[PATCH 3/5] arm: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS

[Tim Harvey]

The GW71xx does not have a gpio controlled vbus regulator but it does
require some pinctrl. Remove the regulator and move the valid pinctrl
into the usbotg1 node.

Signed-off-by: Tim Harvey <tharvey at gateworks.com>
---
 arch/arm/dts/imx8mm-venice-gw71xx.dtsi | 29 ++++++++------------------
 1 file changed, 9 insertions(+), 20 deletions(-)

diff --git a/arch/arm/dts/imx8mm-venice-gw71xx.dtsi b/arch/arm/dts/imx8mm-venice-gw71xx.dtsi
index c557dbf4dcd6..2e90466db89a 100644
--- a/arch/arm/dts/imx8mm-venice-gw71xx.dtsi
+++ b/arch/arm/dts/imx8mm-venice-gw71xx.dtsi
@@ -47,17 +47,6 @@
 		gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
 		status = "okay";
 	};
-
-	reg_usb_otg1_vbus: regulator-usb-otg1 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_reg_usb1_en>;
-		compatible = "regulator-fixed";
-		regulator-name = "usb_otg1_vbus";
-		gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
 };
 
 /* off-board header */
@@ -146,9 +135,10 @@
 };
 
 &usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
 	dr_mode = "otg";
 	over-current-active-low;
-	vbus-supply = <&reg_usb_otg1_vbus>;
 	status = "okay";
 };
 
@@ -206,14 +196,6 @@
 		>;
 	};
 
-	pinctrl_reg_usb1_en: regusb1grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10	0x41
-			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x141
-			MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC	0x41
-		>;
-	};
-
 	pinctrl_spi2: spi2grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
@@ -236,4 +218,11 @@
 			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX	0x140
 		>;
 	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x141
+			MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC	0x41
+		>;
+	};
 };
-- 
2.25.1