[PATCH v4 38/39] dts: qcs404-evb: replace with upstream DT
Caleb Connolly
caleb.connolly at linaro.org
Thu Feb 15 21:52:56 CET 2024
Drop the U-Boot specific DTS in favour of upstream. We'll only include
the -4000 variant as that is what U-Boot already supported.
Taken from kernel tag v6.7
Reviewed-by: Neil Armstrong <neil.armstrong at linaro.org>
Signed-off-by: Caleb Connolly <caleb.connolly at linaro.org>
---
arch/arm/dts/Makefile | 2 +-
arch/arm/dts/pms405.dtsi | 149 +++
arch/arm/dts/qcs404-evb-4000-u-boot.dtsi | 48 +
arch/arm/dts/qcs404-evb-4000.dts | 96 ++
arch/arm/dts/qcs404-evb-uboot.dtsi | 30 -
arch/arm/dts/qcs404-evb.dts | 390 -------
arch/arm/dts/qcs404-evb.dtsi | 389 +++++++
arch/arm/dts/qcs404.dtsi | 1829 ++++++++++++++++++++++++++++++
8 files changed, 2512 insertions(+), 421 deletions(-)
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 54aaf022c2eb..c4f0873dbb1f 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -635,7 +635,7 @@ dtb-$(CONFIG_ARCH_SNAPDRAGON) += apq8016-sbc.dtb \
apq8096-db820c.dtb \
sdm845-db845c.dtb \
sdm845-samsung-starqltechn.dtb \
- qcs404-evb.dtb
+ qcs404-evb-4000.dtb
dtb-$(CONFIG_TARGET_STEMMY) += ste-ux500-samsung-stemmy.dtb
diff --git a/arch/arm/dts/pms405.dtsi b/arch/arm/dts/pms405.dtsi
new file mode 100644
index 000000000000..461ad97032f7
--- /dev/null
+++ b/arch/arm/dts/pms405.dtsi
@@ -0,0 +1,149 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, Linaro Limited
+ */
+
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ thermal-zones {
+ pms405-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&pms405_temp>;
+
+ trips {
+ pms405_alert0: pms405-alert0 {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ pms405_crit: pms405-crit {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+ };
+};
+
+&spmi_bus {
+ pms405_0: pms405 at 0 {
+ compatible = "qcom,pms405", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pms405_gpios: gpio at c000 {
+ compatible = "qcom,pms405-gpio", "qcom,spmi-gpio";
+ reg = <0xc000>;
+ gpio-controller;
+ gpio-ranges = <&pms405_gpios 0 0 12>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ pon at 800 {
+ compatible = "qcom,pms405-pon";
+ reg = <0x0800>;
+ mode-bootloader = <0x2>;
+ mode-recovery = <0x1>;
+
+ pwrkey {
+ compatible = "qcom,pm8941-pwrkey";
+ interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_POWER>;
+ };
+ };
+
+ pms405_temp: temp-alarm at 2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+ io-channels = <&pms405_adc ADC5_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
+ pms405_adc: adc at 3100 {
+ compatible = "qcom,pms405-adc", "qcom,spmi-adc-rev2";
+ reg = <0x3100>;
+ interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+
+ channel at 0 {
+ reg = <ADC5_REF_GND>;
+ qcom,pre-scaling = <1 1>;
+ label = "ref_gnd";
+ };
+
+ channel at 1 {
+ reg = <ADC5_1P25VREF>;
+ qcom,pre-scaling = <1 1>;
+ label = "vref_1p25";
+ };
+
+ channel at 131 {
+ reg = <ADC5_VPH_PWR>;
+ qcom,pre-scaling = <1 3>;
+ label = "vph_pwr";
+ };
+
+ channel at 6 {
+ reg = <ADC5_DIE_TEMP>;
+ qcom,pre-scaling = <1 1>;
+ label = "die_temp";
+ };
+
+ channel at 77 {
+ reg = <ADC5_AMUX_THM1_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ label = "pa_therm1";
+ };
+
+ channel at 79 {
+ reg = <ADC5_AMUX_THM3_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ label = "pa_therm3";
+ };
+
+ channel at 76 {
+ reg = <ADC5_XO_THERM_100K_PU>;
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ label = "xo_therm";
+ };
+ };
+
+ rtc at 6000 {
+ compatible = "qcom,pm8941-rtc";
+ reg = <0x6000>, <0x6100>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+ };
+ };
+
+ pms405_1: pms405 at 1 {
+ compatible = "qcom,pms405", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+
+ pms405_spmi_regulators: regulators {
+ compatible = "qcom,pms405-regulators";
+ };
+ };
+};
diff --git a/arch/arm/dts/qcs404-evb-4000-u-boot.dtsi b/arch/arm/dts/qcs404-evb-4000-u-boot.dtsi
new file mode 100644
index 000000000000..d3033ea42ec1
--- /dev/null
+++ b/arch/arm/dts/qcs404-evb-4000-u-boot.dtsi
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <dt-bindings/gpio/gpio.h>
+
+/delete-node/ &usb3_vbus_reg;
+/delete-node/ &usb_vbus_boost_pin;
+
+/ {
+ /* U-Boot uses different bindings for GPIO regulators, this
+ * one is required for USB
+ */
+ usb3_vbus_reg: usb3_vbus_reg {
+ compatible = "regulator-gpio";
+ regulator-name = "usb3_vbus_reg";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-gpios = <&pms405_gpios 3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ states = <0 0>, <5000000 1>;
+ };
+};
+
+&blsp1_uart2 {
+ /* This defines the bit clock divider which defines the baud rate.
+ * 0xFF is a divider of 16 for both the RX and TX lines. The QCS404
+ * clock driver in U-Boot hardcodes a 1843200Hz frequency for the
+ * UART core clock, and 1843200 / 16 = 115200.
+ */
+ bit-rate = <0xFF>;
+};
+
+&gcc {
+ /* The clock framework in U-Boot "sort of" has the idea of linking an
+ * individual clock to a device via uclass_priv. However the qcom clock
+ * driver instead associates many clocks with a single device. This is
+ * usually fine but it seems that assigned-clocks wreak havoc on this
+ * and we wind up having a reference to the XO clock which is associated
+ * with the qcom_clk device...
+ * For now we'll just remove these properties, no other board has these.
+ */
+ /delete-property/ assigned-clock-rates;
+ /delete-property/ assigned-clocks;
+};
+
+&usb3_dwc3 {
+ /* Make sure the VBUS supply is switched on */
+ vbus-supply = <&usb3_vbus_reg>;
+};
diff --git a/arch/arm/dts/qcs404-evb-4000.dts b/arch/arm/dts/qcs404-evb-4000.dts
new file mode 100644
index 000000000000..358827c2fbd3
--- /dev/null
+++ b/arch/arm/dts/qcs404-evb-4000.dts
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "qcs404-evb.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. QCS404 EVB 4000";
+ compatible = "qcom,qcs404-evb-4000", "qcom,qcs404-evb",
+ "qcom,qcs404";
+};
+
+ðernet {
+ status = "okay";
+
+ snps,reset-gpio = <&tlmm 60 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 10000>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <ðernet_defaults>;
+
+ phy-handle = <&phy1>;
+ phy-mode = "rgmii";
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy1: phy at 4 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ device_type = "ethernet-phy";
+ reg = <0x4>;
+ };
+ };
+};
+
+&tlmm {
+ ethernet_defaults: ethernet-defaults-state {
+ int-pins {
+ pins = "gpio61";
+ function = "rgmii_int";
+ bias-disable;
+ drive-strength = <2>;
+ };
+ mdc-pins {
+ pins = "gpio76";
+ function = "rgmii_mdc";
+ bias-pull-up;
+ };
+ mdio-pins {
+ pins = "gpio75";
+ function = "rgmii_mdio";
+ bias-pull-up;
+ };
+ tx-pins {
+ pins = "gpio67", "gpio66", "gpio65", "gpio64";
+ function = "rgmii_tx";
+ bias-pull-up;
+ drive-strength = <16>;
+ };
+ rx-pins {
+ pins = "gpio73", "gpio72", "gpio71", "gpio70";
+ function = "rgmii_rx";
+ bias-disable;
+ drive-strength = <2>;
+ };
+ tx-ctl-pins {
+ pins = "gpio68";
+ function = "rgmii_ctl";
+ bias-pull-up;
+ drive-strength = <16>;
+ };
+ rx-ctl-pins {
+ pins = "gpio74";
+ function = "rgmii_ctl";
+ bias-disable;
+ drive-strength = <2>;
+ };
+ tx-ck-pins {
+ pins = "gpio63";
+ function = "rgmii_ck";
+ bias-pull-up;
+ drive-strength = <16>;
+ };
+ rx-ck-pins {
+ pins = "gpio69";
+ function = "rgmii_ck";
+ bias-disable;
+ drive-strength = <2>;
+ };
+ };
+};
diff --git a/arch/arm/dts/qcs404-evb-uboot.dtsi b/arch/arm/dts/qcs404-evb-uboot.dtsi
deleted file mode 100644
index b4c5f3fa4301..000000000000
--- a/arch/arm/dts/qcs404-evb-uboot.dtsi
+++ /dev/null
@@ -1,30 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * U-Boot addition to handle QCS404 EVB pre-relocation devices
- *
- * (C) Copyright 2022 Sumit Garg <sumit.garg at linaro.org>
- */
-
-/ {
- soc {
- bootph-all;
-
- pinctrl_north at 1300000 {
- bootph-all;
- };
-
- clock-controller at 1800000 {
- bootph-all;
- };
-
- serial at 78b1000 {
- bootph-all;
- };
- };
-};
-
-&pms405_gpios {
- usb_vbus_boost_pin {
- gpios = <&pms405_gpios 2 0>;
- };
-};
diff --git a/arch/arm/dts/qcs404-evb.dts b/arch/arm/dts/qcs404-evb.dts
deleted file mode 100644
index 07bf7dd0b32f..000000000000
--- a/arch/arm/dts/qcs404-evb.dts
+++ /dev/null
@@ -1,390 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Qualcomm QCS404 based evaluation board device tree source
- *
- * (C) Copyright 2022 Sumit Garg <sumit.garg at linaro.org>
- */
-
-/dts-v1/;
-
-#include "skeleton64.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clock/qcom,gcc-qcs404.h>
-
-/ {
- model = "Qualcomm Technologies, Inc. QCS404 EVB";
- compatible = "qcom,qcs404-evb", "qcom,qcs404";
- #address-cells = <0x2>;
- #size-cells = <0x2>;
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- aliases {
- serial0 = &debug_uart;
- i2c0 = &blsp1_i2c0;
- i2c1 = &blsp1_i2c1;
- i2c2 = &blsp1_i2c2;
- i2c3 = &blsp1_i2c3;
- i2c4 = &blsp1_i2c4;
- };
-
- memory {
- device_type = "memory";
- reg = <0 0x80000000 0 0x40000000>;
- };
-
- soc {
- #address-cells = <0x1>;
- #size-cells = <0x1>;
- ranges = <0x0 0x0 0x0 0xffffffff>;
- compatible = "simple-bus";
-
- soc_gpios: pinctrl_north at 1300000 {
- compatible = "qcom,qcs404-pinctrl";
- reg = <0x1300000 0x200000>;
- gpio-controller;
- gpio-count = <120>;
- gpio-bank-name="soc";
- #gpio-cells = <2>;
-
- blsp1_uart2: uart {
- pins = "GPIO_17", "GPIO_18";
- function = "blsp_uart2";
- };
-
- blsp1_i2c0_default: blsp1-i2c0-default {
- pins = "GPIO_32", "GPIO_33";
- function = "blsp_i2c0";
- };
-
- blsp1_i2c1_default: blsp1-i2c1-default {
- pins = "GPIO_24", "GPIO_25";
- function = "blsp_i2c1";
- };
-
- blsp1_i2c2_default: blsp1-i2c2-default {
- sda {
- pins = "GPIO_19";
- function = "blsp_i2c_sda_a2";
- };
-
- scl {
- pins = "GPIO_20";
- function = "blsp_i2c_scl_a2";
- };
- };
-
- blsp1_i2c3_default: blsp1-i2c3-default {
- pins = "GPIO_84", "GPIO_85";
- function = "blsp_i2c3";
- };
-
- blsp1_i2c4_default: blsp1-i2c4-default {
- pins = "GPIO_117", "GPIO_118";
- function = "blsp_i2c4";
- };
-
- ethernet_defaults: ethernet-defaults {
- int {
- pins = "GPIO_61";
- function = "rgmii_int";
- bias-disable;
- drive-strength = <2>;
- };
- mdc {
- pins = "GPIO_76";
- function = "rgmii_mdc";
- bias-pull-up;
- };
- mdio {
- pins = "GPIO_75";
- function = "rgmii_mdio";
- bias-pull-up;
- };
- tx {
- pins = "GPIO_67", "GPIO_66", "GPIO_65", "GPIO_64";
- function = "rgmii_tx";
- bias-pull-up;
- drive-strength = <16>;
- };
- rx {
- pins = "GPIO_73", "GPIO_72", "GPIO_71", "GPIO_70";
- function = "rgmii_rx";
- bias-disable;
- drive-strength = <2>;
- };
- tx-ctl {
- pins = "GPIO_68";
- function = "rgmii_ctl";
- bias-pull-up;
- drive-strength = <16>;
- };
- rx-ctl {
- pins = "GPIO_74";
- function = "rgmii_ctl";
- bias-disable;
- drive-strength = <2>;
- };
- tx-ck {
- pins = "GPIO_63";
- function = "rgmii_ck";
- bias-pull-up;
- drive-strength = <16>;
- };
- rx-ck {
- pins = "GPIO_69";
- function = "rgmii_ck";
- bias-disable;
- drive-strength = <2>;
- };
- };
- };
-
- blsp1_i2c0: i2c at 78b5000 {
- compatible = "qcom,i2c-qup-v2.2.1";
- reg = <0x078b5000 0x600>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP0_I2C_APPS_CLK>;
- clock-names = "iface", "core";
- pinctrl-names = "default";
- pinctrl-0 = <&blsp1_i2c0_default>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- blsp1_i2c1: i2c at 78b6000 {
- compatible = "qcom,i2c-qup-v2.2.1";
- reg = <0x078b6000 0x600>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>;
- clock-names = "iface", "core";
- pinctrl-names = "default";
- pinctrl-0 = <&blsp1_i2c1_default>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- blsp1_i2c2: i2c at 78b7000 {
- compatible = "qcom,i2c-qup-v2.2.1";
- reg = <0x078b7000 0x600>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
- clock-names = "iface", "core";
- pinctrl-names = "default";
- pinctrl-0 = <&blsp1_i2c2_default>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- blsp1_i2c3: i2c at 78b8000 {
- compatible = "qcom,i2c-qup-v2.2.1";
- reg = <0x078b8000 0x600>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
- clock-names = "iface", "core";
- pinctrl-names = "default";
- pinctrl-0 = <&blsp1_i2c3_default>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- blsp1_i2c4: i2c at 78b9000 {
- compatible = "qcom,i2c-qup-v2.2.1";
- reg = <0x078b9000 0x600>;
- clocks = <&gcc GCC_BLSP1_AHB_CLK>,
- <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>;
- clock-names = "iface", "core";
- pinctrl-names = "default";
- pinctrl-0 = <&blsp1_i2c4_default>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- gcc: clock-controller at 1800000 {
- compatible = "qcom,gcc-qcs404";
- reg = <0x1800000 0x80000>;
- #address-cells = <0x1>;
- #size-cells = <0x0>;
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- debug_uart: serial at 78b1000 {
- compatible = "qcom,msm-uartdm-v1.4";
- reg = <0x78b1000 0x200>;
- clock = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
- <&gcc GCC_BLSP1_AHB_CLK>;
- bit-rate = <0xFF>;
- pinctrl-names = "uart";
- pinctrl-0 = <&blsp1_uart2>;
- };
-
- sdhci at 7804000 {
- compatible = "qcom,sdhci-msm-v5";
- reg = <0x7804000 0x1000 0x7805000 0x1000>;
- clock = <&gcc GCC_SDCC1_APPS_CLK>,
- <&gcc GCC_SDCC1_AHB_CLK>;
- bus-width = <0x8>;
- index = <0x0>;
- non-removable;
- mmc-ddr-1_8v;
- mmc-hs400-1_8v;
- };
-
- usb3_phy: phy at 78000 {
- compatible = "qcom,usb-ss-28nm-phy";
- #phy-cells = <0>;
- reg = <0x78000 0x400>;
- clocks = <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
- <&gcc GCC_USB3_PHY_PIPE_CLK>;
- clock-names = "ahb", "pipe";
- resets = <&gcc GCC_USB3_PHY_BCR>,
- <&gcc GCC_USB3PHY_PHY_BCR>;
- reset-names = "com", "phy";
- };
-
- usb2_phy_prim: phy at 7a000 {
- compatible = "qcom,usb-hs-28nm-femtophy";
- #phy-cells = <0>;
- reg = <0x7a000 0x200>;
- clocks = <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
- <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
- clock-names = "ahb", "sleep";
- resets = <&gcc GCC_USB_HS_PHY_CFG_AHB_BCR>,
- <&gcc GCC_USB2A_PHY_BCR>;
- reset-names = "phy", "por";
- };
-
- usb2_phy_sec: phy at 7c000 {
- compatible = "qcom,usb-hs-28nm-femtophy";
- #phy-cells = <0>;
- reg = <0x7c000 0x200>;
- clocks = <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
- <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
- clock-names = "ahb", "sleep";
- resets = <&gcc GCC_QUSB2_PHY_BCR>,
- <&gcc GCC_USB2_HS_PHY_ONLY_BCR>;
- reset-names = "phy", "por";
- };
-
- usb3: usb at 7678800 {
- compatible = "qcom,dwc3";
- reg = <0x7678800 0x400>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- clocks = <&gcc GCC_USB30_MASTER_CLK>,
- <&gcc GCC_SYS_NOC_USB3_CLK>,
- <&gcc GCC_USB30_SLEEP_CLK>,
- <&gcc GCC_USB30_MOCK_UTMI_CLK>;
- clock-names = "core", "iface", "sleep", "mock_utmi";
-
- dwc3 at 7580000 {
- compatible = "snps,dwc3";
- reg = <0x7580000 0xcd00>;
- phys = <&usb2_phy_prim>, <&usb3_phy>;
- phy-names = "usb2-phy", "usb3-phy";
- dr_mode = "host";
- snps,has-lpm-erratum;
- snps,hird-threshold = /bits/ 8 <0x10>;
- snps,usb3_lpm_capable;
- maximum-speed = "super-speed";
- };
- };
-
- usb2: usb at 79b8800 {
- compatible = "qcom,dwc3";
- reg = <0x79b8800 0x400>;
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>,
- <&gcc GCC_PCNOC_USB2_CLK>,
- <&gcc GCC_USB_HS_INACTIVITY_TIMERS_CLK>,
- <&gcc GCC_USB20_MOCK_UTMI_CLK>;
- clock-names = "core", "iface", "sleep", "mock_utmi";
-
- dwc3 at 78c0000 {
- compatible = "snps,dwc3";
- reg = <0x78c0000 0xcc00>;
- phys = <&usb2_phy_sec>;
- phy-names = "usb2-phy";
- dr_mode = "peripheral";
- snps,has-lpm-erratum;
- snps,hird-threshold = /bits/ 8 <0x10>;
- snps,usb3_lpm_capable;
- maximum-speed = "high-speed";
- };
- };
-
- ethernet: ethernet at 7a80000 {
- compatible = "qcom,qcs404-ethqos";
- reg = <0x07a80000 0x10000>,
- <0x07a96000 0x100>;
- reg-names = "stmmaceth", "rgmii";
- clock-names = "stmmaceth", "pclk", "ptp_ref", "rgmii";
- clocks = <&gcc GCC_ETH_AXI_CLK>,
- <&gcc GCC_ETH_SLAVE_AHB_CLK>,
- <&gcc GCC_ETH_PTP_CLK>,
- <&gcc GCC_ETH_RGMII_CLK>;
-
- resets = <&gcc GCC_EMAC_BCR>;
- reset-names = "emac";
-
- snps,tso;
- rx-fifo-depth = <4096>;
- tx-fifo-depth = <4096>;
-
- snps,reset-gpio = <&soc_gpios 60 GPIO_ACTIVE_LOW>;
- snps,reset-active-low;
- snps,reset-delays-us = <0 10000 10000>;
-
- pinctrl-names = "default";
- pinctrl-0 = <ðernet_defaults>;
-
- phy-handle = <&phy1>;
- phy-mode = "rgmii";
- max-speed = <1000>;
-
- mdio {
- #address-cells = <0x1>;
- #size-cells = <0x0>;
- compatible = "snps,dwmac-mdio";
- phy1: phy at 3 {
- compatible = "ethernet-phy-ieee802.3-c22";
- device_type = "ethernet-phy";
- reg = <0x3>;
- };
- };
- };
-
- spmi at 200f000 {
- compatible = "qcom,spmi-pmic-arb";
- reg = <0x200f000 0x001000>,
- <0x2400000 0x800000>,
- <0x2c00000 0x800000>;
- reg-names = "core", "chnls", "obsrvr";
- #address-cells = <0x1>;
- #size-cells = <0x1>;
-
- pms405_0: pms405 at 0 {
- compatible = "qcom,spmi-pmic";
- reg = <0x0 0x1>;
- #address-cells = <0x1>;
- #size-cells = <0x1>;
-
- pms405_gpios: pms405_gpios at c000 {
- compatible = "qcom,pms405-gpio";
- reg = <0xc000 0x400>;
- gpio-controller;
- gpio-ranges = <&pms405_gpios 0 0 12>;
- #gpio-cells = <2>;
- };
- };
- };
- };
-};
-
-#include "qcs404-evb-uboot.dtsi"
diff --git a/arch/arm/dts/qcs404-evb.dtsi b/arch/arm/dts/qcs404-evb.dtsi
new file mode 100644
index 000000000000..10655401528e
--- /dev/null
+++ b/arch/arm/dts/qcs404-evb.dtsi
@@ -0,0 +1,389 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, Linaro Limited
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include "qcs404.dtsi"
+#include "pms405.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+ aliases {
+ serial0 = &blsp1_uart2;
+ serial1 = &blsp1_uart3;
+ };
+
+ chosen {
+ stdout-path = "serial0";
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_ch0_3p3:
+ vdd_esmps3_3p3: vdd-esmps3-3p3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "eSMPS3_3P3";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ usb3_vbus_reg: regulator-usb3-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "VBUS_BOOST_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&pms405_gpios 3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_vbus_boost_pin>;
+ vin-supply = <&vph_pwr>;
+ enable-active-high;
+
+ /* TODO: Drop this when introducing role switching */
+ regulator-always-on;
+ };
+};
+
+&blsp1_uart3 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3990-bt";
+ vddio-supply = <&vreg_l6_1p8>;
+ vddxo-supply = <&vreg_l5_1p8>;
+ vddrf-supply = <&vreg_l1_1p3>;
+ vddch0-supply = <&vdd_ch0_3p3>;
+
+ local-bd-address = [ 02 00 00 00 5a ad ];
+
+ max-speed = <3200000>;
+ };
+};
+
+&blsp1_dma {
+ qcom,controlled-remotely;
+};
+
+&blsp2_dma {
+ qcom,controlled-remotely;
+};
+
+&gcc {
+ protected-clocks = <GCC_BIMC_CDSP_CLK>,
+ <GCC_CDSP_CFG_AHB_CLK>,
+ <GCC_CDSP_BIMC_CLK_SRC>,
+ <GCC_CDSP_TBU_CLK>,
+ <141>, /* GCC_WCSS_Q6_AHB_CLK */
+ <142>; /* GCC_WCSS_Q6_AXIM_CLK */
+};
+
+&pms405_spmi_regulators {
+ vdd_s3-supply = <&vph_pwr>;
+
+ pms405_s3: s3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vdd_apc";
+ regulator-initial-mode = <1>;
+ regulator-min-microvolt = <1048000>;
+ regulator-max-microvolt = <1384000>;
+ };
+};
+
+&pcie {
+ status = "okay";
+
+ perst-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&perst_state>;
+};
+
+&pcie_phy {
+ status = "okay";
+
+ vdda-vp-supply = <&vreg_l3_1p05>;
+ vdda-vph-supply = <&vreg_l5_1p8>;
+};
+
+&remoteproc_adsp {
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ status = "okay";
+};
+
+&remoteproc_wcss {
+ status = "okay";
+};
+
+&rpm_requests {
+ regulators {
+ compatible = "qcom,rpm-pms405-regulators";
+
+ vdd_s1-supply = <&vph_pwr>;
+ vdd_s2-supply = <&vph_pwr>;
+ vdd_s3-supply = <&vph_pwr>;
+ vdd_s4-supply = <&vph_pwr>;
+ vdd_s5-supply = <&vph_pwr>;
+ vdd_l1_l2-supply = <&vreg_s5_1p35>;
+ vdd_l3_l8-supply = <&vreg_s5_1p35>;
+ vdd_l4-supply = <&vreg_s5_1p35>;
+ vdd_l5_l6-supply = <&vreg_s4_1p8>;
+ vdd_l7-supply = <&vph_pwr>;
+ vdd_l9-supply = <&vreg_s5_1p35>;
+ vdd_l10_l11_l12_l13-supply = <&vph_pwr>;
+
+ vreg_s4_1p8: s4 {
+ regulator-min-microvolt = <1728000>;
+ regulator-max-microvolt = <1920000>;
+ };
+
+ vreg_s5_1p35: s5 {
+ regulator-min-microvolt = <1352000>;
+ regulator-max-microvolt = <1352000>;
+ };
+
+ vreg_l1_1p3: l1 {
+ regulator-min-microvolt = <1240000>;
+ regulator-max-microvolt = <1352000>;
+ };
+
+ vreg_l2_1p275: l2 {
+ regulator-min-microvolt = <1048000>;
+ regulator-max-microvolt = <1280000>;
+ };
+
+ vreg_l3_1p05: l3 {
+ regulator-min-microvolt = <1048000>;
+ regulator-max-microvolt = <1160000>;
+ };
+
+ vreg_l4_1p2: l4 {
+ regulator-min-microvolt = <1144000>;
+ regulator-max-microvolt = <1256000>;
+ };
+
+ vreg_l5_1p8: l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vreg_l6_1p8: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vreg_l7_1p8: l7 {
+ regulator-min-microvolt = <1616000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ vreg_l8_1p2: l8 {
+ regulator-min-microvolt = <1136000>;
+ regulator-max-microvolt = <1352000>;
+ };
+
+ vreg_l10_3p3: l10 {
+ regulator-min-microvolt = <2936000>;
+ regulator-max-microvolt = <3088000>;
+ };
+
+ vreg_l11_sdc2: l11 {
+ regulator-min-microvolt = <2696000>;
+ regulator-max-microvolt = <3304000>;
+ };
+
+ vreg_l12_3p3: l12 {
+ regulator-min-microvolt = <3050000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vreg_l13_3p3: l13 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+};
+
+&sdcc1 {
+ status = "okay";
+
+ supports-cqe;
+ mmc-ddr-1_8v;
+ mmc-hs400-1_8v;
+ bus-width = <8>;
+ non-removable;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc1_on>;
+ pinctrl-1 = <&sdc1_off>;
+};
+
+&tlmm {
+ perst_state: perst-state {
+ pins = "gpio43";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
+ sdc1_on: sdc1-on-state {
+ clk-pins {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ cmd-pins {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ data-pins {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ rclk-pins {
+ pins = "sdc1_rclk";
+ bias-pull-down;
+ };
+ };
+
+ sdc1_off: sdc1-off-state {
+ clk-pins {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cmd-pins {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ data-pins {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ rclk-pins {
+ pins = "sdc1_rclk";
+ bias-pull-down;
+ };
+ };
+
+ usb3_id_pin: usb3-id-state {
+ pins = "gpio116";
+ function = "gpio";
+
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+};
+
+&pms405_gpios {
+ usb_vbus_boost_pin: usb-vbus-boost-state {
+ pinconf {
+ pins = "gpio3";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ output-low;
+ power-source = <1>;
+ };
+ };
+ usb3_vbus_pin: usb3-vbus-state {
+ pinconf {
+ pins = "gpio12";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ input-enable;
+ bias-pull-down;
+ power-source = <1>;
+ };
+ };
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&usb2_phy_sec {
+ vdd-supply = <&vreg_l4_1p2>;
+ vdda1p8-supply = <&vreg_l5_1p8>;
+ vdda3p3-supply = <&vreg_l12_3p3>;
+ status = "okay";
+};
+
+&usb3 {
+ status = "okay";
+
+};
+
+&usb3_dwc3 {
+ dr_mode = "host";
+};
+
+&usb2_phy_prim {
+ vdd-supply = <&vreg_l4_1p2>;
+ vdda1p8-supply = <&vreg_l5_1p8>;
+ vdda3p3-supply = <&vreg_l12_3p3>;
+ status = "okay";
+};
+
+&usb3_phy {
+ vdd-supply = <&vreg_l3_1p05>;
+ vdda1p8-supply = <&vreg_l5_1p8>;
+ status = "okay";
+};
+
+&wifi {
+ status = "okay";
+ vdd-0.8-cx-mx-supply = <&vreg_l2_1p275>;
+ vdd-1.8-xo-supply = <&vreg_l5_1p8>;
+ vdd-1.3-rfa-supply = <&vreg_l1_1p3>;
+};
+
+/* PINCTRL - additions to nodes defined in qcs404.dtsi */
+
+&blsp1_uart2_default {
+ rx-pins {
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ tx-pins {
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&blsp1_uart3_default {
+ cts-pins {
+ bias-disable;
+ };
+
+ rts-tx-pins {
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx-pins {
+ bias-pull-up;
+ };
+};
diff --git a/arch/arm/dts/qcs404.dtsi b/arch/arm/dts/qcs404.dtsi
new file mode 100644
index 000000000000..2721f32dfb71
--- /dev/null
+++ b/arch/arm/dts/qcs404.dtsi
@@ -0,0 +1,1829 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, Linaro Limited
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-qcs404.h>
+#include <dt-bindings/clock/qcom,turingcc-qcs404.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+ interrupt-parent = <&intc>;
+
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ chosen { };
+
+ clocks {
+ xo_board: xo-board {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <19200000>;
+ };
+
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ CPU0: cpu at 100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x100>;
+ enable-method = "psci";
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ next-level-cache = <&L2_0>;
+ #cooling-cells = <2>;
+ clocks = <&apcs_glb>;
+ operating-points-v2 = <&cpu_opp_table>;
+ power-domains = <&cpr>;
+ power-domain-names = "cpr";
+ };
+
+ CPU1: cpu at 101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x101>;
+ enable-method = "psci";
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ next-level-cache = <&L2_0>;
+ #cooling-cells = <2>;
+ clocks = <&apcs_glb>;
+ operating-points-v2 = <&cpu_opp_table>;
+ power-domains = <&cpr>;
+ power-domain-names = "cpr";
+ };
+
+ CPU2: cpu at 102 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x102>;
+ enable-method = "psci";
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ next-level-cache = <&L2_0>;
+ #cooling-cells = <2>;
+ clocks = <&apcs_glb>;
+ operating-points-v2 = <&cpu_opp_table>;
+ power-domains = <&cpr>;
+ power-domain-names = "cpr";
+ };
+
+ CPU3: cpu at 103 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53";
+ reg = <0x103>;
+ enable-method = "psci";
+ cpu-idle-states = <&CPU_SLEEP_0>;
+ next-level-cache = <&L2_0>;
+ #cooling-cells = <2>;
+ clocks = <&apcs_glb>;
+ operating-points-v2 = <&cpu_opp_table>;
+ power-domains = <&cpr>;
+ power-domain-names = "cpr";
+ };
+
+ L2_0: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ cache-unified;
+ };
+
+ idle-states {
+ entry-method = "psci";
+
+ CPU_SLEEP_0: cpu-sleep-0 {
+ compatible = "arm,idle-state";
+ idle-state-name = "standalone-power-collapse";
+ arm,psci-suspend-param = <0x40000003>;
+ entry-latency-us = <125>;
+ exit-latency-us = <180>;
+ min-residency-us = <595>;
+ local-timer-stop;
+ };
+ };
+ };
+
+ cpu_opp_table: opp-table-cpu {
+ compatible = "operating-points-v2-kryo-cpu";
+ opp-shared;
+
+ opp-1094400000 {
+ opp-hz = /bits/ 64 <1094400000>;
+ required-opps = <&cpr_opp1>;
+ };
+ opp-1248000000 {
+ opp-hz = /bits/ 64 <1248000000>;
+ required-opps = <&cpr_opp2>;
+ };
+ opp-1401600000 {
+ opp-hz = /bits/ 64 <1401600000>;
+ required-opps = <&cpr_opp3>;
+ };
+ };
+
+ cpr_opp_table: opp-table-cpr {
+ compatible = "operating-points-v2-qcom-level";
+
+ cpr_opp1: opp1 {
+ opp-level = <1>;
+ qcom,opp-fuse-level = <1>;
+ };
+ cpr_opp2: opp2 {
+ opp-level = <2>;
+ qcom,opp-fuse-level = <2>;
+ };
+ cpr_opp3: opp3 {
+ opp-level = <3>;
+ qcom,opp-fuse-level = <3>;
+ };
+ };
+
+ firmware {
+ scm: scm {
+ compatible = "qcom,scm-qcs404", "qcom,scm";
+ #reset-cells = <1>;
+ };
+ };
+
+ memory at 80000000 {
+ device_type = "memory";
+ /* We expect the bootloader to fill in the size */
+ reg = <0 0x80000000 0 0>;
+ };
+
+ psci {
+ compatible = "arm,psci-1.0";
+ method = "smc";
+ };
+
+ rpm: remoteproc {
+ compatible = "qcom,qcs404-rpm-proc", "qcom,rpm-proc";
+
+ glink-edge {
+ compatible = "qcom,glink-rpm";
+
+ interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+ qcom,rpm-msg-ram = <&rpm_msg_ram>;
+ mboxes = <&apcs_glb 0>;
+
+ rpm_requests: rpm-requests {
+ compatible = "qcom,rpm-qcs404";
+ qcom,glink-channels = "rpm_requests";
+
+ rpmcc: clock-controller {
+ compatible = "qcom,rpmcc-qcs404", "qcom,rpmcc";
+ #clock-cells = <1>;
+ clocks = <&xo_board>;
+ clock-names = "xo";
+ };
+
+ rpmpd: power-controller {
+ compatible = "qcom,qcs404-rpmpd";
+ #power-domain-cells = <1>;
+ operating-points-v2 = <&rpmpd_opp_table>;
+
+ rpmpd_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ rpmpd_opp_ret: opp1 {
+ opp-level = <16>;
+ };
+
+ rpmpd_opp_ret_plus: opp2 {
+ opp-level = <32>;
+ };
+
+ rpmpd_opp_min_svs: opp3 {
+ opp-level = <48>;
+ };
+
+ rpmpd_opp_low_svs: opp4 {
+ opp-level = <64>;
+ };
+
+ rpmpd_opp_svs: opp5 {
+ opp-level = <128>;
+ };
+
+ rpmpd_opp_svs_plus: opp6 {
+ opp-level = <192>;
+ };
+
+ rpmpd_opp_nom: opp7 {
+ opp-level = <256>;
+ };
+
+ rpmpd_opp_nom_plus: opp8 {
+ opp-level = <320>;
+ };
+
+ rpmpd_opp_turbo: opp9 {
+ opp-level = <384>;
+ };
+
+ rpmpd_opp_turbo_no_cpr: opp10 {
+ opp-level = <416>;
+ };
+
+ rpmpd_opp_turbo_plus: opp11 {
+ opp-level = <512>;
+ };
+ };
+ };
+ };
+ };
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ tz_apps_mem: memory at 85900000 {
+ reg = <0 0x85900000 0 0x500000>;
+ no-map;
+ };
+
+ xbl_mem: memory at 85e00000 {
+ reg = <0 0x85e00000 0 0x100000>;
+ no-map;
+ };
+
+ smem_region: memory at 85f00000 {
+ reg = <0 0x85f00000 0 0x200000>;
+ no-map;
+ };
+
+ tz_mem: memory at 86100000 {
+ reg = <0 0x86100000 0 0x300000>;
+ no-map;
+ };
+
+ wlan_fw_mem: memory at 86400000 {
+ reg = <0 0x86400000 0 0x1100000>;
+ no-map;
+ };
+
+ adsp_fw_mem: memory at 87500000 {
+ reg = <0 0x87500000 0 0x1a00000>;
+ no-map;
+ };
+
+ cdsp_fw_mem: memory at 88f00000 {
+ reg = <0 0x88f00000 0 0x600000>;
+ no-map;
+ };
+
+ wlan_msa_mem: memory at 89500000 {
+ reg = <0 0x89500000 0 0x100000>;
+ no-map;
+ };
+
+ uefi_mem: memory at 9f800000 {
+ reg = <0 0x9f800000 0 0x800000>;
+ no-map;
+ };
+ };
+
+ smem {
+ compatible = "qcom,smem";
+
+ memory-region = <&smem_region>;
+ qcom,rpm-msg-ram = <&rpm_msg_ram>;
+
+ hwlocks = <&tcsr_mutex 3>;
+ };
+
+ soc: soc at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0 0 0xffffffff>;
+ compatible = "simple-bus";
+
+ turingcc: clock-controller at 800000 {
+ compatible = "qcom,qcs404-turingcc";
+ reg = <0x00800000 0x30000>;
+ clocks = <&gcc GCC_CDSP_CFG_AHB_CLK>;
+
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+
+ status = "disabled";
+ };
+
+ rpm_msg_ram: sram at 60000 {
+ compatible = "qcom,rpm-msg-ram";
+ reg = <0x00060000 0x6000>;
+ };
+
+ usb3_phy: phy at 78000 {
+ compatible = "qcom,usb-ss-28nm-phy";
+ reg = <0x00078000 0x400>;
+ #phy-cells = <0>;
+ clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
+ <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
+ <&gcc GCC_USB3_PHY_PIPE_CLK>;
+ clock-names = "ref", "ahb", "pipe";
+ resets = <&gcc GCC_USB3_PHY_BCR>,
+ <&gcc GCC_USB3PHY_PHY_BCR>;
+ reset-names = "com", "phy";
+ status = "disabled";
+ };
+
+ usb2_phy_prim: phy at 7a000 {
+ compatible = "qcom,usb-hs-28nm-femtophy";
+ reg = <0x0007a000 0x200>;
+ #phy-cells = <0>;
+ clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
+ <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
+ <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+ clock-names = "ref", "ahb", "sleep";
+ resets = <&gcc GCC_USB_HS_PHY_CFG_AHB_BCR>,
+ <&gcc GCC_USB2A_PHY_BCR>;
+ reset-names = "phy", "por";
+ status = "disabled";
+ };
+
+ usb2_phy_sec: phy at 7c000 {
+ compatible = "qcom,usb-hs-28nm-femtophy";
+ reg = <0x0007c000 0x200>;
+ #phy-cells = <0>;
+ clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
+ <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
+ <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+ clock-names = "ref", "ahb", "sleep";
+ resets = <&gcc GCC_QUSB2_PHY_BCR>,
+ <&gcc GCC_USB2_HS_PHY_ONLY_BCR>;
+ reset-names = "phy", "por";
+ status = "disabled";
+ };
+
+ qfprom: qfprom at a4000 {
+ compatible = "qcom,qcs404-qfprom", "qcom,qfprom";
+ reg = <0x000a4000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ cpr_efuse_speedbin: speedbin at 13c {
+ reg = <0x13c 0x4>;
+ bits = <2 3>;
+ };
+
+ tsens_s0_p1: s0-p1 at 1f8 {
+ reg = <0x1f8 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s0_p2: s0-p2 at 1f8 {
+ reg = <0x1f8 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s1_p1: s1-p1 at 1f9 {
+ reg = <0x1f9 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s1_p2: s1-p2 at 1fa {
+ reg = <0x1fa 0x1>;
+ bits = <2 6>;
+ };
+
+ tsens_s2_p1: s2-p1 at 1fb {
+ reg = <0x1fb 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s2_p2: s2-p2 at 1fb {
+ reg = <0x1fb 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s3_p1: s3-p1 at 1fc {
+ reg = <0x1fc 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s3_p2: s3-p2 at 1fd {
+ reg = <0x1fd 0x1>;
+ bits = <2 6>;
+ };
+
+ tsens_s4_p1: s4-p1 at 1fe {
+ reg = <0x1fe 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s4_p2: s4-p2 at 1fe {
+ reg = <0x1fe 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s5_p1: s5-p1 at 200 {
+ reg = <0x200 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s5_p2: s5-p2 at 200 {
+ reg = <0x200 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s6_p1: s6-p1 at 201 {
+ reg = <0x201 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s6_p2: s6-p2 at 202 {
+ reg = <0x202 0x1>;
+ bits = <2 6>;
+ };
+
+ tsens_s7_p1: s7-p1 at 203 {
+ reg = <0x203 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s7_p2: s7-p2 at 203 {
+ reg = <0x203 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_s8_p1: s8-p1 at 204 {
+ reg = <0x204 0x2>;
+ bits = <4 6>;
+ };
+
+ tsens_s8_p2: s8-p2 at 205 {
+ reg = <0x205 0x1>;
+ bits = <2 6>;
+ };
+
+ tsens_s9_p1: s9-p1 at 206 {
+ reg = <0x206 0x1>;
+ bits = <0 6>;
+ };
+
+ tsens_s9_p2: s9-p2 at 206 {
+ reg = <0x206 0x2>;
+ bits = <6 6>;
+ };
+
+ tsens_mode: mode at 208 {
+ reg = <0x208 1>;
+ bits = <0 3>;
+ };
+
+ tsens_base1: base1 at 208 {
+ reg = <0x208 2>;
+ bits = <3 8>;
+ };
+
+ tsens_base2: base2 at 208 {
+ reg = <0x209 2>;
+ bits = <3 8>;
+ };
+
+ cpr_efuse_quot_offset1: qoffset1 at 231 {
+ reg = <0x231 0x4>;
+ bits = <4 7>;
+ };
+ cpr_efuse_quot_offset2: qoffset2 at 232 {
+ reg = <0x232 0x4>;
+ bits = <3 7>;
+ };
+ cpr_efuse_quot_offset3: qoffset3 at 233 {
+ reg = <0x233 0x4>;
+ bits = <2 7>;
+ };
+ cpr_efuse_init_voltage1: ivoltage1 at 229 {
+ reg = <0x229 0x4>;
+ bits = <4 6>;
+ };
+ cpr_efuse_init_voltage2: ivoltage2 at 22a {
+ reg = <0x22a 0x4>;
+ bits = <2 6>;
+ };
+ cpr_efuse_init_voltage3: ivoltage3 at 22b {
+ reg = <0x22b 0x4>;
+ bits = <0 6>;
+ };
+ cpr_efuse_quot1: quot1 at 22b {
+ reg = <0x22b 0x4>;
+ bits = <6 12>;
+ };
+ cpr_efuse_quot2: quot2 at 22d {
+ reg = <0x22d 0x4>;
+ bits = <2 12>;
+ };
+ cpr_efuse_quot3: quot3 at 230 {
+ reg = <0x230 0x4>;
+ bits = <0 12>;
+ };
+ cpr_efuse_ring1: ring1 at 228 {
+ reg = <0x228 0x4>;
+ bits = <0 3>;
+ };
+ cpr_efuse_ring2: ring2 at 228 {
+ reg = <0x228 0x4>;
+ bits = <4 3>;
+ };
+ cpr_efuse_ring3: ring3 at 229 {
+ reg = <0x229 0x4>;
+ bits = <0 3>;
+ };
+ cpr_efuse_revision: revision at 218 {
+ reg = <0x218 0x4>;
+ bits = <3 3>;
+ };
+ };
+
+ rng: rng at e3000 {
+ compatible = "qcom,prng-ee";
+ reg = <0x000e3000 0x1000>;
+ clocks = <&gcc GCC_PRNG_AHB_CLK>;
+ clock-names = "core";
+ };
+
+ bimc: interconnect at 400000 {
+ reg = <0x00400000 0x80000>;
+ compatible = "qcom,qcs404-bimc";
+ #interconnect-cells = <1>;
+ clock-names = "bus", "bus_a";
+ clocks = <&rpmcc RPM_SMD_BIMC_CLK>,
+ <&rpmcc RPM_SMD_BIMC_A_CLK>;
+ };
+
+ tsens: thermal-sensor at 4a9000 {
+ compatible = "qcom,qcs404-tsens", "qcom,tsens-v1";
+ reg = <0x004a9000 0x1000>, /* TM */
+ <0x004a8000 0x1000>; /* SROT */
+ nvmem-cells = <&tsens_mode>,
+ <&tsens_base1>, <&tsens_base2>,
+ <&tsens_s0_p1>, <&tsens_s0_p2>,
+ <&tsens_s1_p1>, <&tsens_s1_p2>,
+ <&tsens_s2_p1>, <&tsens_s2_p2>,
+ <&tsens_s3_p1>, <&tsens_s3_p2>,
+ <&tsens_s4_p1>, <&tsens_s4_p2>,
+ <&tsens_s5_p1>, <&tsens_s5_p2>,
+ <&tsens_s6_p1>, <&tsens_s6_p2>,
+ <&tsens_s7_p1>, <&tsens_s7_p2>,
+ <&tsens_s8_p1>, <&tsens_s8_p2>,
+ <&tsens_s9_p1>, <&tsens_s9_p2>;
+ nvmem-cell-names = "mode",
+ "base1", "base2",
+ "s0_p1", "s0_p2",
+ "s1_p1", "s1_p2",
+ "s2_p1", "s2_p2",
+ "s3_p1", "s3_p2",
+ "s4_p1", "s4_p2",
+ "s5_p1", "s5_p2",
+ "s6_p1", "s6_p2",
+ "s7_p1", "s7_p2",
+ "s8_p1", "s8_p2",
+ "s9_p1", "s9_p2";
+ #qcom,sensors = <10>;
+ interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow";
+ #thermal-sensor-cells = <1>;
+ };
+
+ pcnoc: interconnect at 500000 {
+ reg = <0x00500000 0x15080>;
+ compatible = "qcom,qcs404-pcnoc";
+ #interconnect-cells = <1>;
+ clock-names = "bus", "bus_a";
+ clocks = <&rpmcc RPM_SMD_PNOC_CLK>,
+ <&rpmcc RPM_SMD_PNOC_A_CLK>;
+ };
+
+ snoc: interconnect at 580000 {
+ reg = <0x00580000 0x23080>;
+ compatible = "qcom,qcs404-snoc";
+ #interconnect-cells = <1>;
+ clock-names = "bus", "bus_a";
+ clocks = <&rpmcc RPM_SMD_SNOC_CLK>,
+ <&rpmcc RPM_SMD_SNOC_A_CLK>;
+ };
+
+ remoteproc_cdsp: remoteproc at b00000 {
+ compatible = "qcom,qcs404-cdsp-pas";
+ reg = <0x00b00000 0x4040>;
+
+ interrupts-extended = <&intc GIC_SPI 229 IRQ_TYPE_EDGE_RISING>,
+ <&cdsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&cdsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&cdsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&cdsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&xo_board>;
+ clock-names = "xo";
+
+ /*
+ * If the node was using the PIL binding, then include properties:
+ * clocks = <&xo_board>,
+ * <&gcc GCC_CDSP_CFG_AHB_CLK>,
+ * <&gcc GCC_CDSP_TBU_CLK>,
+ * <&gcc GCC_BIMC_CDSP_CLK>,
+ * <&turingcc TURING_WRAPPER_AON_CLK>,
+ * <&turingcc TURING_Q6SS_AHBS_AON_CLK>,
+ * <&turingcc TURING_Q6SS_AHBM_AON_CLK>,
+ * <&turingcc TURING_Q6SS_Q6_AXIM_CLK>;
+ * clock-names = "xo",
+ * "sway",
+ * "tbu",
+ * "bimc",
+ * "ahb_aon",
+ * "q6ss_slave",
+ * "q6ss_master",
+ * "q6_axim";
+ * resets = <&gcc GCC_CDSP_RESTART>;
+ * reset-names = "restart";
+ * qcom,halt-regs = <&tcsr 0x19004>;
+ */
+
+ memory-region = <&cdsp_fw_mem>;
+
+ qcom,smem-states = <&cdsp_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts = <GIC_SPI 141 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,remote-pid = <5>;
+ mboxes = <&apcs_glb 12>;
+
+ label = "cdsp";
+ };
+ };
+
+ usb3: usb at 7678800 {
+ compatible = "qcom,qcs404-dwc3", "qcom,dwc3";
+ reg = <0x07678800 0x400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ clocks = <&gcc GCC_USB30_MASTER_CLK>,
+ <&gcc GCC_SYS_NOC_USB3_CLK>,
+ <&gcc GCC_USB30_SLEEP_CLK>,
+ <&gcc GCC_USB30_MOCK_UTMI_CLK>;
+ clock-names = "core", "iface", "sleep", "mock_utmi";
+ assigned-clocks = <&gcc GCC_USB20_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB30_MASTER_CLK>;
+ assigned-clock-rates = <19200000>, <200000000>;
+ status = "disabled";
+
+ usb3_dwc3: usb at 7580000 {
+ compatible = "snps,dwc3";
+ reg = <0x07580000 0xcd00>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb2_phy_prim>, <&usb3_phy>;
+ phy-names = "usb2-phy", "usb3-phy";
+ snps,has-lpm-erratum;
+ snps,hird-threshold = /bits/ 8 <0x10>;
+ snps,usb3_lpm_capable;
+ dr_mode = "otg";
+ };
+ };
+
+ usb2: usb at 79b8800 {
+ compatible = "qcom,qcs404-dwc3", "qcom,dwc3";
+ reg = <0x079b8800 0x400>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>,
+ <&gcc GCC_PCNOC_USB2_CLK>,
+ <&gcc GCC_USB_HS_INACTIVITY_TIMERS_CLK>,
+ <&gcc GCC_USB20_MOCK_UTMI_CLK>;
+ clock-names = "core", "iface", "sleep", "mock_utmi";
+ assigned-clocks = <&gcc GCC_USB20_MOCK_UTMI_CLK>,
+ <&gcc GCC_USB_HS_SYSTEM_CLK>;
+ assigned-clock-rates = <19200000>, <133333333>;
+ status = "disabled";
+
+ usb at 78c0000 {
+ compatible = "snps,dwc3";
+ reg = <0x078c0000 0xcc00>;
+ interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+ phys = <&usb2_phy_sec>;
+ phy-names = "usb2-phy";
+ snps,has-lpm-erratum;
+ snps,hird-threshold = /bits/ 8 <0x10>;
+ snps,usb3_lpm_capable;
+ dr_mode = "peripheral";
+ };
+ };
+
+ tlmm: pinctrl at 1000000 {
+ compatible = "qcom,qcs404-pinctrl";
+ reg = <0x01000000 0x200000>,
+ <0x01300000 0x200000>,
+ <0x07b00000 0x200000>;
+ reg-names = "south", "north", "east";
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-ranges = <&tlmm 0 0 120>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ blsp1_i2c0_default: blsp1-i2c0-default-state {
+ pins = "gpio32", "gpio33";
+ function = "blsp_i2c0";
+ };
+
+ blsp1_i2c1_default: blsp1-i2c1-default-state {
+ pins = "gpio24", "gpio25";
+ function = "blsp_i2c1";
+ };
+
+ blsp1_i2c2_default: blsp1-i2c2-default-state {
+ sda-pins {
+ pins = "gpio19";
+ function = "blsp_i2c_sda_a2";
+ };
+
+ scl-pins {
+ pins = "gpio20";
+ function = "blsp_i2c_scl_a2";
+ };
+ };
+
+ blsp1_i2c3_default: blsp1-i2c3-default-state {
+ pins = "gpio84", "gpio85";
+ function = "blsp_i2c3";
+ };
+
+ blsp1_i2c4_default: blsp1-i2c4-default-state {
+ pins = "gpio117", "gpio118";
+ function = "blsp_i2c4";
+ };
+
+ blsp1_uart0_default: blsp1-uart0-default-state {
+ pins = "gpio30", "gpio31", "gpio32", "gpio33";
+ function = "blsp_uart0";
+ };
+
+ blsp1_uart1_default: blsp1-uart1-default-state {
+ pins = "gpio22", "gpio23";
+ function = "blsp_uart1";
+ };
+
+ blsp1_uart2_default: blsp1-uart2-default-state {
+ rx-pins {
+ pins = "gpio18";
+ function = "blsp_uart_rx_a2";
+ };
+
+ tx-pins {
+ pins = "gpio17";
+ function = "blsp_uart_tx_a2";
+ };
+ };
+
+ blsp1_uart3_default: blsp1-uart3-default-state {
+ cts-pins {
+ pins = "gpio84";
+ function = "blsp_uart3";
+ };
+
+ rts-tx-pins {
+ pins = "gpio85", "gpio82";
+ function = "blsp_uart3";
+ };
+
+ rx-pins {
+ pins = "gpio83";
+ function = "blsp_uart3";
+ };
+ };
+
+ blsp2_i2c0_default: blsp2-i2c0-default-state {
+ pins = "gpio28", "gpio29";
+ function = "blsp_i2c5";
+ };
+
+ blsp1_spi0_default: blsp1-spi0-default-state {
+ pins = "gpio30", "gpio31", "gpio32", "gpio33";
+ function = "blsp_spi0";
+ };
+
+ blsp1_spi1_default: blsp1-spi1-default-state {
+ mosi-pins {
+ pins = "gpio22";
+ function = "blsp_spi_mosi_a1";
+ };
+
+ miso-pins {
+ pins = "gpio23";
+ function = "blsp_spi_miso_a1";
+ };
+
+ cs-n-pins {
+ pins = "gpio24";
+ function = "blsp_spi_cs_n_a1";
+ };
+
+ clk-pins {
+ pins = "gpio25";
+ function = "blsp_spi_clk_a1";
+ };
+ };
+
+ blsp1_spi2_default: blsp1-spi2-default-state {
+ pins = "gpio17", "gpio18", "gpio19", "gpio20";
+ function = "blsp_spi2";
+ };
+
+ blsp1_spi3_default: blsp1-spi3-default-state {
+ pins = "gpio82", "gpio83", "gpio84", "gpio85";
+ function = "blsp_spi3";
+ };
+
+ blsp1_spi4_default: blsp1-spi4-default-state {
+ pins = "gpio37", "gpio38", "gpio117", "gpio118";
+ function = "blsp_spi4";
+ };
+
+ blsp2_spi0_default: blsp2-spi0-default-state {
+ pins = "gpio26", "gpio27", "gpio28", "gpio29";
+ function = "blsp_spi5";
+ };
+
+ blsp2_uart0_default: blsp2-uart0-default-state {
+ pins = "gpio26", "gpio27", "gpio28", "gpio29";
+ function = "blsp_uart5";
+ };
+ };
+
+ gcc: clock-controller at 1800000 {
+ compatible = "qcom,gcc-qcs404";
+ reg = <0x01800000 0x80000>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ #power-domain-cells = <1>;
+
+ clocks = <&xo_board>,
+ <&sleep_clk>,
+ <&pcie_phy>,
+ <0>,
+ <0>,
+ <0>;
+
+ assigned-clocks = <&gcc GCC_APSS_AHB_CLK_SRC>;
+ assigned-clock-rates = <19200000>;
+ };
+
+ tcsr_mutex: hwlock at 1905000 {
+ compatible = "qcom,tcsr-mutex";
+ reg = <0x01905000 0x20000>;
+ #hwlock-cells = <1>;
+ };
+
+ tcsr: syscon at 1937000 {
+ compatible = "qcom,qcs404-tcsr", "syscon";
+ reg = <0x01937000 0x25000>;
+ };
+
+ sram at 290000 {
+ compatible = "qcom,rpm-stats";
+ reg = <0x00290000 0x10000>;
+ };
+
+ spmi_bus: spmi at 200f000 {
+ compatible = "qcom,spmi-pmic-arb";
+ reg = <0x0200f000 0x001000>,
+ <0x02400000 0x800000>,
+ <0x02c00000 0x800000>,
+ <0x03800000 0x200000>,
+ <0x0200a000 0x002100>;
+ reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+ interrupt-names = "periph_irq";
+ interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+ qcom,ee = <0>;
+ qcom,channel = <0>;
+ #address-cells = <2>;
+ #size-cells = <0>;
+ interrupt-controller;
+ #interrupt-cells = <4>;
+ };
+
+ remoteproc_wcss: remoteproc at 7400000 {
+ compatible = "qcom,qcs404-wcss-pas";
+ reg = <0x07400000 0x4040>;
+
+ interrupts-extended = <&intc GIC_SPI 153 IRQ_TYPE_EDGE_RISING>,
+ <&wcss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&wcss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&wcss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&wcss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&xo_board>;
+ clock-names = "xo";
+
+ memory-region = <&wlan_fw_mem>;
+
+ qcom,smem-states = <&wcss_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,remote-pid = <1>;
+ mboxes = <&apcs_glb 16>;
+
+ label = "wcss";
+ };
+ };
+
+ pcie_phy: phy at 7786000 {
+ compatible = "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy";
+ reg = <0x07786000 0xb8>;
+
+ clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+ resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>,
+ <&gcc GCC_PCIE_0_PIPE_ARES>;
+ reset-names = "phy", "pipe";
+
+ clock-output-names = "pcie_0_pipe_clk";
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ sdcc1: mmc at 7804000 {
+ compatible = "qcom,qcs404-sdhci", "qcom,sdhci-msm-v5";
+ reg = <0x07804000 0x1000>, <0x7805000 0x1000>;
+ reg-names = "hc", "cqhci";
+
+ interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq", "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+ <&gcc GCC_SDCC1_APPS_CLK>,
+ <&xo_board>;
+ clock-names = "iface", "core", "xo";
+
+ status = "disabled";
+ };
+
+ blsp1_dma: dma-controller at 7884000 {
+ compatible = "qcom,bam-v1.7.0";
+ reg = <0x07884000 0x25000>;
+ interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ status = "okay";
+ };
+
+ blsp1_uart0: serial at 78af000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078af000 0x200>;
+ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART0_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp1_dma 0>, <&blsp1_dma 1>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart0_default>;
+ status = "disabled";
+ };
+
+ blsp1_uart1: serial at 78b0000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078b0000 0x200>;
+ interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp1_dma 2>, <&blsp1_dma 3>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart1_default>;
+ status = "disabled";
+ };
+
+ blsp1_uart2: serial at 78b1000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078b1000 0x200>;
+ interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp1_dma 4>, <&blsp1_dma 5>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart2_default>;
+ status = "okay";
+ };
+
+ ethernet: ethernet at 7a80000 {
+ compatible = "qcom,qcs404-ethqos";
+ reg = <0x07a80000 0x10000>,
+ <0x07a96000 0x100>;
+ reg-names = "stmmaceth", "rgmii";
+ clock-names = "stmmaceth", "pclk", "ptp_ref", "rgmii";
+ clocks = <&gcc GCC_ETH_AXI_CLK>,
+ <&gcc GCC_ETH_SLAVE_AHB_CLK>,
+ <&gcc GCC_ETH_PTP_CLK>,
+ <&gcc GCC_ETH_RGMII_CLK>;
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq", "eth_lpi";
+
+ snps,tso;
+ rx-fifo-depth = <4096>;
+ tx-fifo-depth = <4096>;
+
+ status = "disabled";
+ };
+
+ wifi: wifi at a000000 {
+ compatible = "qcom,wcn3990-wifi";
+ reg = <0xa000000 0x800000>;
+ reg-names = "membase";
+ memory-region = <&wlan_msa_mem>;
+ interrupts = <GIC_SPI 277 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ blsp1_uart3: serial at 78b2000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x078b2000 0x200>;
+ interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp1_dma 6>, <&blsp1_dma 7>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_uart3_default>;
+ status = "disabled";
+ };
+
+ blsp1_i2c0: i2c at 78b5000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b5000 0x600>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP0_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_i2c0_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_spi0: spi at 78b5000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b5000 0x600>;
+ interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP0_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_spi0_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_i2c1: i2c at 78b6000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b6000 0x600>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_i2c1_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_spi1: spi at 78b6000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b6000 0x600>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_spi1_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_i2c2: i2c at 78b7000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b7000 0x600>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_i2c2_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_spi2: spi at 78b7000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b7000 0x600>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_spi2_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_i2c3: i2c at 78b8000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b8000 0x600>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_i2c3_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_spi3: spi at 78b8000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b8000 0x600>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_spi3_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_i2c4: i2c at 78b9000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x078b9000 0x600>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_i2c4_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp1_spi4: spi at 78b9000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x078b9000 0x600>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp1_spi4_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp2_dma: dma-controller at 7ac4000 {
+ compatible = "qcom,bam-v1.7.0";
+ reg = <0x07ac4000 0x17000>;
+ interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "bam_clk";
+ #dma-cells = <1>;
+ qcom,ee = <0>;
+ status = "disabled";
+ };
+
+ blsp2_uart0: serial at 7aef000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x07aef000 0x200>;
+ interrupts = <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP2_UART0_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
+ dmas = <&blsp2_dma 0>, <&blsp2_dma 1>;
+ dma-names = "tx", "rx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp2_uart0_default>;
+ status = "disabled";
+ };
+
+ blsp2_i2c0: i2c at 7af5000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x07af5000 0x600>;
+ interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP2_QUP0_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp2_i2c0_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ blsp2_spi0: spi at 7af5000 {
+ compatible = "qcom,spi-qup-v2.2.1";
+ reg = <0x07af5000 0x600>;
+ interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP2_QUP0_SPI_APPS_CLK>,
+ <&gcc GCC_BLSP2_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default";
+ pinctrl-0 = <&blsp2_spi0_default>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ sram at 8600000 {
+ compatible = "qcom,qcs404-imem", "syscon", "simple-mfd";
+ reg = <0x08600000 0x1000>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ranges = <0 0x08600000 0x1000>;
+
+ pil-reloc at 94c {
+ compatible = "qcom,pil-reloc-info";
+ reg = <0x94c 0xc8>;
+ };
+ };
+
+ intc: interrupt-controller at b000000 {
+ compatible = "qcom,msm-qgic2";
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ reg = <0x0b000000 0x1000>,
+ <0x0b002000 0x1000>;
+ };
+
+ apcs_glb: mailbox at b011000 {
+ compatible = "qcom,qcs404-apcs-apps-global",
+ "qcom,msm8916-apcs-kpss-global", "syscon";
+ reg = <0x0b011000 0x1000>;
+ #mbox-cells = <1>;
+ clocks = <&apcs_hfpll>, <&gcc GCC_GPLL0_AO_OUT_MAIN>;
+ clock-names = "pll", "aux";
+ #clock-cells = <0>;
+ };
+
+ apcs_hfpll: clock-controller at b016000 {
+ compatible = "qcom,hfpll";
+ reg = <0x0b016000 0x30>;
+ #clock-cells = <0>;
+ clock-output-names = "apcs_hfpll";
+ clocks = <&xo_board>;
+ clock-names = "xo";
+ };
+
+ watchdog at b017000 {
+ compatible = "qcom,apss-wdt-qcs404", "qcom,kpss-wdt";
+ reg = <0x0b017000 0x1000>;
+ clocks = <&sleep_clk>;
+ };
+
+ cpr: power-controller at b018000 {
+ compatible = "qcom,qcs404-cpr", "qcom,cpr";
+ reg = <0x0b018000 0x1000>;
+ interrupts = <0 15 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xo_board>;
+ clock-names = "ref";
+ vdd-apc-supply = <&pms405_s3>;
+ #power-domain-cells = <0>;
+ operating-points-v2 = <&cpr_opp_table>;
+ acc-syscon = <&tcsr>;
+
+ nvmem-cells = <&cpr_efuse_quot_offset1>,
+ <&cpr_efuse_quot_offset2>,
+ <&cpr_efuse_quot_offset3>,
+ <&cpr_efuse_init_voltage1>,
+ <&cpr_efuse_init_voltage2>,
+ <&cpr_efuse_init_voltage3>,
+ <&cpr_efuse_quot1>,
+ <&cpr_efuse_quot2>,
+ <&cpr_efuse_quot3>,
+ <&cpr_efuse_ring1>,
+ <&cpr_efuse_ring2>,
+ <&cpr_efuse_ring3>,
+ <&cpr_efuse_revision>;
+ nvmem-cell-names = "cpr_quotient_offset1",
+ "cpr_quotient_offset2",
+ "cpr_quotient_offset3",
+ "cpr_init_voltage1",
+ "cpr_init_voltage2",
+ "cpr_init_voltage3",
+ "cpr_quotient1",
+ "cpr_quotient2",
+ "cpr_quotient3",
+ "cpr_ring_osc1",
+ "cpr_ring_osc2",
+ "cpr_ring_osc3",
+ "cpr_fuse_revision";
+ };
+
+ timer at b120000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ compatible = "arm,armv7-timer-mem";
+ reg = <0x0b120000 0x1000>;
+ clock-frequency = <19200000>;
+
+ frame at b121000 {
+ frame-number = <0>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b121000 0x1000>,
+ <0x0b122000 0x1000>;
+ };
+
+ frame at b123000 {
+ frame-number = <1>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b123000 0x1000>;
+ status = "disabled";
+ };
+
+ frame at b124000 {
+ frame-number = <2>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b124000 0x1000>;
+ status = "disabled";
+ };
+
+ frame at b125000 {
+ frame-number = <3>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b125000 0x1000>;
+ status = "disabled";
+ };
+
+ frame at b126000 {
+ frame-number = <4>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b126000 0x1000>;
+ status = "disabled";
+ };
+
+ frame at b127000 {
+ frame-number = <5>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0xb127000 0x1000>;
+ status = "disabled";
+ };
+
+ frame at b128000 {
+ frame-number = <6>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x0b128000 0x1000>;
+ status = "disabled";
+ };
+ };
+
+ remoteproc_adsp: remoteproc at c700000 {
+ compatible = "qcom,qcs404-adsp-pas";
+ reg = <0x0c700000 0x4040>;
+
+ interrupts-extended = <&intc GIC_SPI 293 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ clocks = <&xo_board>;
+ clock-names = "xo";
+
+ memory-region = <&adsp_fw_mem>;
+
+ qcom,smem-states = <&adsp_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ glink-edge {
+ interrupts = <GIC_SPI 289 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,remote-pid = <2>;
+ mboxes = <&apcs_glb 8>;
+
+ label = "adsp";
+ };
+ };
+
+ pcie: pci at 10000000 {
+ compatible = "qcom,pcie-qcs404";
+ reg = <0x10000000 0xf1d>,
+ <0x10000f20 0xa8>,
+ <0x07780000 0x2000>,
+ <0x10001000 0x2000>;
+ reg-names = "dbi", "elbi", "parf", "config";
+ device_type = "pci";
+ linux,pci-domain = <0>;
+ bus-range = <0x00 0xff>;
+ num-lanes = <1>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x81000000 0x0 0x00000000 0x10003000 0x0 0x00010000>, /* I/O */
+ <0x82000000 0x0 0x10013000 0x10013000 0x0 0x007ed000>; /* memory */
+
+ interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "msi";
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0x7>;
+ interrupt-map = <0 0 0 1 &intc GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+ <0 0 0 2 &intc GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+ <0 0 0 3 &intc GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+ <0 0 0 4 &intc GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+ clocks = <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+ <&gcc GCC_PCIE_0_AUX_CLK>,
+ <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+ <&gcc GCC_PCIE_0_SLV_AXI_CLK>;
+ clock-names = "iface", "aux", "master_bus", "slave_bus";
+
+ resets = <&gcc GCC_PCIE_0_AXI_MASTER_ARES>,
+ <&gcc GCC_PCIE_0_AXI_SLAVE_ARES>,
+ <&gcc GCC_PCIE_0_AXI_MASTER_STICKY_ARES>,
+ <&gcc GCC_PCIE_0_CORE_STICKY_ARES>,
+ <&gcc GCC_PCIE_0_BCR>,
+ <&gcc GCC_PCIE_0_AHB_ARES>;
+ reset-names = "axi_m",
+ "axi_s",
+ "axi_m_sticky",
+ "pipe_sticky",
+ "pwr",
+ "ahb";
+
+ phys = <&pcie_phy>;
+ phy-names = "pciephy";
+
+ status = "disabled";
+ };
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 2 0xff08>,
+ <GIC_PPI 3 0xff08>,
+ <GIC_PPI 4 0xff08>,
+ <GIC_PPI 1 0xff08>;
+ };
+
+ smp2p-adsp {
+ compatible = "qcom,smp2p";
+ qcom,smem = <443>, <429>;
+ interrupts = <GIC_SPI 291 IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&apcs_glb 10>;
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <2>;
+
+ adsp_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ adsp_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ smp2p-cdsp {
+ compatible = "qcom,smp2p";
+ qcom,smem = <94>, <432>;
+ interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&apcs_glb 14>;
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <5>;
+
+ cdsp_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ cdsp_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ smp2p-wcss {
+ compatible = "qcom,smp2p";
+ qcom,smem = <435>, <428>;
+ interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;
+ mboxes = <&apcs_glb 18>;
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <1>;
+
+ wcss_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ wcss_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ thermal-zones {
+ aoss-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 0>;
+
+ trips {
+ aoss_alert0: trip-point0 {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ q6-hvx-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 1>;
+
+ trips {
+ q6_hvx_alert0: trip-point0 {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ lpass-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 2>;
+
+ trips {
+ lpass_alert0: trip-point0 {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ wlan-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 3>;
+
+ trips {
+ wlan_alert0: trip-point0 {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+
+ cluster-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 4>;
+
+ trips {
+ cluster_alert0: trip-point0 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ cluster_alert1: trip-point1 {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cluster_crit: cluster-crit {
+ temperature = <120000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ cooling-maps {
+ map0 {
+ trip = <&cluster_alert1>;
+ cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ cpu0-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 5>;
+
+ trips {
+ cpu0_alert0: trip-point0 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ cpu0_alert1: trip-point1 {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu0_crit: cpu-crit {
+ temperature = <120000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ cooling-maps {
+ map0 {
+ trip = <&cpu0_alert1>;
+ cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ cpu1-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 6>;
+
+ trips {
+ cpu1_alert0: trip-point0 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ cpu1_alert1: trip-point1 {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu1_crit: cpu-crit {
+ temperature = <120000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ cooling-maps {
+ map0 {
+ trip = <&cpu1_alert1>;
+ cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ cpu2-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 7>;
+
+ trips {
+ cpu2_alert0: trip-point0 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ cpu2_alert1: trip-point1 {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu2_crit: cpu-crit {
+ temperature = <120000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ cooling-maps {
+ map0 {
+ trip = <&cpu2_alert1>;
+ cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ cpu3-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 8>;
+
+ trips {
+ cpu3_alert0: trip-point0 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ cpu3_alert1: trip-point1 {
+ temperature = <105000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu3_crit: cpu-crit {
+ temperature = <120000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ cooling-maps {
+ map0 {
+ trip = <&cpu3_alert1>;
+ cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+ };
+
+ gpu-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 9>;
+
+ trips {
+ gpu_alert0: trip-point0 {
+ temperature = <95000>;
+ hysteresis = <2000>;
+ type = "hot";
+ };
+ };
+ };
+ };
+};
--
2.43.1
More information about the U-Boot
mailing list