[PATCH v2 11/18] i2c: Drop reference to SYS_I2C_INIT_BOARD

[Simon Glass]

This is not now used by any boards, so drop it.

Signed-off-by: Simon Glass <sjg at chromium.org>
---

(no changes since v1)

 doc/I2C_Edge_Conditions | 10 ++++------
 drivers/i2c/soft_i2c.c  | 11 -----------
 2 files changed, 4 insertions(+), 17 deletions(-)

diff --git a/doc/I2C_Edge_Conditions b/doc/I2C_Edge_Conditions
index f4a99687011..9ccb21c5092 100644
--- a/doc/I2C_Edge_Conditions
+++ b/doc/I2C_Edge_Conditions
@@ -31,12 +31,10 @@ Notes
 !!!THIS IS AN UNDOCUMENTED I2C BUS BUG, NOT A AMCC 4xx BUG!!!
 
 This reset edge condition could possibly be present in every I2C
-controller and device available. For boards where a I2C bus reset
-function can be implemented a i2c_init_board() function should be
-provided and enabled by #define'ing CONFIG_SYS_I2C_INIT_BOARD in your
-board's config file. Note that this is NOT necessary when using the
-bit-banging I2C driver (common/soft_i2c.c) as this already includes
-the I2C bus reset sequence.
+controller and device available.
+
+Note that this problem does not happen when using the bit-banging I2C driver
+(common/soft_i2c.c) as this already includes the I2C bus reset sequence.
 
 
 Many thanks to Bill Hunter for finding this serious BUG.
diff --git a/drivers/i2c/soft_i2c.c b/drivers/i2c/soft_i2c.c
index 89ddf821063..79f7a320502 100644
--- a/drivers/i2c/soft_i2c.c
+++ b/drivers/i2c/soft_i2c.c
@@ -107,16 +107,13 @@ DECLARE_GLOBAL_DATA_PTR;
 /*-----------------------------------------------------------------------
  * Local functions
  */
-#if !defined(CONFIG_SYS_I2C_INIT_BOARD)
 static void  send_reset	(void);
-#endif
 static void  send_start	(void);
 static void  send_stop	(void);
 static void  send_ack	(int);
 static int   write_byte	(uchar byte);
 static uchar read_byte	(int);
 
-#if !defined(CONFIG_SYS_I2C_INIT_BOARD)
 /*-----------------------------------------------------------------------
  * Send a reset sequence consisting of 9 clocks with the data signal high
  * to clock any confused device back into an idle state.  Also send a
@@ -144,7 +141,6 @@ static void send_reset(void)
 	send_stop();
 	I2C_TRISTATE;
 }
-#endif
 
 /*-----------------------------------------------------------------------
  * START: High -> Low on SDA while SCL is High
@@ -277,12 +273,6 @@ static uchar read_byte(int ack)
  */
 static void soft_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr)
 {
-#if defined(CONFIG_SYS_I2C_INIT_BOARD)
-	/* call board specific i2c bus reset routine before accessing the   */
-	/* environment, which might be in a chip on that bus. For details   */
-	/* about this problem see doc/I2C_Edge_Conditions.                  */
-	i2c_init_board();
-#else
 	/*
 	 * WARNING: Do NOT save speed in a static variable: if the
 	 * I2C routines are called before RAM is initialized (to read
@@ -290,7 +280,6 @@ static void soft_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr)
 	 * system will crash.
 	 */
 	send_reset ();
-#endif
 }
 
 /*-----------------------------------------------------------------------
-- 
2.34.1