spl.h>
+#include <syscon.h>
+#include <u-boot/crc.h>
+#include <usb.h>
+#include <dm/pinctrl.h>
+#include <dm/uclass-internal.h>
+#include <asm/io.h>
+#include <asm/setup.h>
+#include <asm/arch-rockchip/clock.h>
+#include <asm/arch-rockchip/hardware.h>
+#include <asm/arch-rockchip/periph.h>
+#include <asm/arch-rockchip/misc.h>
+#include <power/regulator.h>
+#include <u-boot/sha256.h>
+
+/*
+ * Swap mmc0 and mmc1 in boot_targets if booted from SD-Card.
+ *
+ * If bootsource is uSD-card we can assume that we want to use the
+ * SD-Card instead of the eMMC as first boot_target for distroboot.
+ * We only want to swap the defaults and not any custom environment a
+ * user has set. We exit early if a changed boot_targets environment
+ * is detected.
+ */
+static int setup_boottargets(void)
+{
+ const char *boot_device =
+ ofnode_read_chosen_string("u-boot,spl-boot-device");
+ char *env_default, *env;
+
+ if (!boot_device) {
+ debug("%s: /chosen/u-boot,spl-boot-device not set\n",
+ __func__);
+ return -1;
+ }
+ debug("%s: booted from %s\n", __func__, boot_device);
+
+ env_default = env_get_default("boot_targets");
+ env = env_get("boot_targets");
+ if (!env) {
+ debug("%s: boot_targets does not exist\n", __func__);
+ return -1;
+ }
+ debug("%s: boot_targets current: %s - default: %s\n",
+ __func__, env, env_default);
+
+ if (strcmp(env_default, env) != 0) {
+ debug("%s: boot_targets not default, don't change it\n",
+ __func__);
+ return 0;
+ }
+
+ /*
+ * Make the default boot medium between SD Card and eMMC, the one that
+ * was used to load U-Boot proper.
+ */
+ bool sd_booted = !strcmp(boot_device, "/mmc at ff370000");
+ char *mmc0, *mmc1;
+
+ debug("%s: booted from %s\n", __func__,
+ sd_booted ? "SD-Card" : "eMMC");
+ mmc0 = strstr(env, "mmc0");
+ mmc1 = strstr(env, "mmc1");
+
+ if (!mmc0 || !mmc1) {
+ debug("%s: only one mmc boot_target found\n", __func__);
+ return -1;
+ }
+
+ /*
+ * If mmc0 comes first in the boot order and U-Boot proper was
+ * loaded from mmc1, swap mmc0 and mmc1 in the list.
+ * If mmc1 comes first in the boot order and U-Boot proper was
+ * loaded from mmc0, swap mmc0 and mmc1 in the list.
+ */
+ if ((mmc0 < mmc1 && sd_booted) ||
+ (mmc0 > mmc1 && !sd_booted)) {
+ mmc0[3] = '1';
+ mmc1[3] = '0';
+ debug("%s: set boot_targets to: %s\n", __func__, env);
+ env_set("boot_targets", env);
+ }
+
+ return 0;
+}
+
+int mmc_get_env_dev(void)
+{
+ const char *boot_device =
+ ofnode_read_chosen_string("u-boot,spl-boot-device");
+
+ if (!boot_device) {
+ debug("%s: /chosen/u-boot,spl-boot-device not set\n",
+ __func__);
+ return CONFIG_SYS_MMC_ENV_DEV;
+ }
+
+ debug("%s: booted from %s\n", __func__, boot_device);
+
+ if (!strcmp(boot_device, "/mmc at ff370000"))
+ return 1;
+
+ if (!strcmp(boot_device, "/mmc at ff390000"))
+ return 0;
+
+ return CONFIG_SYS_MMC_ENV_DEV;
+}
+
+#if !IS_ENABLED(CONFIG_ENV_IS_NOWHERE)
+#error Please enable CONFIG_ENV_IS_NOWHERE
+#endif
+
+enum env_location arch_env_get_location(enum env_operation op, int prio)
+{
+ const char *boot_device =
+ ofnode_read_chosen_string("u-boot,spl-boot-device");
+
+ if (prio > 0)
+ return ENVL_UNKNOWN;
+
+ if (!boot_device) {
+ debug("%s: /chosen/u-boot,spl-boot-device not set\n",
+ __func__);
+ return ENVL_NOWHERE;
+ }
+
+ debug("%s: booted from %s\n", __func__, boot_device);
+
+ if (IS_ENABLED(CONFIG_ENV_IS_IN_MMC) &&
+ (!strcmp(boot_device, "/mmc at ff370000") ||
+ !strcmp(boot_device, "/mmc at ff390000")))
+ return ENVL_MMC;
+
+ printf("%s: No environment available: booted from %s but U-Boot "
+ "config does not allow loading environment from it.",
+ __func__, boot_device);
+
+ return ENVL_NOWHERE;
+}
+
+int misc_init_r(void)
+{
+ const u32 cpuid_offset = 0x7;
+ const u32 cpuid_length = 0x10;
+ u8 cpuid[cpuid_length];
+ int ret;
+
+ ret = rockchip_cpuid_from_efuse(cpuid_offset, cpuid_length, cpuid);
+ if (ret)
+ return ret;
+
+ ret = rockchip_cpuid_set(cpuid, cpuid_length);
+ if (ret)
+ return ret;
+
+ ret = rockchip_setup_macaddr();
+ if (ret)
+ return ret;
+
+ setup_boottargets();
+
+ return 0;
+}
diff --git a/configs/ringneck-px30_defconfig b/configs/ringneck-px30_defconfig
new file mode 100644
index 0000000000..7ad281a3fe
--- /dev/null
+++ b/configs/ringneck-px30_defconfig
@@ -0,0 +1,128 @@
+CONFIG_ARM=y
+CONFIG_SKIP_LOWLEVEL_INIT=y
+CONFIG_COUNTER_FREQUENCY=24000000
+CONFIG_ARCH_ROCKCHIP=y
+CONFIG_TEXT_BASE=0x00200000
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_SPL_GPIO=y
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_DEFAULT_DEVICE_TREE="px30-ringneck-haikou"
+CONFIG_SPL_TEXT_BASE=0x00000000
+CONFIG_ROCKCHIP_PX30=y
+CONFIG_TARGET_RINGNECK_PX30=y
+CONFIG_TPL_LIBGENERIC_SUPPORT=y
+CONFIG_SPL_DRIVERS_MISC=y
+CONFIG_SPL_STACK_R_ADDR=0x600000
+CONFIG_DEBUG_UART_BASE=0xFF030000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_SYS_LOAD_ADDR=0x800800
+CONFIG_TPL_MAX_SIZE=0x20000
+CONFIG_DEBUG_UART=y
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x400000
+CONFIG_TPL_SYS_MALLOC_F_LEN=0x600
+# CONFIG_ANDROID_BOOT_IMAGE is not set
+CONFIG_FIT=y
+CONFIG_FIT_VERBOSE=y
+CONFIG_SPL_LOAD_FIT=y
+CONFIG_DEFAULT_FDT_FILE="rockchip/px30-ringneck-haikou.dtb"
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_MISC_INIT_R=y
+CONFIG_SPL_MAX_SIZE=0x20000
+CONFIG_SPL_PAD_TO=0x0
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x4000000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+CONFIG_SPL_BOOTROM_SUPPORT=y
+# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK=0x400000
+CONFIG_SPL_STACK_R=y
+CONFIG_SYS_SPL_MALLOC=y
+CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x200
+CONFIG_SPL_ATF=y
+# CONFIG_TPL_FRAMEWORK is not set
+# CONFIG_CMD_BOOTD is not set
+# CONFIG_CMD_ELF is not set
+# CONFIG_CMD_IMI is not set
+# CONFIG_CMD_XIMG is not set
+# CONFIG_CMD_LZMADEC is not set
+# CONFIG_CMD_UNZIP is not set
+CONFIG_CMD_GPT=y
+# CONFIG_CMD_LOADB is not set
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+# CONFIG_CMD_ITEST is not set
+# CONFIG_CMD_SETEXPR is not set
+# CONFIG_CMD_SLEEP is not set
+# CONFIG_SPL_DOS_PARTITION is not set
+# CONFIG_ISO_PARTITION is not set
+CONFIG_EFI_PARTITION_ENTRIES_NUMBERS=64
+CONFIG_SPL_OF_CONTROL=y
+CONFIG_OF_LIVE=y
+CONFIG_OF_SPL_REMOVE_PROPS="interrupt-parent assigned-clocks assigned-clock-rates assigned-clock-parents"
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_NOWHERE=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SPL_DM_SEQ_ALIAS=y
+CONFIG_REGMAP=y
+CONFIG_SPL_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_SPL_SYSCON=y
+CONFIG_BUTTON=y
+CONFIG_BUTTON_GPIO=y
+CONFIG_CLK=y
+CONFIG_SPL_CLK=y
+CONFIG_FASTBOOT_BUF_ADDR=0x800800
+CONFIG_FASTBOOT_BUF_SIZE=0x04000000
+CONFIG_GPIO_HOG=y
+CONFIG_SPL_GPIO_HOG=y
+CONFIG_ROCKCHIP_GPIO=y
+CONFIG_SYS_I2C_ROCKCHIP=y
+CONFIG_MISC=y
+CONFIG_ROCKCHIP_OTP=y
+CONFIG_SUPPORT_EMMC_RPMB=y
+CONFIG_MMC_DW=y
+CONFIG_MMC_DW_ROCKCHIP=y
+CONFIG_PHY_TI_GENERIC=y
+CONFIG_PHY_GIGE=y
+CONFIG_ETH_DESIGNWARE=y
+CONFIG_GMAC_ROCKCHIP=y
+CONFIG_PINCTRL=y
+CONFIG_SPL_PINCTRL=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_RK8XX=y
+CONFIG_REGULATOR_PWM=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_REGULATOR_RK8XX=y
+CONFIG_PWM_ROCKCHIP=y
+CONFIG_RAM=y
+CONFIG_SPL_RAM=y
+CONFIG_TPL_RAM=y
+CONFIG_ROCKCHIP_SDRAM_COMMON=y
+CONFIG_RAM_PX30_DDR4=y
+CONFIG_DM_RESET=y
+CONFIG_DM_RNG=y
+CONFIG_RNG_ROCKCHIP=y
+# CONFIG_SPECIFY_CONSOLE_INDEX is not set
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_SOUND=y
+CONFIG_SYSRESET=y
+CONFIG_DM_THERMAL=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_GENERIC=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_SPL_TINY_MEMSET=y
+CONFIG_TPL_TINY_MEMSET=y
+CONFIG_LZO=y
+CONFIG_ERRNO_STR=y
+# CONFIG_EFI_LOADER is not set
diff --git a/doc/board/rockchip/rockchip.rst b/doc/board/rockchip/rockchip.rst
index 4ca7b00b1f..92a5c27306 100644
--- a/doc/board/rockchip/rockchip.rst
+++ b/doc/board/rockchip/rockchip.rst
@@ -27,6 +27,7 @@ List of mainline supported Rockchip boards:
- Engicam PX30.Core C.TOUCH 2.0 10.1 (px30-core-ctouch2-of10-px30)
- Engicam PX30.Core EDIMM2.2 Starter Kit (px30-core-edimm2.2-px30)
- Firefly Core-PX30-JD4 (firefly-px30)
+ - Theobroma Systems PX30-µQ7 SoM - Ringneck (ringneck-px30)
* rk3036
- Rockchip Evb-RK3036 (evb-rk3036)
- Kylin (kylin_rk3036)
diff --git a/include/configs/ringneck_px30.h b/include/configs/ringneck_px30.h
new file mode 100644
index 0000000000..c63c935e9a
--- /dev/null
+++ b/include/configs/ringneck_px30.h
@@ -0,0 +1,15 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (C) Copyright 2022 Theobroma Systems Design und Consulting GmbH
+ */
+
+#ifndef __RINGNECK_PX30_H
+#define __RINGNECK_PX30_H
+
+#include <configs/px30_common.h>
+
+#define ROCKCHIP_DEVICE_SETTINGS \
+ "stdout=serial,vidconsole\0" \
+ "stderr=serial,vidconsole\0"
+
+#endif
--
b4 0.10.1
More information about the U-Boot
mailing list