[PATCH 03/11] gpio: Add support for ADI ADP5588 GPIO expander chips
Greg Malysa
greg.malysa at timesys.com
Wed May 15 23:57:40 CEST 2024
From: Nathan Barrett-Morrison <nathan.morrison at timesys.com>
This adds support for the ADP588 GPIO expander from Analog Devices. It
is accessed over I2C and provides up to 18 pins. It is largely a port of
the Linux driver developed by Michael Hennerich
<michael.hennerich at analog.com>
Signed-off-by: Ian Roberts <ian.roberts at timesys.com>
Signed-off-by: Greg Malysa <greg.malysa at timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas at analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal at analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs at analog.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison at timesys.com>
---
MAINTAINERS | 1 +
drivers/gpio/Kconfig | 8 ++
drivers/gpio/Makefile | 1 +
drivers/gpio/adp5588_gpio.c | 208 ++++++++++++++++++++++++++++++++++++
4 files changed, 218 insertions(+)
create mode 100644 drivers/gpio/adp5588_gpio.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 5d7b0f39ac..7d07d13dbc 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -610,6 +610,7 @@ T: git https://github.com/analogdevicesinc/lnxdsp-u-boot
F: arch/arm/include/asm/arch-adi/
F: arch/arm/mach-sc5xx/
F: drivers/clk/adi/
+F: drivers/gpio/adp5588_gpio.c
F: drivers/gpio/gpio-adi-adsp.c
F: drivers/pinctrl/pinctrl-adi-adsp.c
F: drivers/serial/serial_adi_uart4.c
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 142fe44533..37be5008f3 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -531,6 +531,14 @@ config DM_PCA953X
Now, max 24 bits chips and PCA953X compatible chips are
supported
+config ADP5588_GPIO
+ bool "ADP5588 GPIO expander driver"
+ depends on DM_GPIO && DM_I2C
+ help
+ Say yes here to support GPIO functionality of ADI ADP5588 chips.
+
+ The ADP5588 is an 18-port I2C GPIO expander and keypad controller.
+
config SPL_DM_PCA953X
bool "PCA95[357]x, PCA9698, TCA64xx, and MAX7310 I/O ports in SPL"
depends on SPL_DM_GPIO
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index ba58fbafd1..f3935638f9 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -72,6 +72,7 @@ obj-$(CONFIG_NOMADIK_GPIO) += nmk_gpio.o
obj-$(CONFIG_MAX7320_GPIO) += max7320_gpio.o
obj-$(CONFIG_$(SPL_)MAX77663_GPIO) += max77663_gpio.o
obj-$(CONFIG_SL28CPLD_GPIO) += sl28cpld-gpio.o
+obj-$(CONFIG_ADP5588_GPIO) += adp5588_gpio.o
obj-$(CONFIG_ZYNQMP_GPIO_MODEPIN) += zynqmp_gpio_modepin.o
obj-$(CONFIG_SLG7XL45106_I2C_GPO) += gpio_slg7xl45106.o
obj-$(CONFIG_FTGPIO010) += ftgpio010.o
diff --git a/drivers/gpio/adp5588_gpio.c b/drivers/gpio/adp5588_gpio.c
new file mode 100644
index 0000000000..d081e16989
--- /dev/null
+++ b/drivers/gpio/adp5588_gpio.c
@@ -0,0 +1,208 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * GPIO Chip driver for Analog Devices
+ * ADP5588/ADP5587 I/O Expander and QWERTY Keypad Controller
+ *
+ * (C) Copyright 2022 - Analog Devices, Inc.
+ *
+ * Written and/or maintained by Timesys Corporation
+ *
+ * Contact: Nathan Barrett-Morrison <nathan.morrison at timesys.com>
+ * Contact: Greg Malysa <greg.malysa at timesys.com>
+ *
+ * Based on Michael Hennerich's Linux driver:
+ * Michael Hennerich <michael.hennerich at analog.com>
+ *
+ */
+
+#include <dm.h>
+#include <i2c.h>
+#include <asm-generic/gpio.h>
+
+#define ADP5588_MAXGPIO 18
+#define ADP5588_BANK(offs) ((offs) >> 3)
+#define ADP5588_BIT(offs) (1u << ((offs) & 0x7))
+
+#define DEV_ID 0x00 /* Device ID */
+#define GPIO_DAT_STAT1 0x14 /* GPIO Data Status, Read twice to clear */
+#define GPIO_DAT_STAT2 0x15 /* GPIO Data Status, Read twice to clear */
+#define GPIO_DAT_STAT3 0x16 /* GPIO Data Status, Read twice to clear */
+#define GPIO_DAT_OUT1 0x17 /* GPIO DATA OUT */
+#define GPIO_DAT_OUT2 0x18 /* GPIO DATA OUT */
+#define GPIO_DAT_OUT3 0x19 /* GPIO DATA OUT */
+#define GPIO_INT_EN1 0x1A /* GPIO Interrupt Enable */
+#define GPIO_INT_EN2 0x1B /* GPIO Interrupt Enable */
+#define GPIO_INT_EN3 0x1C /* GPIO Interrupt Enable */
+#define KP_GPIO1 0x1D /* Keypad or GPIO Selection */
+#define KP_GPIO2 0x1E /* Keypad or GPIO Selection */
+#define KP_GPIO3 0x1F /* Keypad or GPIO Selection */
+#define GPIO_DIR1 0x23 /* GPIO Data Direction */
+#define GPIO_DIR2 0x24 /* GPIO Data Direction */
+#define GPIO_DIR3 0x25 /* GPIO Data Direction */
+#define GPIO_PULL1 0x2C /* GPIO Pull Disable */
+#define GPIO_PULL2 0x2D /* GPIO Pull Disable */
+#define GPIO_PULL3 0x2E /* GPIO Pull Disable */
+#define ID_MASK 0x0F
+
+struct adp5588_gpio {
+ u8 dat_out[3];
+ u8 dir[3];
+};
+
+static int adp5588_gpio_read(struct udevice *dev, u8 reg)
+{
+ int ret;
+ u8 val;
+
+ ret = dm_i2c_read(dev, reg, &val, 1);
+
+ if (ret < 0) {
+ pr_err("%s: read error\n", __func__);
+ return ret;
+ }
+
+ return val;
+}
+
+static int adp5588_gpio_write(struct udevice *dev, u8 reg, u8 val)
+{
+ int ret;
+
+ ret = dm_i2c_write(dev, reg, &val, 1);
+ if (ret < 0) {
+ pr_err("%s: write error\n", __func__);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int adp5588_get_value(struct udevice *dev, u32 offset)
+{
+ struct adp5588_gpio *plat = dev_get_plat(dev);
+ unsigned int bank = ADP5588_BANK(offset);
+ unsigned int bit = ADP5588_BIT(offset);
+ int val;
+
+ if (plat->dir[bank] & bit)
+ val = plat->dat_out[bank];
+ else
+ val = adp5588_gpio_read(dev, GPIO_DAT_STAT1 + bank);
+
+ return !!(val & bit);
+}
+
+static int adp5588_set_value(struct udevice *dev, u32 offset,
+ int32_t value)
+{
+ unsigned int bank, bit;
+ int ret;
+ struct adp5588_gpio *plat = dev_get_plat(dev);
+
+ bank = ADP5588_BANK(offset);
+ bit = ADP5588_BIT(offset);
+
+ if (value)
+ plat->dat_out[bank] |= bit;
+ else
+ plat->dat_out[bank] &= ~bit;
+
+ ret = adp5588_gpio_write(dev, GPIO_DAT_OUT1 + bank,
+ plat->dat_out[bank]);
+
+ return ret;
+}
+
+static int adp5588_direction_input(struct udevice *dev, u32 offset)
+{
+ int ret;
+ unsigned int bank;
+ struct adp5588_gpio *plat = dev_get_plat(dev);
+
+ bank = ADP5588_BANK(offset);
+
+ plat->dir[bank] &= ~ADP5588_BIT(offset);
+ ret = adp5588_gpio_write(dev, GPIO_DIR1 + bank, plat->dir[bank]);
+
+ return ret;
+}
+
+static int adp5588_direction_output(struct udevice *dev,
+ u32 offset, int value)
+{
+ int ret;
+ unsigned int bank, bit;
+ struct adp5588_gpio *plat = dev_get_plat(dev);
+
+ bank = ADP5588_BANK(offset);
+ bit = ADP5588_BIT(offset);
+
+ plat->dir[bank] |= bit;
+
+ if (value)
+ plat->dat_out[bank] |= bit;
+ else
+ plat->dat_out[bank] &= ~bit;
+
+ ret = adp5588_gpio_write(dev, GPIO_DAT_OUT1 + bank,
+ plat->dat_out[bank]);
+ ret |= adp5588_gpio_write(dev, GPIO_DIR1 + bank,
+ plat->dir[bank]);
+
+ return ret;
+}
+
+static int adp5588_ofdata_platdata(struct udevice *dev)
+{
+ struct adp5588_gpio *plat = dev_get_plat(dev);
+ struct gpio_dev_priv *priv = dev_get_uclass_priv(dev);
+ int node = dev_of_offset(dev);
+ int ret, i, revid;
+
+ priv->gpio_count = ADP5588_MAXGPIO;
+ priv->bank_name = fdt_get_name(gd->fdt_blob, node, NULL);
+
+ ret = adp5588_gpio_read(dev, DEV_ID);
+ if (ret < 0)
+ return ret;
+
+ revid = ret & ID_MASK;
+
+ printf("ADP5588 Detected: Rev %x, Rev ID %x\n", ret, revid);
+
+ for (i = 0, ret = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++) {
+ plat->dat_out[i] = adp5588_gpio_read(dev, GPIO_DAT_OUT1 + i);
+ plat->dir[i] = adp5588_gpio_read(dev, GPIO_DIR1 + i);
+ ret |= adp5588_gpio_write(dev, KP_GPIO1 + i, 0);
+ ret |= adp5588_gpio_write(dev, GPIO_PULL1 + i, 0);
+ ret |= adp5588_gpio_write(dev, GPIO_INT_EN1 + i, 0);
+ if (ret) {
+ pr_err("%s: Initialization error\n", __func__);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static const struct dm_gpio_ops adp5588_ops = {
+ .direction_input = adp5588_direction_input,
+ .direction_output = adp5588_direction_output,
+ .get_value = adp5588_get_value,
+ .set_value = adp5588_set_value,
+};
+
+static const struct udevice_id adp5588_of_match_list[] = {
+ { .compatible = "adi,adp5588"},
+ { /* sentinel */ }
+};
+
+U_BOOT_DRIVER(gpio_adp5588) = {
+ .name = "gpio_adp5588",
+ .id = UCLASS_GPIO,
+ .ops = &adp5588_ops,
+ .of_match = adp5588_of_match_list,
+ .of_to_plat = adp5588_ofdata_platdata,
+ .plat_auto = sizeof(struct adp5588_gpio),
+ .flags = DM_FLAG_PRE_RELOC,
+};
--
2.43.2
More information about the U-Boot
mailing list