[PATCH 2/2] imx8mm-cl-iot-gate: Add support for the Realtek RTL8211E PHY
Fabio Estevam
festevam at gmail.com
Tue May 28 21:15:10 CEST 2024
From: Fabio Estevam <festevam at denx.de>
Newer imx8mm-cl-iot-gate versions are populated with a Realtek RTL8211E
PHY instead of the Atheros AR8033.
Adapted Compulab's patch from:
https://github.com/compulab-yokneam/meta-bsp-imx8mm/blob/iot-gate-imx8_5.10.72/recipes-bsp/u-boot/compulab/imx8mm/0125-imx8mm-net-enable-phy-Realtek-RTL8211E.patch
to support both PHYs in U-Boot.
Signed-off-by: Fabio Estevam <festevam at denx.de>
---
.../imx8mm-cl-iot-gate/imx8mm-cl-iot-gate.c | 106 +++++++++++++++++-
include/configs/imx8mm-cl-iot-gate.h | 2 +-
2 files changed, 104 insertions(+), 4 deletions(-)
diff --git a/board/compulab/imx8mm-cl-iot-gate/imx8mm-cl-iot-gate.c b/board/compulab/imx8mm-cl-iot-gate/imx8mm-cl-iot-gate.c
index af070ec315c4..bf196e062bd0 100644
--- a/board/compulab/imx8mm-cl-iot-gate/imx8mm-cl-iot-gate.c
+++ b/board/compulab/imx8mm-cl-iot-gate/imx8mm-cl-iot-gate.c
@@ -9,6 +9,7 @@
#include <efi_loader.h>
#include <env.h>
#include <extension_board.h>
+#include <fdt_support.h>
#include <hang.h>
#include <i2c.h>
#include <init.h>
@@ -31,6 +32,8 @@
DECLARE_GLOBAL_DATA_PTR;
+static int fec_phyaddr = -1;
+
#if IS_ENABLED(CONFIG_EFI_HAVE_CAPSULE_SUPPORT)
struct efi_fw_image fw_images[] = {
#if defined(CONFIG_TARGET_IMX8MM_CL_IOT_GATE)
@@ -110,10 +113,72 @@ static int setup_fec(void)
return 0;
}
+#define FDT_PHYADDR "/soc at 0/bus at 30800000/ethernet at 30be0000/mdio/ethernet-phy at 0"
+#define FLIP_32B(val) (((val >> 24) & 0xff) | ((val << 8) & 0xff0000) | ((val >> 8) & 0xff00) | ((val << 24) & 0xff000000))
+static int fdt_set_fec_phy_addr(void *blob)
+{
+ u32 val;
+
+ if (fec_phyaddr < 0)
+ return -EINVAL;
+
+ val = FLIP_32B(fec_phyaddr);
+ return fdt_find_and_setprop(blob, FDT_PHYADDR, "reg", (const void *)&val,
+ sizeof(val), 0);
+}
+
+int ft_board_setup(void *blob, struct bd_info *bd)
+{
+ fdt_set_fec_phy_addr(blob);
+ return 0;
+}
+
+/*
+ * These are specific ID, purposed to distiguish between PHY vendors.
+ * These values are not equal to real vendors' OUI (half of MAC address)
+ */
+#define OUI_PHY_ATHEROS 0x1374
+#define OUI_PHY_REALTEK 0x0732
+
int board_phy_config(struct phy_device *phydev)
{
- if (IS_ENABLED(CONFIG_FEC_MXC)) {
+ unsigned int model, rev, oui;
+ int phyid1, phyid2;
+ unsigned int reg;
+
+ if (!IS_ENABLED(CONFIG_FEC_MXC))
+ return 0;
+
+ phyid1 = phy_read(phydev, MDIO_DEVAD_NONE, MII_PHYSID1);
+ if (phyid1 < 0) {
+ printf("%s: PHYID1 registry read fail %i\n", __func__, phyid1);
+ return phyid1;
+ }
+
+ phyid2 = phy_read(phydev, MDIO_DEVAD_NONE, MII_PHYSID2);
+ if (phyid2 < 0) {
+ printf("%s: PHYID2 registry read fail %i\n", __func__, phyid2);
+ return phyid2;
+ }
+
+ reg = phyid2 | phyid1 << 16;
+ if (reg == 0xffff) {
+ printf("%s: There is no device @%i\n", __func__, phydev->addr);
+ return -ENODEV;
+ }
+
+ rev = reg & 0xf;
+ reg >>= 4;
+ model = reg & 0x3f;
+ reg >>= 6;
+ oui = reg;
+ debug("%s: PHY @0x%x OUI 0x%06x model 0x%x rev 0x%x\n",
+ __func__, phydev->addr, oui, model, rev);
+
+ switch (oui) {
+ case OUI_PHY_ATHEROS:
/* enable rgmii rxc skew and phy mode select to RGMII copper */
+ printf("phy: AR803x@%x\t", phydev->addr);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x8);
@@ -121,10 +186,45 @@ int board_phy_config(struct phy_device *phydev)
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x82ee);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+ break;
+ case OUI_PHY_REALTEK:
+ printf("phy: RTL8211E@%x\t", phydev->addr);
+ /* RTL8211E-VB-CG - add TX and RX delay */
+ unsigned short val;
+
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x07);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0xa4);
+ val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1c);
+ val |= (0x1 << 13) | (0x1 << 12) | (0x1 << 11);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1c, val);
+ /* LEDs: set to extension page */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x0007);
+ /* extension Page44 */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x002c);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1c, 0x0430);//LCR
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1a, 0x0010);//LACR
+ /*
+ * To disable EEE LED mode (blinking .4s/2s)
+ * Extension Page5
+ */
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x0005);
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x05, 0x8b82);//magic const
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x06, 0x052b);//magic const
+
+ phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x00);// Back to Page0
- if (phydev->drv->config)
- phydev->drv->config(phydev);
+ break;
+ default:
+ printf("%s: ERROR: unknown PHY @0x%x OUI 0x%06x model 0x%x rev 0x%x\n",
+ __func__, phydev->addr, oui, model, rev);
+ return -ENOSYS;
}
+
+ fec_phyaddr = phydev->addr;
+
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
return 0;
}
diff --git a/include/configs/imx8mm-cl-iot-gate.h b/include/configs/imx8mm-cl-iot-gate.h
index 09d87cf214bf..0c547027ba69 100644
--- a/include/configs/imx8mm-cl-iot-gate.h
+++ b/include/configs/imx8mm-cl-iot-gate.h
@@ -136,7 +136,7 @@
#define CFG_SYS_FSL_USDHC_NUM 2
#define CFG_SYS_FSL_ESDHC_ADDR 0
-#define CFG_FEC_MXC_PHYADDR 0
+#define CFG_FEC_MXC_PHYADDR -1 /* Auto search of PHY on MII */
/* USB Configs */
#define CFG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
--
2.34.1
More information about the U-Boot
mailing list