[PATCH v1 02/18] Kconfig: cmd: restyle
Johan Jonker
jbx6244 at gmail.com
Wed Jun 10 16:37:30 CEST 2026
Restyle all Kconfigs for "cmd":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
Signed-off-by: Johan Jonker <jbx6244 at gmail.com>
---
cmd/Kconfig | 74 +++++++++++++++++++++++++-------------------------
cmd/ti/Kconfig | 18 ++++++------
2 files changed, 46 insertions(+), 46 deletions(-)
diff --git a/cmd/Kconfig b/cmd/Kconfig
index c71c6824a196..6ca414e90743 100644
--- a/cmd/Kconfig
+++ b/cmd/Kconfig
@@ -881,12 +881,12 @@ config EEPROM_LAYOUT_VERSIONS
via the -l option.
config EEPROM_LAYOUT_HELP_STRING
- string "Tells user what layout names are supported"
- depends on EEPROM_LAYOUT_VERSIONS
- default "<not defined>"
- help
- Help printed with the LAYOUT VERSIONS part of the 'eeprom'
- command's help.
+ string "Tells user what layout names are supported"
+ depends on EEPROM_LAYOUT_VERSIONS
+ default "<not defined>"
+ help
+ Help printed with the LAYOUT VERSIONS part of the 'eeprom'
+ command's help.
config SYS_I2C_EEPROM_BUS
int "I2C bus of the EEPROM device."
@@ -967,14 +967,14 @@ config CMD_MEMORY
default y
help
Memory commands.
- md - memory display
- mm - memory modify (auto-incrementing address)
- nm - memory modify (constant address)
- mw - memory write (fill)
- cp - memory copy
- cmp - memory compare
- base - print or set address offset
- loop - initialize loop on address range
+ md - memory display
+ mm - memory modify (auto-incrementing address)
+ nm - memory modify (constant address)
+ mw - memory write (fill)
+ cp - memory copy
+ cmp - memory compare
+ base - print or set address offset
+ loop - initialize loop on address range
config CMD_MEM_SEARCH
bool "ms - Memory search"
@@ -1115,9 +1115,9 @@ config CMD_ARMFFA
help
Provides a test command for the FF-A support
supported options:
- - Listing the partition(s) info
- - Sending a data pattern to the specified partition
- - Displaying the arm_ffa device info
+ - Listing the partition(s) info
+ - Sending a data pattern to the specified partition
+ - Displaying the arm_ffa device info
config CMD_ARMFLASH
bool "armflash"
@@ -1214,9 +1214,9 @@ config CMD_FLASH
depends on FLASH_CFI_DRIVER || MTD_NOR_FLASH
help
NOR flash support.
- flinfo - print FLASH memory information
- erase - FLASH memory
- protect - enable or disable FLASH write protection
+ flinfo - print FLASH memory information
+ erase - FLASH memory
+ protect - enable or disable FLASH write protection
config CMD_FPGA
bool "fpga"
@@ -1548,7 +1548,7 @@ config CMD_OPTEE
bool "Enable OP-TEE commands"
depends on OPTEE
help
- OP-TEE commands support.
+ OP-TEE commands support.
config CMD_MTD
bool "mtd"
@@ -1606,7 +1606,7 @@ config CMD_MUX
bool "mux"
depends on MULTIPLEXER
help
- List, select, and deselect mux controllers on the fly.
+ List, select, and deselect mux controllers on the fly.
config CMD_NAND
bool "nand"
@@ -1814,7 +1814,7 @@ config CMD_UFS
depends on UFS
help
"This provides commands to initialise and configure universal flash
- subsystem devices"
+ subsystem devices"
config CMD_USB
bool "usb"
@@ -1936,7 +1936,7 @@ config CMD_SETEXPR
default y
help
Evaluate boolean and math expressions and store the result in an env
- variable.
+ variable.
Also supports loading the value at a memory location into a variable.
If CONFIG_REGEX is enabled, setexpr also supports a gsub function.
@@ -2642,9 +2642,9 @@ config CMD_PSTORE_ECC_SIZE
depends on CMD_PSTORE
default "0"
help
- if non-zero, the option enables ECC support and specifies ECC buffer
- size in bytes (1 is a special value, means 16 bytes ECC), should be
- identical to ramoops.ramoops_ecc parameter used by kernel
+ if non-zero, the option enables ECC support and specifies ECC buffer
+ size in bytes (1 is a special value, means 16 bytes ECC), should be
+ identical to ramoops.ramoops_ecc parameter used by kernel
endif
@@ -3156,15 +3156,15 @@ config CMD_AVB
help
Enables a "avb" command to perform verification of partitions using
Android Verified Boot 2.0 functionality. It includes such subcommands:
- avb init - initialize avb2 subsystem
- avb read_rb - read rollback index
- avb write_rb - write rollback index
- avb is_unlocked - check device lock state
- avb get_uuid - read and print uuid of a partition
- avb read_part - read data from partition
- avb read_part_hex - read data from partition and output to stdout
- avb write_part - write data to partition
- avb verify - run full verification chain
+ avb init - initialize avb2 subsystem
+ avb read_rb - read rollback index
+ avb write_rb - write rollback index
+ avb is_unlocked - check device lock state
+ avb get_uuid - read and print uuid of a partition
+ avb read_part - read data from partition
+ avb read_part_hex - read data from partition and output to stdout
+ avb write_part - write data to partition
+ avb verify - run full verification chain
config CMD_STACKPROTECTOR_TEST
bool "Test command for stack protector"
@@ -3194,7 +3194,7 @@ config CMD_UBI_RENAME
depends on CMD_UBI
help
Enable a "ubi" command to rename ubi volume:
- ubi rename <oldname> <newname>
+ ubi rename <oldname> <newname>
config CMD_UBIFS
tristate "Enable UBIFS - Unsorted block images filesystem commands"
diff --git a/cmd/ti/Kconfig b/cmd/ti/Kconfig
index 43fe9ef2f080..17cf867dd91d 100644
--- a/cmd/ti/Kconfig
+++ b/cmd/ti/Kconfig
@@ -4,24 +4,24 @@ config CMD_DDR3
bool "command for verifying DDR features"
depends on ARCH_KEYSTONE || DRA7XX
help
- Support for testing ddr3 on TI platforms. This command
- supports memory verification, memory comapre and ecc
- verification if supported.
+ Support for testing ddr3 on TI platforms. This command
+ supports memory verification, memory comapre and ecc
+ verification if supported.
config CMD_DDR4
bool "command for verifying DDRSS Inline ECC features"
depends on ARCH_K3
help
- Support for testing DDRSS on TI platforms. This command supports
- memory verification, memory compare and inline ECC verification
- if supported.
+ Support for testing DDRSS on TI platforms. This command supports
+ memory verification, memory compare and inline ECC verification
+ if supported.
config CMD_PD
bool "command for verifying power domains"
depends on TI_POWER_DOMAIN
help
- Debug command for K3 power domains. For this to work, the
- K3 power domain driver must be enabled for the u-boot; by
- default it is only enabled for SPL.
+ Debug command for K3 power domains. For this to work, the
+ K3 power domain driver must be enabled for the u-boot; by
+ default it is only enabled for SPL.
endmenu
--
2.39.5
More information about the U-Boot
mailing list