[PATCH 08/10] ARM: renesas: Add R8A77970 V3MSK board and CPLD code
Marek Vasut
marek.vasut+renesas at mailbox.org
Wed May 31 23:13:14 CEST 2023
From: Valentine Barshak <valentine.barshak at cogentembedded.com>
Add board code for the R8A77970 V3MSK board.
Add CPLD sysreset driver to the R-Car V3M SK board.
Extracted from a larger patch by Valentine Barshak.
Reviewed-by: Marek Vasut <marek.vasut+renesas at mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak at cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud at renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa at renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas at mailbox.org>
[Marek: Sync configs and board code with V3M Eagle, squash CPLD driver in]
---
arch/arm/dts/Makefile | 1 +
arch/arm/dts/r8a77970-v3msk-u-boot.dts | 65 +++++
arch/arm/mach-rmobile/Kconfig.rcar3 | 6 +
board/renesas/v3msk/Kconfig | 15 +
board/renesas/v3msk/MAINTAINERS | 6 +
board/renesas/v3msk/Makefile | 15 +
board/renesas/v3msk/cpld.c | 368 +++++++++++++++++++++++++
configs/r8a77970_v3msk_defconfig | 87 ++++++
doc/README.rmobile | 1 +
9 files changed, 564 insertions(+)
create mode 100644 arch/arm/dts/r8a77970-v3msk-u-boot.dts
create mode 100644 board/renesas/v3msk/Kconfig
create mode 100644 board/renesas/v3msk/MAINTAINERS
create mode 100644 board/renesas/v3msk/Makefile
create mode 100644 board/renesas/v3msk/cpld.c
create mode 100644 configs/r8a77970_v3msk_defconfig
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 480269fa606..95a7b234687 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -1053,6 +1053,7 @@ dtb-$(CONFIG_RCAR_GEN3) += \
r8a77965-ulcb-u-boot.dtb \
r8a77965-salvator-x-u-boot.dtb \
r8a77970-eagle-u-boot.dtb \
+ r8a77970-v3msk-u-boot.dtb \
r8a77980-condor-u-boot.dtb \
r8a77990-ebisu-u-boot.dtb \
r8a77995-draak-u-boot.dtb
diff --git a/arch/arm/dts/r8a77970-v3msk-u-boot.dts b/arch/arm/dts/r8a77970-v3msk-u-boot.dts
new file mode 100644
index 00000000000..6ee06d7c000
--- /dev/null
+++ b/arch/arm/dts/r8a77970-v3msk-u-boot.dts
@@ -0,0 +1,65 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source extras for U-Boot for the V3MSK board
+ *
+ * Copyright (C) 2019 Cogent Embedded, Inc.
+ */
+
+#include "r8a77970-v3msk.dts"
+#include "r8a77970-u-boot.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ aliases {
+ spi0 = &rpc;
+ };
+
+ cpld {
+ compatible = "renesas,v3msk-cpld";
+ status = "okay";
+ gpio-mdc = <&gpio1 21 0>;
+ gpio-mosi = <&gpio1 22 0>;
+ gpio-miso = <&gpio1 23 0>;
+ gpio-enablez = <&gpio1 19 0>;
+ /* Disable V3MSK Videobox Mini CANFD PHY */
+ gpios = <&gpio0 12 0>, <&gpio0 14 0>;
+ };
+};
+
+&avb {
+ pinctrl-0 = <&avb0_pins>;
+ pinctrl-names = "default";
+
+};
+
+&phy0 {
+ reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+};
+
+&pfc {
+ avb0_pins: avb {
+ mux {
+ groups = "avb0_link", "avb0_mdio", "avb0_rgmii", "avb0_txcrefclk";
+ function = "avb0";
+ };
+ };
+};
+
+&rpc {
+ num-cs = <1>;
+ status = "okay";
+ spi-max-frequency = <50000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ flash0: spi-flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "s25fs512s", "spi-flash", "jedec,spi-nor";
+ spi-max-frequency = <50000000>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <1>;
+ reg = <0>;
+ status = "okay";
+ };
+};
diff --git a/arch/arm/mach-rmobile/Kconfig.rcar3 b/arch/arm/mach-rmobile/Kconfig.rcar3
index 5f338219b45..46d274273af 100644
--- a/arch/arm/mach-rmobile/Kconfig.rcar3
+++ b/arch/arm/mach-rmobile/Kconfig.rcar3
@@ -111,6 +111,11 @@ config TARGET_EAGLE
help
Support for Renesas R-Car Gen3 Eagle platform
+config TARGET_V3MSK
+ bool "V3MSK board"
+ help
+ Support for Renesas R-Car Gen3 V3MSK platform
+
config TARGET_EBISU
bool "Ebisu board"
imply R8A77990
@@ -166,6 +171,7 @@ source "board/renesas/eagle/Kconfig"
source "board/renesas/ebisu/Kconfig"
source "board/renesas/salvator-x/Kconfig"
source "board/renesas/ulcb/Kconfig"
+source "board/renesas/v3msk/Kconfig"
source "board/beacon/beacon-rzg2m/Kconfig"
source "board/hoperun/hihope-rzg2/Kconfig"
source "board/silinux/ek874/Kconfig"
diff --git a/board/renesas/v3msk/Kconfig b/board/renesas/v3msk/Kconfig
new file mode 100644
index 00000000000..fe037fd98f0
--- /dev/null
+++ b/board/renesas/v3msk/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_V3MSK
+
+config SYS_SOC
+ default "rmobile"
+
+config SYS_BOARD
+ default "v3msk"
+
+config SYS_VENDOR
+ default "renesas"
+
+config SYS_CONFIG_NAME
+ default "rcar-gen3-common"
+
+endif
diff --git a/board/renesas/v3msk/MAINTAINERS b/board/renesas/v3msk/MAINTAINERS
new file mode 100644
index 00000000000..12822a4571a
--- /dev/null
+++ b/board/renesas/v3msk/MAINTAINERS
@@ -0,0 +1,6 @@
+V3MSK BOARD
+M: Cogent Embedded, Inc. <source at cogentembedded.com>
+S: Maintained
+F: board/renesas/v3msk/
+F: include/configs/v3msk.h
+F: configs/r8a77970_v3msk_defconfig
diff --git a/board/renesas/v3msk/Makefile b/board/renesas/v3msk/Makefile
new file mode 100644
index 00000000000..ec493e572f1
--- /dev/null
+++ b/board/renesas/v3msk/Makefile
@@ -0,0 +1,15 @@
+#
+# board/renesas/v3msk/Makefile
+#
+# Copyright (C) 2019 Renesas Electronics Corporation
+# Copyright (C) 2019 Cogent Embedded, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+ifdef CONFIG_SPL_BUILD
+obj-y := ../rcar-common/gen3-spl.o
+else
+obj-y := ../rcar-common/v3-common.o ../rcar-common/common.o
+obj-$(CONFIG_SYSRESET) += cpld.o
+endif
diff --git a/board/renesas/v3msk/cpld.c b/board/renesas/v3msk/cpld.c
new file mode 100644
index 00000000000..aed616ac859
--- /dev/null
+++ b/board/renesas/v3msk/cpld.c
@@ -0,0 +1,368 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * V3MSK board CPLD access support
+ *
+ * Copyright (C) 2019 Renesas Electronics Corporation
+ * Copyright (C) 2019 Cogent Embedded, Inc.
+ *
+ */
+
+#include <common.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
+#include <dm.h>
+#include <errno.h>
+#include <linux/err.h>
+#include <sysreset.h>
+#include <linux/delay.h>
+#include <command.h>
+
+#define CPLD_ADDR_PRODUCT_L 0x000 /* R */
+#define CPLD_ADDR_PRODUCT_H 0x001 /* R */
+#define CPLD_ADDR_CPLD_VERSION_D 0x002 /* R */
+#define CPLD_ADDR_CPLD_VERSION_Y 0x003 /* R */
+#define CPLD_ADDR_MODE_SET_L 0x004 /* R/W */
+#define CPLD_ADDR_MODE_SET_H 0x005 /* R/W */
+#define CPLD_ADDR_MODE_APPLIED_L 0x006 /* R */
+#define CPLD_ADDR_MODE_APPLIED_H 0x007 /* R */
+#define CPLD_ADDR_DIPSW 0x008 /* R */
+#define CPLD_ADDR_RESET 0x00A /* R/W */
+#define CPLD_ADDR_POWER_CFG 0x00B /* R/W */
+#define CPLD_ADDR_PERI_CFG1 0x00C /* R/W */
+#define CPLD_ADDR_PERI_CFG2 0x00D /* R/W */
+#define CPLD_ADDR_LEDS 0x00E /* R/W */
+#define CPLD_ADDR_PCB_VERSION 0x300 /* R */
+#define CPLD_ADDR_SOC_VERSION 0x301 /* R */
+#define CPLD_ADDR_PCB_SN_L 0x302 /* R */
+#define CPLD_ADDR_PCB_SN_H 0x303 /* R */
+
+#define MDIO_DELAY 10 /* microseconds */
+
+#define CPLD_MAX_GPIOS 2
+
+struct renesas_v3msk_sysreset_priv {
+ struct gpio_desc miso;
+ struct gpio_desc mosi;
+ struct gpio_desc mdc;
+ struct gpio_desc enablez;
+ /*
+ * V3MSK Videobox Mini board has CANFD PHY connected
+ * we must shutdown this chip to use bb pins
+ */
+ struct gpio_desc gpios[CPLD_MAX_GPIOS];
+};
+
+static void mdio_bb_active_mdio(struct renesas_v3msk_sysreset_priv *priv)
+{
+ dm_gpio_set_dir_flags(&priv->mosi, GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
+}
+
+static void mdio_bb_tristate_mdio(struct renesas_v3msk_sysreset_priv *priv)
+{
+ dm_gpio_set_dir_flags(&priv->mosi, GPIOD_IS_IN);
+}
+
+static void mdio_bb_set_mdio(struct renesas_v3msk_sysreset_priv *priv, int val)
+{
+ dm_gpio_set_value(&priv->mosi, val);
+}
+
+static int mdio_bb_get_mdio(struct renesas_v3msk_sysreset_priv *priv)
+{
+ return dm_gpio_get_value(&priv->miso);
+}
+
+static void mdio_bb_set_mdc(struct renesas_v3msk_sysreset_priv *priv, int val)
+{
+ dm_gpio_set_value(&priv->mdc, val);
+}
+
+static void mdio_bb_delay(void)
+{
+ udelay(MDIO_DELAY);
+}
+
+/* Send the preamble, address, and register (common to read and write) */
+static void mdio_bb_pre(struct renesas_v3msk_sysreset_priv *priv,
+ u8 op, u8 addr, u8 reg)
+{
+ int i;
+
+ /* 32-bit preamble */
+ mdio_bb_active_mdio(priv);
+ mdio_bb_set_mdio(priv, 1);
+ for (i = 0; i < 32; i++) {
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+ }
+ /* send the ST (2-bits of '01') */
+ mdio_bb_set_mdio(priv, 0);
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+ mdio_bb_set_mdio(priv, 1);
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+ /* send the OP (2-bits of Opcode: '10'-read, '01'-write) */
+ mdio_bb_set_mdio(priv, op >> 1);
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+ mdio_bb_set_mdio(priv, op & 1);
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+ /* send the PA5 (5-bits of PHY address) */
+ for (i = 0; i < 5; i++) {
+ mdio_bb_set_mdio(priv, addr & 0x10); /* MSB first */
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+ addr <<= 1;
+ }
+ /* send the RA5 (5-bits of register address) */
+ for (i = 0; i < 5; i++) {
+ mdio_bb_set_mdio(priv, reg & 0x10); /* MSB first */
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+ reg <<= 1;
+ }
+}
+
+static int mdio_bb_read(struct renesas_v3msk_sysreset_priv *priv,
+ u8 addr, u8 reg)
+{
+ int i;
+ u16 data = 0;
+
+ mdio_bb_pre(priv, 2, addr, reg);
+ /* tri-state MDIO */
+ mdio_bb_tristate_mdio(priv);
+ /* read TA (2-bits of turn-around, last bit must be '0') */
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+ /* check the turnaround bit: the PHY should drive line to zero */
+ if (mdio_bb_get_mdio(priv) != 0) {
+ printf("PHY didn't drive TA low\n");
+ for (i = 0; i < 32; i++) {
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+ }
+ /* There is no PHY, set value to 0xFFFF */
+ return 0xFFFF;
+ }
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ /* read 16-bits of data */
+ for (i = 0; i < 16; i++) {
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+ data <<= 1;
+ data |= mdio_bb_get_mdio(priv);
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ }
+
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+
+ debug("cpld_read(0x%x) @ 0x%x = 0x%04x\n", reg, addr, data);
+
+ return data;
+}
+
+static void mdio_bb_write(struct renesas_v3msk_sysreset_priv *priv,
+ u8 addr, u8 reg, u16 val)
+{
+ int i;
+
+ mdio_bb_pre(priv, 1, addr, reg);
+ /* send the TA (2-bits of turn-around '10') */
+ mdio_bb_set_mdio(priv, 1);
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+ mdio_bb_set_mdio(priv, 0);
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+ /* write 16-bits of data */
+ for (i = 0; i < 16; i++) {
+ mdio_bb_set_mdio(priv, val & 0x8000); /* MSB first */
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+ val <<= 1;
+ }
+ /* tri-state MDIO */
+ mdio_bb_tristate_mdio(priv);
+ mdio_bb_set_mdc(priv, 0);
+ mdio_bb_delay();
+ mdio_bb_set_mdc(priv, 1);
+ mdio_bb_delay();
+}
+
+static u16 cpld_read(struct udevice *dev, u16 addr)
+{
+ struct renesas_v3msk_sysreset_priv *priv = dev_get_priv(dev);
+
+ /* random flash reads require 2 reads: first read is unreliable */
+ if (addr >= CPLD_ADDR_PCB_VERSION)
+ mdio_bb_read(priv, addr >> 5, addr & 0x1f);
+
+ return mdio_bb_read(priv, addr >> 5, addr & 0x1f);
+}
+
+static void cpld_write(struct udevice *dev, u16 addr, u16 data)
+{
+ struct renesas_v3msk_sysreset_priv *priv = dev_get_priv(dev);
+
+ mdio_bb_write(priv, addr >> 5, addr & 0x1f, data);
+}
+
+static int do_cpld(struct cmd_tbl *cmdtp, int flag, int argc, char * const argv[])
+{
+ struct udevice *dev;
+ u16 addr, val;
+ int ret;
+
+ ret = uclass_get_device_by_driver(UCLASS_SYSRESET,
+ DM_DRIVER_GET(sysreset_renesas_v3msk),
+ &dev);
+ if (ret)
+ return ret;
+
+ if (argc == 2 && strcmp(argv[1], "info") == 0) {
+ printf("Product: 0x%08x\n",
+ (cpld_read(dev, CPLD_ADDR_PRODUCT_H) << 16) |
+ cpld_read(dev, CPLD_ADDR_PRODUCT_L));
+ printf("CPLD version: 0x%08x\n",
+ (cpld_read(dev, CPLD_ADDR_CPLD_VERSION_Y) << 16) |
+ cpld_read(dev, CPLD_ADDR_CPLD_VERSION_D));
+ printf("Mode setting (MD0..26): 0x%08x\n",
+ (cpld_read(dev, CPLD_ADDR_MODE_APPLIED_H) << 16) |
+ cpld_read(dev, CPLD_ADDR_MODE_APPLIED_L));
+ printf("DIPSW (SW4, SW5): 0x%02x, 0x%x\n",
+ (cpld_read(dev, CPLD_ADDR_DIPSW) & 0xff) ^ 0xff,
+ (cpld_read(dev, CPLD_ADDR_DIPSW) >> 8) ^ 0xf);
+ printf("Power config: 0x%08x\n",
+ cpld_read(dev, CPLD_ADDR_POWER_CFG));
+ printf("Periferals config: 0x%08x\n",
+ (cpld_read(dev, CPLD_ADDR_PERI_CFG2) << 16) |
+ cpld_read(dev, CPLD_ADDR_PERI_CFG1));
+ printf("PCB version: %d.%d\n",
+ cpld_read(dev, CPLD_ADDR_PCB_VERSION) >> 8,
+ cpld_read(dev, CPLD_ADDR_PCB_VERSION) & 0xff);
+ printf("SOC version: %d.%d\n",
+ cpld_read(dev, CPLD_ADDR_SOC_VERSION) >> 8,
+ cpld_read(dev, CPLD_ADDR_SOC_VERSION) & 0xff);
+ printf("PCB S/N: %d\n",
+ (cpld_read(dev, CPLD_ADDR_PCB_SN_H) << 16) |
+ cpld_read(dev, CPLD_ADDR_PCB_SN_L));
+ return 0;
+ }
+
+ if (argc < 3)
+ return CMD_RET_USAGE;
+
+ addr = simple_strtoul(argv[2], NULL, 16);
+ if (!(addr >= CPLD_ADDR_PRODUCT_L && addr <= CPLD_ADDR_LEDS)) {
+ printf("cpld invalid addr\n");
+ return CMD_RET_USAGE;
+ }
+
+ if (argc == 3 && strcmp(argv[1], "read") == 0) {
+ printf("0x%x\n", cpld_read(dev, addr));
+ } else if (argc == 4 && strcmp(argv[1], "write") == 0) {
+ val = simple_strtoul(argv[3], NULL, 16);
+ cpld_write(dev, addr, val);
+ }
+
+ return 0;
+}
+
+U_BOOT_CMD(cpld, 4, 1, do_cpld,
+ "CPLD access",
+ "info\n"
+ "cpld read addr\n"
+ "cpld write addr val\n"
+);
+
+static int renesas_v3msk_sysreset_request(struct udevice *dev, enum sysreset_t type)
+{
+ cpld_write(dev, CPLD_ADDR_RESET, 1);
+
+ return -EINPROGRESS;
+}
+
+static int renesas_v3msk_sysreset_probe(struct udevice *dev)
+{
+ struct renesas_v3msk_sysreset_priv *priv = dev_get_priv(dev);
+
+ if (gpio_request_by_name(dev, "gpio-miso", 0, &priv->miso,
+ GPIOD_IS_IN))
+ return -EINVAL;
+
+ if (gpio_request_by_name(dev, "gpio-mosi", 0, &priv->mosi,
+ GPIOD_IS_OUT))
+ return -EINVAL;
+
+ if (gpio_request_by_name(dev, "gpio-mdc", 0, &priv->mdc,
+ GPIOD_IS_OUT))
+ return -EINVAL;
+
+ if (gpio_request_by_name(dev, "gpio-enablez", 0, &priv->enablez,
+ GPIOD_IS_OUT))
+ return -EINVAL;
+
+ /* V3MSK Videobox Mini board has CANFD PHY connected
+ * we must shutdown this chip to use bb pins
+ */
+ gpio_request_list_by_name(dev, "gpios", priv->gpios, CPLD_MAX_GPIOS,
+ GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
+
+ return 0;
+}
+
+static struct sysreset_ops renesas_v3msk_sysreset = {
+ .request = renesas_v3msk_sysreset_request,
+};
+
+static const struct udevice_id renesas_v3msk_sysreset_ids[] = {
+ { .compatible = "renesas,v3msk-cpld" },
+ { /* sentinel */ }
+};
+
+U_BOOT_DRIVER(sysreset_renesas_v3msk) = {
+ .name = "renesas_v3msk_sysreset",
+ .id = UCLASS_SYSRESET,
+ .ops = &renesas_v3msk_sysreset,
+ .probe = renesas_v3msk_sysreset_probe,
+ .of_match = renesas_v3msk_sysreset_ids,
+ .priv_auto = sizeof(struct renesas_v3msk_sysreset_priv),
+};
diff --git a/configs/r8a77970_v3msk_defconfig b/configs/r8a77970_v3msk_defconfig
new file mode 100644
index 00000000000..74a140a8a2a
--- /dev/null
+++ b/configs/r8a77970_v3msk_defconfig
@@ -0,0 +1,87 @@
+CONFIG_ARM=y
+CONFIG_COUNTER_FREQUENCY=16666666
+CONFIG_ARCH_CPU_INIT=y
+CONFIG_ARCH_RMOBILE=y
+CONFIG_TEXT_BASE=0x50000000
+CONFIG_SYS_MALLOC_LEN=0x4000000
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_ENV_SIZE=0x40000
+CONFIG_ENV_OFFSET=0x700000
+CONFIG_ENV_SECT_SIZE=0x40000
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="r8a77970-v3msk-u-boot"
+CONFIG_SPL_TEXT_BASE=0xe6318000
+CONFIG_RCAR_GEN3=y
+CONFIG_R8A77970=y
+CONFIG_TARGET_V3MSK=y
+CONFIG_SPL_STACK=0xe6304000
+CONFIG_SYS_LOAD_ADDR=0x58000000
+CONFIG_LTO=y
+CONFIG_REMAKE_ELF=y
+CONFIG_SYS_MONITOR_LEN=1048576
+CONFIG_FIT=y
+# CONFIG_ARCH_FIXUP_FDT_MEMORY is not set
+CONFIG_SUPPORT_RAW_INITRD=y
+CONFIG_USE_BOOTARGS=y
+CONFIG_DEFAULT_FDT_FILE="r8a77970-v3msk.dtb"
+CONFIG_SYS_MALLOC_BOOTPARAMS=y
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0xe631f000
+CONFIG_SPL_BSS_MAX_SIZE=0x1000
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_HUSH_PARSER=y
+CONFIG_SYS_MAXARGS=64
+CONFIG_SYS_PBSIZE=2068
+CONFIG_CMD_BOOTZ=y
+CONFIG_CMD_DFU=y
+CONFIG_CMD_ASKENV=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_OF_CONTROL=y
+CONFIG_OF_DTB_PROPS_REMOVE=y
+CONFIG_OF_REMOVE_PROPS="dmas dma-names interrupt-parent interrupts interrupts-extended interrupt-names interrupt-map interrupt-map-mask iommus"
+CONFIG_ENV_OVERWRITE=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_VERSION_VARIABLE=y
+CONFIG_REGMAP=y
+CONFIG_SYSCON=y
+CONFIG_CLK=y
+CONFIG_CLK_RENESAS=y
+CONFIG_DFU_TFTP=y
+CONFIG_DFU_RAM=y
+CONFIG_DFU_SF=y
+CONFIG_RCAR_GPIO=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_RCAR_I2C=y
+CONFIG_MMC_IO_VOLTAGE=y
+CONFIG_MMC_UHS_SUPPORT=y
+CONFIG_MMC_HS200_SUPPORT=y
+CONFIG_RENESAS_SDHI=y
+CONFIG_MTD=y
+CONFIG_DM_SPI_FLASH=y
+CONFIG_SPI_FLASH_SPANSION=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_BITBANGMII=y
+CONFIG_BITBANGMII_MULTI=y
+CONFIG_PHY_MICREL=y
+CONFIG_PHY_MICREL_KSZ90X1=y
+CONFIG_RENESAS_RAVB=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_SCIF_CONSOLE=y
+CONFIG_SPI=y
+CONFIG_DM_SPI=y
+CONFIG_RENESAS_RPC_SPI=y
+CONFIG_SYSRESET=y
diff --git a/doc/README.rmobile b/doc/README.rmobile
index ea170a25a69..524d839558b 100644
--- a/doc/README.rmobile
+++ b/doc/README.rmobile
@@ -35,6 +35,7 @@ Currently the following boards are supported:
| R8A77965 M3-N | Renesas Electronics ULCB | r8a77965_ulcb
|---------------+----------------------------------------+-------------------
| R8A77970 V3M | Renesas Electronics Eagle | r8a77970_eagle_defconfig
+| R8A77970 V3M | Renesas Electronics V3MSK | r8a77970_v3msk_defconfig
|---------------+----------------------------------------+-------------------
| R8A77995 D3 | Renesas Electronics Draak | r8a77995_draak_defconfig
'===============+========================================+===================
--
2.39.2
More information about the U-Boot
mailing list