[PATCH v4 10/39] gpio: qcom_pmic: add a quirk to skip GPIO configuration

Sumit Garg sumit.garg at linaro.org
Wed Feb 21 10:36:43 CET 2024


On Wed, 21 Feb 2024 at 14:19, Neil Armstrong <neil.armstrong at linaro.org> wrote:
>
> On 20/02/2024 06:56, Sumit Garg wrote:
> > On Fri, 16 Feb 2024 at 02:22, Caleb Connolly <caleb.connolly at linaro.org> wrote:
> >>
> >> Some platforms hard reset when attempting to configure PMIC GPIOs. Add
> >> support for quirks specified in match data with a single quirk to skip
> >> this configuration. We rely on the GPIO already be configured correctly,
> >> which is always the case for volume up (the only current user of these
> >> GPIOs).
> >
> > I can't find a similar quirk in the counterpart Linux driver
> > (drivers/pinctrl/qcom/pinctrl-spmi-gpio.c). Is there anything we are
> > missing in the U-Boot driver?
>
> It's not ideal, it's fine to have it at first but at some point a proper
> solution should be found.

Then at least let's add code comments to say that it is just a
workaround for the time being until a proper solution is found.

-Sumit

>
> Neil
>
> >
> > -Sumit
> >
> >>
> >> Signed-off-by: Caleb Connolly <caleb.connolly at linaro.org>
> >> ---
> >>   drivers/gpio/qcom_pmic_gpio.c | 18 ++++++++++++++++--
> >>   1 file changed, 16 insertions(+), 2 deletions(-)
> >>
> >> diff --git a/drivers/gpio/qcom_pmic_gpio.c b/drivers/gpio/qcom_pmic_gpio.c
> >> index 2a4fef8d28cb..198cd84bc31e 100644
> >> --- a/drivers/gpio/qcom_pmic_gpio.c
> >> +++ b/drivers/gpio/qcom_pmic_gpio.c
> >> @@ -64,6 +64,15 @@
> >>   #define REG_EN_CTL             0x46
> >>   #define REG_EN_CTL_ENABLE      (1 << 7)
> >>
> >> +/**
> >> + * pmic_gpio_match_data - platform specific configuration
> >> + *
> >> + * @PMIC_MATCH_READONLY: treat all GPIOs as readonly, don't attempt to configure them
> >> + */
> >> +enum pmic_gpio_quirks {
> >> +       QCOM_PMIC_QUIRK_READONLY = (1 << 0),
> >> +};
> >> +
> >>   struct qcom_gpio_bank {
> >>          uint32_t pid; /* Peripheral ID on SPMI bus */
> >>          bool     lv_mv_type; /* If subtype is GPIO_LV(0x10) or GPIO_MV(0x11) */
> >> @@ -75,7 +84,12 @@ static int qcom_gpio_set_direction(struct udevice *dev, unsigned offset,
> >>          struct qcom_gpio_bank *priv = dev_get_priv(dev);
> >>          uint32_t gpio_base = priv->pid + REG_OFFSET(offset);
> >>          uint32_t reg_ctl_val;
> >> -       int ret;
> >> +       ulong quirks = dev_get_driver_data(dev);
> >> +       int ret = 0;
> >> +
> >> +       /* Some PMICs don't like their GPIOs being configured */
> >> +       if (quirks & QCOM_PMIC_QUIRK_READONLY)
> >> +               return 0;
> >>
> >>          /* Disable the GPIO */
> >>          ret = pmic_clrsetbits(dev->parent, gpio_base + REG_EN_CTL,
> >> @@ -304,7 +318,7 @@ static int qcom_gpio_of_to_plat(struct udevice *dev)
> >>   static const struct udevice_id qcom_gpio_ids[] = {
> >>          { .compatible = "qcom,pm8916-gpio" },
> >>          { .compatible = "qcom,pm8994-gpio" },   /* 22 GPIO's */
> >> -       { .compatible = "qcom,pm8998-gpio" },
> >> +       { .compatible = "qcom,pm8998-gpio", .data = QCOM_PMIC_QUIRK_READONLY },
> >>          { .compatible = "qcom,pms405-gpio" },
> >>          { }
> >>   };
> >>
> >> --
> >> 2.43.1
> >>


More information about the U-Boot mailing list