[PATCH v3 6/7] clk/qcom: add mnd_width to clk_rcg_set_rate_mnd()
Caleb Connolly
caleb.connolly at linaro.org
Fri Nov 3 16:39:30 CET 2023
This property is needed on some platforms to ensure that only the
relevant bits are set in the M/N/D registers.
Signed-off-by: Caleb Connolly <caleb.connolly at linaro.org>
Reviewed-by: Sumit Garg <sumit.garg at linaro.org>
---
drivers/clk/qcom/clock-apq8016.c | 4 ++--
drivers/clk/qcom/clock-apq8096.c | 4 ++--
drivers/clk/qcom/clock-qcom.c | 11 +++++++----
drivers/clk/qcom/clock-qcom.h | 2 +-
drivers/clk/qcom/clock-qcs404.c | 18 +++++++++---------
drivers/clk/qcom/clock-sdm845.c | 3 +--
6 files changed, 22 insertions(+), 20 deletions(-)
diff --git a/drivers/clk/qcom/clock-apq8016.c b/drivers/clk/qcom/clock-apq8016.c
index 3f44252c453e..630619c83454 100644
--- a/drivers/clk/qcom/clock-apq8016.c
+++ b/drivers/clk/qcom/clock-apq8016.c
@@ -86,7 +86,7 @@ static int clk_init_sdc(struct msm_clk_priv *priv, int slot, uint rate)
clk_enable_cbc(priv->base + SDCC_AHB_CBCR(slot));
/* 800Mhz/div, gpll0 */
clk_rcg_set_rate_mnd(priv->base, &sdc_regs[slot], div, 0, 0,
- CFG_CLK_SRC_GPLL0);
+ CFG_CLK_SRC_GPLL0, 8);
clk_enable_gpll0(priv->base, &gpll0_vote_clk);
clk_enable_cbc(priv->base + SDCC_APPS_CBCR(slot));
@@ -109,7 +109,7 @@ static int clk_init_uart(struct msm_clk_priv *priv)
/* 7372800 uart block clock @ GPLL0 */
clk_rcg_set_rate_mnd(priv->base, &uart2_regs, 1, 144, 15625,
- CFG_CLK_SRC_GPLL0);
+ CFG_CLK_SRC_GPLL0, 8);
/* Vote for gpll0 clock */
clk_enable_gpll0(priv->base, &gpll0_vote_clk);
diff --git a/drivers/clk/qcom/clock-apq8096.c b/drivers/clk/qcom/clock-apq8096.c
index 75633a7c2af8..095c1b431245 100644
--- a/drivers/clk/qcom/clock-apq8096.c
+++ b/drivers/clk/qcom/clock-apq8096.c
@@ -69,7 +69,7 @@ static int clk_init_sdc(struct msm_clk_priv *priv, uint rate)
clk_enable_cbc(priv->base + SDCC2_AHB_CBCR);
clk_rcg_set_rate_mnd(priv->base, &sdc_regs, div, 0, 0,
- CFG_CLK_SRC_GPLL0);
+ CFG_CLK_SRC_GPLL0, 8);
clk_enable_gpll0(priv->base, &gpll0_vote_clk);
clk_enable_cbc(priv->base + SDCC2_APPS_CBCR);
@@ -91,7 +91,7 @@ static int clk_init_uart(struct msm_clk_priv *priv)
/* 7372800 uart block clock @ GPLL0 */
clk_rcg_set_rate_mnd(priv->base, &uart2_regs, 1, 192, 15625,
- CFG_CLK_SRC_GPLL0);
+ CFG_CLK_SRC_GPLL0, 8);
/* Vote for gpll0 clock */
clk_enable_gpll0(priv->base, &gpll0_vote_clk);
diff --git a/drivers/clk/qcom/clock-qcom.c b/drivers/clk/qcom/clock-qcom.c
index 77bcaacd1583..fc478554f982 100644
--- a/drivers/clk/qcom/clock-qcom.c
+++ b/drivers/clk/qcom/clock-qcom.c
@@ -83,7 +83,7 @@ void clk_bcr_update(phys_addr_t apps_cmd_rcgr)
/* root set rate for clocks with half integer and MND divider */
void clk_rcg_set_rate_mnd(phys_addr_t base, const struct bcr_regs *regs,
- int div, int m, int n, int source)
+ int div, int m, int n, int source, u8 mnd_width)
{
u32 cfg;
/* M value for MND divider. */
@@ -92,11 +92,14 @@ void clk_rcg_set_rate_mnd(phys_addr_t base, const struct bcr_regs *regs,
u32 n_val = ~((n) - (m)) * !!(n);
/* NOT 2D value for MND divider. */
u32 d_val = ~(n);
+ u32 mask = BIT(mnd_width) - 1;
+
+ debug("m %#x n %#x d %#x div %#x mask %#x\n", m_val, n_val, d_val, div, mask);
/* Program MND values */
- writel(m_val, base + regs->M);
- writel(n_val, base + regs->N);
- writel(d_val, base + regs->D);
+ writel(m_val & mask, base + regs->M);
+ writel(n_val & mask, base + regs->N);
+ writel(d_val & mask, base + regs->D);
/* setup src select and divider */
cfg = readl(base + regs->cfg_rcgr);
diff --git a/drivers/clk/qcom/clock-qcom.h b/drivers/clk/qcom/clock-qcom.h
index 86f9ff6eb2f6..24a32cb9666d 100644
--- a/drivers/clk/qcom/clock-qcom.h
+++ b/drivers/clk/qcom/clock-qcom.h
@@ -72,7 +72,7 @@ void clk_bcr_update(phys_addr_t apps_cmd_rgcr);
void clk_enable_cbc(phys_addr_t cbcr);
void clk_enable_vote_clk(phys_addr_t base, const struct vote_clk *vclk);
void clk_rcg_set_rate_mnd(phys_addr_t base, const struct bcr_regs *regs,
- int div, int m, int n, int source);
+ int div, int m, int n, int source, u8 mnd_width);
void clk_rcg_set_rate(phys_addr_t base, const struct bcr_regs *regs, int div,
int source);
diff --git a/drivers/clk/qcom/clock-qcs404.c b/drivers/clk/qcom/clock-qcs404.c
index 9ad580b50fc8..921abf1f699b 100644
--- a/drivers/clk/qcom/clock-qcs404.c
+++ b/drivers/clk/qcom/clock-qcs404.c
@@ -195,7 +195,7 @@ static ulong qcs404_clk_set_rate(struct clk *clk, ulong rate)
case GCC_BLSP1_UART2_APPS_CLK:
/* UART: 115200 */
clk_rcg_set_rate_mnd(priv->base, &uart2_regs, 0, 12, 125,
- CFG_CLK_SRC_CXO);
+ CFG_CLK_SRC_CXO, 8);
clk_enable_cbc(priv->base + BLSP1_UART2_APPS_CBCR);
break;
case GCC_BLSP1_AHB_CLK:
@@ -204,7 +204,7 @@ static ulong qcs404_clk_set_rate(struct clk *clk, ulong rate)
case GCC_SDCC1_APPS_CLK:
/* SDCC1: 200MHz */
clk_rcg_set_rate_mnd(priv->base, &sdc_regs, 4, 0, 0,
- CFG_CLK_SRC_GPLL0);
+ CFG_CLK_SRC_GPLL0, 8);
clk_enable_gpll0(priv->base, &gpll0_vote_clk);
clk_enable_cbc(priv->base + SDCC_APPS_CBCR(1));
break;
@@ -214,16 +214,16 @@ static ulong qcs404_clk_set_rate(struct clk *clk, ulong rate)
case GCC_ETH_RGMII_CLK:
if (rate == 250000000)
clk_rcg_set_rate_mnd(priv->base, &emac_regs, 2, 0, 0,
- CFG_CLK_SRC_GPLL1);
+ CFG_CLK_SRC_GPLL1, 8);
else if (rate == 125000000)
clk_rcg_set_rate_mnd(priv->base, &emac_regs, 4, 0, 0,
- CFG_CLK_SRC_GPLL1);
+ CFG_CLK_SRC_GPLL1, 8);
else if (rate == 50000000)
clk_rcg_set_rate_mnd(priv->base, &emac_regs, 10, 0, 0,
- CFG_CLK_SRC_GPLL1);
+ CFG_CLK_SRC_GPLL1, 8);
else if (rate == 5000000)
clk_rcg_set_rate_mnd(priv->base, &emac_regs, 2, 1, 50,
- CFG_CLK_SRC_GPLL1);
+ CFG_CLK_SRC_GPLL1, 8);
break;
default:
return 0;
@@ -240,7 +240,7 @@ static int qcs404_clk_enable(struct clk *clk)
case GCC_USB30_MASTER_CLK:
clk_enable_cbc(priv->base + USB30_MASTER_CBCR);
clk_rcg_set_rate_mnd(priv->base, &usb30_master_regs, 4, 0, 0,
- CFG_CLK_SRC_GPLL0);
+ CFG_CLK_SRC_GPLL0, 8);
break;
case GCC_SYS_NOC_USB3_CLK:
clk_enable_cbc(priv->base + SYS_NOC_USB3_CBCR);
@@ -262,14 +262,14 @@ static int qcs404_clk_enable(struct clk *clk)
clk_enable_cbc(priv->base + ETH_PTP_CBCR);
clk_enable_gpll0(priv->base, &gpll1_vote_clk);
clk_rcg_set_rate_mnd(priv->base, &emac_ptp_regs, 2, 0, 0,
- CFG_CLK_SRC_GPLL1);
+ CFG_CLK_SRC_GPLL1, 8);
break;
case GCC_ETH_RGMII_CLK:
/* SPEED_1000: freq -> 250MHz */
clk_enable_cbc(priv->base + ETH_RGMII_CBCR);
clk_enable_gpll0(priv->base, &gpll1_vote_clk);
clk_rcg_set_rate_mnd(priv->base, &emac_regs, 2, 0, 0,
- CFG_CLK_SRC_GPLL1);
+ CFG_CLK_SRC_GPLL1, 8);
break;
case GCC_ETH_SLAVE_AHB_CLK:
clk_enable_cbc(priv->base + ETH_SLAVE_AHB_CBCR);
diff --git a/drivers/clk/qcom/clock-sdm845.c b/drivers/clk/qcom/clock-sdm845.c
index fc9a783f7354..6af1f38302d2 100644
--- a/drivers/clk/qcom/clock-sdm845.c
+++ b/drivers/clk/qcom/clock-sdm845.c
@@ -89,8 +89,7 @@ static ulong sdm845_clk_set_rate(struct clk *clk, ulong rate)
case GCC_QUPV3_WRAP1_S1_CLK: /* UART9 */
freq = qcom_find_freq(ftbl_gcc_qupv3_wrap0_s0_clk_src, rate);
clk_rcg_set_rate_mnd(priv->base, &uart2_regs,
- freq->pre_div, freq->m, freq->n, freq->src);
-
+ freq->pre_div, freq->m, freq->n, freq->src, 16);
return freq->freq;
default:
return 0;
--
2.42.0
More information about the U-Boot
mailing list