[PATCH 3/3] arm: dts: k3-am62: Bump dtsi from linux v6.5-rc1
Nishanth Menon
nm at ti.com
Tue Jul 25 14:58:56 CEST 2023
Update the am62 and am625 device-trees from linux v6.3-rc5 This needed the followin
tweaks to the u-boot specific dtsi as well:
- Switch tick-timer to the main_timer as it's now defined in the main dtsi
- Secure proxies are defined in Soc dtsis
- Drop duplicate nodes - u-boot.dtsi is includes in r5-sk, no need for
either the definitions from main.dtsi OR duplication from u-boot.dtsi
- Add mdio pins to the cpsw3g pinctrl in u-boot dtsi. It moved to a subnode in the
linux dtsi that u-boot doesn't use/support
Cc: Francesco Dolcini <francesco at dolcini.it>
Cc: Sjoerd Simons <sjoerd at collabora.com>
Cc: Wadim Egorov <w.egorov at phytec.de>
Signed-off-by: Nishanth Menon <nm at ti.com>
---
I decided not to pick up changes from Roger and Maxime as they are'nt
regression fixes, instead the fixups can be done on top of the basic
sync.
arch/arm/dts/k3-am62-main.dtsi | 389 +++++++++++++++++++++++--
arch/arm/dts/k3-am62-mcu.dtsi | 66 +++++
arch/arm/dts/k3-am62-thermal.dtsi | 33 +++
arch/arm/dts/k3-am62-wakeup.dtsi | 33 ++-
arch/arm/dts/k3-am62.dtsi | 11 +-
arch/arm/dts/k3-am625-r5-sk.dts | 92 +-----
arch/arm/dts/k3-am625-sk-u-boot.dtsi | 24 +-
arch/arm/dts/k3-am625-sk.dts | 286 ++-----------------
arch/arm/dts/k3-am625.dtsi | 54 +++-
arch/arm/dts/k3-am62x-sk-common.dtsi | 412 +++++++++++++++++++++++++++
arch/arm/dts/k3-pinctrl.h | 53 ++++
11 files changed, 1065 insertions(+), 388 deletions(-)
create mode 100644 arch/arm/dts/k3-am62-thermal.dtsi
create mode 100644 arch/arm/dts/k3-am62x-sk-common.dtsi
create mode 100644 arch/arm/dts/k3-pinctrl.h
diff --git a/arch/arm/dts/k3-am62-main.dtsi b/arch/arm/dts/k3-am62-main.dtsi
index 4a42f1b2e314..2488e3a537fe 100644
--- a/arch/arm/dts/k3-am62-main.dtsi
+++ b/arch/arm/dts/k3-am62-main.dtsi
@@ -54,6 +54,12 @@
reg = <0x4044 0x8>;
#phy-cells = <1>;
};
+
+ epwm_tbclk: clock at 4130 {
+ compatible = "ti,am62-epwm-tbclk", "syscon";
+ reg = <0x4130 0x4>;
+ #clock-cells = <1>;
+ };
};
dmss: bus at 48000000 {
@@ -144,8 +150,8 @@
compatible = "ti,k2g-sci";
ti,host-id = <12>;
mbox-names = "rx", "tx";
- mboxes= <&secure_proxy_main 12>,
- <&secure_proxy_main 13>;
+ mboxes = <&secure_proxy_main 12>,
+ <&secure_proxy_main 13>;
reg-names = "debug_messages";
reg = <0x00 0x44043000 0x00 0xfe0>;
@@ -178,6 +184,21 @@
dma-names = "tx", "rx1", "rx2";
};
+ secure_proxy_sa3: mailbox at 43600000 {
+ compatible = "ti,am654-secure-proxy";
+ #mbox-cells = <1>;
+ reg-names = "target_data", "rt", "scfg";
+ reg = <0x00 0x43600000 0x00 0x10000>,
+ <0x00 0x44880000 0x00 0x20000>,
+ <0x00 0x44860000 0x00 0x20000>;
+ /*
+ * Marked Disabled:
+ * Node is incomplete as it is meant for bootloaders and
+ * firmware on non-MPU processors
+ */
+ status = "disabled";
+ };
+
main_pmx0: pinctrl at f4000 {
compatible = "pinctrl-single";
reg = <0x00 0xf4000 0x00 0x2ac>;
@@ -186,6 +207,108 @@
pinctrl-single,function-mask = <0xffffffff>;
};
+ main_esm: esm at 420000 {
+ compatible = "ti,j721e-esm";
+ reg = <0x00 0x420000 0x00 0x1000>;
+ ti,esm-pins = <160>, <161>, <162>, <163>, <177>, <178>;
+ };
+
+ main_timer0: timer at 2400000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2400000 0x00 0x400>;
+ interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 36 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 36 2>;
+ assigned-clock-parents = <&k3_clks 36 3>;
+ power-domains = <&k3_pds 36 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer1: timer at 2410000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2410000 0x00 0x400>;
+ interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 37 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 37 2>;
+ assigned-clock-parents = <&k3_clks 37 3>;
+ power-domains = <&k3_pds 37 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer2: timer at 2420000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2420000 0x00 0x400>;
+ interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 38 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 38 2>;
+ assigned-clock-parents = <&k3_clks 38 3>;
+ power-domains = <&k3_pds 38 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer3: timer at 2430000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2430000 0x00 0x400>;
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 39 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 39 2>;
+ assigned-clock-parents = <&k3_clks 39 3>;
+ power-domains = <&k3_pds 39 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer4: timer at 2440000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2440000 0x00 0x400>;
+ interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 40 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 40 2>;
+ assigned-clock-parents = <&k3_clks 40 3>;
+ power-domains = <&k3_pds 40 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer5: timer at 2450000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2450000 0x00 0x400>;
+ interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 41 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 41 2>;
+ assigned-clock-parents = <&k3_clks 41 3>;
+ power-domains = <&k3_pds 41 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer6: timer at 2460000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2460000 0x00 0x400>;
+ interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 42 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 42 2>;
+ assigned-clock-parents = <&k3_clks 42 3>;
+ power-domains = <&k3_pds 42 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
+ main_timer7: timer at 2470000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x2470000 0x00 0x400>;
+ interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 43 2>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 43 2>;
+ assigned-clock-parents = <&k3_clks 43 3>;
+ power-domains = <&k3_pds 43 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ };
+
main_uart0: serial at 2800000 {
compatible = "ti,am64-uart", "ti,am654-uart";
reg = <0x00 0x02800000 0x00 0x100>;
@@ -193,6 +316,7 @@
power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 146 0>;
clock-names = "fclk";
+ status = "disabled";
};
main_uart1: serial at 2810000 {
@@ -202,6 +326,7 @@
power-domains = <&k3_pds 152 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 152 0>;
clock-names = "fclk";
+ status = "disabled";
};
main_uart2: serial at 2820000 {
@@ -211,6 +336,7 @@
power-domains = <&k3_pds 153 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 153 0>;
clock-names = "fclk";
+ status = "disabled";
};
main_uart3: serial at 2830000 {
@@ -220,6 +346,7 @@
power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 154 0>;
clock-names = "fclk";
+ status = "disabled";
};
main_uart4: serial at 2840000 {
@@ -229,6 +356,7 @@
power-domains = <&k3_pds 155 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 155 0>;
clock-names = "fclk";
+ status = "disabled";
};
main_uart5: serial at 2850000 {
@@ -238,6 +366,7 @@
power-domains = <&k3_pds 156 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 156 0>;
clock-names = "fclk";
+ status = "disabled";
};
main_uart6: serial at 2860000 {
@@ -247,6 +376,7 @@
power-domains = <&k3_pds 158 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 158 0>;
clock-names = "fclk";
+ status = "disabled";
};
main_i2c0: i2c at 20000000 {
@@ -258,6 +388,7 @@
power-domains = <&k3_pds 102 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 102 2>;
clock-names = "fck";
+ status = "disabled";
};
main_i2c1: i2c at 20010000 {
@@ -269,6 +400,7 @@
power-domains = <&k3_pds 103 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 103 2>;
clock-names = "fck";
+ status = "disabled";
};
main_i2c2: i2c at 20020000 {
@@ -280,6 +412,7 @@
power-domains = <&k3_pds 104 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 104 2>;
clock-names = "fck";
+ status = "disabled";
};
main_i2c3: i2c at 20030000 {
@@ -291,6 +424,7 @@
power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 105 2>;
clock-names = "fck";
+ status = "disabled";
};
main_spi0: spi at 20100000 {
@@ -300,7 +434,8 @@
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&k3_pds 141 TI_SCI_PD_EXCLUSIVE>;
- clocks = <&k3_clks 172 0>;
+ clocks = <&k3_clks 141 0>;
+ status = "disabled";
};
main_spi1: spi at 20110000 {
@@ -310,7 +445,8 @@
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&k3_pds 142 TI_SCI_PD_EXCLUSIVE>;
- clocks = <&k3_clks 173 0>;
+ clocks = <&k3_clks 142 0>;
+ status = "disabled";
};
main_spi2: spi at 20120000 {
@@ -320,7 +456,8 @@
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&k3_pds 143 TI_SCI_PD_EXCLUSIVE>;
- clocks = <&k3_clks 174 0>;
+ clocks = <&k3_clks 143 0>;
+ status = "disabled";
};
main_gpio_intr: interrupt-controller at a00000 {
@@ -345,7 +482,7 @@
<193>, <194>, <195>;
interrupt-controller;
#interrupt-cells = <2>;
- ti,ngpio = <87>;
+ ti,ngpio = <92>;
ti,davinci-gpio-unbanked = <0>;
power-domains = <&k3_pds 77 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 77 0>;
@@ -362,7 +499,7 @@
<183>, <184>, <185>;
interrupt-controller;
#interrupt-cells = <2>;
- ti,ngpio = <88>;
+ ti,ngpio = <52>;
ti,davinci-gpio-unbanked = <0>;
power-domains = <&k3_pds 78 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 78 0>;
@@ -385,8 +522,11 @@
ti,clkbuf-sel = <0x7>;
ti,otap-del-sel-legacy = <0x0>;
ti,otap-del-sel-mmc-hs = <0x0>;
- ti,otap-del-sel-ddr52 = <0x9>;
- ti,otap-del-sel-hs200 = <0x6>;
+ ti,otap-del-sel-ddr52 = <0x5>;
+ ti,otap-del-sel-hs200 = <0x5>;
+ ti,itap-del-sel-legacy = <0xa>;
+ ti,itap-del-sel-mmc-hs = <0x1>;
+ status = "disabled";
};
sdhci1: mmc at fa00000 {
@@ -397,19 +537,20 @@
clocks = <&k3_clks 58 5>, <&k3_clks 58 6>;
clock-names = "clk_ahb", "clk_xin";
ti,trm-icp = <0x2>;
- ti,otap-del-sel-legacy = <0x0>;
+ ti,otap-del-sel-legacy = <0x8>;
ti,otap-del-sel-sd-hs = <0x0>;
- ti,otap-del-sel-sdr12 = <0xf>;
- ti,otap-del-sel-sdr25 = <0xf>;
- ti,otap-del-sel-sdr50 = <0xc>;
- ti,otap-del-sel-sdr104 = <0x6>;
- ti,otap-del-sel-ddr50 = <0x9>;
- ti,itap-del-sel-legacy = <0x0>;
- ti,itap-del-sel-sd-hs = <0x0>;
- ti,itap-del-sel-sdr12 = <0x0>;
- ti,itap-del-sel-sdr25 = <0x0>;
+ ti,otap-del-sel-sdr12 = <0x0>;
+ ti,otap-del-sel-sdr25 = <0x0>;
+ ti,otap-del-sel-sdr50 = <0x8>;
+ ti,otap-del-sel-sdr104 = <0x7>;
+ ti,otap-del-sel-ddr50 = <0x4>;
+ ti,itap-del-sel-legacy = <0xa>;
+ ti,itap-del-sel-sd-hs = <0x1>;
+ ti,itap-del-sel-sdr12 = <0xa>;
+ ti,itap-del-sel-sdr25 = <0x1>;
ti,clkbuf-sel = <0x7>;
bus-width = <4>;
+ status = "disabled";
};
sdhci2: mmc at fa20000 {
@@ -420,18 +561,65 @@
clocks = <&k3_clks 184 5>, <&k3_clks 184 6>;
clock-names = "clk_ahb", "clk_xin";
ti,trm-icp = <0x2>;
- ti,otap-del-sel-legacy = <0x0>;
+ ti,otap-del-sel-legacy = <0x8>;
ti,otap-del-sel-sd-hs = <0x0>;
- ti,otap-del-sel-sdr12 = <0xf>;
- ti,otap-del-sel-sdr25 = <0xf>;
- ti,otap-del-sel-sdr50 = <0xc>;
- ti,otap-del-sel-sdr104 = <0x6>;
- ti,otap-del-sel-ddr50 = <0x9>;
- ti,itap-del-sel-legacy = <0x0>;
- ti,itap-del-sel-sd-hs = <0x0>;
- ti,itap-del-sel-sdr12 = <0x0>;
- ti,itap-del-sel-sdr25 = <0x0>;
+ ti,otap-del-sel-sdr12 = <0x0>;
+ ti,otap-del-sel-sdr25 = <0x0>;
+ ti,otap-del-sel-sdr50 = <0x8>;
+ ti,otap-del-sel-sdr104 = <0x7>;
+ ti,otap-del-sel-ddr50 = <0x8>;
+ ti,itap-del-sel-legacy = <0xa>;
+ ti,itap-del-sel-sd-hs = <0xa>;
+ ti,itap-del-sel-sdr12 = <0xa>;
+ ti,itap-del-sel-sdr25 = <0x1>;
ti,clkbuf-sel = <0x7>;
+ status = "disabled";
+ };
+
+ usbss0: dwc3-usb at f900000 {
+ compatible = "ti,am62-usb";
+ reg = <0x00 0x0f900000 0x00 0x800>;
+ clocks = <&k3_clks 161 3>;
+ clock-names = "ref";
+ ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
+ ranges;
+ status = "disabled";
+
+ usb0: usb at 31000000 {
+ compatible = "snps,dwc3";
+ reg =<0x00 0x31000000 0x00 0x50000>;
+ interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+ <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+ interrupt-names = "host", "peripheral";
+ maximum-speed = "high-speed";
+ dr_mode = "otg";
+ };
+ };
+
+ usbss1: dwc3-usb at f910000 {
+ compatible = "ti,am62-usb";
+ reg = <0x00 0x0f910000 0x00 0x800>;
+ clocks = <&k3_clks 162 3>;
+ clock-names = "ref";
+ ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
+ ranges;
+ status = "disabled";
+
+ usb1: usb at 31100000 {
+ compatible = "snps,dwc3";
+ reg =<0x00 0x31100000 0x00 0x50000>;
+ interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+ <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+ interrupt-names = "host", "peripheral";
+ maximum-speed = "high-speed";
+ dr_mode = "otg";
+ };
};
fss: bus at fc00000 {
@@ -456,6 +644,7 @@
power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>;
#address-cells = <1>;
#size-cells = <0>;
+ status = "disabled";
};
};
@@ -514,12 +703,13 @@
clocks = <&k3_clks 13 0>;
clock-names = "fck";
bus_freq = <1000000>;
+ status = "disabled";
};
cpts at 3d000 {
compatible = "ti,j721e-cpts";
reg = <0x00 0x3d000 0x00 0x400>;
- clocks = <&k3_clks 13 1>;
+ clocks = <&k3_clks 13 3>;
clock-names = "cpts";
interrupts-extended = <&gic500 GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "cpts";
@@ -551,6 +741,7 @@
power-domains = <&k3_pds 51 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 51 0>;
clock-names = "fck";
+ status = "disabled";
};
ecap1: pwm at 23110000 {
@@ -560,6 +751,7 @@
power-domains = <&k3_pds 52 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 52 0>;
clock-names = "fck";
+ status = "disabled";
};
ecap2: pwm at 23120000 {
@@ -569,6 +761,7 @@
power-domains = <&k3_pds 53 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 53 0>;
clock-names = "fck";
+ status = "disabled";
};
main_mcan0: can at 20701000 {
@@ -583,5 +776,141 @@
<GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "int0", "int1";
bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+ status = "disabled";
+ };
+
+ main_rti0: watchdog at e000000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x0e000000 0x00 0x100>;
+ clocks = <&k3_clks 125 0>;
+ power-domains = <&k3_pds 125 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 125 0>;
+ assigned-clock-parents = <&k3_clks 125 2>;
+ };
+
+ main_rti1: watchdog at e010000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x0e010000 0x00 0x100>;
+ clocks = <&k3_clks 126 0>;
+ power-domains = <&k3_pds 126 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 126 0>;
+ assigned-clock-parents = <&k3_clks 126 2>;
+ };
+
+ main_rti2: watchdog at e020000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x0e020000 0x00 0x100>;
+ clocks = <&k3_clks 127 0>;
+ power-domains = <&k3_pds 127 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 127 0>;
+ assigned-clock-parents = <&k3_clks 127 2>;
+ };
+
+ main_rti3: watchdog at e030000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x0e030000 0x00 0x100>;
+ clocks = <&k3_clks 128 0>;
+ power-domains = <&k3_pds 128 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 128 0>;
+ assigned-clock-parents = <&k3_clks 128 2>;
+ };
+
+ main_rti15: watchdog at e0f0000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x0e0f0000 0x00 0x100>;
+ clocks = <&k3_clks 130 0>;
+ power-domains = <&k3_pds 130 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 130 0>;
+ assigned-clock-parents = <&k3_clks 130 2>;
+ };
+
+ epwm0: pwm at 23000000 {
+ compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x00 0x23000000 0x00 0x100>;
+ power-domains = <&k3_pds 86 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&epwm_tbclk 0>, <&k3_clks 86 0>;
+ clock-names = "tbclk", "fck";
+ status = "disabled";
+ };
+
+ epwm1: pwm at 23010000 {
+ compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x00 0x23010000 0x00 0x100>;
+ power-domains = <&k3_pds 87 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&epwm_tbclk 1>, <&k3_clks 87 0>;
+ clock-names = "tbclk", "fck";
+ status = "disabled";
+ };
+
+ epwm2: pwm at 23020000 {
+ compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+ #pwm-cells = <3>;
+ reg = <0x00 0x23020000 0x00 0x100>;
+ power-domains = <&k3_pds 88 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&epwm_tbclk 2>, <&k3_clks 88 0>;
+ clock-names = "tbclk", "fck";
+ status = "disabled";
+ };
+
+ mcasp0: audio-controller at 2b00000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b00000 0x00 0x2000>,
+ <0x00 0x02b08000 0x00 0x400>;
+ reg-names = "mpu", "dat";
+ interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc500 0>, <&main_bcdma 0 0x4500 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 190 0>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 190 0>;
+ assigned-clock-parents = <&k3_clks 190 2>;
+ power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
+ status = "disabled";
+ };
+
+ mcasp1: audio-controller at 2b10000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b10000 0x00 0x2000>,
+ <0x00 0x02b18000 0x00 0x400>;
+ reg-names = "mpu", "dat";
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc501 0>, <&main_bcdma 0 0x4501 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 191 0>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 191 0>;
+ assigned-clock-parents = <&k3_clks 191 2>;
+ power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
+ status = "disabled";
+ };
+
+ mcasp2: audio-controller at 2b20000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ reg = <0x00 0x02b20000 0x00 0x2000>,
+ <0x00 0x02b28000 0x00 0x400>;
+ reg-names = "mpu", "dat";
+ interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ dmas = <&main_bcdma 0 0xc502 0>, <&main_bcdma 0 0x4502 0>;
+ dma-names = "tx", "rx";
+
+ clocks = <&k3_clks 192 0>;
+ clock-names = "fck";
+ assigned-clocks = <&k3_clks 192 0>;
+ assigned-clock-parents = <&k3_clks 192 2>;
+ power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
+ status = "disabled";
};
};
diff --git a/arch/arm/dts/k3-am62-mcu.dtsi b/arch/arm/dts/k3-am62-mcu.dtsi
index f56c803560f2..19fc38157d94 100644
--- a/arch/arm/dts/k3-am62-mcu.dtsi
+++ b/arch/arm/dts/k3-am62-mcu.dtsi
@@ -14,6 +14,57 @@
pinctrl-single,function-mask = <0xffffffff>;
};
+ mcu_esm: esm at 4100000 {
+ compatible = "ti,j721e-esm";
+ reg = <0x00 0x4100000 0x00 0x1000>;
+ ti,esm-pins = <0>, <1>, <2>, <85>;
+ };
+
+ /*
+ * The MCU domain timer interrupts are routed only to the ESM module,
+ * and not currently available for Linux. The MCU domain timers are
+ * of limited use without interrupts, and likely reserved by the ESM.
+ */
+ mcu_timer0: timer at 4800000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x4800000 0x00 0x400>;
+ clocks = <&k3_clks 35 2>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 35 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ status = "reserved";
+ };
+
+ mcu_timer1: timer at 4810000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x4810000 0x00 0x400>;
+ clocks = <&k3_clks 48 2>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 48 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ status = "reserved";
+ };
+
+ mcu_timer2: timer at 4820000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x4820000 0x00 0x400>;
+ clocks = <&k3_clks 49 2>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 49 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ status = "reserved";
+ };
+
+ mcu_timer3: timer at 4830000 {
+ compatible = "ti,am654-timer";
+ reg = <0x00 0x4830000 0x00 0x400>;
+ clocks = <&k3_clks 50 2>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 50 TI_SCI_PD_EXCLUSIVE>;
+ ti,timer-pwm;
+ status = "reserved";
+ };
+
mcu_uart0: serial at 4a00000 {
compatible = "ti,am64-uart", "ti,am654-uart";
reg = <0x00 0x04a00000 0x00 0x100>;
@@ -21,6 +72,7 @@
power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 149 0>;
clock-names = "fclk";
+ status = "disabled";
};
mcu_i2c0: i2c at 4900000 {
@@ -32,6 +84,7 @@
power-domains = <&k3_pds 106 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 106 2>;
clock-names = "fck";
+ status = "disabled";
};
mcu_spi0: spi at 4b00000 {
@@ -42,6 +95,7 @@
#size-cells = <0>;
power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 147 0>;
+ status = "disabled";
};
mcu_spi1: spi at 4b10000 {
@@ -52,6 +106,7 @@
#size-cells = <0>;
power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 148 0>;
+ status = "disabled";
};
mcu_gpio_intr: interrupt-controller at 4210000 {
@@ -81,4 +136,15 @@
clocks = <&k3_clks 79 0>;
clock-names = "gpio";
};
+
+ mcu_rti0: watchdog at 4880000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x04880000 0x00 0x100>;
+ clocks = <&k3_clks 131 0>;
+ power-domains = <&k3_pds 131 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 131 0>;
+ assigned-clock-parents = <&k3_clks 131 2>;
+ /* Tightly coupled to M4F */
+ status = "reserved";
+ };
};
diff --git a/arch/arm/dts/k3-am62-thermal.dtsi b/arch/arm/dts/k3-am62-thermal.dtsi
new file mode 100644
index 000000000000..a358757e26f0
--- /dev/null
+++ b/arch/arm/dts/k3-am62-thermal.dtsi
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/thermal/thermal.h>
+
+thermal_zones: thermal-zones {
+ main0_thermal: main0-thermal {
+ polling-delay-passive = <250>; /* milliSeconds */
+ polling-delay = <500>; /* milliSeconds */
+ thermal-sensors = <&wkup_vtm0 0>;
+
+ trips {
+ main0_crit: main0-crit {
+ temperature = <105000>; /* milliCelsius */
+ hysteresis = <2000>; /* milliCelsius */
+ type = "critical";
+ };
+ };
+ };
+
+ main1_thermal: main1-thermal {
+ polling-delay-passive = <250>; /* milliSeconds */
+ polling-delay = <500>; /* milliSeconds */
+ thermal-sensors = <&wkup_vtm0 1>;
+
+ trips {
+ main1_crit: main1-crit {
+ temperature = <105000>; /* milliCelsius */
+ hysteresis = <2000>; /* milliCelsius */
+ type = "critical";
+ };
+ };
+ };
+};
diff --git a/arch/arm/dts/k3-am62-wakeup.dtsi b/arch/arm/dts/k3-am62-wakeup.dtsi
index 4090134676cf..eae052887186 100644
--- a/arch/arm/dts/k3-am62-wakeup.dtsi
+++ b/arch/arm/dts/k3-am62-wakeup.dtsi
@@ -26,16 +26,47 @@
power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 114 0>;
clock-names = "fclk";
+ status = "disabled";
};
wkup_i2c0: i2c at 2b200000 {
compatible = "ti,am64-i2c", "ti,omap4-i2c";
- reg = <0x00 0x02b200000 0x00 0x100>;
+ reg = <0x00 0x2b200000 0x00 0x100>;
interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
power-domains = <&k3_pds 107 TI_SCI_PD_EXCLUSIVE>;
clocks = <&k3_clks 107 4>;
clock-names = "fck";
+ status = "disabled";
+ };
+
+ wkup_rtc0: rtc at 2b1f0000 {
+ compatible = "ti,am62-rtc";
+ reg = <0x00 0x2b1f0000 0x00 0x100>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&k3_clks 117 6> , <&k3_clks 117 0>;
+ clock-names = "vbus", "osc32k";
+ power-domains = <&k3_pds 117 TI_SCI_PD_EXCLUSIVE>;
+ wakeup-source;
+ };
+
+ wkup_rti0: watchdog at 2b000000 {
+ compatible = "ti,j7-rti-wdt";
+ reg = <0x00 0x2b000000 0x00 0x100>;
+ clocks = <&k3_clks 132 0>;
+ power-domains = <&k3_pds 132 TI_SCI_PD_EXCLUSIVE>;
+ assigned-clocks = <&k3_clks 132 0>;
+ assigned-clock-parents = <&k3_clks 132 2>;
+ /* Used by DM firmware */
+ status = "reserved";
+ };
+
+ wkup_vtm0: temperature-sensor at b00000 {
+ compatible = "ti,j7200-vtm";
+ reg = <0x00 0xb00000 0x00 0x400>,
+ <0x00 0xb01000 0x00 0x400>;
+ power-domains = <&k3_pds 95 TI_SCI_PD_EXCLUSIVE>;
+ #thermal-sensor-cells = <1>;
};
};
diff --git a/arch/arm/dts/k3-am62.dtsi b/arch/arm/dts/k3-am62.dtsi
index 37fcbe7a3c33..5e72c445f37a 100644
--- a/arch/arm/dts/k3-am62.dtsi
+++ b/arch/arm/dts/k3-am62.dtsi
@@ -8,9 +8,10 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/k3.h>
#include <dt-bindings/soc/ti,sci_pm_domain.h>
+#include "k3-pinctrl.h"
+
/ {
model = "Texas Instruments K3 AM625 SoC";
compatible = "ti,am625";
@@ -80,6 +81,7 @@
<0x00 0x04000000 0x00 0x04000000 0x00 0x01ff1400>,
/* Wakeup Domain Range */
+ <0x00 0x00b00000 0x00 0x00b00000 0x00 0x00002400>, /* VTM */
<0x00 0x2b000000 0x00 0x2b000000 0x00 0x00300400>,
<0x00 0x43000000 0x00 0x43000000 0x00 0x00020000>;
@@ -90,14 +92,17 @@
ranges = <0x00 0x04000000 0x00 0x04000000 0x00 0x01ff1400>; /* Peripheral window */
};
- cbass_wakeup: bus at 2b000000 {
+ cbass_wakeup: bus at b00000 {
compatible = "simple-bus";
#address-cells = <2>;
#size-cells = <2>;
- ranges = <0x00 0x2b000000 0x00 0x2b000000 0x00 0x00300400>, /* Peripheral Window */
+ ranges = <0x00 0x00b00000 0x00 0x00b00000 0x00 0x00002400>, /* VTM */
+ <0x00 0x2b000000 0x00 0x2b000000 0x00 0x00300400>, /* Peripheral Window */
<0x00 0x43000000 0x00 0x43000000 0x00 0x00020000>;
};
};
+
+ #include "k3-am62-thermal.dtsi"
};
/* Now include the peripherals for each bus segments */
diff --git a/arch/arm/dts/k3-am625-r5-sk.dts b/arch/arm/dts/k3-am625-r5-sk.dts
index 3ec5bad73503..bf219226b974 100644
--- a/arch/arm/dts/k3-am625-r5-sk.dts
+++ b/arch/arm/dts/k3-am625-r5-sk.dts
@@ -9,7 +9,6 @@
#include "k3-am62-ddr.dtsi"
#include "k3-am625-sk-u-boot.dtsi"
-#include "k3-am625-sk-binman.dtsi"
/ {
aliases {
@@ -19,31 +18,6 @@
serial3 = &main_uart1;
};
- chosen {
- stdout-path = "serial2:115200n8";
- tick-timer = &timer1;
- };
-
- memory at 80000000 {
- device_type = "memory";
- /* 2G RAM */
- reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
-
- bootph-pre-ram;
- };
-
- reserved-memory {
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- secure_ddr: optee at 9e800000 {
- reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
- alignment = <0x1000>;
- no-map;
- };
- };
-
a53_0: a53 at 0 {
compatible = "ti,am654-rproc";
reg = <0x00 0x00a90000 0x00 0x10>;
@@ -81,80 +55,44 @@
ti,secure-host;
};
-&cbass_mcu {
- mcu_esm: esm at 4100000 {
- compatible = "ti,j721e-esm";
- reg = <0x0 0x4100000 0x0 0x1000>;
- ti,esm-pins = <0>, <1>, <2>, <85>;
- bootph-pre-ram;
- };
+&mcu_esm {
+ bootph-pre-ram;
};
-&cbass_main {
- sa3_secproxy: secproxy at 44880000 {
- bootph-pre-ram;
- compatible = "ti,am654-secure-proxy";
- #mbox-cells = <1>;
- reg-names = "rt", "scfg", "target_data";
- reg = <0x00 0x44880000 0x00 0x20000>,
- <0x0 0x44860000 0x0 0x20000>,
- <0x0 0x43600000 0x0 0x10000>;
- };
+&secure_proxy_sa3 {
+ bootph-pre-ram;
+ /* We require this for boot handshake */
+ status = "okay";
+};
+
+&main_esm {
+ bootph-pre-ram;
+};
+&cbass_main {
sysctrler: sysctrler {
compatible = "ti,am654-system-controller";
- mboxes= <&secure_proxy_main 1>, <&secure_proxy_main 0>, <&sa3_secproxy 0>;
+ mboxes= <&secure_proxy_main 1>, <&secure_proxy_main 0>, <&secure_proxy_sa3 0>;
mbox-names = "tx", "rx", "boot_notify";
bootph-pre-ram;
};
-
- main_esm: esm at 420000 {
- compatible = "ti,j721e-esm";
- reg = <0x0 0x420000 0x0 0x1000>;
- ti,esm-pins = <160>, <161>, <162>, <163>, <177>, <178>;
- bootph-pre-ram;
- };
};
-&mcu_pmx0 {
+&wkup_uart0_pins_default {
bootph-pre-ram;
- wkup_uart0_pins_default: wkup-uart0-pins-default {
- pinctrl-single,pins = <
- AM62X_MCU_IOPAD(0x02c, PIN_INPUT, 0) /* (C6) WKUP_UART0_CTSn */
- AM62X_MCU_IOPAD(0x030, PIN_OUTPUT, 0) /* (A4) WKUP_UART0_RTSn */
- AM62X_MCU_IOPAD(0x024, PIN_INPUT, 0) /* (B4) WKUP_UART0_RXD */
- AM62X_MCU_IOPAD(0x028, PIN_OUTPUT, 0) /* (C5) WKUP_UART0_TXD */
- >;
- bootph-pre-ram;
- };
};
-&main_pmx0 {
+&main_uart1_pins_default {
bootph-pre-ram;
- main_uart1_pins_default: main-uart1-pins-default {
- pinctrl-single,pins = <
- AM62X_IOPAD(0x194, PIN_INPUT, 2) /* (B19) MCASP0_AXR3.UART1_CTSn */
- AM62X_IOPAD(0x198, PIN_OUTPUT, 2) /* (A19) MCASP0_AXR2.UART1_RTSn */
- AM62X_IOPAD(0x1ac, PIN_INPUT, 2) /* (E19) MCASP0_AFSR.UART1_RXD */
- AM62X_IOPAD(0x1b0, PIN_OUTPUT, 2) /* (A20) MCASP0_ACLKR.UART1_TXD */
- >;
- bootph-pre-ram;
- };
};
/* WKUP UART0 is used for DM firmware logs */
&wkup_uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&wkup_uart0_pins_default>;
- status = "okay";
bootph-pre-ram;
};
/* Main UART1 is used for TIFS firmware logs */
&main_uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&main_uart1_pins_default>;
- status = "okay";
bootph-pre-ram;
};
diff --git a/arch/arm/dts/k3-am625-sk-u-boot.dtsi b/arch/arm/dts/k3-am625-sk-u-boot.dtsi
index a60c37f1dbf0..76589c7025a0 100644
--- a/arch/arm/dts/k3-am625-sk-u-boot.dtsi
+++ b/arch/arm/dts/k3-am625-sk-u-boot.dtsi
@@ -9,7 +9,7 @@
/ {
chosen {
stdout-path = "serial2:115200n8";
- tick-timer = &timer1;
+ tick-timer = &main_timer0;
};
aliases {
@@ -21,16 +21,13 @@
};
};
-&cbass_main{
+&cbass_main {
bootph-pre-ram;
+};
- timer1: timer at 2400000 {
- compatible = "ti,omap5430-timer";
- reg = <0x00 0x2400000 0x00 0x80>;
- ti,timer-alwon;
- clock-frequency = <25000000>;
- bootph-pre-ram;
- };
+&main_timer0 {
+ clock-frequency = <25000000>;
+ bootph-pre-ram;
};
&dmss {
@@ -77,10 +74,6 @@
bootph-pre-ram;
};
-&main_uart1 {
- bootph-pre-ram;
-};
-
&cbass_mcu {
bootph-pre-ram;
};
@@ -93,10 +86,6 @@
bootph-pre-ram;
};
-&wkup_uart0 {
- bootph-pre-ram;
-};
-
&sdhci1 {
bootph-pre-ram;
};
@@ -135,6 +124,7 @@
reg-names = "cpsw_nuss", "mac_efuse";
/delete-property/ ranges;
bootph-pre-ram;
+ pinctrl-0 = <&main_mdio1_pins_default &main_rgmii1_pins_default>;
cpsw-phy-sel at 04044 {
compatible = "ti,am64-phy-gmii-sel";
diff --git a/arch/arm/dts/k3-am625-sk.dts b/arch/arm/dts/k3-am625-sk.dts
index af5617ff44d2..3f9ef4053aa6 100644
--- a/arch/arm/dts/k3-am625-sk.dts
+++ b/arch/arm/dts/k3-am625-sk.dts
@@ -7,28 +7,19 @@
/dts-v1/;
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/net/ti-dp83867.h>
-#include "k3-am625.dtsi"
+#include "k3-am62x-sk-common.dtsi"
/ {
- compatible = "ti,am625-sk", "ti,am625";
+ compatible = "ti,am625-sk", "ti,am625";
model = "Texas Instruments AM625 SK";
- aliases {
- serial2 = &main_uart0;
- mmc0 = &sdhci0;
- mmc1 = &sdhci1;
- mmc2 = &sdhci2;
- spi0 = &ospi0;
- ethernet0 = &cpsw_port1;
- ethernet1 = &cpsw_port2;
- };
-
- chosen {
- stdout-path = "serial2:115200n8";
- bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
+ opp-table {
+ /* Add 1.4GHz OPP for am625-sk board. Requires VDD_CORE to be at 0.85V */
+ opp-1400000000 {
+ opp-hz = /bits/ 64 <1400000000>;
+ opp-supported-hw = <0x01 0x0004>;
+ clock-latency-ns = <6000000>;
+ };
};
memory at 80000000 {
@@ -38,39 +29,6 @@
};
- reserved-memory {
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- ramoops at 9ca00000 {
- compatible = "ramoops";
- reg = <0x00 0x9ca00000 0x00 0x00100000>;
- record-size = <0x8000>;
- console-size = <0x8000>;
- ftrace-size = <0x00>;
- pmsg-size = <0x8000>;
- };
-
- secure_tfa_ddr: tfa at 9e780000 {
- reg = <0x00 0x9e780000 0x00 0x80000>;
- alignment = <0x1000>;
- no-map;
- };
-
- secure_ddr: optee at 9e800000 {
- reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
- alignment = <0x1000>;
- no-map;
- };
-
- wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory at 9db00000 {
- compatible = "shared-dma-pool";
- reg = <0x00 0x9db00000 0x00 0xc00000>;
- no-map;
- };
- };
-
vmain_pd: regulator-0 {
/* TPS65988 PD CONTROLLER OUTPUT */
compatible = "regulator-fixed";
@@ -130,108 +88,20 @@
<3300000 0x1>;
};
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&usr_led_pins_default>;
-
- led-0 {
- label = "am62-sk:green:heartbeat";
- gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- function = LED_FUNCTION_HEARTBEAT;
- default-state = "off";
- };
+ vcc_1v8: regulator-5 {
+ /* output of TPS6282518DMQ */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3_sys>;
+ regulator-always-on;
+ regulator-boot-on;
};
};
&main_pmx0 {
- main_uart0_pins_default: main-uart0-pins-default {
- pinctrl-single,pins = <
- AM62X_IOPAD(0x1c8, PIN_INPUT, 0) /* (D14) UART0_RXD */
- AM62X_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (E14) UART0_TXD */
- >;
- };
-
- main_i2c0_pins_default: main-i2c0-pins-default {
- pinctrl-single,pins = <
- AM62X_IOPAD(0x1e0, PIN_INPUT_PULLUP, 0) /* (B16) I2C0_SCL */
- AM62X_IOPAD(0x1e4, PIN_INPUT_PULLUP, 0) /* (A16) I2C0_SDA */
- >;
- };
-
- main_i2c1_pins_default: main-i2c1-pins-default {
- pinctrl-single,pins = <
- AM62X_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */
- AM62X_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
- >;
- };
-
- main_i2c2_pins_default: main-i2c2-pins-default {
- pinctrl-single,pins = <
- AM62X_IOPAD(0x0b0, PIN_INPUT_PULLUP, 1) /* (K22) GPMC0_CSn2.I2C2_SCL */
- AM62X_IOPAD(0x0b4, PIN_INPUT_PULLUP, 1) /* (K24) GPMC0_CSn3.I2C2_SDA */
- >;
- };
-
- main_mmc0_pins_default: main-mmc0-pins-default {
- pinctrl-single,pins = <
- AM62X_IOPAD(0x220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */
- AM62X_IOPAD(0x218, PIN_INPUT, 0) /* (AB1) MMC0_CLK */
- AM62X_IOPAD(0x214, PIN_INPUT, 0) /* (AA2) MMC0_DAT0 */
- AM62X_IOPAD(0x210, PIN_INPUT, 0) /* (AA1) MMC0_DAT1 */
- AM62X_IOPAD(0x20c, PIN_INPUT, 0) /* (AA3) MMC0_DAT2 */
- AM62X_IOPAD(0x208, PIN_INPUT, 0) /* (Y4) MMC0_DAT3 */
- AM62X_IOPAD(0x204, PIN_INPUT, 0) /* (AB2) MMC0_DAT4 */
- AM62X_IOPAD(0x200, PIN_INPUT, 0) /* (AC1) MMC0_DAT5 */
- AM62X_IOPAD(0x1fc, PIN_INPUT, 0) /* (AD2) MMC0_DAT6 */
- AM62X_IOPAD(0x1f8, PIN_INPUT, 0) /* (AC2) MMC0_DAT7 */
- >;
- };
-
- main_mmc1_pins_default: main-mmc1-pins-default {
- pinctrl-single,pins = <
- AM62X_IOPAD(0x23c, PIN_INPUT, 0) /* (A21) MMC1_CMD */
- AM62X_IOPAD(0x234, PIN_INPUT, 0) /* (B22) MMC1_CLK */
- AM62X_IOPAD(0x230, PIN_INPUT, 0) /* (A22) MMC1_DAT0 */
- AM62X_IOPAD(0x22c, PIN_INPUT, 0) /* (B21) MMC1_DAT1 */
- AM62X_IOPAD(0x228, PIN_INPUT, 0) /* (C21) MMC1_DAT2 */
- AM62X_IOPAD(0x224, PIN_INPUT, 0) /* (D22) MMC1_DAT3 */
- AM62X_IOPAD(0x240, PIN_INPUT, 0) /* (D17) MMC1_SDCD */
- >;
- };
-
- usr_led_pins_default: usr-led-pins-default {
- pinctrl-single,pins = <
- AM62X_IOPAD(0x244, PIN_OUTPUT, 7) /* (C17) MMC1_SDWP.GPIO1_49 */
- >;
- };
-
- main_mdio1_pins_default: main-mdio1-pins-default {
- pinctrl-single,pins = <
- AM62X_IOPAD(0x160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC */
- AM62X_IOPAD(0x15c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO */
- >;
- };
-
- main_rgmii1_pins_default: main-rgmii1-pins-default {
- pinctrl-single,pins = <
- AM62X_IOPAD(0x14c, PIN_INPUT, 0) /* (AB17) RGMII1_RD0 */
- AM62X_IOPAD(0x150, PIN_INPUT, 0) /* (AC17) RGMII1_RD1 */
- AM62X_IOPAD(0x154, PIN_INPUT, 0) /* (AB16) RGMII1_RD2 */
- AM62X_IOPAD(0x158, PIN_INPUT, 0) /* (AA15) RGMII1_RD3 */
- AM62X_IOPAD(0x148, PIN_INPUT, 0) /* (AD17) RGMII1_RXC */
- AM62X_IOPAD(0x144, PIN_INPUT, 0) /* (AE17) RGMII1_RX_CTL */
- AM62X_IOPAD(0x134, PIN_OUTPUT, 0) /* (AE20) RGMII1_TD0 */
- AM62X_IOPAD(0x138, PIN_OUTPUT, 0) /* (AD20) RGMII1_TD1 */
- AM62X_IOPAD(0x13c, PIN_OUTPUT, 0) /* (AE18) RGMII1_TD2 */
- AM62X_IOPAD(0x140, PIN_OUTPUT, 0) /* (AD18) RGMII1_TD3 */
- AM62X_IOPAD(0x130, PIN_OUTPUT, 0) /* (AE19) RGMII1_TXC */
- AM62X_IOPAD(0x12c, PIN_OUTPUT, 0) /* (AD19) RGMII1_TX_CTL */
- >;
- };
-
- main_rgmii2_pins_default: main-rgmii2-pins-default {
+ main_rgmii2_pins_default: main-rgmii2-default-pins {
pinctrl-single,pins = <
AM62X_IOPAD(0x184, PIN_INPUT, 0) /* (AE23) RGMII2_RD0 */
AM62X_IOPAD(0x188, PIN_INPUT, 0) /* (AB20) RGMII2_RD1 */
@@ -248,7 +118,7 @@
>;
};
- ospi0_pins_default: ospi0-pins-default {
+ ospi0_pins_default: ospi0-default-pins {
pinctrl-single,pins = <
AM62X_IOPAD(0x000, PIN_OUTPUT, 0) /* (H24) OSPI0_CLK */
AM62X_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F23) OSPI0_CSn0 */
@@ -264,77 +134,20 @@
>;
};
- vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
+ vdd_sd_dv_pins_default: vdd-sd-dv-default-pins {
pinctrl-single,pins = <
AM62X_IOPAD(0x07c, PIN_OUTPUT, 7) /* (P25) GPMC0_CLK.GPIO0_31 */
>;
};
- main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-pins-default {
+ main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-default-pins {
pinctrl-single,pins = <
AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
>;
};
};
-&wkup_uart0 {
- /* WKUP UART0 is used by DM firmware */
- status = "reserved";
-};
-
-&mcu_uart0 {
- status = "disabled";
-};
-
-&main_uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&main_uart0_pins_default>;
-};
-
-&main_uart1 {
- /* Main UART1 is used by TIFS firmware */
- status = "reserved";
-};
-
-&main_uart2 {
- status = "disabled";
-};
-
-&main_uart3 {
- status = "disabled";
-};
-
-&main_uart4 {
- status = "disabled";
-};
-
-&main_uart5 {
- status = "disabled";
-};
-
-&main_uart6 {
- status = "disabled";
-};
-
-&mcu_i2c0 {
- status = "disabled";
-};
-
-&wkup_i2c0 {
- status = "disabled";
-};
-
-&main_i2c0 {
- status = "disabled";
- pinctrl-0 = <&main_i2c0_pins_default>;
- clock-frequency = <400000>;
-};
-
&main_i2c1 {
- status = "disabled";
- pinctrl-0 = <&main_i2c1_pins_default>;
- clock-frequency = <400000>;
-
exp1: gpio at 22 {
compatible = "ti,tca6424";
reg = <0x22>;
@@ -348,7 +161,7 @@
"UART1_FET_BUF_EN", "WL_LT_EN",
"GPIO_HDMI_RSTn", "CSI_GPIO1",
"CSI_GPIO2", "PRU_3V3_EN",
- "HDMI_INTn", "TEST_GPIO2",
+ "HDMI_INTn", "PD_I2C_IRQ",
"MCASP1_FET_EN", "MCASP1_BUF_BT_EN",
"MCASP1_FET_SEL", "UART1_FET_SEL",
"TSINT#", "IO_EXP_TEST_LED";
@@ -363,41 +176,14 @@
};
};
-&main_i2c2 {
- status = "disabled";
-};
-
-&main_i2c3 {
- status = "disabled";
-};
-
-&sdhci0 {
- pinctrl-names = "default";
- pinctrl-0 = <&main_mmc0_pins_default>;
- ti,driver-strength-ohm = <50>;
- disable-wp;
-};
-
&sdhci1 {
- /* SD/MMC */
vmmc-supply = <&vdd_mmc1>;
vqmmc-supply = <&vdd_sd_dv>;
- pinctrl-names = "default";
- pinctrl-0 = <&main_mmc1_pins_default>;
- ti,driver-strength-ohm = <50>;
- disable-wp;
};
&cpsw3g {
pinctrl-names = "default";
- pinctrl-0 = <&main_mdio1_pins_default
- &main_rgmii1_pins_default
- &main_rgmii2_pins_default>;
-};
-
-&cpsw_port1 {
- phy-mode = "rgmii-rxid";
- phy-handle = <&cpsw3g_phy0>;
+ pinctrl-0 = <&main_rgmii1_pins_default>, <&main_rgmii2_pins_default>;
};
&cpsw_port2 {
@@ -406,13 +192,6 @@
};
&cpsw3g_mdio {
- cpsw3g_phy0: ethernet-phy at 0 {
- reg = <0>;
- ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
- ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
- ti,min-output-impedance;
- };
-
cpsw3g_phy1: ethernet-phy at 1 {
reg = <1>;
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
@@ -429,6 +208,7 @@
};
&ospi0 {
+ status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&ospi0_pins_default>;
@@ -487,18 +267,6 @@
};
};
-&ecap0 {
- status = "disabled";
-};
-
-&ecap1 {
- status = "disabled";
-};
-
-&ecap2 {
- status = "disabled";
-};
-
-&main_mcan0 {
- status = "disabled";
+&tlv320aic3106 {
+ DVDD-supply = <&vcc_1v8>;
};
diff --git a/arch/arm/dts/k3-am625.dtsi b/arch/arm/dts/k3-am625.dtsi
index 887f31c23fef..4193c2b3eed6 100644
--- a/arch/arm/dts/k3-am625.dtsi
+++ b/arch/arm/dts/k3-am625.dtsi
@@ -48,6 +48,8 @@
d-cache-line-size = <64>;
d-cache-sets = <128>;
next-level-cache = <&L2_0>;
+ operating-points-v2 = <&a53_opp_table>;
+ clocks = <&k3_clks 135 0>;
};
cpu1: cpu at 1 {
@@ -62,6 +64,8 @@
d-cache-line-size = <64>;
d-cache-sets = <128>;
next-level-cache = <&L2_0>;
+ operating-points-v2 = <&a53_opp_table>;
+ clocks = <&k3_clks 136 0>;
};
cpu2: cpu at 2 {
@@ -76,6 +80,8 @@
d-cache-line-size = <64>;
d-cache-sets = <128>;
next-level-cache = <&L2_0>;
+ operating-points-v2 = <&a53_opp_table>;
+ clocks = <&k3_clks 137 0>;
};
cpu3: cpu at 3 {
@@ -90,13 +96,59 @@
d-cache-line-size = <64>;
d-cache-sets = <128>;
next-level-cache = <&L2_0>;
+ operating-points-v2 = <&a53_opp_table>;
+ clocks = <&k3_clks 138 0>;
+ };
+ };
+
+ a53_opp_table: opp-table {
+ compatible = "operating-points-v2-ti-cpu";
+ opp-shared;
+ syscon = <&wkup_conf>;
+
+ opp-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ opp-supported-hw = <0x01 0x0007>;
+ clock-latency-ns = <6000000>;
+ };
+
+ opp-400000000 {
+ opp-hz = /bits/ 64 <400000000>;
+ opp-supported-hw = <0x01 0x0007>;
+ clock-latency-ns = <6000000>;
+ };
+
+ opp-600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-supported-hw = <0x01 0x0007>;
+ clock-latency-ns = <6000000>;
+ };
+
+ opp-800000000 {
+ opp-hz = /bits/ 64 <800000000>;
+ opp-supported-hw = <0x01 0x0007>;
+ clock-latency-ns = <6000000>;
+ };
+
+ opp-1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-supported-hw = <0x01 0x0006>;
+ clock-latency-ns = <6000000>;
+ };
+
+ opp-1250000000 {
+ opp-hz = /bits/ 64 <1250000000>;
+ opp-supported-hw = <0x01 0x0004>;
+ clock-latency-ns = <6000000>;
+ opp-suspend;
};
};
L2_0: l2-cache0 {
compatible = "cache";
+ cache-unified;
cache-level = <2>;
- cache-size = <0x40000>;
+ cache-size = <0x80000>;
cache-line-size = <64>;
cache-sets = <512>;
};
diff --git a/arch/arm/dts/k3-am62x-sk-common.dtsi b/arch/arm/dts/k3-am62x-sk-common.dtsi
new file mode 100644
index 000000000000..34c8ffc553ec
--- /dev/null
+++ b/arch/arm/dts/k3-am62x-sk-common.dtsi
@@ -0,0 +1,412 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Common dtsi for AM62x SK and derivatives
+ *
+ * Copyright (C) 2021-2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include "k3-am625.dtsi"
+
+/ {
+ aliases {
+ serial2 = &main_uart0;
+ mmc0 = &sdhci0;
+ mmc1 = &sdhci1;
+ mmc2 = &sdhci2;
+ spi0 = &ospi0;
+ ethernet0 = &cpsw_port1;
+ ethernet1 = &cpsw_port2;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ };
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ memory at 80000000 {
+ device_type = "memory";
+ /* 2G RAM */
+ reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ ramoops at 9ca00000 {
+ compatible = "ramoops";
+ reg = <0x00 0x9ca00000 0x00 0x00100000>;
+ record-size = <0x8000>;
+ console-size = <0x8000>;
+ ftrace-size = <0x00>;
+ pmsg-size = <0x8000>;
+ };
+
+ secure_tfa_ddr: tfa at 9e780000 {
+ reg = <0x00 0x9e780000 0x00 0x80000>;
+ alignment = <0x1000>;
+ no-map;
+ };
+
+ secure_ddr: optee at 9e800000 {
+ reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
+ alignment = <0x1000>;
+ no-map;
+ };
+
+ wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory at 9db00000 {
+ compatible = "shared-dma-pool";
+ reg = <0x00 0x9db00000 0x00 0xc00000>;
+ no-map;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usr_led_pins_default>;
+
+ led-0 {
+ label = "am62-sk:green:heartbeat";
+ gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ function = LED_FUNCTION_HEARTBEAT;
+ default-state = "off";
+ };
+ };
+
+ tlv320_mclk: clk-0 {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <12288000>;
+ };
+
+ codec_audio: sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "AM62x-SKEVM";
+ simple-audio-card,widgets =
+ "Headphone", "Headphone Jack",
+ "Line", "Line In",
+ "Microphone", "Microphone Jack";
+ simple-audio-card,routing =
+ "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT",
+ "LINE1L", "Line In",
+ "LINE1R", "Line In",
+ "MIC3R", "Microphone Jack",
+ "Microphone Jack", "Mic Bias";
+ simple-audio-card,format = "dsp_b";
+ simple-audio-card,bitclock-master = <&sound_master>;
+ simple-audio-card,frame-master = <&sound_master>;
+ simple-audio-card,bitclock-inversion;
+
+ simple-audio-card,cpu {
+ sound-dai = <&mcasp1>;
+ };
+
+ sound_master: simple-audio-card,codec {
+ sound-dai = <&tlv320aic3106>;
+ clocks = <&tlv320_mclk>;
+ };
+ };
+};
+
+&main_pmx0 {
+ /* First pad number is ALW package and second is AMC package */
+ main_uart0_pins_default: main-uart0-default-pins {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x1c8, PIN_INPUT, 0) /* (D14/A13) UART0_RXD */
+ AM62X_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (E14/E11) UART0_TXD */
+ >;
+ };
+
+ main_uart1_pins_default: main-uart1-default-pins {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x194, PIN_INPUT, 2) /* (B19/B18) MCASP0_AXR3.UART1_CTSn */
+ AM62X_IOPAD(0x198, PIN_OUTPUT, 2) /* (A19/B17) MCASP0_AXR2.UART1_RTSn */
+ AM62X_IOPAD(0x1ac, PIN_INPUT, 2) /* (E19/D15) MCASP0_AFSR.UART1_RXD */
+ AM62X_IOPAD(0x1b0, PIN_OUTPUT, 2) /* (A20/D16) MCASP0_ACLKR.UART1_TXD */
+ >;
+ };
+
+ main_i2c0_pins_default: main-i2c0-default-pins {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x1e0, PIN_INPUT_PULLUP, 0) /* (B16/E12) I2C0_SCL */
+ AM62X_IOPAD(0x1e4, PIN_INPUT_PULLUP, 0) /* (A16/D14) I2C0_SDA */
+ >;
+ };
+
+ main_i2c1_pins_default: main-i2c1-default-pins {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17/A17) I2C1_SCL */
+ AM62X_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17/A16) I2C1_SDA */
+ >;
+ };
+
+ main_i2c2_pins_default: main-i2c2-default-pins {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x0b0, PIN_INPUT_PULLUP, 1) /* (K22/H18) GPMC0_CSn2.I2C2_SCL */
+ AM62X_IOPAD(0x0b4, PIN_INPUT_PULLUP, 1) /* (K24/H19) GPMC0_CSn3.I2C2_SDA */
+ >;
+ };
+
+ main_mmc0_pins_default: main-mmc0-default-pins {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x220, PIN_INPUT, 0) /* (Y3/V3) MMC0_CMD */
+ AM62X_IOPAD(0x218, PIN_INPUT, 0) /* (AB1/Y1) MMC0_CLK */
+ AM62X_IOPAD(0x214, PIN_INPUT, 0) /* (AA2/V2) MMC0_DAT0 */
+ AM62X_IOPAD(0x210, PIN_INPUT, 0) /* (AA1/V1) MMC0_DAT1 */
+ AM62X_IOPAD(0x20c, PIN_INPUT, 0) /* (AA3/W2) MMC0_DAT2 */
+ AM62X_IOPAD(0x208, PIN_INPUT, 0) /* (Y4/W1) MMC0_DAT3 */
+ AM62X_IOPAD(0x204, PIN_INPUT, 0) /* (AB2/Y2) MMC0_DAT4 */
+ AM62X_IOPAD(0x200, PIN_INPUT, 0) /* (AC1/W3) MMC0_DAT5 */
+ AM62X_IOPAD(0x1fc, PIN_INPUT, 0) /* (AD2/W4) MMC0_DAT6 */
+ AM62X_IOPAD(0x1f8, PIN_INPUT, 0) /* (AC2/V4) MMC0_DAT7 */
+ >;
+ };
+
+ main_mmc1_pins_default: main-mmc1-default-pins {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x23c, PIN_INPUT, 0) /* (A21/C18) MMC1_CMD */
+ AM62X_IOPAD(0x234, PIN_INPUT, 0) /* (B22/A20) MMC1_CLK */
+ AM62X_IOPAD(0x230, PIN_INPUT, 0) /* (A22/A19) MMC1_DAT0 */
+ AM62X_IOPAD(0x22c, PIN_INPUT, 0) /* (B21/B19) MMC1_DAT1 */
+ AM62X_IOPAD(0x228, PIN_INPUT, 0) /* (C21/B20) MMC1_DAT2 */
+ AM62X_IOPAD(0x224, PIN_INPUT, 0) /* (D22/C19) MMC1_DAT3 */
+ AM62X_IOPAD(0x240, PIN_INPUT, 0) /* (D17/C15) MMC1_SDCD */
+ >;
+ };
+
+ usr_led_pins_default: usr-led-default-pins {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x244, PIN_OUTPUT, 7) /* (C17/B15) MMC1_SDWP.GPIO1_49 */
+ >;
+ };
+
+ main_mdio1_pins_default: main-mdio1-default-pins {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x160, PIN_OUTPUT, 0) /* (AD24/V17) MDIO0_MDC */
+ AM62X_IOPAD(0x15c, PIN_INPUT, 0) /* (AB22/U16) MDIO0_MDIO */
+ >;
+ };
+
+ main_rgmii1_pins_default: main-rgmii1-default-pins {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x14c, PIN_INPUT, 0) /* (AB17/W15) RGMII1_RD0 */
+ AM62X_IOPAD(0x150, PIN_INPUT, 0) /* (AC17/Y16) RGMII1_RD1 */
+ AM62X_IOPAD(0x154, PIN_INPUT, 0) /* (AB16/AA17) RGMII1_RD2 */
+ AM62X_IOPAD(0x158, PIN_INPUT, 0) /* (AA15/Y15) RGMII1_RD3 */
+ AM62X_IOPAD(0x148, PIN_INPUT, 0) /* (AD17/AA16) RGMII1_RXC */
+ AM62X_IOPAD(0x144, PIN_INPUT, 0) /* (AE17/W14) RGMII1_RX_CTL */
+ AM62X_IOPAD(0x134, PIN_OUTPUT, 0) /* (AE20/U14) RGMII1_TD0 */
+ AM62X_IOPAD(0x138, PIN_OUTPUT, 0) /* (AD20/AA19) RGMII1_TD1 */
+ AM62X_IOPAD(0x13c, PIN_OUTPUT, 0) /* (AE18/Y17) RGMII1_TD2 */
+ AM62X_IOPAD(0x140, PIN_OUTPUT, 0) /* (AD18/AA18) RGMII1_TD3 */
+ AM62X_IOPAD(0x130, PIN_OUTPUT, 0) /* (AE19/W16) RGMII1_TXC */
+ AM62X_IOPAD(0x12c, PIN_OUTPUT, 0) /* (AD19/V15) RGMII1_TX_CTL */
+ >;
+ };
+
+ main_usb1_pins_default: main-usb1-default-pins {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x0258, PIN_OUTPUT, 0) /* (F18/E16) USB1_DRVVBUS */
+ >;
+ };
+
+ main_mcasp1_pins_default: main-mcasp1-default-pins {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x090, PIN_INPUT, 2) /* (M24/K17) GPMC0_BE0N_CLE.MCASP1_ACLKX */
+ AM62X_IOPAD(0x098, PIN_INPUT, 2) /* (U23/P21) GPMC0_WAIT0.MCASP1_AFSX */
+ AM62X_IOPAD(0x08c, PIN_OUTPUT, 2) /* (L25/J17) GPMC0_WEN.MCASP1_AXR0 */
+ AM62X_IOPAD(0x084, PIN_INPUT, 2) /* (L23/K20) GPMC0_ADVN_ALE.MCASP1_AXR2 */
+ >;
+ };
+};
+
+&mcu_pmx0 {
+ wkup_uart0_pins_default: wkup-uart0-default-pins {
+ pinctrl-single,pins = <
+ AM62X_MCU_IOPAD(0x02c, PIN_INPUT, 0) /* (C6/A7) WKUP_UART0_CTSn */
+ AM62X_MCU_IOPAD(0x030, PIN_OUTPUT, 0) /* (A4/B4) WKUP_UART0_RTSn */
+ AM62X_MCU_IOPAD(0x024, PIN_INPUT, 0) /* (B4/B5) WKUP_UART0_RXD */
+ AM62X_MCU_IOPAD(0x028, PIN_OUTPUT, 0) /* (C5/C6) WKUP_UART0_TXD */
+ >;
+ };
+};
+
+&wkup_uart0 {
+ /* WKUP UART0 is used by DM firmware */
+ status = "reserved";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wkup_uart0_pins_default>;
+};
+
+&main_uart0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_uart0_pins_default>;
+};
+
+&main_uart1 {
+ /* Main UART1 is used by TIFS firmware */
+ status = "reserved";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_uart1_pins_default>;
+};
+
+&main_i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+ clock-frequency = <400000>;
+
+ eeprom at 51 {
+ /* AT24C512C-MAHM-T or M24512-DFMC6TG */
+ compatible = "atmel,24c512";
+ reg = <0x51>;
+ };
+
+ typec_pd0: tps6598x at 3f {
+ compatible = "ti,tps6598x";
+ reg = <0x3f>;
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ self-powered;
+ data-role = "dual";
+ power-role = "sink";
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ usb_con_hs: endpoint {
+ remote-endpoint = <&usb0_hs_ep>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&main_i2c1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c1_pins_default>;
+ clock-frequency = <400000>;
+
+ tlv320aic3106: audio-codec at 1b {
+ #sound-dai-cells = <0>;
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+ ai3x-micbias-vg = <1>; /* 2.0V */
+
+ /* Regulators */
+ AVDD-supply = <&vcc_3v3_sys>;
+ IOVDD-supply = <&vcc_3v3_sys>;
+ DRVDD-supply = <&vcc_3v3_sys>;
+ };
+};
+
+&sdhci0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mmc0_pins_default>;
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
+};
+
+&sdhci1 {
+ /* SD/MMC */
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mmc1_pins_default>;
+ ti,driver-strength-ohm = <50>;
+ disable-wp;
+};
+
+&cpsw3g {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_rgmii1_pins_default>;
+};
+
+&cpsw_port1 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&cpsw3g_phy0>;
+};
+
+&cpsw3g_mdio {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mdio1_pins_default>;
+
+ cpsw3g_phy0: ethernet-phy at 0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+};
+
+&mailbox0_cluster0 {
+ mbox_m4_0: mbox-m4-0 {
+ ti,mbox-rx = <0 0 0>;
+ ti,mbox-tx = <1 0 0>;
+ };
+};
+
+&usbss0 {
+ status = "okay";
+ ti,vbus-divider;
+};
+
+&usbss1 {
+ status = "okay";
+ ti,vbus-divider;
+};
+
+&usb0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ usb-role-switch;
+
+ port at 0 {
+ reg = <0>;
+ usb0_hs_ep: endpoint {
+ remote-endpoint = <&usb_con_hs>;
+ };
+ };
+};
+
+&usb1 {
+ dr_mode = "host";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_usb1_pins_default>;
+};
+
+&mcasp1 {
+ status = "okay";
+ #sound-dai-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_mcasp1_pins_default>;
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 1 0 2 0
+ 0 0 0 0
+ 0 0 0 0
+ 0 0 0 0
+ >;
+ tx-num-evt = <32>;
+ rx-num-evt = <32>;
+};
diff --git a/arch/arm/dts/k3-pinctrl.h b/arch/arm/dts/k3-pinctrl.h
new file mode 100644
index 000000000000..c97548a3f42d
--- /dev/null
+++ b/arch/arm/dts/k3-pinctrl.h
@@ -0,0 +1,53 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * This header provides constants for pinctrl bindings for TI's K3 SoC
+ * family.
+ *
+ * Copyright (C) 2018-2023 Texas Instruments Incorporated - https://www.ti.com/
+ */
+#ifndef DTS_ARM64_TI_K3_PINCTRL_H
+#define DTS_ARM64_TI_K3_PINCTRL_H
+
+#define PULLUDEN_SHIFT (16)
+#define PULLTYPESEL_SHIFT (17)
+#define RXACTIVE_SHIFT (18)
+
+#define PULL_DISABLE (1 << PULLUDEN_SHIFT)
+#define PULL_ENABLE (0 << PULLUDEN_SHIFT)
+
+#define PULL_UP (1 << PULLTYPESEL_SHIFT | PULL_ENABLE)
+#define PULL_DOWN (0 << PULLTYPESEL_SHIFT | PULL_ENABLE)
+
+#define INPUT_EN (1 << RXACTIVE_SHIFT)
+#define INPUT_DISABLE (0 << RXACTIVE_SHIFT)
+
+/* Only these macros are expected be used directly in device tree files */
+#define PIN_OUTPUT (INPUT_DISABLE | PULL_DISABLE)
+#define PIN_OUTPUT_PULLUP (INPUT_DISABLE | PULL_UP)
+#define PIN_OUTPUT_PULLDOWN (INPUT_DISABLE | PULL_DOWN)
+#define PIN_INPUT (INPUT_EN | PULL_DISABLE)
+#define PIN_INPUT_PULLUP (INPUT_EN | PULL_UP)
+#define PIN_INPUT_PULLDOWN (INPUT_EN | PULL_DOWN)
+
+#define AM62AX_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM62AX_MCU_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define AM62X_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM62X_MCU_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define AM64X_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM64X_MCU_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define AM65X_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+#define AM65X_WKUP_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define J721E_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+#define J721E_WKUP_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define J721S2_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+#define J721S2_WKUP_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+
+#define J784S4_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+#define J784S4_WKUP_IOPAD(pa, val, muxmode) (((pa) & 0x1fff)) ((val) | (muxmode))
+
+#endif
--
2.40.0
More information about the U-Boot
mailing list