[PATCH v2 3/8] phy: sun4i-usb: Control supplies via the regulator uclass

[Jernej Škrabec]

Dne sreda, 9. april 2025 ob 02:20:31 Srednjeevropski poletni čas je Andre Przywara napisal(a):
> From: Samuel Holland <samuel at sholland.org>
> 
> The device tree binding for the PHY provides VBUS supplies as regulator
> references. Now that all boards have the appropriate regulator uclass
> drivers enabled, the PHY driver can switch to using them. This replaces
> direct GPIO usage, which in some cases needed a special DM-incompatible
> "virtual" GPIO from the PMIC.
> 
> The following boards provided a value for CONFIG_USB0_VBUS_PIN, but are
> missing the "usb0_vbus-supply" property in their device tree. None of
> them have the MUSB controller enabled in host or OTG mode, so they
> should see no impact:
>  - Ainol_AW1_defconfig / sun7i-a20-ainol-aw1
>  - Ampe_A76_defconfig / sun5i-a13-ampe-a76
>  - CHIP_pro_defconfig / sun5i-gr8-chip-pro
>  - Cubieboard4_defconfig / sun9i-a80-cubieboard4
>  - Merrii_A80_Optimus_defconfig / sun9i-a80-optimus
>  - Sunchip_CX-A99_defconfig / sun9i-a80-cx-a99
>  - Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078
>  - Yones_Toptech_BS1078_V2_defconfig /
>    sun6i-a31s-yones-toptech-bs1078-v2
>  - iNet_3F_defconfig / sun4i-a10-inet-3f
>  - iNet_3W_defconfig / sun4i-a10-inet-3w
>  - iNet_86VS_defconfig / sun5i-a13-inet-86vs
>  - iNet_D978_rev2_defconfig / sun8i-a33-inet-d978-rev2
>  - icnova-a20-swac_defconfig / sun7i-a20-icnova-swac
>  - sun8i_a23_evb_defconfig / sun8i-a23-evb
> 
> Similarly, the following boards set CONFIG_USB1_VBUS_PIN, but do not
> have "usb1_vbus-supply" in their device tree. Neither of them have USB
> enabled at all, so again there should be no impact:
>  - Cubieboard4_defconfig / sun9i-a80-cubieboard4 (also for USB3)
>  - sun8i_a23_evb_defconfig / sun8i-a23-evb
> 
> The following boards use a different pin for USB1 VBUS between their
> defconfig and their device tree. Depending on which is correct, they
> may be broken:
>  - Linksprite_pcDuino3_Nano_defconfig (PH11) /
>    sun7i-a20-pcduino3-nano (PD2)
>  - icnova-a20-swac_defconfig (PG10) / sun7i-a20-icnova-swac (PH6)
> 
> Finally, this board has conflicting pins given for its USB2 VBUS:
>  - Lamobo_R1_defconfig (PH3) / sun7i-a20-lamobo-r1 (PH12)
> 
> Signed-off-by: Samuel Holland <samuel at sholland.org>
> [Andre: use regulator_set_enable_if_allowed()]
> Signed-off-by: Andre Przywara <andre.przywara at arm.com>

Reviewed-by: Jernej Skrabec <jernej.skrabec at gmail.com>

Best regards,
Jernej