[PATCH v4 32/35] arm: mach-bcm283x: Add ARMV8_MULTIENTRY support
Simon Glass
sjg at chromium.org
Thu Sep 19 16:09:55 CEST 2024
Hi Patrick,
On Wed, 18 Sept 2024 at 17:27, Patrick Rudolph
<patrick.rudolph at 9elements.com> wrote:
>
> When ACPI is enabled over FDT the APs cannot be brought out of reset
> by the OS using the "FDT spin-table" mechanism, as no FDT is provided
> to the OS. The APs must be released out of reset in u-boot and then
> brought up in an ACPI compliant fashion.
>
> When ARMV8_MULTIENTRY is specified, the APs are released from reset
> and will enter U-Boot after it has been relocated as well.
>
> By default ARMV8_MULTIENTRY is not selected, keeping existing behaviour.
>
> TEST: All APs enter U-Boot when run on qemu-system-aarch64 and on
> real hardware.
>
> Signed-off-by: Patrick Rudolph <patrick.rudolph at 9elements.com>
> Cc: Matthias Brugger <mbrugger at suse.com>
> Cc: Peter Robinson <pbrobinson at gmail.com>
> Cc: Tom Rini <trini at konsulko.com>
> ---
> Changelog v2:
> - Drop CPU code from board
> - Add CPU driver to release APs from reset
> Changelog v4:
> - Use the generic armv8 CPU driver
> - Probe all CPUs
> - Release secondary CPUs in the probe function
> - Use of_to_plat() to parse DT
> - Drop udelay()
> - Select the GICv2 driver
> ---
> arch/arm/Kconfig | 1 +
> arch/arm/mach-bcm283x/Kconfig | 7 +-
> arch/arm/mach-bcm283x/init.c | 10 ++
> drivers/cpu/Makefile | 2 +-
> drivers/cpu/bcm283x_cpu.c | 218 ++++++++++++++++++++++++++++++++++
> 5 files changed, 236 insertions(+), 2 deletions(-)
> create mode 100644 drivers/cpu/bcm283x_cpu.c
Reviewed-by: Simon Glass <sjg at chromium.org>
With nits below
>
> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> index e85a7131d3..72702cd99c 100644
> --- a/arch/arm/Kconfig
> +++ b/arch/arm/Kconfig
> @@ -651,6 +651,7 @@ config ARCH_ORION5X
>
> config ARCH_BCM283X
> bool "Broadcom BCM283X family"
> + select CPU
> select DM
> select DM_GPIO
> select DM_SERIAL
> diff --git a/arch/arm/mach-bcm283x/Kconfig b/arch/arm/mach-bcm283x/Kconfig
> index b3287ce8bc..fad900d965 100644
> --- a/arch/arm/mach-bcm283x/Kconfig
> +++ b/arch/arm/mach-bcm283x/Kconfig
> @@ -12,6 +12,7 @@ config BCM2836
> config BCM2837
> bool "Broadcom BCM2837 SoC support"
> depends on ARCH_BCM283X
> + select ARCH_EARLY_INIT_R
>
> config BCM2837_32B
> bool "Broadcom BCM2837 SoC 32-bit support"
> @@ -24,11 +25,14 @@ config BCM2837_64B
> bool "Broadcom BCM2837 SoC 64-bit support"
> depends on ARCH_BCM283X
> select BCM2837
> + select DRIVER_GICV2
> select ARM64
> + select CPU_ARMV8
>
> config BCM2711
> bool "Broadcom BCM2711 SoC support"
> depends on ARCH_BCM283X
> + select ARCH_EARLY_INIT_R
>
> config BCM2711_32B
> bool "Broadcom BCM2711 SoC 32-bit support"
> @@ -42,11 +46,12 @@ config BCM2711_64B
> bool "Broadcom BCM2711 SoC 64-bit support"
> depends on ARCH_BCM283X
> select BCM2711
> + select DRIVER_GICV2
> select ARM64
> + select CPU_ARMV8
>
> menu "Broadcom BCM283X family"
> depends on ARCH_BCM283X
> -
> choice
> prompt "Broadcom BCM283X board select"
> optional
> diff --git a/arch/arm/mach-bcm283x/init.c b/arch/arm/mach-bcm283x/init.c
> index 7a1de22e0a..c59e557432 100644
> --- a/arch/arm/mach-bcm283x/init.c
> +++ b/arch/arm/mach-bcm283x/init.c
> @@ -9,6 +9,7 @@
> #include <cpu_func.h>
> #include <init.h>
> #include <dm/device.h>
> +#include <dm/uclass.h>
> #include <fdt_support.h>
> #include <asm/global_data.h>
All patches need to check header order, as noted before.
>
> @@ -199,6 +200,15 @@ int mach_cpu_init(void)
> "brcm,bcm2712-pm");
> if (offset > soc)
> rpi_wdog_base = fdt_get_base_address(gd->fdt_blob, offset);
> + return 0;
> +}
> +
> +int arch_early_init_r(void)
> +{
> + /* The older RPis do not have a CPU driver yet,\
/*
* The older...
Also please drop \
> + * thus do not check for errors here...
> + */
> + uclass_probe_all(UCLASS_CPU);
So should you check the compatible to know whether to check for errors?
>
> return 0;
> }
> diff --git a/drivers/cpu/Makefile b/drivers/cpu/Makefile
> index 773395693a..eaf494706e 100644
> --- a/drivers/cpu/Makefile
> +++ b/drivers/cpu/Makefile
> @@ -6,7 +6,7 @@
>
> obj-$(CONFIG_CPU) += cpu-uclass.o
>
> -
> +obj-$(CONFIG_ARCH_BCM283X) += bcm283x_cpu.o
> obj-$(CONFIG_ARCH_BMIPS) += bmips_cpu.o
> obj-$(CONFIG_ARCH_IMX8) += imx8_cpu.o
> obj-$(CONFIG_ARCH_AT91) += at91_cpu.o
> diff --git a/drivers/cpu/bcm283x_cpu.c b/drivers/cpu/bcm283x_cpu.c
> new file mode 100644
> index 0000000000..5ed75b3754
> --- /dev/null
> +++ b/drivers/cpu/bcm283x_cpu.c
> @@ -0,0 +1,218 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * Copyright 2024 9elements GmbH
> + */
> +
> +#include <acpi/acpigen.h>
> +#include <asm/cache.h>
> +#include <asm/io.h>
> +#include <asm/global_data.h>
> +#include <asm/system.h>
> +#include <asm/armv8/cpu.h>
> +#include <asm-generic/sections.h>
> +#include <cpu.h>
> +#include <cpu_func.h>
> +#include <dm.h>
> +#include <fdt_support.h>
> +#include <linux/bitops.h>
> +#include <linux/clk-provider.h>
> +#include <linux/delay.h>
> +#include "armv8_cpu.h"
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +struct bcm_plat {
> + u64 release_addr;
> +};
> +
> +static int cpu_bcm_get_desc(const struct udevice *dev, char *buf, int size)
> +{
> + struct cpu_plat *plat = dev_get_parent_plat(dev);
> + const char *name;
> + int ret;
> +
> + if (size < 32)
> + return -ENOSPC;
> +
> + if (device_is_compatible(dev, "arm,cortex-a53"))
> + name = "A53";
> + else if (device_is_compatible(dev, "arm,cortex-a72"))
> + name = "A72";
> + else
> + name = "?";
> +
> + ret = snprintf(buf, size, "Broadcom Cortex-%s at %u MHz\n",
> + name, plat->timebase_freq);
> +
> + return 0;
> +}
> +
> +static int cpu_bcm_get_info(const struct udevice *dev, struct cpu_info *info)
> +{
> + struct cpu_plat *plat = dev_get_parent_plat(dev);
> +
> + info->cpu_freq = plat->timebase_freq * 1000;
> + info->features = BIT(CPU_FEAT_L1_CACHE) | BIT(CPU_FEAT_MMU);
> +
> + return 0;
> +}
> +
> +static int cpu_bcm_get_count(const struct udevice *dev)
> +{
> + return uclass_id_count(UCLASS_CPU);
> +}
> +
> +static int cpu_bcm_get_vendor(const struct udevice *dev, char *buf, int size)
> +{
> + snprintf(buf, size, "Broadcom");
> +
> + return 0;
> +}
> +
> +static int cpu_bcm_is_current(struct udevice *dev)
> +{
> +#ifdef CONFIG_ARM64
Can you use if (IS_ENABLED(CONFIG_ARM64)) ?
> + struct cpu_plat *plat = dev_get_parent_plat(dev);
> +
> + if (plat->cpu_id == (read_mpidr() & 0xffff))
> + return 1;
> +#endif
> +
> + return 0;
> +}
> +
> +/**
> + * bcm_cpu_on - Releases the secondary CPU from it's spintable
> + *
> + * Write the CPU's spintable mailbox and let the CPU enter U-Boot.
> + *
> + * @dev: Device to start
> + * @return: zero on success or error code on failure.
> + */
> +static int bcm_cpu_on(struct udevice *dev)
> +{
> + struct bcm_plat *plat = dev_get_plat(dev);
> + ulong *start_address;
> +
> + if (!plat || plat->release_addr == ~0ULL)
plat cannot be NULL, right?
> + return -ENODATA;
> +
> + start_address = map_physmem(plat->release_addr, sizeof(uintptr_t), MAP_NOCACHE);
> +
> + /* Point secondary CPU to U-Boot entry */
> + *start_address = (uintptr_t)_start;
> +
> + /* Make sure the other CPUs see the written start address */
> + if (!CONFIG_IS_ENABLED(SYS_DCACHE_OFF))
> + flush_dcache_all();
> +
> + /* Send an event to wake up the secondary CPU. */
> + asm("dsb ishst\n"
> + "sev");
> +
> + unmap_physmem(start_address, MAP_NOCACHE);
> +
> + return 0;
> +}
> +
> +static const struct cpu_ops cpu_bcm_ops = {
> + .get_desc = cpu_bcm_get_desc,
> + .get_info = cpu_bcm_get_info,
> + .get_count = cpu_bcm_get_count,
> + .get_vendor = cpu_bcm_get_vendor,
> + .is_current = cpu_bcm_is_current,
> +};
> +
> +static const struct udevice_id cpu_bcm_ids[] = {
> + { .compatible = "arm,cortex-a53" }, /* RPi 3 */
> + { .compatible = "arm,cortex-a72" }, /* RPi 4 */
> + { }
> +};
> +
> +static int bcm_cpu_bind(struct udevice *dev)
> +{
> + struct cpu_plat *plat = dev_get_parent_plat(dev);
> +
> + plat->cpu_id = dev_read_addr(dev);
> +
> + return 0;
> +}
> +
> +/**
> + * bcm_cpu_of_to_plat - Gather spin-table release address
> + *
> + * Read the spin-table release address to allow all seconary CPUs to enter
> + * U-Boot when necessary.
> + *
> + * @dev: Device to start
> + */
> +static int bcm_cpu_of_to_plat(struct udevice *dev)
> +{
> + struct bcm_plat *plat = dev_get_plat(dev);
> + const char *prop;
> +
> + if (CONFIG_IS_ENABLED(ARMV8_MULTIENTRY)) {
> + plat->release_addr = ~0ULL;
> +
> + prop = dev_read_string(dev, "enable-method");
> + if (!prop || strcmp(prop, "spin-table"))
> + return -ENODEV;
> +
> + plat->release_addr = dev_read_u64_default(dev, "cpu-release-addr", ~0ULL);
> +
> + if (plat->release_addr == ~0ULL)
> + return -ENODEV;
> + }
> +
> + return 0;
> +}
> +
> +static int bcm_cpu_probe(struct udevice *dev)
> +{
> + struct cpu_plat *plat = dev_get_parent_plat(dev);
> + struct clk clk;
> + int ret;
> +
> + /* Get a clock if it exists */
> + ret = clk_get_by_index(dev, 0, &clk);
> + if (!ret) {
> + ret = clk_enable(&clk);
> + if (ret && (ret != -ENOSYS || ret != -EOPNOTSUPP))
> + return ret;
I don't think you need those internal brackets
> + ret = clk_get_rate(&clk);
> + if (IS_ERR_VALUE(ret))
> + return ret;
> + plat->timebase_freq = ret;
> + }
> +
> + /*
> + * The armstub holds the secondary CPUs in a spinloop. When
> + * ARMV8_MULTIENTRY is enabled release the secondary CPUs and
> + * let them enter U-Boot as well.
> + */
> + if (CONFIG_IS_ENABLED(ARMV8_MULTIENTRY)) {
> + ret = bcm_cpu_on(dev);
> + if (ret)
> + return ret;
> + }
> +
> + return ret;
> +}
> +
> +struct acpi_ops bcm283x_cpu_acpi_ops = {
> + .fill_ssdt = armv8_cpu_fill_ssdt,
> + .fill_madt = armv8_cpu_fill_madt,
> +};
> +
> +U_BOOT_DRIVER(cpu_bcm_drv) = {
> + .name = "bcm283x_cpu",
> + .id = UCLASS_CPU,
> + .of_match = cpu_bcm_ids,
> + .ops = &cpu_bcm_ops,
> + .probe = bcm_cpu_probe,
> + .bind = bcm_cpu_bind,
> + .of_to_plat = bcm_cpu_of_to_plat,
> + .plat_auto = sizeof(struct bcm_plat),
> + .flags = 0,
Drop that line, as 0 is the default
> + ACPI_OPS_PTR(&bcm283x_cpu_acpi_ops)
> +};
> --
> 2.46.0
>
Regards,
Simon
More information about the U-Boot
mailing list