[PATCH v2 00/32] Qualcomm generic board support
Sumit Garg
sumit.garg at linaro.org
Tue Jan 9 07:07:55 CET 2024
On Fri, 5 Jan 2024 at 19:15, Caleb Connolly <caleb.connolly at linaro.org> wrote:
>
>
>
> On 05/01/2024 13:14, Sumit Garg wrote:
> > Hi Caleb,
>
> Hi Sumit,
>
> [snip]
>
> >> ---
> >> I have tested this series on the Dragonboard410c, Dragonboard820c, and
> >
> > This series fails to boot (without any U-Boot console print) on
> > db410c. I even added below pinctrl change but without any success:
>
> Are you chainloading from aboot? Or flashing over it?
>
I am using the default mode where U-Boot acts as the first stage
bootloader. I suppose it worked for you since LK enabled drivers which
were just reused by U-Boot.
> I have only been able to validate the chainloading method, following the
> steps in doc/board/qualcomm/board.rst and generating the config with
>
> make dragonboard410c_defconfig chainloaded.config
>
> do you get any output at all?
No output from U-Boot. Last prints from SBL1:
<snip>
D - 299022 - SBL1, Delta
S - Flash Throughput, 81000 KB/s (1537656 Bytes, 18940 us)
S - DDR Frequency, 400 MHz
> Can you try enabling debug UART output as
> documented in doc/board/qualcomm/debugging.rst?
I did but it didn't help.
>
> The pinctrl fix shouldn't be needed to boot to a shell.
While at it, I noticed another pinctrl issue which should be fixed by
following diff:
diff --git a/drivers/serial/serial_msm.c b/drivers/serial/serial_msm.c
index 0148ddb54df..6fe7bdd1dca 100644
--- a/drivers/serial/serial_msm.c
+++ b/drivers/serial/serial_msm.c
@@ -204,7 +204,7 @@ static int msm_serial_probe(struct udevice *dev)
if (ret)
return ret;
- pinctrl_select_state(dev, "uart");
+ pinctrl_select_state(dev, "default");
uart_dm_init(priv);
return 0;
But this still didn't fix the boot problem. As you have the board in
your hand, I would suggest you to debug to avoid this back and forth.
-Sumit
>
> Thanks,
> >
> > diff --git a/drivers/pinctrl/qcom/pinctrl-apq8016.c
> > b/drivers/pinctrl/qcom/pinctrl-apq8016.c
> > index 8e698085d78..88518845952 100644
> > --- a/drivers/pinctrl/qcom/pinctrl-apq8016.c
> > +++ b/drivers/pinctrl/qcom/pinctrl-apq8016.c
> > @@ -42,7 +42,7 @@ static const char *apq8016_get_pin_name(struct udevice *dev,
> > unsigned int selector)
> > {
> > if (selector < 122) {
> > - snprintf(pin_name, MAX_PIN_NAME_LEN, "GPIO_%u", selector);
> > + snprintf(pin_name, MAX_PIN_NAME_LEN, "gpio%u", selector);
> > return pin_name;
> > } else {
> > return msm_pinctrl_pins[selector - 122];
> >
> >
> >> Dragonboard845c. I unfortunately don't have access to a QCS404 EVB board
> >> to test.
> >
> > db820c and qcs404 require a similar pinctrl change though.
> >
> > -Sumit
> >
> >>
> >> This series is based on the qcom-next branch [1] and depends on my PMIC
> >> fixes series [2], an integration branch for testing can be found at [3].
> >> The non-qualcomm-specific changes (patches 1 and 2) don't have any
> >> dependencies.
> >>
> >> [1]: https://source.denx.de/u-boot/custodians/u-boot-snapdragon
> >> [2]: https://lore.kernel.org/u-boot/20231114-b4-qcom-dt-compat-v3-0-88a92f8f00ba@linaro.org/
> >> [3]: https://source.denx.de/u-boot/custodians/u-boot-snapdragon/-/tree/b4/qcom-common-target
> >>
> >> ---
> >> Changes in v2:
> >> - Split DTS changes to reduce patch size.
> >> - Import full board DTS files from Linux too, and introduce -u-boot.dtsi
> >> files where necessary to make any U-Boot specific changes.
> >> - Add a pinctrl driver for qcom PMIC GPIOs
> >> - Always enable LINUX_KERNEL_IMAGE_HEADER
> >> - Link to v1: https://lore.kernel.org/r/20231121-b4-qcom-common-target-v1-0-9492198e0c15@linaro.org
> >>
> >> To: Neil Armstrong <neil.armstrong at linaro.org>
> >> To: Sumit Garg <sumit.garg at linaro.org>
> >> To: Ramon Fried <rfried.dev at gmail.com>
> >> Cc: Marek Vasut <marex at denx.de>
> >> To: Dzmitry Sankouski <dsankouski at gmail.com>
> >> To: Caleb Connolly <caleb.connolly at linaro.org>
> >> To: Peng Fan <peng.fan at nxp.com>
> >> To: Jaehoon Chung <jh80.chung at samsung.com>
> >> To: Rayagonda Kokatanur <rayagonda.kokatanur at broadcom.com>
> >> To: Lukasz Majewski <lukma at denx.de>
> >> To: Sean Anderson <seanga2 at gmail.com>
> >> To: Jorge Ramirez-Ortiz <jorge.ramirez.ortiz at gmail.com>
> >> To: Stephan Gerhold <stephan at gerhold.net>
> >> Cc: <u-boot at lists.denx.de>
> >>
> >> ---
> >> Caleb Connolly (32):
> >> arm: init: export prev_bl_fdt_addr
> >> usb: dwc3-generic: support external vbus regulator
> >> mmc: msm_sdhci: use modern clock handling
> >> dt-bindings: drop msm_sdhci binding
> >> clk/qcom: use upstream compatible properties
> >> serial: msm: add debug UART
> >> serial: msm: fix clock handling
> >> gpio: qcom_pmic: 1-based GPIOs
> >> gpio: qcom_pmic: add a quirk to skip GPIO configuration
> >> gpio: qcom_pmic: add pinctrl driver
> >> board: dragonboard410c: add chainloaded config fragment
> >> board: dragonboard410c: upstream DT compat
> >> board: dragonboard410c: import board code from mach-snapdragon
> >> board: dragonboard820c: use LINUX_KERNEL_IMAGE_HEADER
> >> mach-snapdragon: generalise board support
> >> mach-snapdragon: dynamic load addresses
> >> mach-snapdragon: generate fdtfile automatically
> >> doc: board/qualcomm: document generic targets
> >> dt-bindings: import headers for SDM845
> >> dts: sdm845: import supporting dtsi files
> >> dts: sdm845: replace with upstream DTS
> >> dt-bindings: import headers for MSM8916
> >> dts: msm8916: import PMIC dtsi files
> >> dts: msm8916: replace with upstream DTS
> >> dt-bindings: import headers for MSM8996
> >> dts: msm8996: import PMIC dtsi files
> >> dts: dragonboard820c: use correct bindings for clocks
> >> dts: msm8996: replace with upstream DTS
> >> dt-bindings: import headers for qcs404
> >> dts: qcs404-evb: replace with upstream DT
> >> board: qcs404-evb: drop board code
> >> MAINTAINERS: Qualcomm: add some missing paths
> >>
> >> MAINTAINERS | 12 +-
> >> arch/arm/Kconfig | 4 +
> >> arch/arm/dts/Makefile | 9 +-
> >> arch/arm/dts/apq8016-sbc.dts | 729 +++
> >> arch/arm/dts/apq8096-db820c-u-boot.dtsi | 10 +
> >> arch/arm/dts/apq8096-db820c.dts | 1137 ++++
> >> arch/arm/dts/dragonboard410c-uboot.dtsi | 44 -
> >> arch/arm/dts/dragonboard410c.dts | 199 +-
> >> arch/arm/dts/dragonboard820c-uboot.dtsi | 32 -
> >> arch/arm/dts/dragonboard820c.dts | 151 -
> >> arch/arm/dts/dragonboard845c-uboot.dtsi | 26 -
> >> arch/arm/dts/dragonboard845c.dts | 48 -
> >> arch/arm/dts/msm8916-pm8916.dtsi | 157 +
> >> arch/arm/dts/msm8916.dtsi | 2702 +++++++++
> >> arch/arm/dts/msm8996.dtsi | 3884 +++++++++++++
> >> arch/arm/dts/pm8916.dtsi | 178 +
> >> arch/arm/dts/pm8994.dtsi | 152 +
> >> arch/arm/dts/pm8998.dtsi | 130 +
> >> arch/arm/dts/pmi8994.dtsi | 65 +
> >> arch/arm/dts/pmi8998.dtsi | 98 +
> >> arch/arm/dts/pms405.dtsi | 149 +
> >> arch/arm/dts/qcs404-evb-4000-u-boot.dtsi | 26 +
> >> arch/arm/dts/qcs404-evb-4000.dts | 96 +
> >> arch/arm/dts/qcs404-evb-uboot.dtsi | 30 -
> >> arch/arm/dts/qcs404-evb.dts | 390 --
> >> arch/arm/dts/qcs404-evb.dtsi | 389 ++
> >> arch/arm/dts/qcs404.dtsi | 1829 ++++++
> >> arch/arm/dts/sdm845-db845c.dts | 1190 ++++
> >> .../arm/dts/sdm845-samsung-starqltechn-u-boot.dtsi | 16 +
> >> arch/arm/dts/sdm845-samsung-starqltechn.dts | 624 +++
> >> arch/arm/dts/sdm845-wcd9340.dtsi | 86 +
> >> arch/arm/dts/sdm845.dtsi | 5801 +++++++++++++++++++-
> >> arch/arm/dts/starqltechn-uboot.dtsi | 27 -
> >> arch/arm/dts/starqltechn.dts | 68 -
> >> arch/arm/lib/save_prev_bl_data.c | 5 +
> >> arch/arm/mach-snapdragon/Kconfig | 95 +-
> >> arch/arm/mach-snapdragon/Makefile | 8 +-
> >> arch/arm/mach-snapdragon/board.c | 304 +
> >> arch/arm/mach-snapdragon/include/mach/dram.h | 12 -
> >> arch/arm/mach-snapdragon/init_sdm845.c | 73 -
> >> arch/arm/mach-snapdragon/misc.c | 55 -
> >> arch/arm/mach-snapdragon/sysmap-apq8016.c | 31 -
> >> arch/arm/mach-snapdragon/sysmap-apq8096.c | 31 -
> >> arch/arm/mach-snapdragon/sysmap-qcs404.c | 43 -
> >> arch/arm/mach-snapdragon/sysmap-sdm845.c | 31 -
> >> board/qualcomm/dragonboard410c/Kconfig | 15 -
> >> board/qualcomm/dragonboard410c/Makefile | 3 +-
> >> .../dragonboard410c/configs/chainloaded.config | 7 +
> >> board/qualcomm/dragonboard410c/dragonboard410c.c | 109 +-
> >> .../qualcomm/dragonboard410c/misc.c | 51 +-
> >> .../mach => board/qualcomm/dragonboard410c}/misc.h | 1 +
> >> board/qualcomm/dragonboard820c/Kconfig | 15 -
> >> board/qualcomm/dragonboard820c/Makefile | 1 -
> >> board/qualcomm/dragonboard820c/dragonboard820c.c | 39 +-
> >> board/qualcomm/dragonboard820c/head.S | 33 -
> >> board/qualcomm/dragonboard820c/u-boot.lds | 111 -
> >> board/qualcomm/dragonboard845c/Kconfig | 12 -
> >> board/qualcomm/qcs404-evb/Kconfig | 15 -
> >> board/qualcomm/qcs404-evb/Makefile | 6 -
> >> board/qualcomm/qcs404-evb/qcs404-evb.c | 62 -
> >> configs/dragonboard410c_defconfig | 8 +-
> >> configs/dragonboard820c_defconfig | 8 +-
> >> configs/dragonboard845c_defconfig | 29 -
> >> configs/qcom_defconfig | 73 +
> >> configs/qcs404evb_defconfig | 55 -
> >> configs/starqltechn_defconfig | 41 -
> >> doc/board/qualcomm/board.rst | 119 +
> >> doc/board/qualcomm/debugging.rst | 61 +
> >> doc/board/qualcomm/index.rst | 4 +-
> >> doc/board/qualcomm/qcs404.rst | 79 -
> >> doc/board/qualcomm/sdm845.rst | 162 -
> >> doc/device-tree-bindings/mmc/msm_sdhci.txt | 25 -
> >> doc/device-tree-bindings/usb/ehci-msm.txt | 10 -
> >> drivers/clk/qcom/clock-apq8016.c | 9 +-
> >> drivers/clk/qcom/clock-apq8096.c | 7 +-
> >> drivers/gpio/qcom_pmic_gpio.c | 232 +-
> >> drivers/mmc/msm_sdhci.c | 69 +-
> >> drivers/phy/qcom/msm8916-usbh-phy.c | 4 +-
> >> drivers/pinctrl/qcom/pinctrl-apq8016.c | 2 +-
> >> drivers/serial/Kconfig | 8 +
> >> drivers/serial/serial_msm.c | 56 +-
> >> drivers/usb/dwc3/dwc3-generic.c | 12 +
> >> drivers/usb/host/ehci-msm.c | 24 +-
> >> include/configs/dragonboard845c.h | 20 -
> >> include/configs/qcom.h | 21 +
> >> include/configs/qcs404-evb.h | 20 -
> >> include/configs/sdm845.h | 26 -
> >> include/dt-bindings/arm/coresight-cti-dt.h | 37 +
> >> include/dt-bindings/clock/qcom,camcc-sdm845.h | 116 +
> >> include/dt-bindings/clock/qcom,dispcc-sdm845.h | 56 +
> >> include/dt-bindings/clock/qcom,gcc-msm8916.h | 179 +
> >> include/dt-bindings/clock/qcom,gcc-msm8996.h | 360 ++
> >> include/dt-bindings/clock/qcom,gpucc-sdm845.h | 24 +
> >> include/dt-bindings/clock/qcom,lpass-sdm845.h | 15 +
> >> include/dt-bindings/clock/qcom,mmcc-msm8996.h | 295 +
> >> include/dt-bindings/clock/qcom,rpmcc.h | 174 +
> >> include/dt-bindings/clock/qcom,rpmh.h | 37 +
> >> include/dt-bindings/clock/qcom,turingcc-qcs404.h | 15 +
> >> include/dt-bindings/clock/qcom,videocc-sdm845.h | 35 +
> >> include/dt-bindings/dma/qcom-gpi.h | 11 +
> >> include/dt-bindings/firmware/qcom,scm.h | 18 +
> >> include/dt-bindings/iio/qcom,spmi-vadc.h | 300 +
> >> include/dt-bindings/interconnect/qcom,msm8916.h | 100 +
> >> .../dt-bindings/interconnect/qcom,msm8996-cbf.h | 12 +
> >> include/dt-bindings/interconnect/qcom,msm8996.h | 163 +
> >> include/dt-bindings/interconnect/qcom,osm-l3.h | 15 +
> >> include/dt-bindings/interconnect/qcom,sdm845.h | 150 +
> >> include/dt-bindings/phy/phy-qcom-qmp.h | 20 +
> >> include/dt-bindings/phy/phy-qcom-qusb2.h | 37 +
> >> include/dt-bindings/pinctrl/qcom,pmic-gpio.h | 164 +
> >> include/dt-bindings/pinctrl/qcom,pmic-mpp.h | 106 +
> >> include/dt-bindings/power/qcom-rpmpd.h | 412 ++
> >> include/dt-bindings/qcom,q6asm.h | 26 +
> >> .../dt-bindings/regulator/qcom,rpmh-regulator.h | 36 +
> >> include/dt-bindings/reset/qcom,gcc-msm8916.h | 100 +
> >> include/dt-bindings/reset/qcom,sdm845-aoss.h | 17 +
> >> include/dt-bindings/reset/qcom,sdm845-pdc.h | 22 +
> >> include/dt-bindings/soc/qcom,apr.h | 28 +
> >> include/dt-bindings/soc/qcom,rpmh-rsc.h | 14 +
> >> include/dt-bindings/sound/apq8016-lpass.h | 9 +
> >> include/dt-bindings/sound/qcom,lpass.h | 46 +
> >> include/dt-bindings/sound/qcom,q6afe.h | 9 +
> >> include/dt-bindings/sound/qcom,q6asm.h | 26 +
> >> include/dt-bindings/sound/qcom,q6dsp-lpass-ports.h | 234 +
> >> include/dt-bindings/sound/qcom,wcd9335.h | 15 +
> >> include/init.h | 11 +
> >> 126 files changed, 23909 insertions(+), 2375 deletions(-)
> >> ---
> >> base-commit: bcb4a9ddbd21a61b5b421ba374a785757bd28c80
> >>
> >> // Caleb (they/them)
> >>
>
> --
> // Caleb (they/them)
More information about the U-Boot
mailing list