[U-Boot] [PATCH] video: Add new driver for Silicon Motion SM501/SM502 Part 1/2
Stefan Althoefer
stefan.althoefer at web.de
Thu Dec 4 22:10:07 CET 2008
[PATCH] video: Add new driver for Silicon Motion SM501/SM502
This patch adds a new driver for SM501/SM502. Compared to the
existing driver it allows dynamic selection of resolution
(environment: videomode).
The drive is based on Vincent Sanders and Ben Dooks' linux
kernel driver.
Use CONFIG_VIDEO_SM501NEW to enable the driver.
This has been tested on Janz emPC-A400. On this platform
the SM501 is connected via PCI.
The patch is against "latest" u-boot git-repository
Please (still) be patient if style of submission or patches are
offending.
Signed-off-by: Stefan Althoefer <stefan.althoefer at web.de>
----
diff -uprN u-boot-orig//drivers/video/sm501new.h u-boot/drivers/video/sm501new.h
--- u-boot-orig//drivers/video/sm501new.h 1970-01-01 01:00:00.000000000 +0100
+++ u-boot/drivers/video/sm501new.h 2008-12-02 18:28:42.000000000 +0100
@@ -0,0 +1,125 @@
+/* Large parts of this have been taken from the linux kernel source code
+ * with the following licencse:
+ *
+ * Copyright (c) 2006 Simtec Electronics
+ * Vincent Sanders <vince at simtec.co.uk>
+ * Ben Dooks <ben at simtec.co.uk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Framebuffer driver for the Silicon Motion SM501
+ */
+
+/* Ported to u-boot:
+ *
+ * Copyright (c) 2008 StefanAlthoefer (as at janz.de)
+ */
+
+/*
+ * Platform data definitions
+ */
+
+#define SM501FB_FLAG_USE_INIT_MODE (1<<0)
+#define SM501FB_FLAG_DISABLE_AT_EXIT (1<<1)
+#define SM501FB_FLAG_USE_HWCURSOR (1<<2)
+#define SM501FB_FLAG_USE_HWACCEL (1<<3)
+
+struct sm501_platdata_fbsub {
+ struct fb_videomode *def_mode;
+ unsigned int def_bpp;
+ unsigned long max_mem;
+ unsigned int flags;
+};
+
+enum sm501_fb_routing {
+ SM501_FB_OWN = 0, /* CRT=>CRT, Panel=>Panel */
+ SM501_FB_CRT_PANEL = 1, /* Panel=>CRT, Panel=>Panel */
+};
+
+/* sm501_platdata_fb flag field bit definitions */
+
+#define SM501_FBPD_SWAP_FB_ENDIAN (1<<0) /* need to endian swap */
+
+/* sm501_platdata_fb
+ *
+ * configuration data for the framebuffer driver
+*/
+
+struct sm501_platdata_fb {
+ enum sm501_fb_routing fb_route;
+ unsigned int flags;
+ struct sm501_platdata_fbsub *fb_crt;
+ struct sm501_platdata_fbsub *fb_pnl;
+};
+
+/* gpio i2c */
+
+struct sm501_platdata_gpio_i2c {
+ unsigned int pin_sda;
+ unsigned int pin_scl;
+};
+
+/* sm501_initdata
+ *
+ * use for initialising values that may not have been setup
+ * before the driver is loaded.
+*/
+
+struct sm501_reg_init {
+ unsigned long set;
+ unsigned long mask;
+};
+
+#define SM501_USE_USB_HOST (1<<0)
+#define SM501_USE_USB_SLAVE (1<<1)
+#define SM501_USE_SSP0 (1<<2)
+#define SM501_USE_SSP1 (1<<3)
+#define SM501_USE_UART0 (1<<4)
+#define SM501_USE_UART1 (1<<5)
+#define SM501_USE_FBACCEL (1<<6)
+#define SM501_USE_AC97 (1<<7)
+#define SM501_USE_I2S (1<<8)
+
+#define SM501_USE_ALL (0xffffffff)
+
+struct sm501_initdata {
+ struct sm501_reg_init gpio_low;
+ struct sm501_reg_init gpio_high;
+ struct sm501_reg_init misc_timing;
+ struct sm501_reg_init misc_control;
+
+ unsigned long devices;
+ unsigned long mclk; /* non-zero to modify */
+ unsigned long m1xclk; /* non-zero to modify */
+};
+
+/* sm501_init_gpio
+ *
+ * default gpio settings
+*/
+
+struct sm501_init_gpio {
+ struct sm501_reg_init gpio_data_low;
+ struct sm501_reg_init gpio_data_high;
+ struct sm501_reg_init gpio_ddr_low;
+ struct sm501_reg_init gpio_ddr_high;
+};
+
+/* sm501_platdata
+ *
+ * This is passed with the platform device to allow the board
+ * to control the behaviour of the SM501 driver(s) which attach
+ * to the device.
+ *
+*/
+
+struct sm501_platdata {
+ struct sm501_initdata *init;
+ struct sm501_init_gpio *init_gpiop;
+ struct sm501_platdata_fb *fb;
+
+ struct sm501_platdata_gpio_i2c *gpio_i2c;
+ unsigned int gpio_i2c_nr;
+};
diff -uprN u-boot-orig//drivers/video/sm501new-regs.h u-boot/drivers/video/sm501new-regs.h
--- u-boot-orig//drivers/video/sm501new-regs.h 1970-01-01 01:00:00.000000000 +0100
+++ u-boot/drivers/video/sm501new-regs.h 2008-12-02 18:28:42.000000000 +0100
@@ -0,0 +1,365 @@
+/* sm501-regs.h
+ *
+ * Copyright 2006 Simtec Electronics
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Silicon Motion SM501 register definitions
+*/
+
+/* System Configuration area */
+/* System config base */
+#define SM501_SYS_CONFIG (0x000000)
+
+/* config 1 */
+#define SM501_SYSTEM_CONTROL (0x000000)
+#define SM501_MISC_CONTROL (0x000004)
+
+#define SM501_MISC_BUS_SH (0x0)
+#define SM501_MISC_BUS_PCI (0x1)
+#define SM501_MISC_BUS_XSCALE (0x2)
+#define SM501_MISC_BUS_NEC (0x6)
+#define SM501_MISC_BUS_MASK (0x7)
+
+#define SM501_MISC_VR_62MB (1<<3)
+#define SM501_MISC_CDR_RESET (1<<7)
+#define SM501_MISC_USB_LB (1<<8)
+#define SM501_MISC_USB_SLAVE (1<<9)
+#define SM501_MISC_BL_1 (1<<10)
+#define SM501_MISC_MC (1<<11)
+#define SM501_MISC_DAC_POWER (1<<12)
+#define SM501_MISC_IRQ_INVERT (1<<16)
+#define SM501_MISC_SH (1<<17)
+
+#define SM501_MISC_HOLD_EMPTY (0<<18)
+#define SM501_MISC_HOLD_8 (1<<18)
+#define SM501_MISC_HOLD_16 (2<<18)
+#define SM501_MISC_HOLD_24 (3<<18)
+#define SM501_MISC_HOLD_32 (4<<18)
+#define SM501_MISC_HOLD_MASK (7<<18)
+
+#define SM501_MISC_FREQ_12 (1<<24)
+#define SM501_MISC_PNL_24BIT (1<<25)
+#define SM501_MISC_8051_LE (1<<26)
+
+
+
+#define SM501_GPIO31_0_CONTROL (0x000008)
+#define SM501_GPIO63_32_CONTROL (0x00000C)
+#define SM501_DRAM_CONTROL (0x000010)
+
+/* command list */
+#define SM501_ARBTRTN_CONTROL (0x000014)
+
+/* command list */
+#define SM501_COMMAND_LIST_STATUS (0x000024)
+
+/* interrupt debug */
+#define SM501_RAW_IRQ_STATUS (0x000028)
+#define SM501_RAW_IRQ_CLEAR (0x000028)
+#define SM501_IRQ_STATUS (0x00002C)
+#define SM501_IRQ_MASK (0x000030)
+#define SM501_DEBUG_CONTROL (0x000034)
+
+/* power management */
+#define SM501_POWERMODE_P2X_SRC (1<<29)
+#define SM501_POWERMODE_V2X_SRC (1<<20)
+#define SM501_POWERMODE_M_SRC (1<<12)
+#define SM501_POWERMODE_M1_SRC (1<<4)
+
+#define SM501_CURRENT_GATE (0x000038)
+#define SM501_CURRENT_CLOCK (0x00003C)
+#define SM501_POWER_MODE_0_GATE (0x000040)
+#define SM501_POWER_MODE_0_CLOCK (0x000044)
+#define SM501_POWER_MODE_1_GATE (0x000048)
+#define SM501_POWER_MODE_1_CLOCK (0x00004C)
+#define SM501_SLEEP_MODE_GATE (0x000050)
+#define SM501_POWER_MODE_CONTROL (0x000054)
+
+/* power gates for units within the 501 */
+#define SM501_GATE_HOST (0)
+#define SM501_GATE_MEMORY (1)
+#define SM501_GATE_DISPLAY (2)
+#define SM501_GATE_2D_ENGINE (3)
+#define SM501_GATE_CSC (4)
+#define SM501_GATE_ZVPORT (5)
+#define SM501_GATE_GPIO (6)
+#define SM501_GATE_UART0 (7)
+#define SM501_GATE_UART1 (8)
+#define SM501_GATE_SSP (10)
+#define SM501_GATE_USB_HOST (11)
+#define SM501_GATE_USB_GADGET (12)
+#define SM501_GATE_UCONTROLLER (17)
+#define SM501_GATE_AC97 (18)
+
+/* panel clock */
+#define SM501_CLOCK_P2XCLK (24)
+/* crt clock */
+#define SM501_CLOCK_V2XCLK (16)
+/* main clock */
+#define SM501_CLOCK_MCLK (8)
+/* SDRAM controller clock */
+#define SM501_CLOCK_M1XCLK (0)
+
+/* config 2 */
+#define SM501_PCI_MASTER_BASE (0x000058)
+#define SM501_ENDIAN_CONTROL (0x00005C)
+#define SM501_DEVICEID (0x000060)
+/* 0x050100A0 */
+
+#define SM501_DEVICEID_SM501 (0x05010000)
+#define SM501_DEVICEID_IDMASK (0xffff0000)
+
+#define SM501_PLLCLOCK_COUNT (0x000064)
+#define SM501_MISC_TIMING (0x000068)
+#define SM501_CURRENT_SDRAM_CLOCK (0x00006C)
+
+/* GPIO base */
+#define SM501_GPIO (0x010000)
+#define SM501_GPIO_DATA_LOW (0x00)
+#define SM501_GPIO_DATA_HIGH (0x04)
+#define SM501_GPIO_DDR_LOW (0x08)
+#define SM501_GPIO_DDR_HIGH (0x0C)
+#define SM501_GPIO_IRQ_SETUP (0x10)
+#define SM501_GPIO_IRQ_STATUS (0x14)
+#define SM501_GPIO_IRQ_RESET (0x14)
+
+/* I2C controller base */
+#define SM501_I2C (0x010040)
+#define SM501_I2C_BYTE_COUNT (0x00)
+#define SM501_I2C_CONTROL (0x01)
+#define SM501_I2C_STATUS (0x02)
+#define SM501_I2C_RESET (0x02)
+#define SM501_I2C_SLAVE_ADDRESS (0x03)
+#define SM501_I2C_DATA (0x04)
+
+/* SSP base */
+#define SM501_SSP (0x020000)
+
+/* Uart 0 base */
+#define SM501_UART0 (0x030000)
+
+/* Uart 1 base */
+#define SM501_UART1 (0x030020)
+
+/* USB host port base */
+#define SM501_USB_HOST (0x040000)
+
+/* USB slave/gadget base */
+#define SM501_USB_GADGET (0x060000)
+
+/* USB slave/gadget data port base */
+#define SM501_USB_GADGET_DATA (0x070000)
+
+/* Display contoller/video engine base */
+#define SM501_DC (0x080000)
+
+/* common defines for the SM501 address registers */
+#define SM501_ADDR_FLIP (1<<31)
+#define SM501_ADDR_EXT (1<<27)
+#define SM501_ADDR_CS1 (1<<26)
+#define SM501_ADDR_MASK (0x3f << 26)
+
+#define SM501_FIFO_MASK (0x3 << 16)
+#define SM501_FIFO_1 (0x0 << 16)
+#define SM501_FIFO_3 (0x1 << 16)
+#define SM501_FIFO_7 (0x2 << 16)
+#define SM501_FIFO_11 (0x3 << 16)
+
+/* common registers for panel and the crt */
+#define SM501_OFF_DC_H_TOT (0x000)
+#define SM501_OFF_DC_V_TOT (0x008)
+#define SM501_OFF_DC_H_SYNC (0x004)
+#define SM501_OFF_DC_V_SYNC (0x00C)
+
+#define SM501_DC_PANEL_CONTROL (0x000)
+
+#define SM501_DC_PANEL_CONTROL_FPEN (1<<27)
+#define SM501_DC_PANEL_CONTROL_BIAS (1<<26)
+#define SM501_DC_PANEL_CONTROL_DATA (1<<25)
+#define SM501_DC_PANEL_CONTROL_VDD (1<<24)
+#define SM501_DC_PANEL_CONTROL_DP (1<<23)
+
+#define SM501_DC_PANEL_CONTROL_TFT_888 (0<<21)
+#define SM501_DC_PANEL_CONTROL_TFT_333 (1<<21)
+#define SM501_DC_PANEL_CONTROL_TFT_444 (2<<21)
+
+#define SM501_DC_PANEL_CONTROL_DE (1<<20)
+
+#define SM501_DC_PANEL_CONTROL_LCD_TFT (0<<18)
+#define SM501_DC_PANEL_CONTROL_LCD_STN8 (1<<18)
+#define SM501_DC_PANEL_CONTROL_LCD_STN12 (2<<18)
+
+#define SM501_DC_PANEL_CONTROL_CP (1<<14)
+#define SM501_DC_PANEL_CONTROL_VSP (1<<13)
+#define SM501_DC_PANEL_CONTROL_HSP (1<<12)
+#define SM501_DC_PANEL_CONTROL_CK (1<<9)
+#define SM501_DC_PANEL_CONTROL_TE (1<<8)
+#define SM501_DC_PANEL_CONTROL_VPD (1<<7)
+#define SM501_DC_PANEL_CONTROL_VP (1<<6)
+#define SM501_DC_PANEL_CONTROL_HPD (1<<5)
+#define SM501_DC_PANEL_CONTROL_HP (1<<4)
+#define SM501_DC_PANEL_CONTROL_GAMMA (1<<3)
+#define SM501_DC_PANEL_CONTROL_EN (1<<2)
+
+#define SM501_DC_PANEL_CONTROL_8BPP (0<<0)
+#define SM501_DC_PANEL_CONTROL_16BPP (1<<0)
+#define SM501_DC_PANEL_CONTROL_32BPP (2<<0)
+
+
+#define SM501_DC_PANEL_PANNING_CONTROL (0x004)
+#define SM501_DC_PANEL_COLOR_KEY (0x008)
+#define SM501_DC_PANEL_FB_ADDR (0x00C)
+#define SM501_DC_PANEL_FB_OFFSET (0x010)
+#define SM501_DC_PANEL_FB_WIDTH (0x014)
+#define SM501_DC_PANEL_FB_HEIGHT (0x018)
+#define SM501_DC_PANEL_TL_LOC (0x01C)
+#define SM501_DC_PANEL_BR_LOC (0x020)
+#define SM501_DC_PANEL_H_TOT (0x024)
+#define SM501_DC_PANEL_H_SYNC (0x028)
+#define SM501_DC_PANEL_V_TOT (0x02C)
+#define SM501_DC_PANEL_V_SYNC (0x030)
+#define SM501_DC_PANEL_CUR_LINE (0x034)
+
+#define SM501_DC_VIDEO_CONTROL (0x040)
+#define SM501_DC_VIDEO_FB0_ADDR (0x044)
+#define SM501_DC_VIDEO_FB_WIDTH (0x048)
+#define SM501_DC_VIDEO_FB0_LAST_ADDR (0x04C)
+#define SM501_DC_VIDEO_TL_LOC (0x050)
+#define SM501_DC_VIDEO_BR_LOC (0x054)
+#define SM501_DC_VIDEO_SCALE (0x058)
+#define SM501_DC_VIDEO_INIT_SCALE (0x05C)
+#define SM501_DC_VIDEO_YUV_CONSTANTS (0x060)
+#define SM501_DC_VIDEO_FB1_ADDR (0x064)
+#define SM501_DC_VIDEO_FB1_LAST_ADDR (0x068)
+
+#define SM501_DC_VIDEO_ALPHA_CONTROL (0x080)
+#define SM501_DC_VIDEO_ALPHA_FB_ADDR (0x084)
+#define SM501_DC_VIDEO_ALPHA_FB_OFFSET (0x088)
+#define SM501_DC_VIDEO_ALPHA_FB_LAST_ADDR (0x08C)
+#define SM501_DC_VIDEO_ALPHA_TL_LOC (0x090)
+#define SM501_DC_VIDEO_ALPHA_BR_LOC (0x094)
+#define SM501_DC_VIDEO_ALPHA_SCALE (0x098)
+#define SM501_DC_VIDEO_ALPHA_INIT_SCALE (0x09C)
+#define SM501_DC_VIDEO_ALPHA_CHROMA_KEY (0x0A0)
+#define SM501_DC_VIDEO_ALPHA_COLOR_LOOKUP (0x0A4)
+
+#define SM501_DC_PANEL_HWC_BASE (0x0F0)
+#define SM501_DC_PANEL_HWC_ADDR (0x0F0)
+#define SM501_DC_PANEL_HWC_LOC (0x0F4)
+#define SM501_DC_PANEL_HWC_COLOR_1_2 (0x0F8)
+#define SM501_DC_PANEL_HWC_COLOR_3 (0x0FC)
+
+#define SM501_HWC_EN (1<<31)
+
+#define SM501_OFF_HWC_ADDR (0x00)
+#define SM501_OFF_HWC_LOC (0x04)
+#define SM501_OFF_HWC_COLOR_1_2 (0x08)
+#define SM501_OFF_HWC_COLOR_3 (0x0C)
+
+#define SM501_DC_ALPHA_CONTROL (0x100)
+#define SM501_DC_ALPHA_FB_ADDR (0x104)
+#define SM501_DC_ALPHA_FB_OFFSET (0x108)
+#define SM501_DC_ALPHA_TL_LOC (0x10C)
+#define SM501_DC_ALPHA_BR_LOC (0x110)
+#define SM501_DC_ALPHA_CHROMA_KEY (0x114)
+#define SM501_DC_ALPHA_COLOR_LOOKUP (0x118)
+
+#define SM501_DC_CRT_CONTROL (0x200)
+
+#define SM501_DC_CRT_CONTROL_TVP (1<<15)
+#define SM501_DC_CRT_CONTROL_CP (1<<14)
+#define SM501_DC_CRT_CONTROL_VSP (1<<13)
+#define SM501_DC_CRT_CONTROL_HSP (1<<12)
+#define SM501_DC_CRT_CONTROL_VS (1<<11)
+#define SM501_DC_CRT_CONTROL_BLANK (1<<10)
+#define SM501_DC_CRT_CONTROL_SEL (1<<9)
+#define SM501_DC_CRT_CONTROL_TE (1<<8)
+#define SM501_DC_CRT_CONTROL_PIXEL_MASK (0xF << 4)
+#define SM501_DC_CRT_CONTROL_GAMMA (1<<3)
+#define SM501_DC_CRT_CONTROL_ENABLE (1<<2)
+
+#define SM501_DC_CRT_CONTROL_8BPP (0<<0)
+#define SM501_DC_CRT_CONTROL_16BPP (1<<0)
+#define SM501_DC_CRT_CONTROL_32BPP (2<<0)
+
+#define SM501_DC_CRT_FB_ADDR (0x204)
+#define SM501_DC_CRT_FB_OFFSET (0x208)
+#define SM501_DC_CRT_H_TOT (0x20C)
+#define SM501_DC_CRT_H_SYNC (0x210)
+#define SM501_DC_CRT_V_TOT (0x214)
+#define SM501_DC_CRT_V_SYNC (0x218)
+#define SM501_DC_CRT_SIGNATURE_ANALYZER (0x21C)
+#define SM501_DC_CRT_CUR_LINE (0x220)
+#define SM501_DC_CRT_MONITOR_DETECT (0x224)
+
+#define SM501_DC_CRT_HWC_BASE (0x230)
+#define SM501_DC_CRT_HWC_ADDR (0x230)
+#define SM501_DC_CRT_HWC_LOC (0x234)
+#define SM501_DC_CRT_HWC_COLOR_1_2 (0x238)
+#define SM501_DC_CRT_HWC_COLOR_3 (0x23C)
+
+#define SM501_DC_PANEL_PALETTE (0x400)
+
+#define SM501_DC_VIDEO_PALETTE (0x800)
+
+#define SM501_DC_CRT_PALETTE (0xC00)
+
+/* Zoom Video port base */
+#define SM501_ZVPORT (0x090000)
+
+/* AC97/I2S base */
+#define SM501_AC97 (0x0A0000)
+
+/* 8051 micro controller base */
+#define SM501_UCONTROLLER (0x0B0000)
+
+/* 8051 micro controller SRAM base */
+#define SM501_UCONTROLLER_SRAM (0x0C0000)
+
+/* DMA base */
+#define SM501_DMA (0x0D0000)
+
+/* 2d engine base */
+#define SM501_2D_ENGINE (0x100000)
+#define SM501_2D_SOURCE (0x00)
+#define SM501_2D_DESTINATION (0x04)
+#define SM501_2D_DIMENSION (0x08)
+#define SM501_2D_CONTROL (0x0C)
+#define SM501_2D_PITCH (0x10)
+#define SM501_2D_FOREGROUND (0x14)
+#define SM501_2D_BACKGROUND (0x18)
+#define SM501_2D_STRETCH (0x1C)
+#define SM501_2D_COLOR_COMPARE (0x20)
+#define SM501_2D_COLOR_COMPARE_MASK (0x24)
+#define SM501_2D_MASK (0x28)
+#define SM501_2D_CLIP_TL (0x2C)
+#define SM501_2D_CLIP_BR (0x30)
+#define SM501_2D_MONO_PATTERN_LOW (0x34)
+#define SM501_2D_MONO_PATTERN_HIGH (0x38)
+#define SM501_2D_WINDOW_WIDTH (0x3C)
+#define SM501_2D_SOURCE_BASE (0x40)
+#define SM501_2D_DESTINATION_BASE (0x44)
+#define SM501_2D_ALPHA (0x48)
+#define SM501_2D_WRAP (0x4C)
+#define SM501_2D_STATUS (0x50)
+
+#define SM501_CSC_Y_SOURCE_BASE (0xC8)
+#define SM501_CSC_CONSTANTS (0xCC)
+#define SM501_CSC_Y_SOURCE_X (0xD0)
+#define SM501_CSC_Y_SOURCE_Y (0xD4)
+#define SM501_CSC_U_SOURCE_BASE (0xD8)
+#define SM501_CSC_V_SOURCE_BASE (0xDC)
+#define SM501_CSC_SOURCE_DIMENSION (0xE0)
+#define SM501_CSC_SOURCE_PITCH (0xE4)
+#define SM501_CSC_DESTINATION (0xE8)
+#define SM501_CSC_DESTINATION_DIMENSION (0xEC)
+#define SM501_CSC_DESTINATION_PITCH (0xF0)
+#define SM501_CSC_SCALE_FACTOR (0xF4)
+#define SM501_CSC_DESTINATION_BASE (0xF8)
+#define SM501_CSC_CONTROL (0xFC)
+
+/* 2d engine data port base */
+#define SM501_2D_ENGINE_DATA (0x110000)
More information about the U-Boot
mailing list