[PATCH v3 5/5] net: dwc_eth_qos: Add glue driver for Intel MAC

Philip Oberfichtner pro at denx.de
Wed Jul 17 14:29:06 CEST 2024


Add dwc_eth_qos glue driver for the Intel Elkhart-Lake SOC.

Signed-off-by: Philip Oberfichtner <pro at denx.de>
---

Notes:
    Changes in V3:
    - update linux reference to current stable
    - replace pr_err by dev_err
    - drop __prefix from local function names
    - use FIELD_PREP to simplify bitfield extraction

 drivers/net/Kconfig             |   7 +
 drivers/net/Makefile            |   1 +
 drivers/net/dwc_eth_qos.c       |  12 +
 drivers/net/dwc_eth_qos.h       |   1 +
 drivers/net/dwc_eth_qos_intel.c | 449 ++++++++++++++++++++++++++++++++
 drivers/net/dwc_eth_qos_intel.h |  57 ++++
 include/pci_ids.h               |   9 +
 7 files changed, 536 insertions(+)
 create mode 100644 drivers/net/dwc_eth_qos_intel.c
 create mode 100644 drivers/net/dwc_eth_qos_intel.h

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index b4ff033afa9..6f5618918f6 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -243,6 +243,13 @@ config DWC_ETH_QOS_IMX
 	  The Synopsys Designware Ethernet QOS IP block with the specific
 	  configuration used in IMX soc.
 
+config DWC_ETH_QOS_INTEL
+	bool "Synopsys DWC Ethernet QOS device support for Intel"
+	depends on DWC_ETH_QOS
+	help
+	  The Synopsys Designware Ethernet QOS IP block with the specific
+	  configuration used in the Intel Elkhart-Lake soc.
+
 config DWC_ETH_QOS_ROCKCHIP
 	bool "Synopsys DWC Ethernet QOS device support for Rockchip SoCs"
 	depends on DWC_ETH_QOS
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index dce71685c3d..685dda5a584 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -20,6 +20,7 @@ obj-$(CONFIG_DRIVER_DM9000) += dm9000x.o
 obj-$(CONFIG_DSA_SANDBOX) += dsa_sandbox.o
 obj-$(CONFIG_DWC_ETH_QOS) += dwc_eth_qos.o
 obj-$(CONFIG_DWC_ETH_QOS_IMX) += dwc_eth_qos_imx.o
+obj-$(CONFIG_DWC_ETH_QOS_INTEL) += dwc_eth_qos_intel.o
 obj-$(CONFIG_DWC_ETH_QOS_ROCKCHIP) += dwc_eth_qos_rockchip.o
 obj-$(CONFIG_DWC_ETH_QOS_QCOM) += dwc_eth_qos_qcom.o
 obj-$(CONFIG_DWC_ETH_XGMAC) += dwc_eth_xgmac.o
diff --git a/drivers/net/dwc_eth_qos.c b/drivers/net/dwc_eth_qos.c
index b7aef751866..19f0e9eb5b4 100644
--- a/drivers/net/dwc_eth_qos.c
+++ b/drivers/net/dwc_eth_qos.c
@@ -1408,6 +1408,18 @@ int eqos_get_base_addr_dt(struct udevice *dev)
 	return eqos_get_base_addr_common(dev, addr);
 }
 
+int eqos_get_base_addr_pci(struct udevice *dev)
+{
+	fdt_addr_t addr;
+	void *paddr;
+
+	paddr = dm_pci_map_bar(dev, PCI_BASE_ADDRESS_0, 0, 0, PCI_REGION_TYPE,
+							      PCI_REGION_MEM);
+	addr = paddr ? (fdt_addr_t)paddr : FDT_ADDR_T_NONE;
+
+	return eqos_get_base_addr_common(dev, addr);
+}
+
 static int eqos_probe(struct udevice *dev)
 {
 	struct eqos_priv *eqos = dev_get_priv(dev);
diff --git a/drivers/net/dwc_eth_qos.h b/drivers/net/dwc_eth_qos.h
index 1121d242ca6..0987bdd0b81 100644
--- a/drivers/net/dwc_eth_qos.h
+++ b/drivers/net/dwc_eth_qos.h
@@ -289,6 +289,7 @@ void eqos_flush_desc_generic(void *desc);
 void eqos_inval_buffer_generic(void *buf, size_t size);
 void eqos_flush_buffer_generic(void *buf, size_t size);
 int eqos_get_base_addr_dt(struct udevice *dev);
+int eqos_get_base_addr_pci(struct udevice *dev);
 int eqos_null_ops(struct udevice *dev);
 void *eqos_get_driver_data(struct udevice *dev);
 
diff --git a/drivers/net/dwc_eth_qos_intel.c b/drivers/net/dwc_eth_qos_intel.c
new file mode 100644
index 00000000000..a2c68257329
--- /dev/null
+++ b/drivers/net/dwc_eth_qos_intel.c
@@ -0,0 +1,449 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2023-2024 DENX Software Engineering GmbH
+ * Philip Oberfichtner <pro at denx.de>
+ *
+ * Based on linux v6.6.39, especially drivers/net/ethernet/stmicro/stmmac
+ */
+
+#include <asm/io.h>
+#include <dm.h>
+#include <dm/device_compat.h>
+#include <linux/bitfield.h>
+#include <linux/delay.h>
+#include <miiphy.h>
+#include <net.h>
+#include <pci.h>
+
+#include "dwc_eth_qos.h"
+#include "dwc_eth_qos_intel.h"
+
+static struct pci_device_id intel_pci_ids[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EHL_RGMII1G) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EHL_SGMII1) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EHL_SGMII2G5) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EHL_PSE0_RGMII1G) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EHL_PSE0_SGMII1G) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EHL_PSE0_SGMII2G5) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EHL_PSE1_RGMII1G) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EHL_PSE1_SGMII1G) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_EHL_PSE1_SGMII2G5) },
+	{}
+};
+
+static int pci_config(struct udevice *dev)
+{
+	u32 val;
+
+	/* Try to enable I/O accesses and bus-mastering */
+	dm_pci_read_config32(dev, PCI_COMMAND, &val);
+	val |= PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER;
+	dm_pci_write_config32(dev, PCI_COMMAND, val);
+
+	/* Make sure it worked */
+	dm_pci_read_config32(dev, PCI_COMMAND, &val);
+	if (!(val & PCI_COMMAND_MEMORY)) {
+		dev_err(dev, "%s: Can't enable I/O memory\n", __func__);
+		return -ENOSPC;
+	}
+
+	if (!(val & PCI_COMMAND_MASTER)) {
+		dev_err(dev, "%s: Can't enable bus-mastering\n", __func__);
+		return -EPERM;
+	}
+
+	return 0;
+}
+
+static void limit_fifo_size(struct udevice *dev)
+{
+	/*
+	 * As described in Intel Erratum EHL22, Document Number: 636674-2.1,
+	 * the PSE GbE Controllers advertise a wrong RX and TX fifo size.
+	 * Software should limit this value to 64KB.
+	 */
+	struct eqos_priv *eqos = dev_get_priv(dev);
+
+	eqos->tx_fifo_sz = 0x8000;
+	eqos->rx_fifo_sz = 0x8000;
+}
+
+static int serdes_status_poll(struct udevice *dev,
+			      unsigned char phyaddr, unsigned char phyreg,
+			      unsigned short mask, unsigned short val)
+{
+	struct eqos_priv *eqos = dev_get_priv(dev);
+	unsigned int retries = 10;
+	unsigned short val_rd;
+
+	do {
+		miiphy_read(eqos->mii->name, phyaddr, phyreg, &val_rd);
+		if ((val_rd & mask) == (val & mask))
+			return 0;
+		udelay(POLL_DELAY_US);
+	} while (--retries);
+
+	return -ETIMEDOUT;
+}
+
+ /* Returns -ve if MAC is unknown and 0 on success */
+static int mac_check_pse(const struct udevice *dev, bool *is_pse)
+{
+	struct pci_child_plat *plat = dev_get_parent_plat(dev);
+
+	if (!plat || plat->vendor != PCI_VENDOR_ID_INTEL)
+		return -ENXIO;
+
+	switch (plat->device) {
+	case PCI_DEVICE_ID_INTEL_EHL_PSE0_RGMII1G:
+	case PCI_DEVICE_ID_INTEL_EHL_PSE1_RGMII1G:
+	case PCI_DEVICE_ID_INTEL_EHL_PSE0_SGMII1G:
+	case PCI_DEVICE_ID_INTEL_EHL_PSE1_SGMII1G:
+	case PCI_DEVICE_ID_INTEL_EHL_PSE0_SGMII2G5:
+	case PCI_DEVICE_ID_INTEL_EHL_PSE1_SGMII2G5:
+		*is_pse = 1;
+		return 0;
+
+	case PCI_DEVICE_ID_INTEL_EHL_RGMII1G:
+	case PCI_DEVICE_ID_INTEL_EHL_SGMII1:
+	case PCI_DEVICE_ID_INTEL_EHL_SGMII2G5:
+		*is_pse = 0;
+		return 0;
+	};
+
+	return -ENXIO;
+}
+
+/* Check if we're in 2G5 mode */
+static bool serdes_link_mode_2500(struct udevice *dev)
+{
+	const unsigned char phyad = INTEL_MGBE_ADHOC_ADDR;
+	struct eqos_priv *eqos = dev_get_priv(dev);
+	unsigned short data;
+
+	miiphy_read(eqos->mii->name, phyad, SERDES_GCR, &data);
+	if (FIELD_GET(SERDES_LINK_MODE_MASK, data) == SERDES_LINK_MODE_2G5)
+		return true;
+
+	return false;
+}
+
+static int serdes_powerup(struct udevice *dev)
+{
+	/* Based on linux/drivers/net/ethernet/stmicro/stmmac/dwmac-intel.c */
+
+	const unsigned char phyad = INTEL_MGBE_ADHOC_ADDR;
+	struct eqos_priv *eqos = dev_get_priv(dev);
+	unsigned short data;
+	int ret;
+	bool is_pse;
+
+	/* Set the serdes rate and the PCLK rate */
+	miiphy_read(eqos->mii->name, phyad, SERDES_GCR0, &data);
+
+	data &= ~SERDES_RATE_MASK;
+	data &= ~SERDES_PCLK_MASK;
+
+	if (serdes_link_mode_2500(dev))
+		data |= SERDES_RATE_PCIE_GEN2 << SERDES_RATE_PCIE_SHIFT |
+			SERDES_PCLK_37p5MHZ << SERDES_PCLK_SHIFT;
+	else
+		data |= SERDES_RATE_PCIE_GEN1 << SERDES_RATE_PCIE_SHIFT |
+			SERDES_PCLK_70MHZ << SERDES_PCLK_SHIFT;
+
+	miiphy_write(eqos->mii->name, phyad, SERDES_GCR0, data);
+
+	/* assert clk_req */
+	miiphy_read(eqos->mii->name, phyad, SERDES_GCR0, &data);
+	data |= SERDES_PLL_CLK;
+	miiphy_write(eqos->mii->name, phyad, SERDES_GCR0, data);
+
+	/* check for clk_ack assertion */
+	ret = serdes_status_poll(dev, phyad, SERDES_GSR0,
+				 SERDES_PLL_CLK, SERDES_PLL_CLK);
+
+	if (ret) {
+		dev_err(dev, "Serdes PLL clk request timeout\n");
+		return ret;
+	}
+
+	/* assert lane reset*/
+	miiphy_read(eqos->mii->name, phyad, SERDES_GCR0, &data);
+	data |= SERDES_RST;
+	miiphy_write(eqos->mii->name, phyad, SERDES_GCR0, data);
+
+	/* check for assert lane reset reflection */
+	ret = serdes_status_poll(dev, phyad, SERDES_GSR0,
+				 SERDES_RST, SERDES_RST);
+
+	if (ret) {
+		dev_err(dev, "Serdes assert lane reset timeout\n");
+		return ret;
+	}
+
+	/* move power state to P0 */
+	miiphy_read(eqos->mii->name, phyad, SERDES_GCR0, &data);
+	data &= ~SERDES_PWR_ST_MASK;
+	data |= SERDES_PWR_ST_P0 << SERDES_PWR_ST_SHIFT;
+	miiphy_write(eqos->mii->name, phyad, SERDES_GCR0, data);
+
+	/* Check for P0 state */
+	ret = serdes_status_poll(dev, phyad, SERDES_GSR0,
+				 SERDES_PWR_ST_MASK,
+				 SERDES_PWR_ST_P0 << SERDES_PWR_ST_SHIFT);
+
+	if (ret) {
+		dev_err(dev, "Serdes power state P0 timeout.\n");
+		return ret;
+	}
+
+	/* PSE only - ungate SGMII PHY Rx Clock*/
+	ret = mac_check_pse(dev, &is_pse);
+	if (ret) {
+		dev_err(dev, "Failed to determine MAC type.\n");
+		return ret;
+	}
+
+	if (is_pse) {
+		miiphy_read(eqos->mii->name, phyad, SERDES_GCR0, &data);
+		data |= SERDES_PHY_RX_CLK;
+		miiphy_write(eqos->mii->name, phyad, SERDES_GCR0, data);
+	}
+
+	return 0;
+}
+
+static int xpcs_access(struct udevice *dev, int reg, int v)
+{
+	/*
+	 * Common read/write helper function
+	 *
+	 * It may seem a bit odd at a first glance that we use bus->read()
+	 * directly insetad of one of the wrapper functions. But:
+	 *
+	 * (1) phy_read() can't be used because we do not access an acutal PHY,
+	 *     but a MAC-internal submodule.
+	 *
+	 * (2) miiphy_read() can't be used because it assumes MDIO_DEVAD_NONE.
+	 */
+
+	int port = INTEL_MGBE_XPCS_ADDR;
+	int devad = 0x1f;
+	u16 val;
+	struct eqos_priv *eqos;
+	struct mii_dev *bus;
+
+	eqos = dev_get_priv(dev);
+	bus = eqos->mii;
+
+	if (v < 0)
+		return bus->read(bus, port, devad, reg);
+
+	val = v;
+	return bus->write(bus, port, devad, reg, val);
+}
+
+static int xpcs_read(struct udevice *dev, int reg)
+{
+	return xpcs_access(dev, reg, -1);
+}
+
+static int xpcs_write(struct udevice *dev, int reg, u16 val)
+{
+	return xpcs_access(dev, reg, val);
+}
+
+static int xpcs_clr_bits(struct udevice *dev, int reg, u16 bits)
+{
+	int ret;
+
+	ret = xpcs_read(dev, reg);
+	if (ret < 0)
+		return ret;
+
+	ret &= ~bits;
+
+	return xpcs_write(dev, reg, ret);
+}
+
+static int xpcs_set_bits(struct udevice *dev, int reg, u16 bits)
+{
+	int ret;
+
+	ret = xpcs_read(dev, reg);
+	if (ret < 0)
+		return ret;
+
+	ret |= bits;
+
+	return xpcs_write(dev, reg, ret);
+}
+
+static int xpcs_init(struct udevice *dev)
+{
+	/* Based on linux/drivers/net/pcs/pcs-xpcs.c */
+	struct eqos_priv *eqos = dev_get_priv(dev);
+	phy_interface_t interface = eqos->config->interface(dev);
+
+	if (interface != PHY_INTERFACE_MODE_SGMII)
+		return 0;
+
+	if (xpcs_clr_bits(dev, VR_MII_MMD_CTRL,  XPCS_AN_CL37_EN)  ||
+	    xpcs_set_bits(dev, VR_MII_AN_CTRL,   XPCS_MODE_SGMII)  ||
+	    xpcs_set_bits(dev, VR_MII_DIG_CTRL1, XPCS_MAC_AUTO_SW) ||
+	    xpcs_set_bits(dev, VR_MII_MMD_CTRL,  XPCS_AN_CL37_EN))
+		return -EIO;
+
+	return 0;
+}
+
+static int eqos_probe_ressources_intel(struct udevice *dev)
+{
+	int ret;
+
+	ret = eqos_get_base_addr_pci(dev);
+	if (ret) {
+		dev_err(dev, "eqos_get_base_addr_pci failed: %d\n", ret);
+		return ret;
+	}
+
+	limit_fifo_size(dev);
+
+	ret = pci_config(dev);
+	if (ret) {
+		dev_err(dev, "pci_config failed: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+struct eqos_config eqos_intel_config;
+
+/*
+ * overwrite __weak function from eqos_intel.c
+ *
+ * For PCI devices the devcie tree is optional. Choose driver data based on PCI
+ * IDs instead.
+ */
+void *eqos_get_driver_data(struct udevice *dev)
+{
+	const struct pci_device_id *id;
+	const struct pci_child_plat *plat;
+
+	plat = dev_get_parent_plat(dev);
+
+	if (!plat)
+		return NULL;
+
+	/* last intel_pci_ids element is zero initialized */
+	for (id = intel_pci_ids; id->vendor != 0; id++) {
+		if (id->vendor == plat->vendor && id->device == plat->device)
+			return &eqos_intel_config;
+	}
+
+	return NULL;
+}
+
+static int eqos_start_resets_intel(struct udevice *dev)
+{
+	int ret;
+
+	ret = xpcs_init(dev);
+	if (ret) {
+		dev_err(dev, "xpcs init failed.\n");
+		return ret;
+	}
+
+	ret = serdes_powerup(dev);
+	if (ret) {
+		dev_err(dev, "Failed to power up serdes.\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static ulong eqos_get_tick_clk_rate_intel(struct udevice *dev)
+{
+	return 0;
+}
+
+static int eqos_get_enetaddr_intel(struct udevice *dev)
+{
+	/* Assume MAC address is programmed by previous boot stage */
+	struct eth_pdata *plat = dev_get_plat(dev);
+	struct eqos_priv *eqos = dev_get_priv(dev);
+	u8 *lo = (u8 *)&eqos->mac_regs->address0_low;
+	u8 *hi = (u8 *)&eqos->mac_regs->address0_high;
+
+	plat->enetaddr[0] = lo[0];
+	plat->enetaddr[1] = lo[1];
+	plat->enetaddr[2] = lo[2];
+	plat->enetaddr[3] = lo[3];
+	plat->enetaddr[4] = hi[0];
+	plat->enetaddr[5] = hi[1];
+
+	return 0;
+}
+
+static phy_interface_t eqos_get_interface_intel(const struct udevice *dev)
+{
+	struct pci_child_plat *plat = dev_get_parent_plat(dev);
+
+	if (!plat || plat->vendor != PCI_VENDOR_ID_INTEL)
+		return PHY_INTERFACE_MODE_NA;
+
+	switch (plat->device) {
+	/* The GbE Host Controller has no RGMII interface */
+	case PCI_DEVICE_ID_INTEL_EHL_RGMII1G:
+		return PHY_INTERFACE_MODE_NA;
+
+	case PCI_DEVICE_ID_INTEL_EHL_PSE0_RGMII1G:
+	case PCI_DEVICE_ID_INTEL_EHL_PSE1_RGMII1G:
+		return PHY_INTERFACE_MODE_RGMII;
+
+	/* Host SGMII and Host SGMII2G5 share the same device id */
+	case PCI_DEVICE_ID_INTEL_EHL_SGMII1:
+	case PCI_DEVICE_ID_INTEL_EHL_SGMII2G5:
+	case PCI_DEVICE_ID_INTEL_EHL_PSE0_SGMII2G5:
+	case PCI_DEVICE_ID_INTEL_EHL_PSE0_SGMII1G:
+	case PCI_DEVICE_ID_INTEL_EHL_PSE1_SGMII1G:
+	case PCI_DEVICE_ID_INTEL_EHL_PSE1_SGMII2G5:
+		return PHY_INTERFACE_MODE_SGMII;
+	};
+
+	return PHY_INTERFACE_MODE_NA;
+}
+
+static struct eqos_ops eqos_intel_ops = {
+	.eqos_inval_desc = eqos_inval_desc_generic,
+	.eqos_flush_desc = eqos_flush_desc_generic,
+	.eqos_inval_buffer = eqos_inval_buffer_generic,
+	.eqos_flush_buffer = eqos_flush_buffer_generic,
+	.eqos_probe_resources =  eqos_probe_ressources_intel,
+	.eqos_remove_resources = eqos_null_ops,
+	.eqos_stop_resets = eqos_null_ops,
+	.eqos_start_resets = eqos_start_resets_intel,
+	.eqos_stop_clks = eqos_null_ops,
+	.eqos_start_clks = eqos_null_ops,
+	.eqos_calibrate_pads = eqos_null_ops,
+	.eqos_disable_calibration = eqos_null_ops,
+	.eqos_set_tx_clk_speed = eqos_null_ops,
+	.eqos_get_enetaddr = eqos_get_enetaddr_intel,
+	.eqos_get_tick_clk_rate = eqos_get_tick_clk_rate_intel,
+};
+
+struct eqos_config eqos_intel_config = {
+	.reg_access_always_ok = false,
+	.mdio_wait = 10,
+	.swr_wait = 50,
+	.config_mac = EQOS_MAC_RXQ_CTRL0_RXQ0EN_ENABLED_DCB,
+	.config_mac_mdio = EQOS_MAC_MDIO_ADDRESS_CR_250_300,
+	.axi_bus_width = EQOS_AXI_WIDTH_64,
+	.interface = eqos_get_interface_intel,
+	.ops = &eqos_intel_ops
+};
+
+extern U_BOOT_DRIVER(eth_eqos);
+U_BOOT_PCI_DEVICE(eth_eqos, intel_pci_ids);
diff --git a/drivers/net/dwc_eth_qos_intel.h b/drivers/net/dwc_eth_qos_intel.h
new file mode 100644
index 00000000000..847c75ede54
--- /dev/null
+++ b/drivers/net/dwc_eth_qos_intel.h
@@ -0,0 +1,57 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * Copyright (c) 2023-2024 DENX Software Engineering GmbH
+ * Philip Oberfichtner <pro at denx.de>
+ *
+ * This header is based on linux v6.6.39,
+ *
+ *	drivers/net/pcs/pcs-xpcs.h
+ *	drivers/net/ethernet/stmicro/stmmac/dwmac-intel.h,
+ *
+ *      Copyright (c) 2020 Synopsys, Inc. and/or its affiliates
+ *      Copyright (c) 2020 Intel Corporation
+ */
+
+#ifndef __DWMAC_INTEL_H__
+#define __DWMAC_INTEL_H__
+
+#define POLL_DELAY_US 8
+
+/* SERDES Register */
+#define SERDES_GCR	0x0	/* Global Conguration */
+#define SERDES_GSR0	0x5	/* Global Status Reg0 */
+#define SERDES_GCR0	0xb	/* Global Configuration Reg0 */
+
+/* SERDES defines */
+#define SERDES_PLL_CLK		BIT(0)		/* PLL clk valid signal */
+#define SERDES_PHY_RX_CLK	BIT(1)		/* PSE SGMII PHY rx clk */
+#define SERDES_RST		BIT(2)		/* Serdes Reset */
+#define SERDES_PWR_ST_MASK	GENMASK(6, 4)	/* Serdes Power state*/
+#define SERDES_RATE_MASK	GENMASK(9, 8)
+#define SERDES_PCLK_MASK	GENMASK(14, 12)	/* PCLK rate to PHY */
+#define SERDES_LINK_MODE_MASK	GENMASK(2, 1)
+#define SERDES_PWR_ST_SHIFT	4
+#define SERDES_PWR_ST_P0	0x0
+#define SERDES_PWR_ST_P3	0x3
+#define SERDES_LINK_MODE_2G5	0x3
+#define SERSED_LINK_MODE_1G	0x2
+#define SERDES_PCLK_37p5MHZ	0x0
+#define SERDES_PCLK_70MHZ	0x1
+#define SERDES_RATE_PCIE_GEN1	0x0
+#define SERDES_RATE_PCIE_GEN2	0x1
+#define SERDES_RATE_PCIE_SHIFT	8
+#define SERDES_PCLK_SHIFT	12
+
+#define INTEL_MGBE_ADHOC_ADDR	0x15
+#define INTEL_MGBE_XPCS_ADDR	0x16
+
+/* XPCS defines */
+#define XPCS_MODE_SGMII		BIT(2)
+#define XPCS_MAC_AUTO_SW	BIT(9)
+#define XPCS_AN_CL37_EN		BIT(12)
+
+#define VR_MII_MMD_CTRL		0x0000
+#define VR_MII_DIG_CTRL1	0x8000
+#define VR_MII_AN_CTRL		0x8001
+
+#endif /* __DWMAC_INTEL_H__ */
diff --git a/include/pci_ids.h b/include/pci_ids.h
index 6f095442cac..a6f99cb5987 100644
--- a/include/pci_ids.h
+++ b/include/pci_ids.h
@@ -2601,6 +2601,15 @@
 #define PCI_DEVICE_ID_DCI_PCCOM2	0x0004
 
 #define PCI_VENDOR_ID_INTEL		0x8086
+#define PCI_DEVICE_ID_INTEL_EHL_RGMII1G       0x4b30
+#define PCI_DEVICE_ID_INTEL_EHL_SGMII1        0x4b31
+#define PCI_DEVICE_ID_INTEL_EHL_SGMII2G5      0x4b32
+#define PCI_DEVICE_ID_INTEL_EHL_PSE0_RGMII1G  0x4ba0
+#define PCI_DEVICE_ID_INTEL_EHL_PSE0_SGMII1G  0x4ba1
+#define PCI_DEVICE_ID_INTEL_EHL_PSE0_SGMII2G5 0x4ba2
+#define PCI_DEVICE_ID_INTEL_EHL_PSE1_RGMII1G  0x4bb0
+#define PCI_DEVICE_ID_INTEL_EHL_PSE1_SGMII1G  0x4bb1
+#define PCI_DEVICE_ID_INTEL_EHL_PSE1_SGMII2G5 0x4bb2
 #define PCI_DEVICE_ID_INTEL_EESSC	0x0008
 #define PCI_DEVICE_ID_INTEL_SNB_IMC	0x0100
 #define PCI_DEVICE_ID_INTEL_IVB_IMC	0x0154
-- 
2.39.2



More information about the U-Boot mailing list