[U-Boot] [PATCH 08/15 v6] OMAP3: Add I2C support
Dirk Behme
dirk.behme at googlemail.com
Sun Dec 14 09:47:18 CET 2008
Add I2C support.
Signed-off-by: Dirk Behme <dirk.behme at googlemail.com>
---
drivers/i2c/Makefile | 1
drivers/i2c/omap24xx_i2c.c | 23 +++++++
include/asm-arm/arch-omap3/i2c.h | 128 +++++++++++++++++++++++++++++++++++++++
3 files changed, 152 insertions(+)
Index: u-boot-main/drivers/i2c/Makefile
===================================================================
--- u-boot-main.orig/drivers/i2c/Makefile
+++ u-boot-main/drivers/i2c/Makefile
@@ -29,6 +29,7 @@ COBJS-$(CONFIG_FSL_I2C) += fsl_i2c.o
COBJS-$(CONFIG_I2C_MXC) += mxc_i2c.o
COBJS-$(CONFIG_DRIVER_OMAP1510_I2C) += omap1510_i2c.o
COBJS-$(CONFIG_DRIVER_OMAP24XX_I2C) += omap24xx_i2c.o
+COBJS-$(CONFIG_DRIVER_OMAP34XX_I2C) += omap24xx_i2c.o
COBJS-$(CONFIG_SOFT_I2C) += soft_i2c.o
COBJS-$(CONFIG_TSI108_I2C) += tsi108_i2c.o
Index: u-boot-main/drivers/i2c/omap24xx_i2c.c
===================================================================
--- u-boot-main.orig/drivers/i2c/omap24xx_i2c.c
+++ u-boot-main/drivers/i2c/omap24xx_i2c.c
@@ -109,7 +109,11 @@ static int i2c_read_byte (u8 devaddr, u8
status = wait_for_pin ();
if (status & I2C_STAT_RRDY) {
+#if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX)
+ *value = readb (I2C_DATA);
+#else
*value = readw (I2C_DATA);
+#endif
udelay (20000);
} else {
i2c_error = 1;
@@ -150,8 +154,23 @@ static int i2c_write_byte (u8 devaddr, u
status = wait_for_pin ();
if (status & I2C_STAT_XRDY) {
+#if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX)
+ /* send out 1 byte */
+ writeb (regoffset, I2C_DATA);
+ writew (I2C_STAT_XRDY, I2C_STAT);
+
+ status = wait_for_pin ();
+ if ((status & I2C_STAT_XRDY)) {
+ /* send out next 1 byte */
+ writeb (value, I2C_DATA);
+ writew (I2C_STAT_XRDY, I2C_STAT);
+ } else {
+ i2c_error = 1;
+ }
+#else
/* send out two bytes */
writew ((value << 8) + regoffset, I2C_DATA);
+#endif
/* must have enough delay to allow BB bit to go low */
udelay (50000);
if (readw (I2C_STAT) & I2C_STAT_NACK) {
@@ -188,7 +207,11 @@ static void flush_fifo(void)
while(1){
stat = readw(I2C_STAT);
if(stat == I2C_STAT_RRDY){
+#if defined(CONFIG_OMAP243X) || defined(CONFIG_OMAP34XX)
+ readb(I2C_DATA);
+#else
readw(I2C_DATA);
+#endif
writew(I2C_STAT_RRDY,I2C_STAT);
udelay(1000);
}else
Index: u-boot-main/include/asm-arm/arch-omap3/i2c.h
===================================================================
--- /dev/null
+++ u-boot-main/include/asm-arm/arch-omap3/i2c.h
@@ -0,0 +1,128 @@
+/*
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+#ifndef _I2C_H_
+#define _I2C_H_
+
+#define I2C_DEFAULT_BASE I2C_BASE1
+
+#define I2C_REV (I2C_DEFAULT_BASE + 0x00)
+#define I2C_IE (I2C_DEFAULT_BASE + 0x04)
+#define I2C_STAT (I2C_DEFAULT_BASE + 0x08)
+#define I2C_IV (I2C_DEFAULT_BASE + 0x0c)
+#define I2C_BUF (I2C_DEFAULT_BASE + 0x14)
+#define I2C_CNT (I2C_DEFAULT_BASE + 0x18)
+#define I2C_DATA (I2C_DEFAULT_BASE + 0x1c)
+#define I2C_SYSC (I2C_DEFAULT_BASE + 0x20)
+#define I2C_CON (I2C_DEFAULT_BASE + 0x24)
+#define I2C_OA (I2C_DEFAULT_BASE + 0x28)
+#define I2C_SA (I2C_DEFAULT_BASE + 0x2c)
+#define I2C_PSC (I2C_DEFAULT_BASE + 0x30)
+#define I2C_SCLL (I2C_DEFAULT_BASE + 0x34)
+#define I2C_SCLH (I2C_DEFAULT_BASE + 0x38)
+#define I2C_SYSTEST (I2C_DEFAULT_BASE + 0x3c)
+
+/* I2C masks */
+
+/* I2C Interrupt Enable Register (I2C_IE): */
+#define I2C_IE_GC_IE (1 << 5)
+#define I2C_IE_XRDY_IE (1 << 4) /* Transmit data ready interrupt enable */
+#define I2C_IE_RRDY_IE (1 << 3) /* Receive data ready interrupt enable */
+#define I2C_IE_ARDY_IE (1 << 2) /* Register access ready interrupt enable */
+#define I2C_IE_NACK_IE (1 << 1) /* No acknowledgment interrupt enable */
+#define I2C_IE_AL_IE (1 << 0) /* Arbitration lost interrupt enable */
+
+/* I2C Status Register (I2C_STAT): */
+
+#define I2C_STAT_SBD (1 << 15) /* Single byte data */
+#define I2C_STAT_BB (1 << 12) /* Bus busy */
+#define I2C_STAT_ROVR (1 << 11) /* Receive overrun */
+#define I2C_STAT_XUDF (1 << 10) /* Transmit underflow */
+#define I2C_STAT_AAS (1 << 9) /* Address as slave */
+#define I2C_STAT_GC (1 << 5)
+#define I2C_STAT_XRDY (1 << 4) /* Transmit data ready */
+#define I2C_STAT_RRDY (1 << 3) /* Receive data ready */
+#define I2C_STAT_ARDY (1 << 2) /* Register access ready */
+#define I2C_STAT_NACK (1 << 1) /* No acknowledgment interrupt enable */
+#define I2C_STAT_AL (1 << 0) /* Arbitration lost interrupt enable */
+
+/* I2C Interrupt Code Register (I2C_INTCODE): */
+
+#define I2C_INTCODE_MASK 7
+#define I2C_INTCODE_NONE 0
+#define I2C_INTCODE_AL 1 /* Arbitration lost */
+#define I2C_INTCODE_NAK 2 /* No acknowledgement/general call */
+#define I2C_INTCODE_ARDY 3 /* Register access ready */
+#define I2C_INTCODE_RRDY 4 /* Rcv data ready */
+#define I2C_INTCODE_XRDY 5 /* Xmit data ready */
+
+/* I2C Buffer Configuration Register (I2C_BUF): */
+
+#define I2C_BUF_RDMA_EN (1 << 15) /* Receive DMA channel enable */
+#define I2C_BUF_XDMA_EN (1 << 7) /* Transmit DMA channel enable */
+
+/* I2C Configuration Register (I2C_CON): */
+
+#define I2C_CON_EN (1 << 15) /* I2C module enable */
+#define I2C_CON_BE (1 << 14) /* Big endian mode */
+#define I2C_CON_STB (1 << 11) /* Start byte mode (master mode only) */
+#define I2C_CON_MST (1 << 10) /* Master/slave mode */
+#define I2C_CON_TRX (1 << 9) /* Transmitter/receiver mode */
+ /* (master mode only) */
+#define I2C_CON_XA (1 << 8) /* Expand address */
+#define I2C_CON_STP (1 << 1) /* Stop condition (master mode only) */
+#define I2C_CON_STT (1 << 0) /* Start condition (master mode only) */
+
+/* I2C System Test Register (I2C_SYSTEST): */
+
+#define I2C_SYSTEST_ST_EN (1 << 15) /* System test enable */
+#define I2C_SYSTEST_FREE (1 << 14) /* Free running mode, on brkpoint) */
+#define I2C_SYSTEST_TMODE_MASK (3 << 12) /* Test mode select */
+#define I2C_SYSTEST_TMODE_SHIFT (12) /* Test mode select */
+#define I2C_SYSTEST_SCL_I (1 << 3) /* SCL line sense input value */
+#define I2C_SYSTEST_SCL_O (1 << 2) /* SCL line drive output value */
+#define I2C_SYSTEST_SDA_I (1 << 1) /* SDA line sense input value */
+#define I2C_SYSTEST_SDA_O (1 << 0) /* SDA line drive output value */
+
+#define I2C_SCLL_SCLL 0
+#define I2C_SCLL_SCLL_M 0xFF
+#define I2C_SCLL_HSSCLL 8
+#define I2C_SCLH_HSSCLL_M 0xFF
+#define I2C_SCLH_SCLH 0
+#define I2C_SCLH_SCLH_M 0xFF
+#define I2C_SCLH_HSSCLH 8
+#define I2C_SCLH_HSSCLH_M 0xFF
+
+#define OMAP_I2C_STANDARD 100
+#define OMAP_I2C_FAST_MODE 400
+#define OMAP_I2C_HIGH_SPEED 3400
+
+#define SYSTEM_CLOCK_12 12000
+#define SYSTEM_CLOCK_13 13000
+#define SYSTEM_CLOCK_192 19200
+#define SYSTEM_CLOCK_96 96000
+
+#define I2C_IP_CLK SYSTEM_CLOCK_96
+#define I2C_PSC_MAX 0x0f
+#define I2C_PSC_MIN 0x00
+
+#endif /* _I2C_H_ */
More information about the U-Boot
mailing list