[PATCH v4 34/39] dts: msm8996: import PMIC dtsi files

Caleb Connolly caleb.connolly at linaro.org
Thu Feb 15 21:52:52 CET 2024


Import PM8994 and PMI8994 DTSI files in preparation for switching
MSM8996 boards to upstream DTS.

Taken from kernel tag v6.7

Reviewed-by: Neil Armstrong <neil.armstrong at linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly at linaro.org>
---
 arch/arm/dts/pm8994.dtsi  | 152 ++++++++++++++++++++++++++++++++++++++++++++++
 arch/arm/dts/pmi8994.dtsi |  65 ++++++++++++++++++++
 2 files changed, 217 insertions(+)

diff --git a/arch/arm/dts/pm8994.dtsi b/arch/arm/dts/pm8994.dtsi
new file mode 100644
index 000000000000..d44a95caf04a
--- /dev/null
+++ b/arch/arm/dts/pm8994.dtsi
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pm8994-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&pm8994_temp>;
+
+			trips {
+				pm8994_alert0: pm8994-alert0 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				pm8994_crit: pm8994-crit {
+					temperature = <125000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+
+	pmic at 0 {
+		compatible = "qcom,pm8994", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtc at 6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>, <0x6100>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		pm8994_pon: pon at 800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x800>;
+			mode-bootloader = <0x2>;
+			mode-recovery = <0x1>;
+
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+			};
+
+			pm8994_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				status = "disabled";
+			};
+		};
+
+		pm8994_temp: temp-alarm at 2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
+			io-channels = <&pm8994_vadc VADC_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8994_vadc: adc at 3100 {
+			compatible = "qcom,spmi-vadc";
+			reg = <0x3100>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+
+			channel at 7 {
+				reg = <VADC_VSYS>;
+				qcom,pre-scaling = <1 3>;
+				label = "vph_pwr";
+			};
+			channel at 8 {
+				reg = <VADC_DIE_TEMP>;
+				label = "die_temp";
+			};
+			channel at 9 {
+				reg = <VADC_REF_625MV>;
+				label = "ref_625mv";
+			};
+			channel at a {
+				reg = <VADC_REF_1250MV>;
+				label = "ref_1250mv";
+			};
+			channel at e {
+				reg = <VADC_GND_REF>;
+			};
+			channel at f {
+				reg = <VADC_VDD_VADC>;
+			};
+		};
+
+		pm8994_gpios: gpio at c000 {
+			compatible = "qcom,pm8994-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pm8994_gpios 0 0 22>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pm8994_mpps: mpps at a000 {
+			compatible = "qcom,pm8994-mpp", "qcom,spmi-mpp";
+			reg = <0xa000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8994_mpps 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmic at 1 {
+		compatible = "qcom,pm8994", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8994_lpg: pwm {
+			compatible = "qcom,pm8994-lpg";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+
+		pm8994_spmi_regulators: regulators {
+			compatible = "qcom,pm8994-regulators";
+		};
+	};
+};
diff --git a/arch/arm/dts/pmi8994.dtsi b/arch/arm/dts/pmi8994.dtsi
new file mode 100644
index 000000000000..36d6a1fb553a
--- /dev/null
+++ b/arch/arm/dts/pmi8994.dtsi
@@ -0,0 +1,65 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+
+	pmic at 2 {
+		compatible = "qcom,pmi8994", "qcom,spmi-pmic";
+		reg = <0x2 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmi8994_gpios: gpio at c000 {
+			compatible = "qcom,pmi8994-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pmi8994_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pmi8994_mpps: mpps at a000 {
+			compatible = "qcom,pmi8994-mpp", "qcom,spmi-mpp";
+			reg = <0xa000>;
+			gpio-controller;
+			gpio-ranges = <&pmi8994_mpps 0 0 4>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmic at 3 {
+		compatible = "qcom,pmi8994", "qcom,spmi-pmic";
+		reg = <0x3 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmi8994_lpg: pwm {
+			compatible = "qcom,pmi8994-lpg";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+
+		pmi8994_spmi_regulators: regulators {
+			compatible = "qcom,pmi8994-regulators";
+		};
+
+		pmi8994_wled: wled at d800 {
+			compatible = "qcom,pmi8994-wled";
+			reg = <0xd800>, <0xd900>;
+			interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>,
+				     <0x3 0xd8 0x2 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ovp", "short";
+			qcom,cabc;
+			qcom,external-pfet;
+			status = "disabled";
+		};
+	};
+};

-- 
2.43.1



More information about the U-Boot mailing list