[U-Boot] [PATCH 7/7] powerpc/p1021mds: add QE and UEC support

Haiying Wang Haiying.Wang at freescale.com
Mon Aug 16 10:25:39 CEST 2010


P1021 has some QE pins which need to be set in pmuxcr register before using QE
functions. In this patch, pin QE0 and QE3 are set for UCC1 and UCC5 in Eth mode.
QE9 and QE12 are set for MII management. QE12 needs to be released after MII
access because QE12 pin is muxed with LBCTL signal.

Signed-off-by: Haiying Wang <Haiying.Wang at freescale.com>
---
 arch/powerpc/cpu/mpc85xx/speed.c      |    4 ++
 arch/powerpc/include/asm/immap_85xx.h |   13 ++++++++
 board/freescale/p1021mds/p1021mds.c   |   54 +++++++++++++++++++++++++++++++++
 drivers/qe/uec.c                      |   36 ++++++++++++++++++++++
 include/configs/P1021MDS.h            |   44 ++++++++++++++++++++++++++
 5 files changed, 151 insertions(+), 0 deletions(-)

diff --git a/arch/powerpc/cpu/mpc85xx/speed.c b/arch/powerpc/cpu/mpc85xx/speed.c
index dd4c6b3..6f1aa7b 100644
--- a/arch/powerpc/cpu/mpc85xx/speed.c
+++ b/arch/powerpc/cpu/mpc85xx/speed.c
@@ -163,10 +163,14 @@ void get_sys_info (sys_info_t * sysInfo)
 #endif
 
 #ifdef CONFIG_QE
+#ifdef CONFIG_P1021
+	sysInfo->freqQE =  sysInfo->freqSystemBus;
+#else
 	qe_ratio = ((gur->porpllsr) & MPC85xx_PORPLLSR_QE_RATIO)
 			>> MPC85xx_PORPLLSR_QE_RATIO_SHIFT;
 	sysInfo->freqQE = qe_ratio * CONFIG_SYS_CLK_FREQ;
 #endif
+#endif
 
 #if defined(CONFIG_SYS_LBC_LCRR)
 	/* We will program LCRR to this value later */
diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h
index 5eeb93a..896014b 100644
--- a/arch/powerpc/include/asm/immap_85xx.h
+++ b/arch/powerpc/include/asm/immap_85xx.h
@@ -1923,6 +1923,19 @@ typedef struct ccsr_gur {
 #define MPC85xx_PMUXCR_SD_DATA		0x80000000
 #define MPC85xx_PMUXCR_SDHC_CD		0x40000000
 #define MPC85xx_PMUXCR_SDHC_WP		0x20000000
+#define MPC85xx_PMUXCR_QE0             0x00008000
+#define MPC85xx_PMUXCR_QE1             0x00004000
+#define MPC85xx_PMUXCR_QE2             0x00002000
+#define MPC85xx_PMUXCR_QE3             0x00001000
+#define MPC85xx_PMUXCR_QE4             0x00000800
+#define MPC85xx_PMUXCR_QE5             0x00000400
+#define MPC85xx_PMUXCR_QE6             0x00000200
+#define MPC85xx_PMUXCR_QE7             0x00000100
+#define MPC85xx_PMUXCR_QE8             0x00000080
+#define MPC85xx_PMUXCR_QE9             0x00000040
+#define MPC85xx_PMUXCR_QE10            0x00000020
+#define MPC85xx_PMUXCR_QE11            0x00000010
+#define MPC85xx_PMUXCR_QE12            0x00000008
 	u32	pmuxcr2;	/* Alt. function signal multiplex control 2 */
 	u8	res6[8];
 	u32	devdisr;	/* Device disable control */
diff --git a/board/freescale/p1021mds/p1021mds.c b/board/freescale/p1021mds/p1021mds.c
index c61c902..9297d0c 100644
--- a/board/freescale/p1021mds/p1021mds.c
+++ b/board/freescale/p1021mds/p1021mds.c
@@ -24,6 +24,48 @@
 #include <tsec.h>
 #include <netdev.h>
 
+#include "bcsr.h"
+
+#ifdef CONFIG_QE
+const qe_iop_conf_t qe_iop_conf_tab[] = {
+	/* QE_MUX_MDC */
+	{1,  19, 1, 0, 1}, /* QE_MUX_MDC               */
+
+	/* QE_MUX_MDIO */
+	{1,  20, 3, 0, 1}, /* QE_MUX_MDIO              */
+
+	/* UCC_1_MII */
+	{0, 23, 2, 0, 2}, /* CLK12 */
+	{0, 24, 2, 0, 1}, /* CLK9 */
+	{0,  7, 1, 0, 2}, /* ENET1_TXD0_SER1_TXD0      */
+	{0,  9, 1, 0, 2}, /* ENET1_TXD1_SER1_TXD1      */
+	{0, 11, 1, 0, 2}, /* ENET1_TXD2_SER1_TXD2      */
+	{0, 12, 1, 0, 2}, /* ENET1_TXD3_SER1_TXD3      */
+	{0,  6, 2, 0, 2}, /* ENET1_RXD0_SER1_RXD0      */
+	{0, 10, 2, 0, 2}, /* ENET1_RXD1_SER1_RXD1      */
+	{0, 14, 2, 0, 2}, /* ENET1_RXD2_SER1_RXD2      */
+	{0, 15, 2, 0, 2}, /* ENET1_RXD3_SER1_RXD3      */
+	{0,  5, 1, 0, 2}, /* ENET1_TX_EN_SER1_RTS_B    */
+	{0, 13, 1, 0, 2}, /* ENET1_TX_ER               */
+	{0,  4, 2, 0, 2}, /* ENET1_RX_DV_SER1_CTS_B    */
+	{0,  8, 2, 0, 2}, /* ENET1_RX_ER_SER1_CD_B    */
+	{0, 17, 2, 0, 2}, /* ENET1_CRS    */
+	{0, 16, 2, 0, 2}, /* ENET1_COL    */
+
+	/* UCC_5_RMII */
+	{1, 11, 2, 0, 1}, /* CLK13 */
+	{1, 7,  1, 0, 2}, /* ENET5_TXD0_SER5_TXD0      */
+	{1, 10, 1, 0, 2}, /* ENET5_TXD1_SER5_TXD1      */
+	{1, 6, 2, 0, 2}, /* ENET5_RXD0_SER5_RXD0      */
+	{1, 9, 2, 0, 2}, /* ENET5_RXD1_SER5_RXD1      */
+	{1, 5, 1, 0, 2}, /* ENET5_TX_EN_SER5_RTS_B    */
+	{1, 4, 2, 0, 2}, /* ENET5_RX_DV_SER5_CTS_B    */
+	{1, 8, 2, 0, 2}, /* ENET5_RX_ER_SER5_CD_B    */
+
+	{0,  0, 0, 0, QE_IOP_TAB_END} /* END of table */
+};
+#endif
+
 const char *board_hwconfig = "foo:bar=baz";
 const char *cpu_hwconfig = "foo:bar=baz";
 
@@ -88,6 +130,14 @@ int board_eth_init(bd_t *bis)
 
 	tsec_eth_init(bis, tsec_info, num);
 
+#if defined(CONFIG_UEC_ETH)
+	/*  QE0 and QE3 need to be exposed for UCC1 and UCC5 Eth mode */
+	setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE0);
+	setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE3);
+
+	uec_standard_init(bis);
+#endif
+
 	return pci_eth_init(bis);
 }
 #endif
@@ -109,6 +159,10 @@ void ft_board_setup(void *blob, bd_t *bd)
 
 	ft_pci_board_setup(blob);
 
+#ifdef CONFIG_QE
+	do_fixup_by_compat(blob, "fsl,qe", "status", "okay",
+			sizeof("okay"), 0);
+#endif
 }
 #endif
 ;
diff --git a/drivers/qe/uec.c b/drivers/qe/uec.c
index ccbf27d..e434564 100644
--- a/drivers/qe/uec.c
+++ b/drivers/qe/uec.c
@@ -30,6 +30,9 @@
 #include "uec.h"
 #include "uec_phy.h"
 #include "miiphy.h"
+#ifdef CONFIG_P1021
+#include "../../board/freescale/p1021mds/bcsr.h"
+#endif
 
 /* Default UTBIPAR SMI address */
 #ifndef CONFIG_UTBIPAR_INIT_TBIPA
@@ -588,9 +591,25 @@ static void phy_change(struct eth_device *dev)
 {
 	uec_private_t	*uec = (uec_private_t *)dev->priv;
 
+#ifdef CONFIG_P1021
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+
+	/* QE9 and QE12 need to be set for enabling QE MII managment signals */
+	setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE9);
+	setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12);
+#endif
+
 	/* Update the link, speed, duplex */
 	uec->mii_info->phyinfo->read_status(uec->mii_info);
 
+#ifdef CONFIG_P1021
+	/*
+	 * QE12 is muxed with LBCTL, it needs to be released for enabling
+	 * LBCTL signal for LBC usage.
+	 */
+	clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12);
+#endif
+
 	/* Adjust the interface according to speed */
 	adjust_link(dev);
 }
@@ -1198,10 +1217,22 @@ static int uec_init(struct eth_device* dev, bd_t *bd)
 	uec_private_t		*uec;
 	int			err, i;
 	struct phy_info         *curphy;
+#ifdef CONFIG_P1021
+	ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+#endif
 
 	uec = (uec_private_t *)dev->priv;
 
 	if (uec->the_first_run == 0) {
+#ifdef CONFIG_P1021
+	/* reset micrel phy for each UEC */
+	reset_p1021mds_micrel_phy();
+
+	/* QE9 and QE12 need to be set for enabling QE MII managment signals */
+	setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE9);
+	setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12);
+#endif
+
 		err = init_phy(dev);
 		if (err) {
 			printf("%s: Cannot initialize PHY, aborting.\n",
@@ -1226,6 +1257,11 @@ static int uec_init(struct eth_device* dev, bd_t *bd)
 			udelay(100000);
 		} while (((i-- > 0) && !uec->mii_info->link) || err);
 
+#ifdef CONFIG_P1021
+		/* QE12 needs to be released for enabling LBCTL signal*/
+		clrbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE12);
+#endif
+
 		if (err || i <= 0)
 			printf("warning: %s: timeout on PHY link\n", dev->name);
 
diff --git a/include/configs/P1021MDS.h b/include/configs/P1021MDS.h
index 6f63aac..1d51852 100644
--- a/include/configs/P1021MDS.h
+++ b/include/configs/P1021MDS.h
@@ -342,6 +342,50 @@
 #define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
 #endif /* CONFIG_TSEC_ENET */
 
+#define CONFIG_QE
+
+#ifdef CONFIG_QE
+/* QE microcode/firmware address */
+#define CONFIG_SYS_QE_FW_IN_NAND 0x1f00000
+#define CONFIG_SYS_QE_FW_ADDR   0x10000000
+#define CONFIG_SYS_QE_FW_LENGTH 0x10000
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_MIIM_ADDRESS	(CONFIG_SYS_CCSRBAR + 0x82120)
+
+#define CONFIG_UEC_ETH
+#define CONFIG_PHY_MODE_NEED_CHANGE
+
+#define CONFIG_UEC_ETH1		/* GETH1 */
+#define CONFIG_HAS_ETH0
+
+#ifdef CONFIG_UEC_ETH1
+#define CONFIG_SYS_UEC1_UCC_NUM		0       	/* UCC1 */
+#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK12	/* CLK12 for MII */
+#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK9		/* CLK9 for MII */
+#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR	0x0     	/* 0x0 for MII */
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE	MII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED	100
+#endif /* CONFIG_UEC_ETH1 */
+
+#define CONFIG_UEC_ETH5		/* GETH5 */
+#define CONFIG_HAS_ETH1
+
+#ifdef CONFIG_UEC_ETH5
+#define CONFIG_SYS_UEC5_UCC_NUM		4       	/* UCC5 */
+#define CONFIG_SYS_UEC5_RX_CLK		QE_CLK_NONE
+#define CONFIG_SYS_UEC5_TX_CLK		QE_CLK13	/* CLK 13 for RMII */
+#define CONFIG_SYS_UEC5_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC5_PHY_ADDR	0x3		/* 0x3 for RMII */
+#define CONFIG_SYS_UEC5_INTERFACE_TYPE	RMII
+#define CONFIG_SYS_UEC5_INTERFACE_SPEED	100
+#endif /* CONFIG_UEC_ETH2 */
+
+#endif /* CONFIG_QE */
+
 /*
  * I2C
  */
-- 
1.7.0






More information about the U-Boot mailing list