[PATCH v3 3/4] board: bsh: imx6ulz_smm_m2: Add support for 512 MiB DRAM
Dario Binacchi
dario.binacchi at amarulasolutions.com
Wed May 21 11:47:31 CEST 2025
From: Michael Bode <michael.bode at bshg.com>
Calibration values were calculated using the NXP tool
I.MX6ULL_DDR3_Script_Aid_V0.01.xlsx
Signed-off-by: Michael Bode <michael.bode at bshg.com>
Signed-off-by: Michael Trimarchi <michael at amarulasolutions.com>
Signed-off-by: Dario Binacchi <dario.binacchi at amarulasolutions.com>
---
(no changes since v2)
Changes in v2:
- Use standard C comment style
board/bsh/imx6ulz_smm_m2/Makefile | 3 +-
board/bsh/imx6ulz_smm_m2/ddr3l_timing_512m.c | 168 +++++++++++++++++++
board/bsh/imx6ulz_smm_m2/spl.c | 9 +-
board/bsh/imx6ulz_smm_m2/spl_mtypes.h | 1 +
4 files changed, 176 insertions(+), 5 deletions(-)
create mode 100644 board/bsh/imx6ulz_smm_m2/ddr3l_timing_512m.c
diff --git a/board/bsh/imx6ulz_smm_m2/Makefile b/board/bsh/imx6ulz_smm_m2/Makefile
index d448f4fc5215..4f4d67f659d0 100644
--- a/board/bsh/imx6ulz_smm_m2/Makefile
+++ b/board/bsh/imx6ulz_smm_m2/Makefile
@@ -2,5 +2,4 @@
# (C) Copyright 2021 Amarula Solutions B.V.
obj-y := imx6ulz_smm_m2.o
-obj-$(CONFIG_XPL_BUILD) += spl.o ddr3l_timing_256m.o ddr3l_timing_128m.o
-
+obj-$(CONFIG_XPL_BUILD) += spl.o ddr3l_timing_512m.o ddr3l_timing_256m.o ddr3l_timing_128m.o
diff --git a/board/bsh/imx6ulz_smm_m2/ddr3l_timing_512m.c b/board/bsh/imx6ulz_smm_m2/ddr3l_timing_512m.c
new file mode 100644
index 000000000000..f5989382f5aa
--- /dev/null
+++ b/board/bsh/imx6ulz_smm_m2/ddr3l_timing_512m.c
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include "spl_mtypes.h"
+
+static const struct dram_cfg_param ddr_ddrc_cfg_512mb[] = {
+ /*
+ * =============================================================================
+ * IOMUX
+ * =============================================================================
+ */
+
+ /* DDR IO Type: */
+ {0x020e04b4, 0x000C0000}, /* IOMUXC_SW_PAD_CTL_GRP_DDR_TYPE */
+ {0x020e04ac, 0x00000000}, /* IOMUXC_SW_PAD_CTL_GRP_DDRPKE */
+
+ /* Clock: */
+ {0x020e027c, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK_0 */
+
+ /* Address: */
+ {0x020e0250, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_CAS */
+ {0x020e024c, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RAS */
+ {0x020e0490, 0x00000028}, /* IOMUXC_SW_PAD_CTL_GRP_ADDDS */
+
+ /* Control: */
+ {0x020e0288, 0x000C0028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_RESET */
+ {0x020e0270, 0x00000000}, /*
+ * IOMUXC_SW_PAD_CTL_PAD_DRAM_SDBA2 - DSE can be configured using
+ * Group Control Register: IOMUXC_SW_PAD_CTL_GRP_CTLDS
+ */
+ {0x020e0260, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDODT0 */
+ {0x020e0264, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDODT1 */
+ {0x020e04a0, 0x00000028}, /* IOMUXC_SW_PAD_CTL_GRP_CTLDS */
+
+ /* Data Strobes: */
+ {0x020e0494, 0x00020000}, /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE_CTL */
+ {0x020e0280, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0 */
+ {0x020e0284, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1 */
+
+ /* Data: */
+ {0x020e04b0, 0x00020000}, /* IOMUXC_SW_PAD_CTL_GRP_DDRMODE */
+ {0x020e0498, 0x00000028}, /* IOMUXC_SW_PAD_CTL_GRP_B0DS */
+ {0x020e04a4, 0x00000028}, /* IOMUXC_SW_PAD_CTL_GRP_B1DS */
+
+ {0x020e0244, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM0 */
+ {0x020e0248, 0x00000028}, /* IOMUXC_SW_PAD_CTL_PAD_DRAM_DQM1 */
+
+ /*
+ * =============================================================================
+ * DDR Controller Registers
+ * =============================================================================
+ * Manufacturer:ISSI
+ * Device Part Number:IS43TR16640BL-125JBLI
+ * Clock Freq.: 400MHz
+ * Density per CS in Gb: 2
+ * Chip Selects used:1
+ * Number of Banks:8
+ * Row address: 14
+ * Column address: 10
+ * Data bus width16
+ * =============================================================================
+ */
+ {0x021b001c, 0x00008000}, /*
+ * MMDC0_MDSCR, set the Configuration request bit during
+ * MMDC set up
+ */
+
+ /*
+ * =============================================================================
+ * Calibration setup.
+ * =============================================================================
+ */
+ {0x021b0800, 0xA1390003}, /*
+ * DDR_PHY_P0_MPZQHWCTRL, enable both one-time & periodic
+ * HW ZQ calibration
+ */
+
+ /*
+ * For target board may need to run write leveling calibration to fine tune these settings
+ */
+ {0x021b080c, 0x00000000},
+
+ /* Read DQS Gating calibration */
+ {0x021b083c, 0x01440140}, /* MPDGCTRL0 PHY0 */
+
+ /* Read calibration */
+ {0x021b0848, 0x40403A3E}, /* MPRDDLCTL PHY0 */
+
+ /* Write calibration */
+ {0x021b0850, 0x4040322A}, /* MPWRDLCTL PHY0 */
+
+ /*
+ * Read data bit delay: 3 is the reccommended default value, although out of reset value
+ * is 0
+ */
+ {0x021b081c, 0x33333333}, /* MMDC_MPRDDQBY0DL */
+ {0x021b0820, 0x33333333}, /* MMDC_MPRDDQBY1DL */
+
+ /* Write data bit delay: */
+ {0x021b082c, 0xF3333333}, /* MMDC_MPWRDQBY0DL */
+ {0x021b0830, 0xF3333333}, /* MMDC_MPWRDQBY1DL */
+
+ /* DQS&CLK Duty Cycle */
+ {0x021b08c0, 0x00944009}, /* [MMDC_MPDCCR] MMDC Duty Cycle Control Register */
+
+ /* Complete calibration by forced measurement: */
+ {0x021b08b8, 0x00000800}, /* DDR_PHY_P0_MPMUR0, frc_msr */
+
+ /*
+ * =============================================================================
+ * Calibration setup end
+ * =============================================================================
+ */
+
+ /* MMDC init: */
+ {0x021b0004, 0x0002002D}, /* MMDC0_MDPDC */
+ {0x021b0008, 0x1B333030}, /* MMDC0_MDOTC */
+ {0x021b000c, 0x3F435333}, /* MMDC0_MDCFG0 */
+ {0x021b0010, 0xB68E0B63}, /* MMDC0_MDCFG1 */
+ {0x021b0014, 0x01FF00DB}, /* MMDC0_MDCFG2 */
+
+ /*
+ * MDMISC: RALAT kept to the high level of 5.
+ * MDMISC: consider reducing RALAT if your 528MHz board design allow that.
+ * Lower RALAT benefits:
+ * a. better operation at low frequency, for LPDDR2 freq < 100MHz, change RALAT to 3
+ * b. Small performence improvment
+ */
+ {0x021b0018, 0x00211740}, /* MMDC0_MDMISC */
+ {0x021b001c, 0x00008000}, /*
+ * MMDC0_MDSCR set the Configuration request bit during
+ * MMDC set up
+ */
+ {0x021b002c, 0x000026D2}, /* MMDC0_MDRWD */
+ {0x021b0030, 0x00431023}, /* MMDC0_MDOR */
+ {0x021b0040, 0x0000004F}, /* Chan0 CS0_END */
+ {0x021b0000, 0x84180000}, /* MMDC0_MDCTL */
+
+ {0x021b0890, 0x00400000}, /* MPPDCMPR2 */
+
+ /* Mode register writes */
+ {0x021b001c, 0x02808032}, /* MMDC0_MDSCR, MR2 write, CS0 */
+ {0x021b001c, 0x00008033}, /* MMDC0_MDSCR, MR3 write, CS0 */
+ {0x021b001c, 0x00048031}, /* MMDC0_MDSCR, MR1 write, CS0 */
+ {0x021b001c, 0x15208030}, /* MMDC0_MDSCR, MR0write, CS0 */
+ {0x021b001c, 0x04008040}, /* MMDC0_MDSCR, ZQ calibration command sent to device on CS0 */
+
+ {0x021b0020, 0x00007800}, /* MMDC0_MDREF */
+
+ {0x021b0818, 0x00000227}, /* DDR_PHY_P0_MPODTCTRL */
+
+ {0x021b0004, 0x0002552D}, /* MMDC0_MDPDC now SDCTL power down enabled */
+
+ {0x021b0404, 0x00011006}, /*
+ * MMDC0_MAPSR ADOPT power down enabled, MMDC will enter
+ * automatically to self-refresh while the number of idle
+ * cycle reached
+ */
+
+ {0x021b001c, 0x00000000}, /*
+ * MMDC0_MDSCR, clear this register (especially the configuration
+ * bit as initialization is complete)
+ */
+};
+
+struct dram_timing_info bsh_dram_timing_512mb = {
+ .ddrc_cfg = ddr_ddrc_cfg_512mb,
+ .ddrc_cfg_num = ARRAY_SIZE(ddr_ddrc_cfg_512mb),
+};
diff --git a/board/bsh/imx6ulz_smm_m2/spl.c b/board/bsh/imx6ulz_smm_m2/spl.c
index 85fd9e133eb3..e8255b6d2a62 100644
--- a/board/bsh/imx6ulz_smm_m2/spl.c
+++ b/board/bsh/imx6ulz_smm_m2/spl.c
@@ -54,16 +54,19 @@ static void ddr_cfg_write(const struct dram_timing_info *dram_timing_info)
static void spl_dram_init(void)
{
/* Configure memory to maximum supported size for detection */
- ddr_cfg_write(&bsh_dram_timing_256mb);
+ ddr_cfg_write(&bsh_dram_timing_512mb);
/* Detect memory physically present */
- gd->ram_size = get_ram_size((void *)CFG_SYS_SDRAM_BASE, SZ_256M);
+ gd->ram_size = get_ram_size((void *)CFG_SYS_SDRAM_BASE, SZ_512M);
/* Reconfigure memory for actual detected size */
switch (gd->ram_size) {
- case SZ_256M:
+ case SZ_512M:
/* Already configured, nothing to do */
break;
+ case SZ_256M:
+ ddr_cfg_write(&bsh_dram_timing_256mb);
+ break;
case SZ_128M:
default:
ddr_cfg_write(&bsh_dram_timing_128mb);
diff --git a/board/bsh/imx6ulz_smm_m2/spl_mtypes.h b/board/bsh/imx6ulz_smm_m2/spl_mtypes.h
index 2b517c316e0f..8da59881c833 100644
--- a/board/bsh/imx6ulz_smm_m2/spl_mtypes.h
+++ b/board/bsh/imx6ulz_smm_m2/spl_mtypes.h
@@ -22,5 +22,6 @@ struct dram_timing_info {
extern struct dram_timing_info bsh_dram_timing_128mb;
extern struct dram_timing_info bsh_dram_timing_256mb;
+extern struct dram_timing_info bsh_dram_timing_512mb;
#endif /* SPL_MTYPES_H */
--
2.43.0
base-commit: a3e09b24ffd4429909604f1b28455b44306edbaa
branch: bsh-202505-RAM
More information about the U-Boot
mailing list