[PATCH v3 6/8] doc: starfive: use consistent formatting

[Heinrich Schuchardt]

Always use ---- for the H2 level.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt at canonical.com>
---
v3:
	rebased upong Milk-V Mars CM removal patch
v2:
	new patch
---
 doc/board/starfive/milk-v_mars.rst   | 10 +++++-----
 doc/board/starfive/pine64_star64.rst | 12 ++++++------
 doc/board/starfive/visionfive2.rst   | 10 +++++-----
 3 files changed, 16 insertions(+), 16 deletions(-)

diff --git a/doc/board/starfive/milk-v_mars.rst b/doc/board/starfive/milk-v_mars.rst
index 554932ecfd4..aba9c9c53d4 100644
--- a/doc/board/starfive/milk-v_mars.rst
+++ b/doc/board/starfive/milk-v_mars.rst
@@ -8,7 +8,7 @@ board. In U-Boot SPL the actual board is detected and the device-tree patched
 accordingly.
 
 Building
-~~~~~~~~
+--------
 
 1. Add the RISC-V toolchain to your PATH.
 2. Setup ARCH & cross compilation environment variable:
@@ -40,7 +40,7 @@ This will generate the U-Boot SPL image (spl/u-boot-spl.bin.normal.out) as well
 as the FIT image (u-boot.itb) with OpenSBI and U-Boot.
 
 Device-tree selection
-~~~~~~~~~~~~~~~~~~~~~
+---------------------
 
 Depending on the board version U-Boot set variable $fdtfile to either
 starfive/jh7110-starfive-visionfive-2-v1.2a.dtb or
@@ -58,14 +58,14 @@ or the configuration variable CONFIG_DEFAULT_FDT_FILE can be used to set to
 provide a default value.
 
 Boot source selection
-~~~~~~~~~~~~~~~~~~~~~
+---------------------
 
 The board provides the DIP switches MSEL[1:0] to select the boot device out of
 SPI flash, eMMC, SD-card, UART. To select booting from SD-card set the DIP
 switches MSEL[1:0] to 10.
 
 Preparing the SD-Card
-~~~~~~~~~~~~~~~~~~~~~
+---------------------
 
 The device firmware loads U-Boot SPL (u-boot-spl.bin.normal.out) from the
 partition with type GUID 2E54B353-1271-4842-806F-E436D6AF6985. You are free
@@ -106,6 +106,6 @@ Copy U-Boot to the SD card
 	sudo umount /mnt
 
 Booting
-~~~~~~~
+-------
 
 Once you plugin the sdcard and power up, you should see the U-Boot prompt.
diff --git a/doc/board/starfive/pine64_star64.rst b/doc/board/starfive/pine64_star64.rst
index 52e9a907917..1df4b68e4a0 100644
--- a/doc/board/starfive/pine64_star64.rst
+++ b/doc/board/starfive/pine64_star64.rst
@@ -8,7 +8,7 @@ In U-Boot SPL the actual board is detected and the device-tree patched
 accordingly.
 
 Building
-~~~~~~~~
+--------
 
 1. Add the RISC-V toolchain to your PATH.
 2. Setup ARCH & cross compilation environment variable:
@@ -40,7 +40,7 @@ This will generate the U-Boot SPL image (spl/u-boot-spl.bin.normal.out) as well
 as the FIT image (u-boot.itb) with OpenSBI and U-Boot.
 
 Device-tree selection
-~~~~~~~~~~~~~~~~~~~~~
+---------------------
 
 U-Boot will set variable $fdtfile to starfive/jh7110-pine64-star64.dtb.
 
@@ -56,7 +56,7 @@ or the configuration variable CONFIG_DEFAULT_FDT_FILE can be used to set to
 provide a default value.
 
 Boot source selection
-~~~~~~~~~~~~~~~~~~~~~
+---------------------
 
 Boot mode is selected by an MSEL-DIP marked S1804 and GPIO_0 position adjacent
 to the 40pin GPIO header. ON/ONKE and number markings of the MSEL-DIP are
@@ -69,7 +69,7 @@ accurate selection.
 + UART: 11
 
 Preparing the SD-Card
-~~~~~~~~~~~~~~~~~~~~~
+---------------------
 
 The device firmware loads U-Boot SPL (u-boot-spl.bin.normal.out) from the
 partition with type GUID 2E54B353-1271-4842-806F-E436D6AF6985. You are free
@@ -110,12 +110,12 @@ Copy U-Boot to the SD card
 	sudo umount /mnt
 
 Booting
-~~~~~~~
+-------
 
 Once you plugin the sdcard and power up, you should see the U-Boot prompt.
 
 Serial Number and MAC address issues
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+------------------------------------
 
 U-Boot requires valid EEPROM data to determine which board-specific fix-up to
 apply at runtime. This affects the size of memory initialized, network mac
diff --git a/doc/board/starfive/visionfive2.rst b/doc/board/starfive/visionfive2.rst
index 2c68df3ce4d..44e7fcb3a48 100644
--- a/doc/board/starfive/visionfive2.rst
+++ b/doc/board/starfive/visionfive2.rst
@@ -36,7 +36,7 @@ Currently, the u-boot.itb is used as a dynamic of the OpenSBI FW_DYNAMIC
 firmware with the latest.
 
 Building
-~~~~~~~~
+--------
 
 1. Add the RISC-V toolchain to your PATH.
 2. Setup ARCH & cross compilation environment variable:
@@ -72,7 +72,7 @@ This will generate the U-Boot SPL image (spl/u-boot-spl.bin.normal.out) as well
 as the FIT image (u-boot.itb) with OpenSBI and U-Boot.
 
 Device-tree selection
-~~~~~~~~~~~~~~~~~~~~~
+---------------------
 
 Depending on the board version U-Boot set variable $fdtfile to either
 starfive/jh7110-starfive-visionfive-2-v1.2a.dtb or
@@ -90,7 +90,7 @@ or the configuration variable CONFIG_DEFAULT_FDT_FILE can be used to provide
 a default value.
 
 Flashing
-~~~~~~~~
+--------
 
 The device firmware loads U-Boot SPL (u-boot-spl.bin.normal.out) from the
 partition with type GUID 2E54B353-1271-4842-806F-E436D6AF6985. You are free
@@ -133,7 +133,7 @@ Program the SD card
 	sudo umount /mnt
 
 Booting
-~~~~~~~
+-------
 
 The board provides the DIP switches MSEL[1:0] to select the boot device.
 To select booting from SD-card set the DIP switches MSEL[1:0] to 10.
@@ -141,7 +141,7 @@ To select booting from SD-card set the DIP switches MSEL[1:0] to 10.
 Once you plugin the sdcard and power up, you should see the U-Boot prompt.
 
 Sample boot log from StarFive VisionFive2 board
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+-----------------------------------------------
 
 .. code-block:: none
 
-- 
2.48.1