[PATCH 2/4] sunxi: switch Allwinner A80 boards to OF_UPSTREAM
Andre Przywara
andre.przywara at arm.com
Sun Oct 26 02:23:54 CET 2025
In contrast to some other Allwinner SoCs, there is no difference between
the DTs for the Allwinner A80 SoCs (sun9i) between the U-Boot and the
Linux kernel repository.
Remove the old copies of the A80 related .dts and .dtsi files, and switch
most of sun9i boards over to use OF_UPSTREAM.
There is the Sunchip CX-A99 (family of) board(s) for which we don't have
a DT in the kernel tree. Keep the .dts file in the legacy U-Boot DT
directory, and let the board's defconfig opt out of OF_UPSTREAM.
Signed-off-by: Andre Przywara <andre.przywara at arm.com>
---
arch/arm/dts/Makefile | 2 -
arch/arm/dts/sun9i-a80-cubieboard4.dts | 508 ----------
arch/arm/dts/sun9i-a80-optimus.dts | 510 ----------
arch/arm/dts/sun9i-a80.dtsi | 1253 ------------------------
arch/arm/mach-sunxi/Kconfig | 1 +
configs/Cubieboard4_defconfig | 2 +-
configs/Merrii_A80_Optimus_defconfig | 2 +-
configs/Sunchip_CX-A99_defconfig | 1 +
8 files changed, 4 insertions(+), 2275 deletions(-)
delete mode 100644 arch/arm/dts/sun9i-a80-cubieboard4.dts
delete mode 100644 arch/arm/dts/sun9i-a80-optimus.dts
delete mode 100644 arch/arm/dts/sun9i-a80.dtsi
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index bf0b52d4c4b..865ceb65f9a 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -691,8 +691,6 @@ dtb-$(CONFIG_MACH_SUN50I) += \
sun50i-a64-sopine-baseboard.dtb \
sun50i-a64-teres-i.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
- sun9i-a80-optimus.dtb \
- sun9i-a80-cubieboard4.dtb \
sun9i-a80-cx-a99.dtb
dtb-$(CONFIG_VF610) += vf610-colibri-eval-v3.dtb \
diff --git a/arch/arm/dts/sun9i-a80-cubieboard4.dts b/arch/arm/dts/sun9i-a80-cubieboard4.dts
deleted file mode 100644
index c8ca8cb7f5c..00000000000
--- a/arch/arm/dts/sun9i-a80-cubieboard4.dts
+++ /dev/null
@@ -1,508 +0,0 @@
-/*
- * Copyright 2015 Tyler Baker
- *
- * Tyler Baker <tyler.baker at linaro.org>
- * Chen-Yu Tsai <wens at csie.org>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "sun9i-a80.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
- model = "Cubietech Cubieboard4";
- compatible = "cubietech,a80-cubieboard4", "allwinner,sun9i-a80";
-
- aliases {
- serial0 = &uart0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- leds {
- compatible = "gpio-leds";
-
- led-0 {
- label = "cubieboard4:green:usr";
- gpios = <&pio 7 17 GPIO_ACTIVE_HIGH>; /* PH17 */
- };
-
- led-1 {
- label = "cubieboard4:red:usr";
- gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
- };
- };
-
- vga-connector {
- compatible = "vga-connector";
- label = "vga";
- ddc-i2c-bus = <&i2c3>;
-
- port {
- vga_con_in: endpoint {
- remote-endpoint = <&vga_dac_out>;
- };
- };
- };
-
- vga-dac {
- compatible = "corpro,gm7123", "adi,adv7123";
- vdd-supply = <®_dcdc1>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port at 0 {
- reg = <0>;
-
- vga_dac_in: endpoint {
- remote-endpoint = <&tcon0_out_vga>;
- };
- };
-
- port at 1 {
- reg = <1>;
-
- vga_dac_out: endpoint {
- remote-endpoint = <&vga_con_in>;
- };
- };
- };
- };
-
- wifi_pwrseq: wifi-pwrseq {
- compatible = "mmc-pwrseq-simple";
- clocks = <&ac100_rtc 1>;
- clock-names = "ext_clock";
- /* enables internal regulator and de-asserts reset */
- reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
- };
-};
-
-&de {
- status = "okay";
-};
-
-&gmac {
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_rgmii_pins>;
- phy-handle = <&phy1>;
- phy-mode = "rgmii-id";
- phy-supply = <®_cldo1>;
- status = "okay";
-};
-
-&i2c3 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c3_pins>;
- status = "okay";
-};
-
-&mdio {
- phy1: ethernet-phy at 1 {
- reg = <1>;
- };
-};
-
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins>;
- vmmc-supply = <®_dcdc1>;
- bus-width = <4>;
- cd-gpios = <&pio 7 18 GPIO_ACTIVE_LOW>; /* PH18 */
- status = "okay";
-};
-
-&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins>;
- vmmc-supply = <®_dldo1>;
- vqmmc-supply = <®_cldo3>;
- mmc-pwrseq = <&wifi_pwrseq>;
- bus-width = <4>;
- non-removable;
- status = "okay";
-};
-
-&mmc1_pins {
- bias-pull-up;
-};
-
-&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_8bit_pins>;
- vmmc-supply = <®_dcdc1>;
- bus-width = <8>;
- non-removable;
- cap-mmc-hw-reset;
- status = "okay";
-};
-
-&mmc2_8bit_pins {
- /* Increase drive strength for DDR modes */
- drive-strength = <40>;
-};
-
-&osc32k {
- /* osc32k input is from AC100 */
- clocks = <&ac100_rtc 0>;
-};
-
-&pio {
- vcc-pa-supply = <®_ldo_io1>;
- vcc-pb-supply = <®_aldo2>;
- vcc-pc-supply = <®_dcdc1>;
- vcc-pd-supply = <®_dc1sw>;
- vcc-pe-supply = <®_eldo2>;
- vcc-pf-supply = <®_dcdc1>;
- vcc-pg-supply = <®_ldo_io0>;
- vcc-ph-supply = <®_dcdc1>;
-};
-
-&r_ir {
- status = "okay";
-};
-
-&r_pio {
- vcc-pl-supply = <®_dldo2>;
- vcc-pm-supply = <®_eldo3>;
-};
-
-&r_rsb {
- status = "okay";
-
- axp809: pmic at 3a3 {
- reg = <0x3a3>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
- regulators {
- reg_aldo1: aldo1 {
- /*
- * TODO: This should be handled by the
- * USB PHY driver.
- */
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc33-usbh";
- };
-
- reg_aldo2: aldo2 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-name = "vcc-pb-io-cam";
- };
-
- aldo3 {
- /* unused */
- };
-
- reg_dc1sw: dc1sw {
- regulator-name = "vcc-pd";
- };
-
- reg_dc5ldo: dc5ldo {
- regulator-always-on;
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1100000>;
- regulator-name = "vdd-cpus-09-usbh";
- };
-
- reg_dcdc1: dcdc1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-3v";
- };
-
- reg_dcdc2: dcdc2 {
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1100000>;
- regulator-name = "vdd-gpu";
- };
-
- reg_dcdc3: dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1100000>;
- regulator-name = "vdd-cpua";
- };
-
- reg_dcdc4: dcdc4 {
- regulator-always-on;
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1100000>;
- regulator-name = "vdd-sys-usb0-hdmi";
- };
-
- reg_dcdc5: dcdc5 {
- regulator-always-on;
- regulator-min-microvolt = <1425000>;
- regulator-max-microvolt = <1575000>;
- regulator-name = "vcc-dram";
- };
-
- reg_dldo1: dldo1 {
- /*
- * The WiFi chip supports a wide range
- * (3.0 ~ 4.8V) of voltages, and so does
- * this regulator (3.0 ~ 4.2V), but
- * Allwinner SDK always sets it to 3.3V.
- */
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi";
- };
-
- reg_dldo2: dldo2 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-pl";
- };
-
- reg_eldo1: eldo1 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-name = "vcc-dvdd-cam";
- };
-
- reg_eldo2: eldo2 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-name = "vcc-pe";
- };
-
- reg_eldo3: eldo3 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-pm-codec-io1";
- };
-
- reg_ldo_io0: ldo_io0 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-pg";
- };
-
- reg_ldo_io1: ldo_io1 {
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <2500000>;
- regulator-name = "vcc-pa-gmac-2v5";
- };
-
- reg_rtc_ldo: rtc_ldo {
- regulator-name = "vcc-rtc-vdd1v8-io";
- };
-
- sw {
- /* unused */
- };
- };
- };
-
- axp806: pmic at 745 {
- compatible = "x-powers,axp806";
- reg = <0x745>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <1>;
- bldoin-supply = <®_dcdce>;
-
- regulators {
- reg_s_aldo1: aldo1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "avcc";
- };
-
- aldo2 {
- /*
- * unused, but use a different name to
- * avoid name clash with axp809's aldo's
- */
- regulator-name = "s_aldo2";
- };
-
- aldo3 {
- /*
- * unused, but use a different name to
- * avoid name clash with axp809's aldo's
- */
- regulator-name = "s_aldo3";
- };
-
- reg_bldo1: bldo1 {
- regulator-always-on;
- regulator-min-microvolt = <1700000>;
- regulator-max-microvolt = <1900000>;
- regulator-name = "vcc18-efuse-adc-display-csi";
- };
-
- reg_bldo2: bldo2 {
- regulator-always-on;
- regulator-min-microvolt = <1700000>;
- regulator-max-microvolt = <1900000>;
- regulator-name =
- "vdd18-drampll-vcc18-pll-cpvdd";
- };
-
- bldo3 {
- /* unused */
- };
-
- reg_bldo4: bldo4 {
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1300000>;
- regulator-name = "vcc12-hsic";
- };
-
- reg_cldo1: cldo1 {
- /*
- * This was 3V in the original design, but
- * 3.3V is the recommended supply voltage
- * for the Ethernet PHY.
- */
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- /*
- * The PHY requires 20ms after all voltages
- * are applied until core logic is ready and
- * 30ms after the reset pin is de-asserted.
- * Set a 100ms delay to account for PMIC
- * ramp time and board traces.
- */
- regulator-enable-ramp-delay = <100000>;
- regulator-name = "vcc-gmac-phy";
- };
-
- reg_cldo2: cldo2 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-name = "afvcc-cam";
- };
-
- reg_cldo3: cldo3 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-io-wifi-codec-io2";
- };
-
- reg_dcdca: dcdca {
- regulator-always-on;
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1100000>;
- regulator-name = "vdd-cpub";
- };
-
- reg_dcdcd: dcdcd {
- regulator-always-on;
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1100000>;
- regulator-name = "vdd-vpu";
- };
-
- reg_dcdce: dcdce {
- regulator-always-on;
- regulator-min-microvolt = <2100000>;
- regulator-max-microvolt = <2100000>;
- regulator-name = "vcc-bldo-codec-ldoin";
- };
-
- sw {
- /*
- * unused, but use a different name to
- * avoid name clash with axp809's sw
- */
- regulator-name = "s_sw";
- };
- };
- };
-
- ac100: codec at e89 {
- compatible = "x-powers,ac100";
- reg = <0xe89>;
-
- ac100_codec: codec {
- compatible = "x-powers,ac100-codec";
- interrupt-parent = <&r_pio>;
- interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */
- #clock-cells = <0>;
- clock-output-names = "4M_adda";
- };
-
- ac100_rtc: rtc {
- compatible = "x-powers,ac100-rtc";
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- clocks = <&ac100_codec>;
- #clock-cells = <1>;
- clock-output-names = "cko1_rtc",
- "cko2_rtc",
- "cko3_rtc";
- };
- };
-};
-
-#include "axp809.dtsi"
-
-&tcon0 {
- pinctrl-names = "default";
- pinctrl-0 = <&lcd0_rgb888_pins>;
-};
-
-&tcon0_out {
- tcon0_out_vga: endpoint {
- remote-endpoint = <&vga_dac_in>;
- };
-};
-
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_ph_pins>;
- status = "okay";
-};
diff --git a/arch/arm/dts/sun9i-a80-optimus.dts b/arch/arm/dts/sun9i-a80-optimus.dts
deleted file mode 100644
index 5c3580d712e..00000000000
--- a/arch/arm/dts/sun9i-a80-optimus.dts
+++ /dev/null
@@ -1,510 +0,0 @@
-/*
- * Copyright 2014 Chen-Yu Tsai
- *
- * Chen-Yu Tsai <wens at csie.org>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-#include "sun9i-a80.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
- model = "Merrii A80 Optimus Board";
- compatible = "merrii,a80-optimus", "allwinner,sun9i-a80";
-
- aliases {
- serial0 = &uart0;
- serial1 = &uart4;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- leds {
- compatible = "gpio-leds";
-
- /* The LED names match those found on the board */
- led2 {
- label = "optimus:led2:usr";
- gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>;
- };
-
- led3 {
- label = "optimus:led3:usr";
- gpios = <&r_pio 1 15 GPIO_ACTIVE_HIGH>; /* PM15 */
- };
-
- led4 {
- label = "optimus:led4:usr";
- gpios = <&pio 7 0 GPIO_ACTIVE_HIGH>;
- };
- };
-
- reg_usb1_vbus: usb1-vbus {
- compatible = "regulator-fixed";
- regulator-name = "usb1-vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- enable-active-high;
- gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
- };
-
- reg_usb3_vbus: usb3-vbus {
- compatible = "regulator-fixed";
- regulator-name = "usb3-vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- enable-active-high;
- gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */
- };
-
- wifi_pwrseq: wifi-pwrseq {
- compatible = "mmc-pwrseq-simple";
- clocks = <&ac100_rtc 1>;
- clock-names = "ext_clock";
- /* enables internal regulator and de-asserts reset */
- reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 WL-PMU-EN */
- };
-};
-
-&ehci0 {
- status = "okay";
-};
-
-&ehci1 {
- /* Enable if HSIC peripheral is connected */
- status = "disabled";
-};
-
-&ehci2 {
- status = "okay";
-};
-
-&gmac {
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_rgmii_pins>;
- phy-handle = <&phy1>;
- phy-mode = "rgmii-id";
- phy-supply = <®_cldo1>;
- status = "okay";
-};
-
-&mdio {
- phy1: ethernet-phy at 1 {
- reg = <1>;
- };
-};
-
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins>;
- vmmc-supply = <®_dcdc1>;
- bus-width = <4>;
- cd-gpios = <&pio 7 18 GPIO_ACTIVE_LOW>; /* PH8 */
- status = "okay";
-};
-
-&mmc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc1_pins>;
- vmmc-supply = <®_dldo1>;
- vqmmc-supply = <®_cldo3>;
- mmc-pwrseq = <&wifi_pwrseq>;
- bus-width = <4>;
- non-removable;
- status = "okay";
-};
-
-&mmc1_pins {
- bias-pull-up;
-};
-
-&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_8bit_pins>;
- vmmc-supply = <®_dcdc1>;
- bus-width = <8>;
- non-removable;
- cap-mmc-hw-reset;
- status = "okay";
-};
-
-&mmc2_8bit_pins {
- /* Increase drive strength for DDR modes */
- drive-strength = <40>;
-};
-
-&ohci0 {
- status = "okay";
-};
-
-&ohci2 {
- status = "okay";
-};
-
-&osc32k {
- /* osc32k input is from AC100 */
- clocks = <&ac100_rtc 0>;
-};
-
-&pio {
- vcc-pa-supply = <®_ldo_io1>;
- vcc-pb-supply = <®_aldo2>;
- vcc-pc-supply = <®_dcdc1>;
- vcc-pd-supply = <®_dcdc1>;
- vcc-pe-supply = <®_eldo2>;
- vcc-pf-supply = <®_dcdc1>;
- vcc-pg-supply = <®_ldo_io0>;
- vcc-ph-supply = <®_dcdc1>;
-};
-
-&r_ir {
- status = "okay";
-};
-
-&r_pio {
- vcc-pl-supply = <®_dldo2>;
- vcc-pm-supply = <®_eldo3>;
-};
-
-&r_rsb {
- status = "okay";
-
- axp809: pmic at 3a3 {
- reg = <0x3a3>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
- regulators {
- reg_aldo1: aldo1 {
- /*
- * TODO: This should be handled by the
- * USB PHY driver.
- */
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc33-usbh";
- };
-
- reg_aldo2: aldo2 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-name = "vcc-pb-io-cam";
- };
-
- aldo3 {
- /* unused */
- };
-
- reg_dc5ldo: dc5ldo {
- regulator-always-on;
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1100000>;
- regulator-name = "vdd-cpus-09-usbh";
- };
-
- dc1sw {
- /* unused */
- };
-
- reg_dcdc1: dcdc1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-3v";
- };
-
- reg_dcdc2: dcdc2 {
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1100000>;
- regulator-name = "vdd-gpu";
- };
-
- reg_dcdc3: dcdc3 {
- regulator-always-on;
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1100000>;
- regulator-name = "vdd-cpua";
- };
-
- reg_dcdc4: dcdc4 {
- regulator-always-on;
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1100000>;
- regulator-name = "vdd-sys-usb0-hdmi";
- };
-
- reg_dcdc5: dcdc5 {
- regulator-always-on;
- regulator-min-microvolt = <1425000>;
- regulator-max-microvolt = <1575000>;
- regulator-name = "vcc-dram";
- };
-
- reg_dldo1: dldo1 {
- /*
- * The WiFi chip supports a wide range
- * (3.0 ~ 4.8V) of voltages, and so does
- * this regulator (3.0 ~ 4.2V), but
- * Allwinner SDK always sets it to 3.3V.
- */
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-name = "vcc-wifi";
- };
-
- reg_dldo2: dldo2 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-pl";
- };
-
- reg_eldo1: eldo1 {
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-name = "vcc-dvdd-cam";
- };
-
- reg_eldo2: eldo2 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-name = "vcc-pe";
- };
-
- reg_eldo3: eldo3 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-pm-codec-io1";
- };
-
- reg_ldo_io0: ldo_io0 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-pg";
- };
-
- reg_ldo_io1: ldo_io1 {
- regulator-min-microvolt = <2500000>;
- regulator-max-microvolt = <2500000>;
- regulator-name = "vcc-pa-gmac-2v5";
- };
-
- reg_rtc_ldo: rtc_ldo {
- regulator-name = "vcc-rtc-vdd1v8-io";
- };
-
- sw {
- /* unused */
- };
- };
- };
-
- axp806: pmic at 745 {
- compatible = "x-powers,axp806";
- reg = <0x745>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #interrupt-cells = <1>;
- bldoin-supply = <®_dcdce>;
-
- regulators {
- reg_s_aldo1: aldo1 {
- regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "avcc";
- };
-
- aldo2 {
- /*
- * unused, but use a different name to
- * avoid name clash with axp809's aldo's
- */
- regulator-name = "s_aldo2";
- };
-
- aldo3 {
- /*
- * unused, but use a different name to
- * avoid name clash with axp809's aldo's
- */
- regulator-name = "s_aldo3";
- };
-
- reg_bldo1: bldo1 {
- regulator-always-on;
- regulator-min-microvolt = <1700000>;
- regulator-max-microvolt = <1900000>;
- regulator-name = "vcc18-efuse-adc-display-csi";
- };
-
- reg_bldo2: bldo2 {
- regulator-always-on;
- regulator-min-microvolt = <1700000>;
- regulator-max-microvolt = <1900000>;
- regulator-name =
- "vdd18-drampll-vcc18-pll-cpvdd";
- };
-
- bldo3 {
- /* unused */
- };
-
- reg_bldo4: bldo4 {
- regulator-min-microvolt = <1100000>;
- regulator-max-microvolt = <1300000>;
- regulator-name = "vcc12-hsic";
- };
-
- reg_cldo1: cldo1 {
- /*
- * This was 3V in the original design, but
- * 3.3V is the recommended supply voltage
- * for the Ethernet PHY.
- */
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- /*
- * The PHY requires 20ms after all voltages
- * are applied until core logic is ready and
- * 30ms after the reset pin is de-asserted.
- * Set a 100ms delay to account for PMIC
- * ramp time and board traces.
- */
- regulator-enable-ramp-delay = <100000>;
- regulator-name = "vcc-gmac-phy";
- };
-
- reg_cldo2: cldo2 {
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-name = "afvcc-cam";
- };
-
- reg_cldo3: cldo3 {
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-io-wifi-codec-io2";
- };
-
- reg_dcdca: dcdca {
- regulator-always-on;
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1100000>;
- regulator-name = "vdd-cpub";
- };
-
- reg_dcdcd: dcdcd {
- regulator-always-on;
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1100000>;
- regulator-name = "vdd-vpu";
- };
-
- reg_dcdce: dcdce {
- regulator-always-on;
- regulator-min-microvolt = <2100000>;
- regulator-max-microvolt = <2100000>;
- regulator-name = "vcc-bldo-codec-ldoin";
- };
-
- sw {
- /*
- * unused, but use a different name to
- * avoid name clash with axp809's sw
- */
- regulator-name = "s_sw";
- };
- };
- };
-
- ac100: codec at e89 {
- compatible = "x-powers,ac100";
- reg = <0xe89>;
-
- ac100_codec: codec {
- compatible = "x-powers,ac100-codec";
- interrupt-parent = <&r_pio>;
- interrupts = <0 9 IRQ_TYPE_LEVEL_LOW>; /* PL9 */
- #clock-cells = <0>;
- clock-output-names = "4M_adda";
- };
-
- ac100_rtc: rtc {
- compatible = "x-powers,ac100-rtc";
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
- clocks = <&ac100_codec>;
- #clock-cells = <1>;
- clock-output-names = "cko1_rtc",
- "cko2_rtc",
- "cko3_rtc";
- };
- };
-};
-
-#include "axp809.dtsi"
-
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_ph_pins>;
- status = "okay";
-};
-
-&usbphy1 {
- phy-supply = <®_usb1_vbus>;
- status = "okay";
-};
-
-&usbphy2 {
- phy-supply = <®_bldo4>;
- /* Enable if HSIC peripheral is connected */
- status = "disabled";
-};
-
-&usbphy3 {
- phy-supply = <®_usb3_vbus>;
- status = "okay";
-};
diff --git a/arch/arm/dts/sun9i-a80.dtsi b/arch/arm/dts/sun9i-a80.dtsi
deleted file mode 100644
index a1ae0929cec..00000000000
--- a/arch/arm/dts/sun9i-a80.dtsi
+++ /dev/null
@@ -1,1253 +0,0 @@
-/*
- * Copyright 2014 Chen-Yu Tsai
- *
- * Chen-Yu Tsai <wens at csie.org>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-
-#include <dt-bindings/clock/sun9i-a80-ccu.h>
-#include <dt-bindings/clock/sun9i-a80-de.h>
-#include <dt-bindings/clock/sun9i-a80-usb.h>
-#include <dt-bindings/reset/sun9i-a80-ccu.h>
-#include <dt-bindings/reset/sun9i-a80-de.h>
-#include <dt-bindings/reset/sun9i-a80-usb.h>
-
-/ {
- #address-cells = <2>;
- #size-cells = <2>;
- interrupt-parent = <&gic>;
-
- aliases {
- ethernet0 = &gmac;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu0: cpu at 0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- cci-control-port = <&cci_control0>;
- clock-frequency = <12000000>;
- enable-method = "allwinner,sun9i-a80-smp";
- reg = <0x0>;
- };
-
- cpu1: cpu at 1 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- cci-control-port = <&cci_control0>;
- clock-frequency = <12000000>;
- enable-method = "allwinner,sun9i-a80-smp";
- reg = <0x1>;
- };
-
- cpu2: cpu at 2 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- cci-control-port = <&cci_control0>;
- clock-frequency = <12000000>;
- enable-method = "allwinner,sun9i-a80-smp";
- reg = <0x2>;
- };
-
- cpu3: cpu at 3 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- cci-control-port = <&cci_control0>;
- clock-frequency = <12000000>;
- enable-method = "allwinner,sun9i-a80-smp";
- reg = <0x3>;
- };
-
- cpu4: cpu at 100 {
- compatible = "arm,cortex-a15";
- device_type = "cpu";
- cci-control-port = <&cci_control1>;
- clock-frequency = <18000000>;
- enable-method = "allwinner,sun9i-a80-smp";
- reg = <0x100>;
- };
-
- cpu5: cpu at 101 {
- compatible = "arm,cortex-a15";
- device_type = "cpu";
- cci-control-port = <&cci_control1>;
- clock-frequency = <18000000>;
- enable-method = "allwinner,sun9i-a80-smp";
- reg = <0x101>;
- };
-
- cpu6: cpu at 102 {
- compatible = "arm,cortex-a15";
- device_type = "cpu";
- cci-control-port = <&cci_control1>;
- clock-frequency = <18000000>;
- enable-method = "allwinner,sun9i-a80-smp";
- reg = <0x102>;
- };
-
- cpu7: cpu at 103 {
- compatible = "arm,cortex-a15";
- device_type = "cpu";
- cci-control-port = <&cci_control1>;
- clock-frequency = <18000000>;
- enable-method = "allwinner,sun9i-a80-smp";
- reg = <0x103>;
- };
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- clock-frequency = <24000000>;
- arm,cpu-registers-not-fw-configured;
- };
-
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- /*
- * map 64 bit address range down to 32 bits,
- * as the peripherals are all under 512MB.
- */
- ranges = <0 0 0 0x20000000>;
-
- /*
- * This clock is actually configurable from the PRCM address
- * space. The external 24M oscillator can be turned off, and
- * the clock switched to an internal 16M RC oscillator. Under
- * normal operation there's no reason to do this, and the
- * default is to use the external good one, so just model this
- * as a fixed clock. Also it is not entirely clear if the
- * osc24M mux in the PRCM affects the entire clock tree, which
- * would also throw all the PLL clock rates off, or just the
- * downstream clocks in the PRCM.
- */
- osc24M: clk-24M {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
- };
-
- /*
- * The 32k clock is from an external source, normally the
- * AC100 codec/RTC chip. This serves as a placeholder for
- * board dts files to specify the source.
- */
- osc32k: clk-32k {
- #clock-cells = <0>;
- compatible = "fixed-factor-clock";
- clock-div = <1>;
- clock-mult = <1>;
- clock-output-names = "osc32k";
- };
-
- /*
- * The following two are dummy clocks, placeholders
- * used in the gmac_tx clock. The gmac driver will
- * choose one parent depending on the PHY interface
- * mode, using clk_set_rate auto-reparenting.
- *
- * The actual TX clock rate is not controlled by the
- * gmac_tx clock.
- */
- mii_phy_tx_clk: mii-phy-tx-clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <25000000>;
- clock-output-names = "mii_phy_tx";
- };
-
- gmac_int_tx_clk: gmac-int-tx-clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <125000000>;
- clock-output-names = "gmac_int_tx";
- };
-
- gmac_tx_clk: clk at 800030 {
- #clock-cells = <0>;
- compatible = "allwinner,sun7i-a20-gmac-clk";
- reg = <0x00800030 0x4>;
- clocks = <&mii_phy_tx_clk>, <&gmac_int_tx_clk>;
- clock-output-names = "gmac_tx";
- };
-
- cpus_clk: clk at 8001410 {
- compatible = "allwinner,sun9i-a80-cpus-clk";
- reg = <0x08001410 0x4>;
- #clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>,
- <&ccu CLK_PLL_PERIPH0>,
- <&ccu CLK_PLL_AUDIO>;
- clock-output-names = "cpus";
- };
-
- ahbs: clk-ahbs {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <1>;
- clocks = <&cpus_clk>;
- clock-output-names = "ahbs";
- };
-
- apbs: clk at 800141c {
- compatible = "allwinner,sun8i-a23-apb0-clk";
- reg = <0x0800141c 0x4>;
- #clock-cells = <0>;
- clocks = <&ahbs>;
- clock-output-names = "apbs";
- };
-
- apbs_gates: clk at 8001428 {
- compatible = "allwinner,sun9i-a80-apbs-gates-clk";
- reg = <0x08001428 0x4>;
- #clock-cells = <1>;
- clocks = <&apbs>;
- clock-indices = <0>, <1>,
- <2>, <3>,
- <4>, <5>,
- <6>, <7>,
- <12>, <13>,
- <16>, <17>,
- <18>, <20>;
- clock-output-names = "apbs_pio", "apbs_ir",
- "apbs_timer", "apbs_rsb",
- "apbs_uart", "apbs_1wire",
- "apbs_i2c0", "apbs_i2c1",
- "apbs_ps2_0", "apbs_ps2_1",
- "apbs_dma", "apbs_i2s0",
- "apbs_i2s1", "apbs_twd";
- };
-
- r_1wire_clk: clk at 8001450 {
- reg = <0x08001450 0x4>;
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "r_1wire";
- };
-
- r_ir_clk: clk at 8001454 {
- reg = <0x08001454 0x4>;
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "r_ir";
- };
- };
-
- de: display-engine {
- compatible = "allwinner,sun9i-a80-display-engine";
- allwinner,pipelines = <&fe0>, <&fe1>;
- status = "disabled";
- };
-
- soc at 20000 {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- /*
- * map 64 bit address range down to 32 bits,
- * as the peripherals are all under 512MB.
- */
- ranges = <0 0 0 0x20000000>;
-
- sram_b: sram at 20000 {
- /* 256 KiB secure SRAM at 0x20000 */
- compatible = "mmio-sram";
- reg = <0x00020000 0x40000>;
-
- #address-cells = <1>;
- #size-cells = <1>;
- ranges = <0 0x00020000 0x40000>;
-
- smp-sram at 1000 {
- /*
- * This is checked by BROM to determine if
- * cpu0 should jump to SMP entry vector
- */
- compatible = "allwinner,sun9i-a80-smp-sram";
- reg = <0x1000 0x8>;
- };
- };
-
- gmac: ethernet at 830000 {
- compatible = "allwinner,sun7i-a20-gmac";
- reg = <0x00830000 0x1054>;
- interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "macirq";
- clocks = <&ccu CLK_BUS_GMAC>, <&gmac_tx_clk>;
- clock-names = "stmmaceth", "allwinner_gmac_tx";
- resets = <&ccu RST_BUS_GMAC>;
- reset-names = "stmmaceth";
- snps,pbl = <2>;
- snps,fixed-burst;
- snps,force_sf_dma_mode;
- status = "disabled";
-
- mdio: mdio {
- compatible = "snps,dwmac-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
- };
- };
-
- ehci0: usb at a00000 {
- compatible = "allwinner,sun9i-a80-ehci", "generic-ehci";
- reg = <0x00a00000 0x100>;
- interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&usb_clocks CLK_BUS_HCI0>;
- resets = <&usb_clocks RST_USB0_HCI>;
- phys = <&usbphy1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci0: usb at a00400 {
- compatible = "allwinner,sun9i-a80-ohci", "generic-ohci";
- reg = <0x00a00400 0x100>;
- interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&usb_clocks CLK_BUS_HCI0>,
- <&usb_clocks CLK_USB_OHCI0>;
- resets = <&usb_clocks RST_USB0_HCI>;
- phys = <&usbphy1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- usbphy1: phy at a00800 {
- compatible = "allwinner,sun9i-a80-usb-phy";
- reg = <0x00a00800 0x4>;
- clocks = <&usb_clocks CLK_USB0_PHY>;
- clock-names = "phy";
- resets = <&usb_clocks RST_USB0_PHY>;
- reset-names = "phy";
- status = "disabled";
- #phy-cells = <0>;
- };
-
- ehci1: usb at a01000 {
- compatible = "allwinner,sun9i-a80-ehci", "generic-ehci";
- reg = <0x00a01000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&usb_clocks CLK_BUS_HCI1>;
- resets = <&usb_clocks RST_USB1_HCI>;
- phys = <&usbphy2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- usbphy2: phy at a01800 {
- compatible = "allwinner,sun9i-a80-usb-phy";
- reg = <0x00a01800 0x4>;
- clocks = <&usb_clocks CLK_USB1_PHY>,
- <&usb_clocks CLK_USB_HSIC>,
- <&usb_clocks CLK_USB1_HSIC>;
- clock-names = "phy",
- "hsic_12M",
- "hsic_480M";
- resets = <&usb_clocks RST_USB1_PHY>,
- <&usb_clocks RST_USB1_HSIC>;
- reset-names = "phy",
- "hsic";
- status = "disabled";
- #phy-cells = <0>;
- /* usb1 is always used with HSIC */
- phy_type = "hsic";
- };
-
- ehci2: usb at a02000 {
- compatible = "allwinner,sun9i-a80-ehci", "generic-ehci";
- reg = <0x00a02000 0x100>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&usb_clocks CLK_BUS_HCI2>;
- resets = <&usb_clocks RST_USB2_HCI>;
- phys = <&usbphy3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci2: usb at a02400 {
- compatible = "allwinner,sun9i-a80-ohci", "generic-ohci";
- reg = <0x00a02400 0x100>;
- interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&usb_clocks CLK_BUS_HCI2>,
- <&usb_clocks CLK_USB_OHCI2>;
- resets = <&usb_clocks RST_USB2_HCI>;
- phys = <&usbphy3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- usbphy3: phy at a02800 {
- compatible = "allwinner,sun9i-a80-usb-phy";
- reg = <0x00a02800 0x4>;
- clocks = <&usb_clocks CLK_USB2_PHY>,
- <&usb_clocks CLK_USB_HSIC>,
- <&usb_clocks CLK_USB2_HSIC>;
- clock-names = "phy",
- "hsic_12M",
- "hsic_480M";
- resets = <&usb_clocks RST_USB2_PHY>,
- <&usb_clocks RST_USB2_HSIC>;
- reset-names = "phy",
- "hsic";
- status = "disabled";
- #phy-cells = <0>;
- };
-
- usb_clocks: clock at a08000 {
- compatible = "allwinner,sun9i-a80-usb-clks";
- reg = <0x00a08000 0x8>;
- clocks = <&ccu CLK_BUS_USB>, <&osc24M>;
- clock-names = "bus", "hosc";
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- cpucfg at 1700000 {
- compatible = "allwinner,sun9i-a80-cpucfg";
- reg = <0x01700000 0x100>;
- };
-
- crypto: crypto at 1c02000 {
- compatible = "allwinner,sun9i-a80-crypto";
- reg = <0x01c02000 0x1000>;
- interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
- resets = <&ccu RST_BUS_SS>;
- clocks = <&ccu CLK_BUS_SS>, <&ccu CLK_SS>;
- clock-names = "bus", "mod";
- };
-
- mmc0: mmc at 1c0f000 {
- compatible = "allwinner,sun9i-a80-mmc";
- reg = <0x01c0f000 0x1000>;
- clocks = <&mmc_config_clk 0>, <&ccu CLK_MMC0>,
- <&ccu CLK_MMC0_OUTPUT>,
- <&ccu CLK_MMC0_SAMPLE>;
- clock-names = "ahb", "mmc", "output", "sample";
- resets = <&mmc_config_clk 0>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc1: mmc at 1c10000 {
- compatible = "allwinner,sun9i-a80-mmc";
- reg = <0x01c10000 0x1000>;
- clocks = <&mmc_config_clk 1>, <&ccu CLK_MMC1>,
- <&ccu CLK_MMC1_OUTPUT>,
- <&ccu CLK_MMC1_SAMPLE>;
- clock-names = "ahb", "mmc", "output", "sample";
- resets = <&mmc_config_clk 1>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc2: mmc at 1c11000 {
- compatible = "allwinner,sun9i-a80-mmc";
- reg = <0x01c11000 0x1000>;
- clocks = <&mmc_config_clk 2>, <&ccu CLK_MMC2>,
- <&ccu CLK_MMC2_OUTPUT>,
- <&ccu CLK_MMC2_SAMPLE>;
- clock-names = "ahb", "mmc", "output", "sample";
- resets = <&mmc_config_clk 2>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc3: mmc at 1c12000 {
- compatible = "allwinner,sun9i-a80-mmc";
- reg = <0x01c12000 0x1000>;
- clocks = <&mmc_config_clk 3>, <&ccu CLK_MMC3>,
- <&ccu CLK_MMC3_OUTPUT>,
- <&ccu CLK_MMC3_SAMPLE>;
- clock-names = "ahb", "mmc", "output", "sample";
- resets = <&mmc_config_clk 3>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mmc_config_clk: clk at 1c13000 {
- compatible = "allwinner,sun9i-a80-mmc-config-clk";
- reg = <0x01c13000 0x10>;
- clocks = <&ccu CLK_BUS_MMC>;
- resets = <&ccu RST_BUS_MMC>;
- #clock-cells = <1>;
- #reset-cells = <1>;
- clock-output-names = "mmc0_config", "mmc1_config",
- "mmc2_config", "mmc3_config";
- };
-
- gic: interrupt-controller at 1c41000 {
- compatible = "arm,gic-400";
- reg = <0x01c41000 0x1000>,
- <0x01c42000 0x2000>,
- <0x01c44000 0x2000>,
- <0x01c46000 0x2000>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
- };
-
- cci: cci at 1c90000 {
- compatible = "arm,cci-400";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x01c90000 0x1000>;
- ranges = <0x0 0x01c90000 0x10000>;
-
- cci_control0: slave-if at 4000 {
- compatible = "arm,cci-400-ctrl-if";
- interface-type = "ace";
- reg = <0x4000 0x1000>;
- };
-
- cci_control1: slave-if at 5000 {
- compatible = "arm,cci-400-ctrl-if";
- interface-type = "ace";
- reg = <0x5000 0x1000>;
- };
-
- pmu at 9000 {
- compatible = "arm,cci-400-pmu,r1";
- reg = <0x9000 0x5000>;
- interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
- };
- };
-
- de_clocks: clock at 3000000 {
- compatible = "allwinner,sun9i-a80-de-clks";
- reg = <0x03000000 0x30>;
- clocks = <&ccu CLK_DE>,
- <&ccu CLK_SDRAM>,
- <&ccu CLK_BUS_DE>;
- clock-names = "mod",
- "dram",
- "bus";
- resets = <&ccu RST_BUS_DE>;
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- fe0: display-frontend at 3100000 {
- compatible = "allwinner,sun9i-a80-display-frontend";
- reg = <0x03100000 0x40000>;
- interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&de_clocks CLK_BUS_FE0>, <&de_clocks CLK_FE0>,
- <&de_clocks CLK_DRAM_FE0>;
- clock-names = "ahb", "mod",
- "ram";
- resets = <&de_clocks RST_FE0>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- fe0_out: port at 1 {
- reg = <1>;
-
- fe0_out_deu0: endpoint {
- remote-endpoint = <&deu0_in_fe0>;
- };
- };
- };
- };
-
- fe1: display-frontend at 3140000 {
- compatible = "allwinner,sun9i-a80-display-frontend";
- reg = <0x03140000 0x40000>;
- interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&de_clocks CLK_BUS_FE1>, <&de_clocks CLK_FE1>,
- <&de_clocks CLK_DRAM_FE1>;
- clock-names = "ahb", "mod",
- "ram";
- resets = <&de_clocks RST_FE0>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- fe1_out: port at 1 {
- reg = <1>;
-
- fe1_out_deu1: endpoint {
- remote-endpoint = <&deu1_in_fe1>;
- };
- };
- };
- };
-
- be0: display-backend at 3200000 {
- compatible = "allwinner,sun9i-a80-display-backend";
- reg = <0x03200000 0x40000>;
- interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&de_clocks CLK_BUS_BE0>, <&de_clocks CLK_BE0>,
- <&de_clocks CLK_DRAM_BE0>;
- clock-names = "ahb", "mod",
- "ram";
- resets = <&de_clocks RST_BE0>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- be0_in: port at 0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- be0_in_deu0: endpoint at 0 {
- reg = <0>;
- remote-endpoint = <&deu0_out_be0>;
- };
-
- be0_in_deu1: endpoint at 1 {
- reg = <1>;
- remote-endpoint = <&deu1_out_be0>;
- };
- };
-
- be0_out: port at 1 {
- reg = <1>;
-
- be0_out_drc0: endpoint {
- remote-endpoint = <&drc0_in_be0>;
- };
- };
- };
- };
-
- be1: display-backend at 3240000 {
- compatible = "allwinner,sun9i-a80-display-backend";
- reg = <0x03240000 0x40000>;
- interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&de_clocks CLK_BUS_BE1>, <&de_clocks CLK_BE1>,
- <&de_clocks CLK_DRAM_BE1>;
- clock-names = "ahb", "mod",
- "ram";
- resets = <&de_clocks RST_BE1>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- be1_in: port at 0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- be1_in_deu0: endpoint at 0 {
- reg = <0>;
- remote-endpoint = <&deu0_out_be1>;
- };
-
- be1_in_deu1: endpoint at 1 {
- reg = <1>;
- remote-endpoint = <&deu1_out_be1>;
- };
- };
-
- be1_out: port at 1 {
- reg = <1>;
-
- be1_out_drc1: endpoint {
- remote-endpoint = <&drc1_in_be1>;
- };
- };
- };
- };
-
- deu0: deu at 3300000 {
- compatible = "allwinner,sun9i-a80-deu";
- reg = <0x03300000 0x40000>;
- interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&de_clocks CLK_BUS_DEU0>,
- <&de_clocks CLK_IEP_DEU0>,
- <&de_clocks CLK_DRAM_DEU0>;
- clock-names = "ahb",
- "mod",
- "ram";
- resets = <&de_clocks RST_DEU0>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- deu0_in: port at 0 {
- reg = <0>;
-
- deu0_in_fe0: endpoint {
- remote-endpoint = <&fe0_out_deu0>;
- };
- };
-
- deu0_out: port at 1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- deu0_out_be0: endpoint at 0 {
- reg = <0>;
- remote-endpoint = <&be0_in_deu0>;
- };
-
- deu0_out_be1: endpoint at 1 {
- reg = <1>;
- remote-endpoint = <&be1_in_deu0>;
- };
- };
- };
- };
-
- deu1: deu at 3340000 {
- compatible = "allwinner,sun9i-a80-deu";
- reg = <0x03340000 0x40000>;
- interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&de_clocks CLK_BUS_DEU1>,
- <&de_clocks CLK_IEP_DEU1>,
- <&de_clocks CLK_DRAM_DEU1>;
- clock-names = "ahb",
- "mod",
- "ram";
- resets = <&de_clocks RST_DEU1>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- deu1_in: port at 0 {
- reg = <0>;
-
- deu1_in_fe1: endpoint {
- remote-endpoint = <&fe1_out_deu1>;
- };
- };
-
- deu1_out: port at 1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- deu1_out_be0: endpoint at 0 {
- reg = <0>;
- remote-endpoint = <&be0_in_deu1>;
- };
-
- deu1_out_be1: endpoint at 1 {
- reg = <1>;
- remote-endpoint = <&be1_in_deu1>;
- };
- };
- };
- };
-
- drc0: drc at 3400000 {
- compatible = "allwinner,sun9i-a80-drc";
- reg = <0x03400000 0x40000>;
- interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&de_clocks CLK_BUS_DRC0>,
- <&de_clocks CLK_IEP_DRC0>,
- <&de_clocks CLK_DRAM_DRC0>;
- clock-names = "ahb",
- "mod",
- "ram";
- resets = <&de_clocks RST_DRC0>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- drc0_in: port at 0 {
- reg = <0>;
-
- drc0_in_be0: endpoint {
- remote-endpoint = <&be0_out_drc0>;
- };
- };
-
- drc0_out: port at 1 {
- reg = <1>;
-
- drc0_out_tcon0: endpoint {
- remote-endpoint = <&tcon0_in_drc0>;
- };
- };
- };
- };
-
- drc1: drc at 3440000 {
- compatible = "allwinner,sun9i-a80-drc";
- reg = <0x03440000 0x40000>;
- interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&de_clocks CLK_BUS_DRC1>,
- <&de_clocks CLK_IEP_DRC1>,
- <&de_clocks CLK_DRAM_DRC1>;
- clock-names = "ahb",
- "mod",
- "ram";
- resets = <&de_clocks RST_DRC1>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- drc1_in: port at 0 {
- reg = <0>;
-
- drc1_in_be1: endpoint {
- remote-endpoint = <&be1_out_drc1>;
- };
- };
-
- drc1_out: port at 1 {
- reg = <1>;
-
- drc1_out_tcon1: endpoint {
- remote-endpoint = <&tcon1_in_drc1>;
- };
- };
- };
- };
-
- tcon0: lcd-controller at 3c00000 {
- compatible = "allwinner,sun9i-a80-tcon-lcd";
- reg = <0x03c00000 0x10000>;
- interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_LCD0>, <&ccu CLK_LCD0>;
- clock-names = "ahb", "tcon-ch0";
- resets = <&ccu RST_BUS_LCD0>,
- <&ccu RST_BUS_EDP>,
- <&ccu RST_BUS_LVDS>;
- reset-names = "lcd",
- "edp",
- "lvds";
- clock-output-names = "tcon0-pixel-clock";
- #clock-cells = <0>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- tcon0_in: port at 0 {
- reg = <0>;
-
- tcon0_in_drc0: endpoint {
- remote-endpoint = <&drc0_out_tcon0>;
- };
- };
-
- tcon0_out: port at 1 {
- reg = <1>;
- };
- };
- };
-
- tcon1: lcd-controller at 3c10000 {
- compatible = "allwinner,sun9i-a80-tcon-tv";
- reg = <0x03c10000 0x10000>;
- interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_LCD1>, <&ccu CLK_LCD1>;
- clock-names = "ahb", "tcon-ch1";
- resets = <&ccu RST_BUS_LCD1>, <&ccu RST_BUS_EDP>;
- reset-names = "lcd", "edp";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- tcon1_in: port at 0 {
- reg = <0>;
-
- tcon1_in_drc1: endpoint {
- remote-endpoint = <&drc1_out_tcon1>;
- };
- };
-
- tcon1_out: port at 1 {
- reg = <1>;
- };
- };
- };
-
- ccu: clock at 6000000 {
- compatible = "allwinner,sun9i-a80-ccu";
- reg = <0x06000000 0x800>;
- clocks = <&osc24M>, <&osc32k>;
- clock-names = "hosc", "losc";
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- timer at 6000c00 {
- compatible = "allwinner,sun4i-a10-timer";
- reg = <0x06000c00 0xa0>;
- interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
-
- clocks = <&osc24M>;
- };
-
- wdt: watchdog at 6000ca0 {
- compatible = "allwinner,sun6i-a31-wdt";
- reg = <0x06000ca0 0x20>;
- interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&osc24M>;
- };
-
- pio: pinctrl at 6000800 {
- compatible = "allwinner,sun9i-a80-pinctrl";
- reg = <0x06000800 0x400>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <3>;
- #gpio-cells = <3>;
-
- gmac_rgmii_pins: gmac-rgmii-pins {
- pins = "PA0", "PA1", "PA2", "PA3", "PA4", "PA5",
- "PA7", "PA8", "PA9", "PA10", "PA12",
- "PA13", "PA15", "PA16", "PA17";
- function = "gmac";
- /*
- * data lines in RGMII mode use DDR mode
- * and need a higher signal drive strength
- */
- drive-strength = <40>;
- };
-
- i2c3_pins: i2c3-pins {
- pins = "PG10", "PG11";
- function = "i2c3";
- };
-
- lcd0_rgb888_pins: lcd0-rgb888-pins {
- pins = "PD0", "PD1", "PD2", "PD3",
- "PD4", "PD5", "PD6", "PD7",
- "PD8", "PD9", "PD10", "PD11",
- "PD12", "PD13", "PD14", "PD15",
- "PD16", "PD17", "PD18", "PD19",
- "PD20", "PD21", "PD22", "PD23",
- "PD24", "PD25", "PD26", "PD27";
- function = "lcd0";
- };
-
- mmc0_pins: mmc0-pins {
- pins = "PF0", "PF1" ,"PF2", "PF3",
- "PF4", "PF5";
- function = "mmc0";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc1_pins: mmc1-pins {
- pins = "PG0", "PG1" ,"PG2", "PG3",
- "PG4", "PG5";
- function = "mmc1";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc2_8bit_pins: mmc2-8bit-pins {
- pins = "PC6", "PC7", "PC8", "PC9",
- "PC10", "PC11", "PC12",
- "PC13", "PC14", "PC15",
- "PC16";
- function = "mmc2";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- uart0_ph_pins: uart0-ph-pins {
- pins = "PH12", "PH13";
- function = "uart0";
- };
-
- uart4_pins: uart4-pins {
- pins = "PG12", "PG13", "PG14", "PG15";
- function = "uart4";
- };
- };
-
- uart0: serial at 7000000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x07000000 0x400>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART0>;
- resets = <&ccu RST_BUS_UART0>;
- status = "disabled";
- };
-
- uart1: serial at 7000400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x07000400 0x400>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART1>;
- resets = <&ccu RST_BUS_UART1>;
- status = "disabled";
- };
-
- uart2: serial at 7000800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x07000800 0x400>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART2>;
- resets = <&ccu RST_BUS_UART2>;
- status = "disabled";
- };
-
- uart3: serial at 7000c00 {
- compatible = "snps,dw-apb-uart";
- reg = <0x07000c00 0x400>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART3>;
- resets = <&ccu RST_BUS_UART3>;
- status = "disabled";
- };
-
- uart4: serial at 7001000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x07001000 0x400>;
- interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART4>;
- resets = <&ccu RST_BUS_UART4>;
- status = "disabled";
- };
-
- uart5: serial at 7001400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x07001400 0x400>;
- interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART5>;
- resets = <&ccu RST_BUS_UART5>;
- status = "disabled";
- };
-
- i2c0: i2c at 7002800 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x07002800 0x400>;
- interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C0>;
- resets = <&ccu RST_BUS_I2C0>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c1: i2c at 7002c00 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x07002c00 0x400>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C1>;
- resets = <&ccu RST_BUS_I2C1>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c2: i2c at 7003000 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x07003000 0x400>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C2>;
- resets = <&ccu RST_BUS_I2C2>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c3: i2c at 7003400 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x07003400 0x400>;
- interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C3>;
- resets = <&ccu RST_BUS_I2C3>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c4: i2c at 7003800 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x07003800 0x400>;
- interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C4>;
- resets = <&ccu RST_BUS_I2C4>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- r_wdt: watchdog at 8001000 {
- compatible = "allwinner,sun6i-a31-wdt";
- reg = <0x08001000 0x20>;
- interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&osc24M>;
- };
-
- prcm at 8001400 {
- compatible = "allwinner,sun9i-a80-prcm";
- reg = <0x08001400 0x200>;
- };
-
- apbs_rst: reset at 80014b0 {
- reg = <0x080014b0 0x4>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- #reset-cells = <1>;
- };
-
- nmi_intc: interrupt-controller at 80015a0 {
- compatible = "allwinner,sun9i-a80-nmi";
- interrupt-controller;
- #interrupt-cells = <2>;
- reg = <0x080015a0 0xc>;
- interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- r_ir: ir at 8002000 {
- compatible = "allwinner,sun6i-a31-ir";
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&r_ir_pins>;
- clocks = <&apbs_gates 1>, <&r_ir_clk>;
- clock-names = "apb", "ir";
- resets = <&apbs_rst 1>;
- reg = <0x08002000 0x40>;
- status = "disabled";
- };
-
- r_uart: serial at 8002800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x08002800 0x400>;
- interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&apbs_gates 4>;
- resets = <&apbs_rst 4>;
- status = "disabled";
- };
-
- r_pio: pinctrl at 8002c00 {
- compatible = "allwinner,sun9i-a80-r-pinctrl";
- reg = <0x08002c00 0x400>;
- interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apbs_gates 0>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- gpio-controller;
- interrupt-controller;
- #interrupt-cells = <3>;
- #gpio-cells = <3>;
-
- r_ir_pins: r-ir-pins {
- pins = "PL6";
- function = "s_cir_rx";
- };
-
- r_rsb_pins: r-rsb-pins {
- pins = "PN0", "PN1";
- function = "s_rsb";
- drive-strength = <20>;
- bias-pull-up;
- };
- };
-
- r_rsb: rsb at 8003400 {
- compatible = "allwinner,sun8i-a23-rsb";
- reg = <0x08003400 0x400>;
- interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apbs_gates 3>;
- clock-frequency = <3000000>;
- resets = <&apbs_rst 3>;
- pinctrl-names = "default";
- pinctrl-0 = <&r_rsb_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
- };
-};
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index d4c13f21027..e979ee4a2cc 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -499,6 +499,7 @@ config MACH_SUN9I
select SUN6I_PRCM
select SUNXI_GEN_SUN6I
select SUPPORT_SPL
+ imply OF_UPSTREAM
config MACH_SUN50I
bool "sun50i (Allwinner A64)"
diff --git a/configs/Cubieboard4_defconfig b/configs/Cubieboard4_defconfig
index 5b8428f2714..33937abfb22 100644
--- a/configs/Cubieboard4_defconfig
+++ b/configs/Cubieboard4_defconfig
@@ -1,6 +1,6 @@
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
-CONFIG_DEFAULT_DEVICE_TREE="sun9i-a80-cubieboard4"
+CONFIG_DEFAULT_DEVICE_TREE="allwinner/sun9i-a80-cubieboard4"
CONFIG_SPL=y
CONFIG_MACH_SUN9I=y
CONFIG_DRAM_CLK=672
diff --git a/configs/Merrii_A80_Optimus_defconfig b/configs/Merrii_A80_Optimus_defconfig
index c47dc59399d..1bfbeec1d02 100644
--- a/configs/Merrii_A80_Optimus_defconfig
+++ b/configs/Merrii_A80_Optimus_defconfig
@@ -1,6 +1,6 @@
CONFIG_ARM=y
CONFIG_ARCH_SUNXI=y
-CONFIG_DEFAULT_DEVICE_TREE="sun9i-a80-optimus"
+CONFIG_DEFAULT_DEVICE_TREE="allwinner/sun9i-a80-optimus"
CONFIG_SPL=y
CONFIG_MACH_SUN9I=y
CONFIG_DRAM_CLK=672
diff --git a/configs/Sunchip_CX-A99_defconfig b/configs/Sunchip_CX-A99_defconfig
index 0d78a13bd71..e25f5457f1a 100644
--- a/configs/Sunchip_CX-A99_defconfig
+++ b/configs/Sunchip_CX-A99_defconfig
@@ -8,3 +8,4 @@ CONFIG_DRAM_ZQ=3881915
CONFIG_DRAM_ODT_EN=y
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+# CONFIG_OF_UPSTREAM is not set
--
2.46.4
More information about the U-Boot
mailing list