[PATCH] arm: dts: mvebu: Migrate to upstream DT for Synology DS116 (Armada 385) board
Sumit Garg
sumit.garg at linaro.org
Thu May 23 09:27:07 CEST 2024
On Thu, 23 May 2024 at 03:22, Tony Dinh <mibodhi at gmail.com> wrote:
>
> Enable OF_UPSTREAM to use upstream DT and add marvell/ prefix to the
> DEFAULT_DEVICE_TREE in DS116 defconfig. Remove current DTS in
> arch/arm/dts/ directory.
>
> Signed-off-by: Tony Dinh <mibodhi at gmail.com>
> ---
>
> arch/arm/dts/Makefile | 1 -
> arch/arm/dts/armada-385-synology-ds116.dts | 291 ---------------------
> configs/ds116_defconfig | 3 +-
> 3 files changed, 2 insertions(+), 293 deletions(-)
> delete mode 100644 arch/arm/dts/armada-385-synology-ds116.dts
>
Acked-by: Sumit Garg <sumit.garg at linaro.org>
-Sumit
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index a5c82ebf7a..75f7e616b4 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -155,7 +155,6 @@ dtb-$(CONFIG_ARCH_MVEBU) += \
> armada-385-atl-x530.dtb \
> armada-385-atl-x530DP.dtb \
> armada-385-db-88f6820-amc.dtb \
> - armada-385-synology-ds116.dtb \
> armada-385-thecus-n2350.dtb \
> armada-385-turris-omnia.dtb \
> armada-388-clearfog.dtb \
> diff --git a/arch/arm/dts/armada-385-synology-ds116.dts b/arch/arm/dts/armada-385-synology-ds116.dts
> deleted file mode 100644
> index 82a0373f7f..0000000000
> --- a/arch/arm/dts/armada-385-synology-ds116.dts
> +++ /dev/null
> @@ -1,291 +0,0 @@
> -// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> -/*
> - * Device Tree file for Synology DS116 NAS
> - *
> - * Copyright (C) 2017 Willy Tarreau <w at 1wt.eu>
> - */
> -
> -/dts-v1/;
> -#include "armada-385.dtsi"
> -#include <dt-bindings/gpio/gpio.h>
> -
> -/ {
> - model = "Synology DS116";
> - compatible = "marvell,a385-gp", "marvell,armada385", "marvell,armada380";
> -
> - chosen {
> - stdout-path = "serial0:115200n8";
> - };
> -
> - memory {
> - device_type = "memory";
> - reg = <0x00000000 0x40000000>; /* 1 GB */
> - };
> -
> - soc {
> - ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
> - MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
> - MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
> - MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
> - MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
> -
> - internal-regs {
> - i2c at 11000 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&i2c0_pins>;
> - status = "okay";
> - clock-frequency = <100000>;
> -
> - eeprom at 57 {
> - compatible = "atmel,24c64";
> - reg = <0x57>;
> - };
> - };
> -
> - serial at 12000 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&uart0_pins>;
> - status = "okay";
> - };
> -
> - serial at 12100 {
> - /* A PIC16F1829 is connected to uart1 at 9600 bps,
> - * and takes single-character orders :
> - * "1" : power off // already handled by the poweroff node
> - * "2" : short beep
> - * "3" : long beep
> - * "4" : turn the power LED ON
> - * "5" : flash the power LED
> - * "6" : turn the power LED OFF
> - * "7" : turn the status LED OFF
> - * "8" : turn the status LED ON
> - * "9" : flash the status LED
> - * "A" : flash the motherboard LED (D8)
> - * "B" : turn the motherboard LED OFF
> - * "C" : hard reset
> - */
> - pinctrl-names = "default";
> - pinctrl-0 = <&uart1_pins>;
> - status = "okay";
> - };
> -
> - poweroff at 12100 {
> - compatible = "synology,power-off";
> - reg = <0x12100 0x100>;
> - clocks = <&coreclk 0>;
> - };
> -
> - ethernet at 70000 {
> - pinctrl-names = "default";
> - phy = <&phy0>;
> - phy-mode = "sgmii";
> - buffer-manager = <&bm>;
> - bm,pool-long = <0>;
> - status = "okay";
> - };
> -
> - mdio at 72004 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&mdio_pins>;
> -
> - phy0: ethernet-phy at 1 {
> - reg = <1>;
> - };
> - };
> -
> - sata at a8000 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&sata0_pins>;
> - status = "okay";
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - sata0: sata-port at 0 {
> - reg = <0>;
> - target-supply = <®_5v_sata0>;
> - };
> - };
> -
> - bm at c8000 {
> - status = "okay";
> - };
> -
> - usb3 at f0000 {
> - usb-phy = <&usb3_0_phy>;
> - status = "okay";
> - };
> -
> - usb3 at f8000 {
> - usb-phy = <&usb3_1_phy>;
> - status = "okay";
> - };
> - };
> -
> - bm-bppi {
> - status = "okay";
> - };
> -
> - gpio-fan {
> - compatible = "gpio-fan";
> - gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>,
> - <&gpio1 17 GPIO_ACTIVE_HIGH>,
> - <&gpio1 16 GPIO_ACTIVE_HIGH>;
> - gpio-fan,speed-map = < 0 0
> - 1500 1
> - 2500 2
> - 3000 3
> - 3400 4
> - 3700 5
> - 3900 6
> - 4000 7>;
> - #cooling-cells = <2>;
> - };
> -
> - gpio-leds {
> - compatible = "gpio-leds";
> -
> - /* The green part is on gpio0.20 which is also used by
> - * sata0, and accesses to SATA disk 0 make it blink so it
> - * doesn't need to be declared here.
> - */
> - orange {
> - gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
> - label = "ds116:orange:disk";
> - default-state = "off";
> - };
> - };
> - };
> -
> - usb3_0_phy: usb3_0_phy {
> - compatible = "usb-nop-xceiv";
> - vcc-supply = <®_usb3_0_vbus>;
> - #phy-cells = <0>;
> - };
> -
> - usb3_1_phy: usb3_1_phy {
> - compatible = "usb-nop-xceiv";
> - vcc-supply = <®_usb3_1_vbus>;
> - #phy-cells = <0>;
> - };
> -
> - reg_usb3_0_vbus: usb3-vbus0 {
> - compatible = "regulator-fixed";
> - regulator-name = "usb3-vbus0";
> - pinctrl-names = "default";
> - pinctrl-0 = <&xhci0_vbus_pins>;
> - regulator-min-microvolt = <5000000>;
> - regulator-max-microvolt = <5000000>;
> - enable-active-high;
> - gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
> - };
> -
> - reg_usb3_1_vbus: usb3-vbus1 {
> - compatible = "regulator-fixed";
> - regulator-name = "usb3-vbus1";
> - pinctrl-names = "default";
> - pinctrl-0 = <&xhci1_vbus_pins>;
> - regulator-min-microvolt = <5000000>;
> - regulator-max-microvolt = <5000000>;
> - enable-active-high;
> - gpio = <&gpio1 27 GPIO_ACTIVE_HIGH>;
> - };
> -
> - reg_sata0: pwr-sata0 {
> - compatible = "regulator-fixed";
> - regulator-name = "pwr_en_sata0";
> - regulator-min-microvolt = <12000000>;
> - regulator-max-microvolt = <12000000>;
> - enable-active-high;
> - regulator-boot-on;
> - gpio = <&gpio0 15 GPIO_ACTIVE_HIGH>;
> - };
> -
> - reg_5v_sata0: v5-sata0 {
> - compatible = "regulator-fixed";
> - regulator-name = "v5.0-sata0";
> - regulator-min-microvolt = <5000000>;
> - regulator-max-microvolt = <5000000>;
> - vin-supply = <®_sata0>;
> - };
> -
> - reg_12v_sata0: v12-sata0 {
> - compatible = "regulator-fixed";
> - regulator-name = "v12.0-sata0";
> - regulator-min-microvolt = <12000000>;
> - regulator-max-microvolt = <12000000>;
> - vin-supply = <®_sata0>;
> - };
> -};
> -
> -&spi0 {
> - pinctrl-names = "default";
> - pinctrl-0 = <&spi0_pins>;
> - status = "okay";
> -
> - spi-flash at 0 {
> - #address-cells = <1>;
> - #size-cells = <1>;
> - compatible = "macronix,mx25l6405d", "jedec,spi-nor";
> - reg = <0>; /* Chip select 0 */
> - spi-max-frequency = <50000000>;
> - m25p,fast-read;
> -
> - /* Note: there is a redboot partition table despite u-boot
> - * being used. The names presented here are the same as those
> - * found in the FIS directory. There is also a small device
> - * tree in the last 64kB of the RedBoot partition which is not
> - * enumerated. The MAC address and the serial number are listed
> - * in the "vendor" partition.
> - */
> - partition at 0 {
> - label = "RedBoot";
> - reg = <0x00000000 0x000f0000>;
> - read-only;
> - };
> -
> - partition at c0000 {
> - label = "zImage";
> - reg = <0x000f0000 0x002d0000>;
> - };
> -
> - partition at 390000 {
> - label = "rd.gz";
> - reg = <0x003c0000 0x00410000>;
> - };
> -
> - partition at 7d0000 {
> - label = "vendor";
> - reg = <0x007d0000 0x00010000>;
> - read-only;
> - };
> -
> - partition at 7e0000 {
> - label = "RedBoot config";
> - reg = <0x007e0000 0x00010000>;
> - read-only;
> - };
> -
> - partition at 7f0000 {
> - label = "FIS directory";
> - reg = <0x007f0000 0x00010000>;
> - read-only;
> - };
> - };
> -};
> -
> -&pinctrl {
> - /* use only one pin for UART1, as mpp20 is used by sata0 */
> - uart1_pins: uart-pins-1 {
> - marvell,pins = "mpp19";
> - marvell,function = "ua1";
> - };
> -
> - xhci0_vbus_pins: xhci0_vbus_pins {
> - marvell,pins = "mpp58";
> - marvell,function = "gpio";
> - };
> - xhci1_vbus_pins: xhci1_vbus_pins {
> - marvell,pins = "mpp59";
> - marvell,function = "gpio";
> - };
> -};
> diff --git a/configs/ds116_defconfig b/configs/ds116_defconfig
> index 1fc7380216..bcc5f00fe5 100644
> --- a/configs/ds116_defconfig
> +++ b/configs/ds116_defconfig
> @@ -16,7 +16,7 @@ CONFIG_SF_DEFAULT_SPEED=50000000
> CONFIG_ENV_SIZE=0x10000
> CONFIG_ENV_OFFSET=0x7E0000
> CONFIG_ENV_SECT_SIZE=0x10000
> -CONFIG_DEFAULT_DEVICE_TREE="armada-385-synology-ds116"
> +CONFIG_DEFAULT_DEVICE_TREE="marvell/armada-385-synology-ds116"
> CONFIG_SPL_TEXT_BASE=0x40000030
> CONFIG_SPL_SERIAL=y
> CONFIG_SPL_STACK=0x4002c000
> @@ -56,6 +56,7 @@ CONFIG_CMD_CACHE=y
> CONFIG_CMD_TIME=y
> CONFIG_CMD_MTDPARTS=y
> CONFIG_MTDPARTS_DEFAULT="mtdparts=spi0.0:1m(u-boot),7040k(kernel),64k(u-boot-env),-(data)"
> +CONFIG_OF_UPSTREAM=y
> CONFIG_ENV_OVERWRITE=y
> CONFIG_SYS_RELOC_GD_ENV_ADDR=y
> CONFIG_VERSION_VARIABLE=y
> --
> 2.39.2
>
More information about the U-Boot
mailing list