[PATCH 3/3] tqma6_mba6: Remove UART board code

[Fabio Estevam]

From: Fabio Estevam <festevam at denx.de>

With DM_SERIAL in place, there is no need to setup the UART pins
in the board code.

The UART pins are setup via devicetree, thanks to DM.

Remove the unneeded code.

Signed-off-by: Fabio Estevam <festevam at denx.de>
---
 arch/arm/dts/imx6qdl-mba6-u-boot.dtsi | 16 ++++++++++++++++
 board/tq/tqma6/tqma6_mba6.c           | 16 ----------------
 2 files changed, 16 insertions(+), 16 deletions(-)

diff --git a/arch/arm/dts/imx6qdl-mba6-u-boot.dtsi b/arch/arm/dts/imx6qdl-mba6-u-boot.dtsi
index 78457ef68f4..c8c0fc1fba7 100644
--- a/arch/arm/dts/imx6qdl-mba6-u-boot.dtsi
+++ b/arch/arm/dts/imx6qdl-mba6-u-boot.dtsi
@@ -10,6 +10,22 @@
 	};
 };
 
+&aips2 {
+	bootph-all;
+};
+
+&pinctrl_uart2 {
+	bootph-all;
+};
+
+&soc {
+	bootph-all;
+};
+
+&uart2 {
+	bootph-all;
+};
+
 &wdog1 {
 	bootph-pre-ram;
 };
diff --git a/board/tq/tqma6/tqma6_mba6.c b/board/tq/tqma6/tqma6_mba6.c
index 7267d812e7d..b8f76591006 100644
--- a/board/tq/tqma6/tqma6_mba6.c
+++ b/board/tq/tqma6/tqma6_mba6.c
@@ -31,9 +31,6 @@
 
 #include "tqma6_bb.h"
 
-#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
-	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
-
 #if defined(CONFIG_TQMA6Q)
 
 #define IOMUX_SW_PAD_CTRL_GRP_DDR_TYPE_RGMII	0x02e0790
@@ -70,17 +67,6 @@ static void mba6_setup_iomuxc_enet(void)
 		     (void *)IOMUX_SW_PAD_CTRL_GRP_DDR_TYPE_RGMII);
 }
 
-static iomux_v3_cfg_t const mba6_uart2_pads[] = {
-	NEW_PAD_CTRL(MX6_PAD_SD4_DAT4__UART2_RX_DATA, UART_PAD_CTRL),
-	NEW_PAD_CTRL(MX6_PAD_SD4_DAT7__UART2_TX_DATA, UART_PAD_CTRL),
-};
-
-static void mba6_setup_iomuxc_uart(void)
-{
-	imx_iomux_v3_setup_multiple_pads(mba6_uart2_pads,
-					 ARRAY_SIZE(mba6_uart2_pads));
-}
-
 int board_mmc_get_env_dev(int devno)
 {
 	/*
@@ -140,8 +126,6 @@ int board_phy_config(struct phy_device *phydev)
 
 int tqma6_bb_board_early_init_f(void)
 {
-	mba6_setup_iomuxc_uart();
-
 	return 0;
 }
 
-- 
2.34.1