[PATCH 5/5] ARM: dts: at91: sam9x60-curiosity: Add raw NAND flash

Alexander Dahl post at lespocky.de
Wed Jul 5 22:17:01 CEST 2023


From: Alexander Dahl <ada at thorsis.com>

Basically the same as on sam9x60-ek.  Same as in Linux.  NAND flash is
correctly detected when booting into U-Boot:

    U-Boot 2023.07-rc6-00005-g12719f75dc-dirty (Jul 05 2023 - 13:06:35 +0000)

    CPU:   SAM9X60 128MiB DDR2 SiP
    Crystal frequency:       24 MHz
    CPU clock        :      600 MHz
    Master clock     :      200 MHz

    Model: Microchip SAM9X60 Curiosity
    DRAM:  128 MiB
    Core:  145 devices, 22 uclasses, devicetree: separate
    NAND:  512 MiB
    MMC:   sdhci-host at 80000000: 0, sdhci-host at 90000000: 1
    Loading Environment from FAT... Unable to read "uboot.env" from mmc0:1...
    In:    serial
    Out:   serial
    Err:   serial
    Net:   eth0: ethernet at f802c000
    Hit any key to stop autoboot:  0

Signed-off-by: Alexander Dahl <ada at thorsis.com>
---
 arch/arm/dts/at91-sam9x60_curiosity.dts | 103 ++++++++++++++++++++++++
 1 file changed, 103 insertions(+)

diff --git a/arch/arm/dts/at91-sam9x60_curiosity.dts b/arch/arm/dts/at91-sam9x60_curiosity.dts
index fb59405b24..2547b4527c 100644
--- a/arch/arm/dts/at91-sam9x60_curiosity.dts
+++ b/arch/arm/dts/at91-sam9x60_curiosity.dts
@@ -46,6 +46,71 @@
 	};
 };
 
+&ebi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ebi_addr_nand &pinctrl_ebi_data_0_7>;
+	status = "okay";
+
+	nand_controller: nand-controller {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_nand_oe_we &pinctrl_nand_cs &pinctrl_nand_rb>;
+		status = "okay";
+
+		nand at 3 {
+			reg = <0x3 0x0 0x800000>;
+			rb-gpios = <&pioD 5 GPIO_ACTIVE_HIGH>;
+			cs-gpios = <&pioD 4 GPIO_ACTIVE_HIGH>;
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			nand-ecc-strength = <8>;
+			nand-ecc-step-size = <512>;
+			nand-on-flash-bbt;
+			label = "atmel_nand";
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				at91bootstrap at 0 {
+					label = "at91bootstrap";
+					reg = <0x0 0x40000>;
+				};
+
+				uboot at 40000 {
+					label = "u-boot";
+					reg = <0x40000 0xc0000>;
+				};
+
+				ubootenvred at 100000 {
+					label = "U-Boot Env Redundant";
+					reg = <0x100000 0x40000>;
+				};
+
+				ubootenv at 140000 {
+					label = "U-Boot Env";
+					reg = <0x140000 0x40000>;
+				};
+
+				dtb at 180000 {
+					label = "device tree";
+					reg = <0x180000 0x80000>;
+				};
+
+				kernel at 200000 {
+					label = "kernel";
+					reg = <0x200000 0x600000>;
+				};
+
+				rootfs at 800000 {
+					label = "rootfs";
+					reg = <0x800000 0x1f800000>;
+				};
+			};
+		};
+	};
+};
+
 &flx0 {
 	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
 	status = "okay";
@@ -74,6 +139,26 @@
 };
 
 &pinctrl {
+	ebi {
+		pinctrl_ebi_data_0_7: ebi-data-lsb-0 {
+			atmel,pins =
+				<AT91_PIOD 6 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 7 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 8 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 9 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 10 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 11 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 12 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 13 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+		};
+
+		pinctrl_ebi_addr_nand: ebi-addr-0 {
+			atmel,pins =
+				<AT91_PIOD 2 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 3 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+		};
+	};
+
 	flexcom {
 		pinctrl_flx0: flx0_default {
 			atmel,pins =
@@ -82,6 +167,24 @@
 		};
 	};
 
+	nand {
+		pinctrl_nand_oe_we: nand-oe-we-0 {
+			atmel,pins =
+				<AT91_PIOD 0 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)
+				 AT91_PIOD 1 AT91_PERIPH_A (AT91_PINCTRL_NONE | AT91_PINCTRL_SLEWRATE_DIS)>;
+		};
+
+		pinctrl_nand_rb: nand-rb-0 {
+			atmel,pins =
+				<AT91_PIOD 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_nand_cs: nand-cs-0 {
+			atmel,pins =
+				<AT91_PIOD 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+		};
+	};
+
 	pinctrl_onewire_tm_default: onewire_tm_default {
 		atmel,pins =
 			<AT91_PIOD 14 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
-- 
2.30.2



More information about the U-Boot mailing list