[U-Boot] [PATCH] TI: OMAP3: Remove SZ_xx references
s-paulraj at ti.com
s-paulraj at ti.com
Wed Sep 9 16:55:54 CEST 2009
From: Sandeep Paulraj <s-paulraj at ti.com>
This patch removes dependency on the sizes.h header file
and removes all references to SZ_xx.
Signed-off-by: Sandeep Paulraj <s-paulraj at ti.com>
---
Compiled all OMAP3 based boards.
cpu/arm_cortexa8/omap3/mem.c | 6 +++---
cpu/arm_cortexa8/omap3/sys_info.c | 2 +-
include/configs/devkit8000.h | 15 +++++++--------
include/configs/omap3_beagle.h | 15 +++++++--------
include/configs/omap3_evm.h | 15 +++++++--------
include/configs/omap3_overo.h | 15 +++++++--------
include/configs/omap3_pandora.h | 15 +++++++--------
include/configs/omap3_zoom1.h | 15 +++++++--------
include/configs/omap3_zoom2.h | 15 +++++++--------
9 files changed, 53 insertions(+), 60 deletions(-)
diff --git a/cpu/arm_cortexa8/omap3/mem.c b/cpu/arm_cortexa8/omap3/mem.c
index 079c848..a269a17 100644
--- a/cpu/arm_cortexa8/omap3/mem.c
+++ b/cpu/arm_cortexa8/omap3/mem.c
@@ -92,7 +92,7 @@ void make_cs1_contiguous(void)
u32 size, a_add_low, a_add_high;
size = get_sdr_cs_size(CS0);
- size /= SZ_32M; /* find size to offset CS1 */
+ size /= (32 << 20); /* find size to offset CS1 */
a_add_high = (size & 3) << 8; /* set up low field */
a_add_low = (size & 0x3C) >> 2; /* set up high field */
writel((a_add_high | a_add_low), &sdrc_base->cs_cfg);
@@ -249,7 +249,7 @@ void gpmc_init(void)
enable_gpmc_cs_config(gpmc_config, &gpmc_cfg->cs[0], base, size);
#if defined(CONFIG_ENV_IS_IN_NAND)
f_off = SMNAND_ENV_OFFSET;
- f_sec = SZ_128K;
+ f_sec = (128 << 10);
/* env setup */
boot_flash_base = base;
boot_flash_off = f_off;
@@ -265,7 +265,7 @@ void gpmc_init(void)
enable_gpmc_cs_config(gpmc_config, &gpmc_cfg->cs[0], base, size);
#if defined(CONFIG_ENV_IS_IN_ONENAND)
f_off = ONENAND_ENV_OFFSET;
- f_sec = SZ_128K;
+ f_sec = (128 << 10);
/* env setup */
boot_flash_base = base;
boot_flash_off = f_off;
diff --git a/cpu/arm_cortexa8/omap3/sys_info.c b/cpu/arm_cortexa8/omap3/sys_info.c
index 765aaf2..95f588a 100644
--- a/cpu/arm_cortexa8/omap3/sys_info.c
+++ b/cpu/arm_cortexa8/omap3/sys_info.c
@@ -124,7 +124,7 @@ u32 get_sdr_cs_size(u32 cs)
/* get ram size field */
size = readl(&sdrc_base->cs[cs].mcfg) >> 8;
size &= 0x3FF; /* remove unwanted bits */
- size *= SZ_2M; /* find size in MB */
+ size *= (2 << 20); /* find size in MB */
return size;
}
diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h
index cd40da6..af6b176 100644
--- a/include/configs/devkit8000.h
+++ b/include/configs/devkit8000.h
@@ -30,7 +30,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/sizes.h>
/* High Level Configuration Options */
#define CONFIG_ARMCORTEXA8 1 /* This is an ARM V7 CPU core */
@@ -59,9 +58,9 @@
#define CONFIG_REVISION_TAG 1
/* Size of malloc() pool */
-#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
/* initial data */
@@ -270,16 +269,16 @@
#define CONFIG_SYS_HZ 1000
/* The stack sizes are set up in start.S using the settings below */
-#define CONFIG_STACKSIZE SZ_128K /* regular stack */
+#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */
+#define CONFIG_STACKSIZE_IRQ (128 << 10) /* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ (128 << 10) /* FIQ stack 4 KiB */
#endif
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE SZ_128M /* at least 128 meg */
+#define PHYS_SDRAM_1_SIZE (128 << 20) /* at least 128 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/* SDRAM Bank Allocation method */
@@ -288,7 +287,7 @@
/* NAND and environment organization */
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
-#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_ENV_IS_IN_NAND 1
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index 61629f8..e94fbd7 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -27,7 +27,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/sizes.h>
/*
* High Level Configuration Options
@@ -62,9 +61,9 @@
/*
* Size of malloc() pool
*/
-#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
/* initial data */
@@ -238,10 +237,10 @@
*
* The stack sizes are set up in start.S using the settings below
*/
-#define CONFIG_STACKSIZE SZ_128K /* regular stack */
+#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */
+#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */
#endif
/*-----------------------------------------------------------------------
@@ -249,7 +248,7 @@
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
+#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/* SDRAM Bank Allocation method */
@@ -268,7 +267,7 @@
#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
/* one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_SYS_FLASH_BASE boot_flash_base
diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h
index 9f0f34b..ee424f7 100644
--- a/include/configs/omap3_evm.h
+++ b/include/configs/omap3_evm.h
@@ -32,7 +32,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/sizes.h>
/*
* High Level Configuration Options
@@ -67,9 +66,9 @@
/*
* Size of malloc() pool
*/
-#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
/* initial data */
/*
@@ -230,10 +229,10 @@
*
* The stack sizes are set up in start.S using the settings below
*/
-#define CONFIG_STACKSIZE SZ_128K /* regular stack */
+#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */
+#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */
#endif
/*-----------------------------------------------------------------------
@@ -241,7 +240,7 @@
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
+#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/* SDRAM Bank Allocation method */
@@ -260,7 +259,7 @@
#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors */
/* on one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_SYS_FLASH_BASE boot_flash_base
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index 07a031b..20450f0 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -19,7 +19,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/sizes.h>
/*
* High Level Configuration Options
@@ -54,9 +53,9 @@
/*
* Size of malloc() pool
*/
-#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
/* initial data */
@@ -223,10 +222,10 @@
*
* The stack sizes are set up in start.S using the settings below
*/
-#define CONFIG_STACKSIZE SZ_128K /* regular stack */
+#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */
+#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */
#endif
/*-----------------------------------------------------------------------
@@ -234,7 +233,7 @@
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
+#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/* SDRAM Bank Allocation method */
@@ -253,7 +252,7 @@
#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
/* one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_SYS_FLASH_BASE boot_flash_base
diff --git a/include/configs/omap3_pandora.h b/include/configs/omap3_pandora.h
index 1cfd7e9..c71baa2 100644
--- a/include/configs/omap3_pandora.h
+++ b/include/configs/omap3_pandora.h
@@ -22,7 +22,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/sizes.h>
/*
* High Level Configuration Options
@@ -57,9 +56,9 @@
/*
* Size of malloc() pool
*/
-#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
/* initial data */
@@ -227,10 +226,10 @@
*
* The stack sizes are set up in start.S using the settings below
*/
-#define CONFIG_STACKSIZE SZ_128K /* regular stack */
+#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */
+#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */
#endif
/*-----------------------------------------------------------------------
@@ -238,7 +237,7 @@
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
+#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/* SDRAM Bank Allocation method */
@@ -257,7 +256,7 @@
#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
/* one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_SYS_FLASH_BASE boot_flash_base
diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h
index 61a41e7..97fe989 100644
--- a/include/configs/omap3_zoom1.h
+++ b/include/configs/omap3_zoom1.h
@@ -28,7 +28,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/sizes.h>
/*
* High Level Configuration Options
@@ -63,9 +62,9 @@
/*
* Size of malloc() pool
*/
-#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
/* initial data */
@@ -235,10 +234,10 @@
*
* The stack sizes are set up in start.S using the settings below
*/
-#define CONFIG_STACKSIZE SZ_128K /* regular stack */
+#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ SZ_4K /* IRQ stack */
-#define CONFIG_STACKSIZE_FIQ SZ_4K /* FIQ stack */
+#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */
#endif
/*-----------------------------------------------------------------------
@@ -246,7 +245,7 @@
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
+#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/* SDRAM Bank Allocation method */
@@ -265,7 +264,7 @@
#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
/* one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_SYS_FLASH_BASE boot_flash_base
diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h
index 03f92f5..e8086ef 100644
--- a/include/configs/omap3_zoom2.h
+++ b/include/configs/omap3_zoom2.h
@@ -29,7 +29,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/sizes.h>
/*
* High Level Configuration Options
@@ -64,9 +63,9 @@
/*
* Size of malloc() pool
*/
-#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
/* initial data */
/*
@@ -200,10 +199,10 @@
*
* The stack sizes are set up in start.S using these settings
*/
-#define CONFIG_STACKSIZE SZ_128K
+#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ SZ_4K
-#define CONFIG_STACKSIZE_FIQ SZ_4K
+#define CONFIG_STACKSIZE_IRQ (4 << 10) /* IRQ stack 4 KiB */
+#define CONFIG_STACKSIZE_FIQ (4 << 10) /* FIQ stack 4 KiB */
#endif
/*-----------------------------------------------------------------------
@@ -211,7 +210,7 @@
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
+#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
/* SDRAM Bank Allocation method */
@@ -230,7 +229,7 @@
#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
/* one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_SYS_FLASH_BASE boot_flash_base
--
1.6.0.4
More information about the U-Boot
mailing list