[PATCH v2 3/3] sunxi: configs: enable power LEDs on 64-bit boards
Paul Kocialkowski
paulk at sys-base.io
Wed Apr 29 15:08:30 CEST 2026
Hi Andre,
On Wed 29 Apr 26, 11:28, Andre Przywara wrote:
> We recently gained a simple way to enable a power LED very early in the
> SPL boot, through simple Kconfig variables.
>
> Add those symbols to those boards' defconfigs where the DT indicates a
> default-on power LED. The number used is <port bank> * 32 + <pin no>,
> an active low setup means CONFIG_SPL_SUNXI_LED_STATUS_ACTIVE_HIGH must be
> undefined.
>
> This will light up the power LED very early in the (SPL) boot phase on
> those 64-bit boards.
>
> Signed-off-by: Andre Przywara <andre.przywara at arm.com>
Reviewed-by: Paul Kocialkowski <paulk at sys-base.io>
All the best,
Paul
> ---
> configs/anbernic_rg35xx_h700_defconfig | 2 ++
> configs/bananapi_m64_defconfig | 2 ++
> configs/beelink_gs1_defconfig | 2 ++
> configs/liontron-h-a133l_defconfig | 3 +++
> configs/nanopi_neo2_defconfig | 2 ++
> configs/nanopi_neo_plus2_defconfig | 2 ++
> configs/orangepi_3_defconfig | 2 ++
> configs/orangepi_lite2_defconfig | 2 ++
> configs/orangepi_pc2_defconfig | 2 ++
> configs/orangepi_prime_defconfig | 2 ++
> configs/orangepi_zero2_defconfig | 2 ++
> configs/orangepi_zero_plus2_defconfig | 2 ++
> configs/orangepi_zero_plus_defconfig | 2 ++
> configs/radxa-cubie-a5e_defconfig | 3 +++
> configs/tanix_tx1_defconfig | 2 ++
> 15 files changed, 32 insertions(+)
>
> diff --git a/configs/anbernic_rg35xx_h700_defconfig b/configs/anbernic_rg35xx_h700_defconfig
> index 2fa57cbecce..2abea94e979 100644
> --- a/configs/anbernic_rg35xx_h700_defconfig
> +++ b/configs/anbernic_rg35xx_h700_defconfig
> @@ -16,6 +16,8 @@ CONFIG_DRAM_SUNXI_PHY_ADDR_MAP_1=y
> CONFIG_MACH_SUN50I_H616=y
> CONFIG_SUNXI_DRAM_H616_LPDDR4=y
> CONFIG_R_I2C_ENABLE=y
> +CONFIG_SPL_SUNXI_LED_STATUS=y
> +CONFIG_SPL_SUNXI_LED_STATUS_GPIO=268
> CONFIG_SPL_I2C=y
> CONFIG_SPL_SYS_I2C_LEGACY=y
> CONFIG_SYS_I2C_MVTWSI=y
> diff --git a/configs/bananapi_m64_defconfig b/configs/bananapi_m64_defconfig
> index d957071cb13..3d1f5d27e5d 100644
> --- a/configs/bananapi_m64_defconfig
> +++ b/configs/bananapi_m64_defconfig
> @@ -4,6 +4,8 @@ CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-bananapi-m64"
> CONFIG_SPL=y
> CONFIG_MACH_SUN50I=y
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> +CONFIG_SPL_SUNXI_LED_STATUS=y
> +CONFIG_SPL_SUNXI_LED_STATUS_GPIO=120
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SUPPORT_EMMC_BOOT=y
> CONFIG_SUN8I_EMAC=y
> diff --git a/configs/beelink_gs1_defconfig b/configs/beelink_gs1_defconfig
> index de46d205453..ebac032915f 100644
> --- a/configs/beelink_gs1_defconfig
> +++ b/configs/beelink_gs1_defconfig
> @@ -5,6 +5,8 @@ CONFIG_SPL=y
> CONFIG_MACH_SUN50I_H6=y
> CONFIG_SUNXI_DRAM_H6_LPDDR3=y
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> +CONFIG_SPL_SUNXI_LED_STATUS=y
> +CONFIG_SPL_SUNXI_LED_STATUS_GPIO=356
> # CONFIG_PSCI_RESET is not set
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_LED=y
> diff --git a/configs/liontron-h-a133l_defconfig b/configs/liontron-h-a133l_defconfig
> index 831d5b56e3a..836e8d12ff0 100644
> --- a/configs/liontron-h-a133l_defconfig
> +++ b/configs/liontron-h-a133l_defconfig
> @@ -23,6 +23,9 @@ CONFIG_MACH_SUN50I_A133=y
> CONFIG_SUNXI_DRAM_A133_LPDDR4=y
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> CONFIG_R_I2C_ENABLE=y
> +CONFIG_SPL_SUNXI_LED_STATUS=y
> +CONFIG_SPL_SUNXI_LED_STATUS_GPIO=240
> +# CONFIG_SPL_SUNXI_LED_STATUS_ACTIVE_HIGH is not set
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SPL_I2C=y
> CONFIG_SPL_SYS_I2C_LEGACY=y
> diff --git a/configs/nanopi_neo2_defconfig b/configs/nanopi_neo2_defconfig
> index 6704a24a880..63fa6bac9ba 100644
> --- a/configs/nanopi_neo2_defconfig
> +++ b/configs/nanopi_neo2_defconfig
> @@ -6,6 +6,8 @@ CONFIG_SPL=y
> CONFIG_MACH_SUN50I_H5=y
> CONFIG_DRAM_ZQ=3881977
> # CONFIG_DRAM_ODT_EN is not set
> +CONFIG_SPL_SUNXI_LED_STATUS=y
> +CONFIG_SPL_SUNXI_LED_STATUS_GPIO=362
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SUN8I_EMAC=y
> CONFIG_USB_EHCI_HCD=y
> diff --git a/configs/nanopi_neo_plus2_defconfig b/configs/nanopi_neo_plus2_defconfig
> index e80e32a63d4..9d1b783476d 100644
> --- a/configs/nanopi_neo_plus2_defconfig
> +++ b/configs/nanopi_neo_plus2_defconfig
> @@ -7,6 +7,8 @@ CONFIG_MACH_SUN50I_H5=y
> CONFIG_DRAM_ZQ=3881977
> # CONFIG_DRAM_ODT_EN is not set
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> +CONFIG_SPL_SUNXI_LED_STATUS=y
> +CONFIG_SPL_SUNXI_LED_STATUS_GPIO=362
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SUN8I_EMAC=y
> CONFIG_USB_EHCI_HCD=y
> diff --git a/configs/orangepi_3_defconfig b/configs/orangepi_3_defconfig
> index 125137bc321..409fa705a06 100644
> --- a/configs/orangepi_3_defconfig
> +++ b/configs/orangepi_3_defconfig
> @@ -6,6 +6,8 @@ CONFIG_MACH_SUN50I_H6=y
> CONFIG_SUNXI_DRAM_H6_LPDDR3=y
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> CONFIG_BLUETOOTH_DT_DEVICE_FIXUP="brcm,bcm4345c5"
> +CONFIG_SPL_SUNXI_LED_STATUS=y
> +CONFIG_SPL_SUNXI_LED_STATUS_GPIO=356
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_PHY_SUN50I_USB3=y
> CONFIG_USB_XHCI_HCD=y
> diff --git a/configs/orangepi_lite2_defconfig b/configs/orangepi_lite2_defconfig
> index 577f7436c15..5d72d34eb9d 100644
> --- a/configs/orangepi_lite2_defconfig
> +++ b/configs/orangepi_lite2_defconfig
> @@ -4,6 +4,8 @@ CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-orangepi-lite2"
> CONFIG_SPL=y
> CONFIG_MACH_SUN50I_H6=y
> CONFIG_SUNXI_DRAM_H6_LPDDR3=y
> +CONFIG_SPL_SUNXI_LED_STATUS=y
> +CONFIG_SPL_SUNXI_LED_STATUS_GPIO=356
> # CONFIG_PSCI_RESET is not set
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_USB_EHCI_HCD=y
> diff --git a/configs/orangepi_pc2_defconfig b/configs/orangepi_pc2_defconfig
> index d856a25814b..464b34f4ec0 100644
> --- a/configs/orangepi_pc2_defconfig
> +++ b/configs/orangepi_pc2_defconfig
> @@ -6,6 +6,8 @@ CONFIG_SPL=y
> CONFIG_MACH_SUN50I_H5=y
> CONFIG_DRAM_ZQ=3881977
> CONFIG_SPL_SPI_SUNXI=y
> +CONFIG_SPL_SUNXI_LED_STATUS=y
> +CONFIG_SPL_SUNXI_LED_STATUS_GPIO=362
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SPL_I2C=y
> CONFIG_SPL_SYS_I2C_LEGACY=y
> diff --git a/configs/orangepi_prime_defconfig b/configs/orangepi_prime_defconfig
> index e93154cc0e9..e5e9009378c 100644
> --- a/configs/orangepi_prime_defconfig
> +++ b/configs/orangepi_prime_defconfig
> @@ -6,6 +6,8 @@ CONFIG_SPL=y
> CONFIG_MACH_SUN50I_H5=y
> CONFIG_DRAM_ZQ=3881977
> # CONFIG_DRAM_ODT_EN is not set
> +CONFIG_SPL_SUNXI_LED_STATUS=y
> +CONFIG_SPL_SUNXI_LED_STATUS_GPIO=362
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SUN8I_EMAC=y
> CONFIG_USB_EHCI_HCD=y
> diff --git a/configs/orangepi_zero2_defconfig b/configs/orangepi_zero2_defconfig
> index 831bfe66e25..b387b4795ad 100644
> --- a/configs/orangepi_zero2_defconfig
> +++ b/configs/orangepi_zero2_defconfig
> @@ -10,6 +10,8 @@ CONFIG_MACH_SUN50I_H616=y
> CONFIG_SUNXI_DRAM_H616_DDR3_1333=y
> CONFIG_R_I2C_ENABLE=y
> CONFIG_SPL_SPI_SUNXI=y
> +CONFIG_SPL_SUNXI_LED_STATUS=y
> +CONFIG_SPL_SUNXI_LED_STATUS_GPIO=76
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SPL_I2C=y
> CONFIG_SPL_SYS_I2C_LEGACY=y
> diff --git a/configs/orangepi_zero_plus2_defconfig b/configs/orangepi_zero_plus2_defconfig
> index c4d9800975c..9758ffd385e 100644
> --- a/configs/orangepi_zero_plus2_defconfig
> +++ b/configs/orangepi_zero_plus2_defconfig
> @@ -7,6 +7,8 @@ CONFIG_MACH_SUN50I_H5=y
> CONFIG_DRAM_ZQ=3881977
> # CONFIG_DRAM_ODT_EN is not set
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> +CONFIG_SPL_SUNXI_LED_STATUS=y
> +CONFIG_SPL_SUNXI_LED_STATUS_GPIO=362
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SUN8I_EMAC=y
> CONFIG_USB_EHCI_HCD=y
> diff --git a/configs/orangepi_zero_plus_defconfig b/configs/orangepi_zero_plus_defconfig
> index 4b6491dc846..bb159428a14 100644
> --- a/configs/orangepi_zero_plus_defconfig
> +++ b/configs/orangepi_zero_plus_defconfig
> @@ -6,6 +6,8 @@ CONFIG_SPL=y
> CONFIG_MACH_SUN50I_H5=y
> CONFIG_DRAM_ZQ=3881977
> # CONFIG_DRAM_ODT_EN is not set
> +CONFIG_SPL_SUNXI_LED_STATUS=y
> +CONFIG_SPL_SUNXI_LED_STATUS_GPIO=362
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SUN8I_EMAC=y
> CONFIG_USB_EHCI_HCD=y
> diff --git a/configs/radxa-cubie-a5e_defconfig b/configs/radxa-cubie-a5e_defconfig
> index 9d204ef5548..84bc4e3d4a9 100644
> --- a/configs/radxa-cubie-a5e_defconfig
> +++ b/configs/radxa-cubie-a5e_defconfig
> @@ -15,6 +15,9 @@ CONFIG_DRAM_SUNXI_TPR12=0x3533302f
> CONFIG_MACH_SUN55I_A523=y
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> CONFIG_R_I2C_ENABLE=y
> +CONFIG_SPL_SUNXI_LED_STATUS=y
> +CONFIG_SPL_SUNXI_LED_STATUS_GPIO=356
> +# CONFIG_SPL_SUNXI_LED_STATUS_ACTIVE_HIGH is not set
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SPL_I2C=y
> CONFIG_SPL_SYS_I2C_LEGACY=y
> diff --git a/configs/tanix_tx1_defconfig b/configs/tanix_tx1_defconfig
> index 1bd167ce0f6..03b18701859 100644
> --- a/configs/tanix_tx1_defconfig
> +++ b/configs/tanix_tx1_defconfig
> @@ -14,6 +14,8 @@ CONFIG_MACH_SUN50I_H616=y
> CONFIG_SUNXI_DRAM_H616_LPDDR3=y
> CONFIG_MMC_SUNXI_SLOT_EXTRA=2
> CONFIG_R_I2C_ENABLE=y
> +CONFIG_SPL_SUNXI_LED_STATUS=y
> +CONFIG_SPL_SUNXI_LED_STATUS_GPIO=231
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SPL_I2C=y
> CONFIG_SPL_SYS_I2C_LEGACY=y
> --
> 2.43.0
>
--
Paul Kocialkowski,
Independent contractor - sys-base - https://www.sys-base.io/
Free software developer - https://www.paulk.fr/
Expert in multimedia, graphics and embedded hardware support with Linux.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20260429/2298c383/attachment.sig>
More information about the U-Boot
mailing list