[PATCH v2] rockchip: rk3328: Set efuse auto mode and timing control

[Jonas Karlman]

Reading from efuse return zero when mainline TF-A is used.

  => dump_efuse
  00000000: 00 00 00 00  ....
  00000004: 00 00 00 00  ....
  00000008: 00 00 00 00  ....
  0000000c: 00 00 00 00  ....
  00000010: 00 00 00 00  ....
  00000014: 00 00 00 00  ....
  00000018: 00 00 00 00  ....
  0000001c: 00 00 00 00  ....

However, when vendor TF-A blobs is used reading from efuse works.

Change to use auto mode, enable finish and auto access err interrupts
and set timing control using same values that vendor TF-A blob use to
fix this.

With this efuse can be read when either of mainline TF-A or vendor blob
is used.

  => dump_efuse
  00000000: 52 4b 33 82  RK3.
  00000004: 00 fe 21 55  ..!U
  00000008: 52 4b 57 34  RKW4
  0000000c: 35 30 32 39  5029
  00000010: 00 00 00 00  ....
  00000014: 08 25 0c 0f  .%..
  00000018: 02 0d 08 00  ....
  0000001c: 00 00 f0 00  ....

Signed-off-by: Jonas Karlman <jonas at kwiboo.se>
---
Changes in v2:
- Read and mask user mode flag instead of force 0x46 value

 arch/arm/mach-rockchip/rk3328/rk3328.c | 38 ++++++++++++++++++++++++++
 1 file changed, 38 insertions(+)

diff --git a/arch/arm/mach-rockchip/rk3328/rk3328.c b/arch/arm/mach-rockchip/rk3328/rk3328.c
index de17b8868273..ca623c0d3d03 100644
--- a/arch/arm/mach-rockchip/rk3328/rk3328.c
+++ b/arch/arm/mach-rockchip/rk3328/rk3328.c
@@ -19,6 +19,23 @@ DECLARE_GLOBAL_DATA_PTR;
 #define GRF_BASE		0xFF100000
 #define UART2_BASE		0xFF130000
 #define FW_DDR_CON_REG		0xFF7C0040
+#define EFUSE_NS_BASE		0xFF260000
+
+#define EFUSE_MOD		0x0000
+#define EFUSE_INT_CON		0x0014
+#define EFUSE_T_CSB_P		0x0028
+#define EFUSE_T_PGENB_P		0x002C
+#define EFUSE_T_LOAD_P		0x0030
+#define EFUSE_T_ADDR_P		0x0034
+#define EFUSE_T_STROBE_P	0x0038
+#define EFUSE_T_CSB_R		0x003C
+#define EFUSE_T_PGENB_R		0x0040
+#define EFUSE_T_LOAD_R		0x0044
+#define EFUSE_T_ADDR_R		0x0048
+#define EFUSE_T_STROBE_R	0x004C
+
+#define EFUSE_USER_MODE		0x1
+#define EFUSE_TIMING(s, l)	(((s) << 16) | (l))
 
 const char * const boot_devices[BROM_LAST_BOOTSOURCE + 1] = {
 	[BROM_BOOTSOURCE_EMMC] = "/mmc at ff520000",
@@ -50,10 +67,31 @@ struct mm_region *mem_map = rk3328_mem_map;
 int arch_cpu_init(void)
 {
 #ifdef CONFIG_SPL_BUILD
+	u32 reg;
+
 	/* We do some SoC one time setting here. */
 
 	/* Disable the ddr secure region setting to make it non-secure */
 	rk_setreg(FW_DDR_CON_REG, 0x200);
+
+	/* Use efuse auto mode */
+	reg = readl(EFUSE_NS_BASE + EFUSE_MOD);
+	writel(reg & ~EFUSE_USER_MODE, EFUSE_NS_BASE + EFUSE_MOD);
+
+	/* Enable efuse finish and auto access err interrupt */
+	writel(0x07, EFUSE_NS_BASE + EFUSE_INT_CON);
+
+	/* Set efuse timing control */
+	writel(EFUSE_TIMING(1, 241), EFUSE_NS_BASE + EFUSE_T_CSB_P);
+	writel(EFUSE_TIMING(1, 241), EFUSE_NS_BASE + EFUSE_T_PGENB_P);
+	writel(EFUSE_TIMING(1, 241), EFUSE_NS_BASE + EFUSE_T_LOAD_P);
+	writel(EFUSE_TIMING(1, 241), EFUSE_NS_BASE + EFUSE_T_ADDR_P);
+	writel(EFUSE_TIMING(2, 240), EFUSE_NS_BASE + EFUSE_T_STROBE_P);
+	writel(EFUSE_TIMING(1, 4), EFUSE_NS_BASE + EFUSE_T_CSB_R);
+	writel(EFUSE_TIMING(1, 4), EFUSE_NS_BASE + EFUSE_T_PGENB_R);
+	writel(EFUSE_TIMING(1, 4), EFUSE_NS_BASE + EFUSE_T_LOAD_R);
+	writel(EFUSE_TIMING(1, 4), EFUSE_NS_BASE + EFUSE_T_ADDR_R);
+	writel(EFUSE_TIMING(2, 3), EFUSE_NS_BASE + EFUSE_T_STROBE_R);
 #endif
 	return 0;
 }
-- 
2.43.0