[PATCH v5 32/38] mmc: exynos_dw_mmc: Pull all init code into probe function

Sam Protsenko semen.protsenko at linaro.org
Thu Aug 8 05:14:38 CEST 2024


There is no logical sense to split the initialization code between
multiple functions. Pull both do_dwmci_init() and
exynos_dwmci_core_init() into exynos_dwmmc_probe() to make the code more
simple and obvious.

No functional change.

Signed-off-by: Sam Protsenko <semen.protsenko at linaro.org>
---
Changes in v5:
  - (none)

Changes in v4:
  - (none)

Changes in v3:
  - (none)

Changes in v2:
  - Replaced CONFIG_IS_ENABLED() with #ifdef

 drivers/mmc/exynos_dw_mmc.c | 86 +++++++++++++++----------------------
 1 file changed, 35 insertions(+), 51 deletions(-)

diff --git a/drivers/mmc/exynos_dw_mmc.c b/drivers/mmc/exynos_dw_mmc.c
index 29241edf7915..41fb32c579ef 100644
--- a/drivers/mmc/exynos_dw_mmc.c
+++ b/drivers/mmc/exynos_dw_mmc.c
@@ -209,55 +209,6 @@ static void exynos_dwmci_board_init(struct dwmci_host *host)
 		exynos_dwmci_clksel(host);
 }
 
-static int exynos_dwmci_core_init(struct dwmci_host *host)
-{
-	unsigned long freq;
-	int err;
-
-	if (host->bus_hz)
-		freq = host->bus_hz;
-	else
-		freq = DWMMC_MAX_FREQ;
-
-	err = exynos_dwmmc_set_sclk(host, freq);
-	if (err) {
-		printf("DWMMC%d: failed to set clock rate on probe (%d); "
-		       "continue anyway\n", host->dev_index, err);
-	}
-
-	host->name = "EXYNOS DWMMC";
-	host->board_init = exynos_dwmci_board_init;
-	host->caps = MMC_MODE_DDR_52MHz;
-	host->clksel = exynos_dwmci_clksel;
-	host->get_mmc_clk = exynos_dwmci_get_clk;
-
-#ifndef CONFIG_DM_MMC
-	/* Add the mmc channel to be registered with mmc core */
-	if (add_dwmci(host, DWMMC_MAX_FREQ, DWMMC_MIN_FREQ)) {
-		printf("DWMMC%d registration failed\n", host->dev_index);
-		return -1;
-	}
-#endif
-
-	return 0;
-}
-
-static int do_dwmci_init(struct dwmci_host *host)
-{
-#ifdef CONFIG_CPU_V7A
-	int flag, err;
-
-	flag = host->buswidth == 8 ? PINMUX_FLAG_8BIT_MODE : PINMUX_FLAG_NONE;
-	err = exynos_pinmux_config(host->dev_id, flag);
-	if (err) {
-		printf("DWMMC%d not configure\n", host->dev_index);
-		return err;
-	}
-#endif
-
-	return exynos_dwmci_core_init(host);
-}
-
 #ifdef CONFIG_DM_MMC
 static int exynos_dwmmc_of_to_plat(struct udevice *dev)
 {
@@ -345,6 +296,7 @@ static int exynos_dwmmc_probe(struct udevice *dev)
 	struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev);
 	struct dwmci_exynos_priv_data *priv = dev_get_priv(dev);
 	struct dwmci_host *host = &priv->host;
+	unsigned long freq;
 	int err;
 
 #ifndef CONFIG_CPU_V7A
@@ -353,9 +305,41 @@ static int exynos_dwmmc_probe(struct udevice *dev)
 		return err;
 #endif
 
-	err = do_dwmci_init(host);
-	if (err)
+#ifdef CONFIG_CPU_V7A
+	int flag;
+
+	flag = host->buswidth == 8 ? PINMUX_FLAG_8BIT_MODE : PINMUX_FLAG_NONE;
+	err = exynos_pinmux_config(host->dev_id, flag);
+	if (err) {
+		printf("DWMMC%d not configure\n", host->dev_index);
 		return err;
+	}
+#endif
+
+	if (host->bus_hz)
+		freq = host->bus_hz;
+	else
+		freq = DWMMC_MAX_FREQ;
+
+	err = exynos_dwmmc_set_sclk(host, freq);
+	if (err) {
+		printf("DWMMC%d: failed to set clock rate on probe (%d); "
+		       "continue anyway\n", host->dev_index, err);
+	}
+
+	host->name = "EXYNOS DWMMC";
+	host->board_init = exynos_dwmci_board_init;
+	host->caps = MMC_MODE_DDR_52MHz;
+	host->clksel = exynos_dwmci_clksel;
+	host->get_mmc_clk = exynos_dwmci_get_clk;
+
+#ifndef CONFIG_DM_MMC
+	/* Add the mmc channel to be registered with mmc core */
+	if (add_dwmci(host, DWMMC_MAX_FREQ, DWMMC_MIN_FREQ)) {
+		printf("DWMMC%d registration failed\n", host->dev_index);
+		return -1;
+	}
+#endif
 
 	dwmci_setup_cfg(&plat->cfg, host, DWMMC_MAX_FREQ, DWMMC_MIN_FREQ);
 	host->mmc = &plat->mmc;
-- 
2.39.2



More information about the U-Boot mailing list