[PATCH] arm: dts: mvebu: Migrate to upstream DT for Synology DS116 (Armada 385) board
Tony Dinh
mibodhi at gmail.com
Wed May 22 23:51:59 CEST 2024
Enable OF_UPSTREAM to use upstream DT and add marvell/ prefix to the
DEFAULT_DEVICE_TREE in DS116 defconfig. Remove current DTS in
arch/arm/dts/ directory.
Signed-off-by: Tony Dinh <mibodhi at gmail.com>
---
arch/arm/dts/Makefile | 1 -
arch/arm/dts/armada-385-synology-ds116.dts | 291 ---------------------
configs/ds116_defconfig | 3 +-
3 files changed, 2 insertions(+), 293 deletions(-)
delete mode 100644 arch/arm/dts/armada-385-synology-ds116.dts
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index a5c82ebf7a..75f7e616b4 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -155,7 +155,6 @@ dtb-$(CONFIG_ARCH_MVEBU) += \
armada-385-atl-x530.dtb \
armada-385-atl-x530DP.dtb \
armada-385-db-88f6820-amc.dtb \
- armada-385-synology-ds116.dtb \
armada-385-thecus-n2350.dtb \
armada-385-turris-omnia.dtb \
armada-388-clearfog.dtb \
diff --git a/arch/arm/dts/armada-385-synology-ds116.dts b/arch/arm/dts/armada-385-synology-ds116.dts
deleted file mode 100644
index 82a0373f7f..0000000000
--- a/arch/arm/dts/armada-385-synology-ds116.dts
+++ /dev/null
@@ -1,291 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Device Tree file for Synology DS116 NAS
- *
- * Copyright (C) 2017 Willy Tarreau <w at 1wt.eu>
- */
-
-/dts-v1/;
-#include "armada-385.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
- model = "Synology DS116";
- compatible = "marvell,a385-gp", "marvell,armada385", "marvell,armada380";
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory {
- device_type = "memory";
- reg = <0x00000000 0x40000000>; /* 1 GB */
- };
-
- soc {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
- MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
- MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
- MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
- MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
-
- internal-regs {
- i2c at 11000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
- status = "okay";
- clock-frequency = <100000>;
-
- eeprom at 57 {
- compatible = "atmel,24c64";
- reg = <0x57>;
- };
- };
-
- serial at 12000 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins>;
- status = "okay";
- };
-
- serial at 12100 {
- /* A PIC16F1829 is connected to uart1 at 9600 bps,
- * and takes single-character orders :
- * "1" : power off // already handled by the poweroff node
- * "2" : short beep
- * "3" : long beep
- * "4" : turn the power LED ON
- * "5" : flash the power LED
- * "6" : turn the power LED OFF
- * "7" : turn the status LED OFF
- * "8" : turn the status LED ON
- * "9" : flash the status LED
- * "A" : flash the motherboard LED (D8)
- * "B" : turn the motherboard LED OFF
- * "C" : hard reset
- */
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins>;
- status = "okay";
- };
-
- poweroff at 12100 {
- compatible = "synology,power-off";
- reg = <0x12100 0x100>;
- clocks = <&coreclk 0>;
- };
-
- ethernet at 70000 {
- pinctrl-names = "default";
- phy = <&phy0>;
- phy-mode = "sgmii";
- buffer-manager = <&bm>;
- bm,pool-long = <0>;
- status = "okay";
- };
-
- mdio at 72004 {
- pinctrl-names = "default";
- pinctrl-0 = <&mdio_pins>;
-
- phy0: ethernet-phy at 1 {
- reg = <1>;
- };
- };
-
- sata at a8000 {
- pinctrl-names = "default";
- pinctrl-0 = <&sata0_pins>;
- status = "okay";
- #address-cells = <1>;
- #size-cells = <0>;
-
- sata0: sata-port at 0 {
- reg = <0>;
- target-supply = <®_5v_sata0>;
- };
- };
-
- bm at c8000 {
- status = "okay";
- };
-
- usb3 at f0000 {
- usb-phy = <&usb3_0_phy>;
- status = "okay";
- };
-
- usb3 at f8000 {
- usb-phy = <&usb3_1_phy>;
- status = "okay";
- };
- };
-
- bm-bppi {
- status = "okay";
- };
-
- gpio-fan {
- compatible = "gpio-fan";
- gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>,
- <&gpio1 17 GPIO_ACTIVE_HIGH>,
- <&gpio1 16 GPIO_ACTIVE_HIGH>;
- gpio-fan,speed-map = < 0 0
- 1500 1
- 2500 2
- 3000 3
- 3400 4
- 3700 5
- 3900 6
- 4000 7>;
- #cooling-cells = <2>;
- };
-
- gpio-leds {
- compatible = "gpio-leds";
-
- /* The green part is on gpio0.20 which is also used by
- * sata0, and accesses to SATA disk 0 make it blink so it
- * doesn't need to be declared here.
- */
- orange {
- gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
- label = "ds116:orange:disk";
- default-state = "off";
- };
- };
- };
-
- usb3_0_phy: usb3_0_phy {
- compatible = "usb-nop-xceiv";
- vcc-supply = <®_usb3_0_vbus>;
- #phy-cells = <0>;
- };
-
- usb3_1_phy: usb3_1_phy {
- compatible = "usb-nop-xceiv";
- vcc-supply = <®_usb3_1_vbus>;
- #phy-cells = <0>;
- };
-
- reg_usb3_0_vbus: usb3-vbus0 {
- compatible = "regulator-fixed";
- regulator-name = "usb3-vbus0";
- pinctrl-names = "default";
- pinctrl-0 = <&xhci0_vbus_pins>;
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- enable-active-high;
- gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
- };
-
- reg_usb3_1_vbus: usb3-vbus1 {
- compatible = "regulator-fixed";
- regulator-name = "usb3-vbus1";
- pinctrl-names = "default";
- pinctrl-0 = <&xhci1_vbus_pins>;
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- enable-active-high;
- gpio = <&gpio1 27 GPIO_ACTIVE_HIGH>;
- };
-
- reg_sata0: pwr-sata0 {
- compatible = "regulator-fixed";
- regulator-name = "pwr_en_sata0";
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
- enable-active-high;
- regulator-boot-on;
- gpio = <&gpio0 15 GPIO_ACTIVE_HIGH>;
- };
-
- reg_5v_sata0: v5-sata0 {
- compatible = "regulator-fixed";
- regulator-name = "v5.0-sata0";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- vin-supply = <®_sata0>;
- };
-
- reg_12v_sata0: v12-sata0 {
- compatible = "regulator-fixed";
- regulator-name = "v12.0-sata0";
- regulator-min-microvolt = <12000000>;
- regulator-max-microvolt = <12000000>;
- vin-supply = <®_sata0>;
- };
-};
-
-&spi0 {
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>;
- status = "okay";
-
- spi-flash at 0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "macronix,mx25l6405d", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <50000000>;
- m25p,fast-read;
-
- /* Note: there is a redboot partition table despite u-boot
- * being used. The names presented here are the same as those
- * found in the FIS directory. There is also a small device
- * tree in the last 64kB of the RedBoot partition which is not
- * enumerated. The MAC address and the serial number are listed
- * in the "vendor" partition.
- */
- partition at 0 {
- label = "RedBoot";
- reg = <0x00000000 0x000f0000>;
- read-only;
- };
-
- partition at c0000 {
- label = "zImage";
- reg = <0x000f0000 0x002d0000>;
- };
-
- partition at 390000 {
- label = "rd.gz";
- reg = <0x003c0000 0x00410000>;
- };
-
- partition at 7d0000 {
- label = "vendor";
- reg = <0x007d0000 0x00010000>;
- read-only;
- };
-
- partition at 7e0000 {
- label = "RedBoot config";
- reg = <0x007e0000 0x00010000>;
- read-only;
- };
-
- partition at 7f0000 {
- label = "FIS directory";
- reg = <0x007f0000 0x00010000>;
- read-only;
- };
- };
-};
-
-&pinctrl {
- /* use only one pin for UART1, as mpp20 is used by sata0 */
- uart1_pins: uart-pins-1 {
- marvell,pins = "mpp19";
- marvell,function = "ua1";
- };
-
- xhci0_vbus_pins: xhci0_vbus_pins {
- marvell,pins = "mpp58";
- marvell,function = "gpio";
- };
- xhci1_vbus_pins: xhci1_vbus_pins {
- marvell,pins = "mpp59";
- marvell,function = "gpio";
- };
-};
diff --git a/configs/ds116_defconfig b/configs/ds116_defconfig
index 1fc7380216..bcc5f00fe5 100644
--- a/configs/ds116_defconfig
+++ b/configs/ds116_defconfig
@@ -16,7 +16,7 @@ CONFIG_SF_DEFAULT_SPEED=50000000
CONFIG_ENV_SIZE=0x10000
CONFIG_ENV_OFFSET=0x7E0000
CONFIG_ENV_SECT_SIZE=0x10000
-CONFIG_DEFAULT_DEVICE_TREE="armada-385-synology-ds116"
+CONFIG_DEFAULT_DEVICE_TREE="marvell/armada-385-synology-ds116"
CONFIG_SPL_TEXT_BASE=0x40000030
CONFIG_SPL_SERIAL=y
CONFIG_SPL_STACK=0x4002c000
@@ -56,6 +56,7 @@ CONFIG_CMD_CACHE=y
CONFIG_CMD_TIME=y
CONFIG_CMD_MTDPARTS=y
CONFIG_MTDPARTS_DEFAULT="mtdparts=spi0.0:1m(u-boot),7040k(kernel),64k(u-boot-env),-(data)"
+CONFIG_OF_UPSTREAM=y
CONFIG_ENV_OVERWRITE=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_VERSION_VARIABLE=y
--
2.39.2
More information about the U-Boot
mailing list