[PATCH v4 28/39] dts: sdm845: import supporting dtsi files
Sumit Garg
sumit.garg at linaro.org
Tue Feb 20 15:03:34 CET 2024
On Fri, 16 Feb 2024 at 02:22, Caleb Connolly <caleb.connolly at linaro.org> wrote:
>
> Import the PM8998 and PMI8998 PMIC DTSI files from Linux as well
> as the common audio codec in preperation for replacing board DTS files
s/preperation/preparation/
> with upstream.
>
> Taken from kernel tag v6.7
>
> Reviewed-by: Neil Armstrong <neil.armstrong at linaro.org>
> Signed-off-by: Caleb Connolly <caleb.connolly at linaro.org>
> ---
> arch/arm/dts/pm8998.dtsi | 130 +++++++++++++++++++++++++++++++++++++++
> arch/arm/dts/pmi8998.dtsi | 98 +++++++++++++++++++++++++++++
> arch/arm/dts/sdm845-wcd9340.dtsi | 86 ++++++++++++++++++++++++++
> 3 files changed, 314 insertions(+)
>
Reviewed-by: Sumit Garg <sumit.garg at linaro.org>
-Sumit
> diff --git a/arch/arm/dts/pm8998.dtsi b/arch/arm/dts/pm8998.dtsi
> new file mode 100644
> index 000000000000..3f82715392c6
> --- /dev/null
> +++ b/arch/arm/dts/pm8998.dtsi
> @@ -0,0 +1,130 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/* Copyright 2018 Google LLC. */
> +
> +#include <dt-bindings/iio/qcom,spmi-vadc.h>
> +#include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> + thermal-zones {
> + pm8998-thermal {
> + polling-delay-passive = <250>;
> + polling-delay = <1000>;
> +
> + thermal-sensors = <&pm8998_temp>;
> +
> + trips {
> + pm8998_alert0: pm8998-alert0 {
> + temperature = <105000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> + pm8998_crit: pm8998-crit {
> + temperature = <125000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> + };
> + };
> +};
> +
> +&spmi_bus {
> + pm8998_lsid0: pmic at 0 {
> + compatible = "qcom,pm8998", "qcom,spmi-pmic";
> + reg = <0x0 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pm8998_pon: pon at 800 {
> + compatible = "qcom,pm8998-pon";
> +
> + reg = <0x800>;
> + mode-bootloader = <0x2>;
> + mode-recovery = <0x1>;
> +
> + pm8998_pwrkey: pwrkey {
> + compatible = "qcom,pm8941-pwrkey";
> + interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
> + debounce = <15625>;
> + bias-pull-up;
> + linux,code = <KEY_POWER>;
> + };
> +
> + pm8998_resin: resin {
> + compatible = "qcom,pm8941-resin";
> + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
> + debounce = <15625>;
> + bias-pull-up;
> + status = "disabled";
> + };
> + };
> +
> + pm8998_temp: temp-alarm at 2400 {
> + compatible = "qcom,spmi-temp-alarm";
> + reg = <0x2400>;
> + interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
> + io-channels = <&pm8998_adc ADC5_DIE_TEMP>;
> + io-channel-names = "thermal";
> + #thermal-sensor-cells = <0>;
> + };
> +
> + pm8998_coincell: charger at 2800 {
> + compatible = "qcom,pm8998-coincell", "qcom,pm8941-coincell";
> + reg = <0x2800>;
> +
> + status = "disabled";
> + };
> +
> + pm8998_adc: adc at 3100 {
> + compatible = "qcom,spmi-adc-rev2";
> + reg = <0x3100>;
> + interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #io-channel-cells = <1>;
> +
> + channel at 6 {
> + reg = <ADC5_DIE_TEMP>;
> + label = "die_temp";
> + };
> + };
> +
> + pm8998_adc_tm: adc-tm at 3400 {
> + compatible = "qcom,spmi-adc-tm-hc";
> + reg = <0x3400>;
> + interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
> + #thermal-sensor-cells = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "disabled";
> + };
> +
> + rtc at 6000 {
> + compatible = "qcom,pm8941-rtc";
> + reg = <0x6000>, <0x6100>;
> + reg-names = "rtc", "alarm";
> + interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
> + };
> +
> + pm8998_gpios: gpio at c000 {
> + compatible = "qcom,pm8998-gpio", "qcom,spmi-gpio";
> + reg = <0xc000>;
> + gpio-controller;
> + gpio-ranges = <&pm8998_gpios 0 0 26>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + };
> +
> + pm8998_lsid1: pmic at 1 {
> + compatible = "qcom,pm8998", "qcom,spmi-pmic";
> + reg = <0x1 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +};
> diff --git a/arch/arm/dts/pmi8998.dtsi b/arch/arm/dts/pmi8998.dtsi
> new file mode 100644
> index 000000000000..cd3f0790fd42
> --- /dev/null
> +++ b/arch/arm/dts/pmi8998.dtsi
> @@ -0,0 +1,98 @@
> +// SPDX-License-Identifier: GPL-2.0
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +&spmi_bus {
> + pmi8998_lsid0: pmic at 2 {
> + compatible = "qcom,pmi8998", "qcom,spmi-pmic";
> + reg = <0x2 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pmi8998_charger: charger at 1000 {
> + compatible = "qcom,pmi8998-charger";
> + reg = <0x1000>;
> +
> + interrupts = <0x2 0x13 0x4 IRQ_TYPE_EDGE_BOTH>,
> + <0x2 0x12 0x2 IRQ_TYPE_EDGE_BOTH>,
> + <0x2 0x16 0x1 IRQ_TYPE_EDGE_RISING>,
> + <0x2 0x13 0x6 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "usb-plugin",
> + "bat-ov",
> + "wdog-bark",
> + "usbin-icl-change";
> +
> + io-channels = <&pmi8998_rradc 3>,
> + <&pmi8998_rradc 4>;
> + io-channel-names = "usbin_i", "usbin_v";
> +
> + status = "disabled";
> + };
> +
> + pmi8998_gpios: gpio at c000 {
> + compatible = "qcom,pmi8998-gpio", "qcom,spmi-gpio";
> + reg = <0xc000>;
> + gpio-controller;
> + gpio-ranges = <&pmi8998_gpios 0 0 14>;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + pmi8998_rradc: adc at 4500 {
> + compatible = "qcom,pmi8998-rradc";
> + reg = <0x4500>;
> + #io-channel-cells = <1>;
> + };
> + };
> +
> + pmi8998_lsid1: pmic at 3 {
> + compatible = "qcom,pmi8998", "qcom,spmi-pmic";
> + reg = <0x3 SPMI_USID>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + labibb {
> + compatible = "qcom,pmi8998-lab-ibb";
> +
> + ibb: ibb {
> + interrupts = <0x3 0xdc 0x2 IRQ_TYPE_EDGE_RISING>,
> + <0x3 0xdc 0x0 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "sc-err", "ocp";
> + };
> +
> + lab: lab {
> + interrupts = <0x3 0xde 0x1 IRQ_TYPE_EDGE_RISING>,
> + <0x3 0xde 0x0 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-names = "sc-err", "ocp";
> + };
> + };
> +
> + pmi8998_lpg: pwm {
> + compatible = "qcom,pmi8998-lpg";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #pwm-cells = <2>;
> +
> + status = "disabled";
> + };
> +
> + pmi8998_flash: led-controller at d300 {
> + compatible = "qcom,pmi8998-flash-led", "qcom,spmi-flash-led";
> + reg = <0xd300>;
> + status = "disabled";
> + };
> +
> + pmi8998_wled: leds at d800 {
> + compatible = "qcom,pmi8998-wled";
> + reg = <0xd800>, <0xd900>;
> + interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>,
> + <0x3 0xd8 0x2 IRQ_TYPE_EDGE_RISING>;
> + interrupt-names = "ovp", "short";
> + label = "backlight";
> +
> + status = "disabled";
> + };
> + };
> +};
> diff --git a/arch/arm/dts/sdm845-wcd9340.dtsi b/arch/arm/dts/sdm845-wcd9340.dtsi
> new file mode 100644
> index 000000000000..c15d48860646
> --- /dev/null
> +++ b/arch/arm/dts/sdm845-wcd9340.dtsi
> @@ -0,0 +1,86 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * SDM845 SoC device tree source
> + *
> + * Copyright (c) 2018, The Linux Foundation. All rights reserved.
> + */
> +
> +&slim {
> + status = "okay";
> +
> + slim at 1 {
> + reg = <1>;
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + wcd9340_ifd: ifd at 0,0 {
> + compatible = "slim217,250";
> + reg = <0 0>;
> + };
> +
> + wcd9340: codec at 1,0 {
> + compatible = "slim217,250";
> + reg = <1 0>;
> + slim-ifc-dev = <&wcd9340_ifd>;
> +
> + #sound-dai-cells = <1>;
> +
> + interrupts-extended = <&tlmm 54 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> + #interrupt-cells = <1>;
> +
> + clock-names = "extclk";
> + clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
> +
> + #clock-cells = <0>;
> + clock-frequency = <9600000>;
> + clock-output-names = "mclk";
> +
> + pinctrl-0 = <&wcd_intr_default>;
> + pinctrl-names = "default";
> +
> + qcom,micbias1-microvolt = <1800000>;
> + qcom,micbias2-microvolt = <1800000>;
> + qcom,micbias3-microvolt = <1800000>;
> + qcom,micbias4-microvolt = <1800000>;
> +
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + wcdgpio: gpio-controller at 42 {
> + compatible = "qcom,wcd9340-gpio";
> + gpio-controller;
> + #gpio-cells = <2>;
> + reg = <0x42 0x2>;
> + };
> +
> + swm: swm at c85 {
> + compatible = "qcom,soundwire-v1.3.0";
> + reg = <0xc85 0x40>;
> + interrupts-extended = <&wcd9340 20>;
> +
> + qcom,dout-ports = <6>;
> + qcom,din-ports = <2>;
> + qcom,ports-sinterval-low = /bits/ 8 <0x07 0x1f 0x3f 0x7 0x1f 0x3f 0x0f 0x0f>;
> + qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0c 0x6 0x12 0x0d 0x07 0x0a>;
> + qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x1f 0x00 0x00 0x1f 0x00 0x00>;
> +
> + #sound-dai-cells = <1>;
> + clocks = <&wcd9340>;
> + clock-names = "iface";
> + #address-cells = <2>;
> + #size-cells = <0>;
> + };
> + };
> + };
> +};
> +
> +&tlmm {
> + wcd_intr_default: wcd-intr-default-state {
> + pins = "gpio54";
> + function = "gpio";
> +
> + bias-pull-down;
> + drive-strength = <2>;
> + };
> +};
>
> --
> 2.43.1
>
More information about the U-Boot
mailing list