[U-Boot] [PATCH v3] 83xx: add support for ve8313 board
Heiko Schocher
hs at denx.de
Wed Jul 7 12:26:34 CEST 2010
This patch add support for the ve8313 board based on
Freescale MPC8313 CPU.
- serial console on UART 1
- 128 MB DDR RAM
- 32 MB NOR Flash
- 16 MB NAND Flash
- Ethernet MII Mode over on TSEC0
- micrel ksz804 phy
- Hardware WDT MAX824
changes since v1
- Environment size = sector size
- use red. environment
- add comments from Kim Phillips
- add MAKEALL, MAINTAINERS entry
- Codingstyle issues fixed
- inserted original Copyrights
- PCI subsys vendor ID changed from 0x1057 (Motorola)
to 0x1957 (Freescale)
changes since v2
- add comments from Wolfgang Denk
- fix Codingstyle and some comments
- reworked WDT reset (just toggling the WD_TRIG pin)
- Environment size now 16KiB
- fixed RAMBOOT version
- fixed CONFIG_SYS_LOAD_ADDR
- renamed CONFIG_TSEC1_NAME to TSEC1
Signed-off-by: Heiko Schocher <hs at denx.de>
---
MAINTAINERS | 1 +
MAKEALL | 1 +
board/ve8313/Makefile | 50 +++++
board/ve8313/config.mk | 7 +
board/ve8313/ve8313.c | 215 +++++++++++++++++++
boards.cfg | 1 +
include/configs/ve8313.h | 511 ++++++++++++++++++++++++++++++++++++++++++++++
7 files changed, 786 insertions(+), 0 deletions(-)
create mode 100644 board/ve8313/Makefile
create mode 100644 board/ve8313/config.mk
create mode 100644 board/ve8313/ve8313.c
create mode 100644 include/configs/ve8313.h
diff --git a/MAINTAINERS b/MAINTAINERS
index d7aec98..88a3d79 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -427,6 +427,7 @@ Heiko Schocher <hs at denx.de>
sc3 PPC405GP
suen3 ARM926EJS (Kirkwood SoC)
uc101 MPC5200
+ ve8313 MPC8313
Peter De Schrijver <p2 at mind.be>
diff --git a/MAKEALL b/MAKEALL
index 27f8bd1..eedae60 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -379,6 +379,7 @@ LIST_83xx=" \
sbc8349 \
SIMPC8313_LP \
TQM834x \
+ ve8313 \
vme8349 \
"
diff --git a/board/ve8313/Makefile b/board/ve8313/Makefile
new file mode 100644
index 0000000..c95f90e
--- /dev/null
+++ b/board/ve8313/Makefile
@@ -0,0 +1,50 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := $(BOARD).o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/ve8313/config.mk b/board/ve8313/config.mk
new file mode 100644
index 0000000..02dd33e
--- /dev/null
+++ b/board/ve8313/config.mk
@@ -0,0 +1,7 @@
+ifndef NAND_SPL
+sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
+endif
+
+ifndef TEXT_BASE
+TEXT_BASE = 0xfe000000
+endif
diff --git a/board/ve8313/ve8313.c b/board/ve8313/ve8313.c
new file mode 100644
index 0000000..8ba1b19
--- /dev/null
+++ b/board/ve8313/ve8313.c
@@ -0,0 +1,215 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006-2007
+ *
+ * Author: Scott Wood <scottwood at freescale.com>
+ *
+ * (C) Copyright 2010
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS for A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <libfdt.h>
+#include <pci.h>
+#include <mpc83xx.h>
+#include <ns16550.h>
+#include <nand.h>
+
+#include <asm/bitops.h>
+#include <asm/io.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+extern void disable_addr_trans (void);
+extern void enable_addr_trans (void);
+
+int checkboard(void)
+{
+ puts("Board: ve8313\n");
+ return 0;
+}
+
+static long fixed_sdram(void)
+{
+ u32 msize = CONFIG_SYS_DDR_SIZE * 1024 * 1024;
+
+#ifndef CONFIG_SYS_RAMBOOT
+ volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+ u32 msize_log2 = __ilog2(msize);
+
+ out_be32(&im->sysconf.ddrlaw[0].bar,
+ (CONFIG_SYS_DDR_SDRAM_BASE & 0xfffff000));
+ out_be32(&im->sysconf.ddrlaw[0].ar, (LBLAWAR_EN | (msize_log2 - 1)));
+ out_be32(&im->sysconf.ddrcdr, CONFIG_SYS_DDRCDR_VALUE);
+
+ /*
+ * Erratum DDR3 requires a 50ms delay after clearing DDRCDR[DDR_cfg],
+ * or the DDR2 controller may fail to initialize correctly.
+ */
+ __udelay(50000);
+
+ out_be32(&im->ddr.csbnds[0].csbnds, (msize - 1) >> 24);
+ out_be32(&im->ddr.cs_config[0], CONFIG_SYS_DDR_CONFIG);
+
+ /* Currently we use only one CS, so disable the other bank. */
+ out_be32(&im->ddr.cs_config[1], 0);
+
+ out_be32(&im->ddr.sdram_clk_cntl, CONFIG_SYS_DDR_CLK_CNTL);
+ out_be32(&im->ddr.timing_cfg_3, CONFIG_SYS_DDR_TIMING_3);
+ out_be32(&im->ddr.timing_cfg_1, CONFIG_SYS_DDR_TIMING_1);
+ out_be32(&im->ddr.timing_cfg_2, CONFIG_SYS_DDR_TIMING_2);
+ out_be32(&im->ddr.timing_cfg_0, CONFIG_SYS_DDR_TIMING_0);
+
+ out_be32(&im->ddr.sdram_cfg, CONFIG_SYS_SDRAM_CFG);
+
+ out_be32(&im->ddr.sdram_cfg2, CONFIG_SYS_SDRAM_CFG2);
+ out_be32(&im->ddr.sdram_mode, CONFIG_SYS_DDR_MODE);
+ out_be32(&im->ddr.sdram_mode2, CONFIG_SYS_DDR_MODE_2);
+
+ out_be32(&im->ddr.sdram_interval, CONFIG_SYS_DDR_INTERVAL);
+ sync();
+
+ /* enable DDR controller */
+ setbits_be32(&im->ddr.sdram_cfg, SDRAM_CFG_MEM_EN);
+
+ /* now check the real size */
+ disable_addr_trans ();
+ msize = get_ram_size (CONFIG_SYS_DDR_BASE, msize);
+ enable_addr_trans ();
+#endif
+
+ return msize;
+}
+
+phys_size_t initdram(int board_type)
+{
+ volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+ volatile fsl_lbus_t *lbc = &im->lbus;
+ u32 msize;
+
+ if ((im->sysconf.immrbar & IMMRBAR_BASE_ADDR) != (u32)im)
+ return -1;
+
+ /* DDR SDRAM - Main SODIMM */
+ msize = fixed_sdram();
+
+ /* Local Bus setup lbcr and mrtpr */
+ out_be32(&lbc->lbcr, CONFIG_SYS_LBC_LBCR);
+ out_be32(&lbc->mrtpr, CONFIG_SYS_LBC_MRTPR);
+ sync();
+
+ /* return total bus SDRAM size(bytes) -- DDR */
+ return msize;
+}
+
+#define VE8313_WDT_EN 0x00020000
+#define VE8313_WDT_TRIG 0x00040000
+
+int board_early_init_f (void)
+{
+ volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+ volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)im->gpio;
+
+#if defined(CONFIG_HW_WATCHDOG)
+ /* enable WDT */
+ clrbits_be32(&gpio->dat, VE8313_WDT_EN | VE8313_WDT_TRIG);
+#else
+ /* disable WDT */
+ setbits_be32(&gpio->dat, VE8313_WDT_EN | VE8313_WDT_TRIG);
+#endif
+ /* set WDT pins as output */
+ setbits_be32(&gpio->dir, VE8313_WDT_EN | VE8313_WDT_TRIG);
+
+ return 0;
+}
+
+#if defined(CONFIG_HW_WATCHDOG)
+void hw_watchdog_reset(void)
+{
+ volatile immap_t *im = (volatile immap_t *)CONFIG_SYS_IMMR;
+ volatile gpio83xx_t *gpio = (volatile gpio83xx_t *)im->gpio;
+ unsigned long reg;
+
+ reg = in_be32(&gpio->dat);
+ if (reg & VE8313_WDT_TRIG)
+ clrbits_be32(&gpio->dat, VE8313_WDT_TRIG);
+ else
+ setbits_be32(&gpio->dat, VE8313_WDT_TRIG);
+}
+#endif
+
+
+#if defined(CONFIG_PCI)
+static struct pci_region pci_regions[] = {
+ {
+ bus_start: CONFIG_SYS_PCI1_MEM_BASE,
+ phys_start: CONFIG_SYS_PCI1_MEM_PHYS,
+ size: CONFIG_SYS_PCI1_MEM_SIZE,
+ flags: PCI_REGION_MEM | PCI_REGION_PREFETCH
+ },
+ {
+ bus_start: CONFIG_SYS_PCI1_MMIO_BASE,
+ phys_start: CONFIG_SYS_PCI1_MMIO_PHYS,
+ size: CONFIG_SYS_PCI1_MMIO_SIZE,
+ flags: PCI_REGION_MEM
+ },
+ {
+ bus_start: CONFIG_SYS_PCI1_IO_BASE,
+ phys_start: CONFIG_SYS_PCI1_IO_PHYS,
+ size: CONFIG_SYS_PCI1_IO_SIZE,
+ flags: PCI_REGION_IO
+ }
+};
+
+void pci_init_board(void)
+{
+ volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
+ volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
+ volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+ struct pci_region *reg[] = { pci_regions };
+ int warmboot;
+
+ /* Enable all 3 PCI_CLK_OUTPUTs. */
+ setbits_be32(&clk->occr, 0xe0000000);
+
+ /*
+ * Configure PCI Local Access Windows
+ */
+ out_be32(&pci_law[0].bar, CONFIG_SYS_PCI1_MEM_PHYS & LAWBAR_BAR);
+ out_be32(&pci_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+ out_be32(&pci_law[1].bar, CONFIG_SYS_PCI1_IO_PHYS & LAWBAR_BAR);
+ out_be32(&pci_law[1].ar, LBLAWAR_EN | LBLAWAR_1MB);
+
+ warmboot = gd->bd->bi_bootflags & BOOTFLAG_WARM;
+
+ mpc83xx_pci_init(1, reg, warmboot);
+}
+#endif
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ ft_cpu_setup(blob, bd);
+#ifdef CONFIG_PCI
+ ft_pci_setup(blob, bd);
+#endif
+}
+#endif
diff --git a/boards.cfg b/boards.cfg
index 1a5cfb1..cad8ba4 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -132,6 +132,7 @@ ZPC1900 powerpc mpc8260 zpc1900
mgcoge powerpc mpc8260 - keymile
SCM powerpc mpc8260 - siemens
TQM8272 powerpc mpc8260 tqm8272 tqc
+ve8313 powerpc mpc83xx ve8313
kmeter1 powerpc mpc83xx kmeter1 keymile
MVBLM7 powerpc mpc83xx mvblm7 matrix_vision
TQM834x powerpc mpc83xx tqm834x tqc
diff --git a/include/configs/ve8313.h b/include/configs/ve8313.h
new file mode 100644
index 0000000..1589913
--- /dev/null
+++ b/include/configs/ve8313.h
@@ -0,0 +1,511 @@
+/*
+ * Copyright (C) Freescale Semiconductor, Inc. 2006.
+ *
+ * (C) Copyright 2010
+ * Heiko Schocher, DENX Software Engineering, hs at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+/*
+ * ve8313 board configuration file
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300 1
+#define CONFIG_MPC83xx 1
+#define CONFIG_MPC831x 1
+#define CONFIG_MPC8313 1
+#define CONFIG_VE8313 1
+
+#define CONFIG_PCI 1
+
+#define CONFIG_BOARD_EARLY_INIT_F 1
+
+/*
+ * On-board devices
+ *
+ */
+#define CONFIG_83XX_CLKIN 32000000 /* in Hz */
+
+#define CONFIG_SYS_CLK_FREQ CONFIG_83XX_CLKIN
+
+#define CONFIG_SYS_IMMR 0xE0000000
+
+#define CONFIG_SYS_MEMTEST_START 0x00001000
+#define CONFIG_SYS_MEMTEST_END 0x07000000
+
+#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth */
+#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count */
+
+/*
+ * Device configurations
+ */
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+
+/*
+ * Manually set up DDR parameters, as this board does not
+ * have the SPD connected to I2C.
+ */
+#define CONFIG_SYS_DDR_SIZE 128 /* MB */
+#define CONFIG_SYS_DDR_CONFIG ( CSCONFIG_EN \
+ | CSCONFIG_AP \
+ | 0x00040000 /* TODO */ \
+ | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 )
+ /* 0x80840102 */
+
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+#define CONFIG_SYS_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
+ | ( 0 << TIMING_CFG0_WRT_SHIFT ) \
+ | ( 3 << TIMING_CFG0_RRT_SHIFT ) \
+ | ( 2 << TIMING_CFG0_WWT_SHIFT ) \
+ | ( 7 << TIMING_CFG0_ACT_PD_EXIT_SHIFT ) \
+ | ( 2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT ) \
+ | ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
+ | ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
+ /* 0x0e720802 */
+#define CONFIG_SYS_DDR_TIMING_1 ( ( 2 << TIMING_CFG1_PRETOACT_SHIFT ) \
+ | ( 6 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
+ | ( 2 << TIMING_CFG1_ACTTORW_SHIFT ) \
+ | ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
+ | ( 6 << TIMING_CFG1_REFREC_SHIFT ) \
+ | ( 2 << TIMING_CFG1_WRREC_SHIFT ) \
+ | ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
+ | ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
+ /* 0x26256222 */
+#define CONFIG_SYS_DDR_TIMING_2 ( ( 0 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+ | ( 5 << TIMING_CFG2_CPO_SHIFT ) \
+ | ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
+ | ( 1 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
+ | ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
+ | ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
+ | ( 7 << TIMING_CFG2_FOUR_ACT_SHIFT) )
+ /* 0x029028c7 */
+#define CONFIG_SYS_DDR_INTERVAL ( ( 0x320 << SDRAM_INTERVAL_REFINT_SHIFT ) \
+ | ( 0x2000 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
+ /* 0x03202000 */
+#define CONFIG_SYS_SDRAM_CFG ( SDRAM_CFG_SREN \
+ | SDRAM_CFG_SDRAM_TYPE_DDR2 \
+ | SDRAM_CFG_32_BE )
+ /* 0x43080000 */
+#define CONFIG_SYS_SDRAM_CFG2 0x00401000
+#define CONFIG_SYS_DDR_MODE ( ( 0x4440 << SDRAM_MODE_ESD_SHIFT ) \
+ | ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
+ /* 0x44400232 */
+#define CONFIG_SYS_DDR_MODE_2 0x8000C000
+
+#define CONFIG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+ /*0x02000000*/
+#define CONFIG_SYS_DDRCDR_VALUE ( DDRCDR_EN \
+ | DDRCDR_PZ_NOMZ \
+ | DDRCDR_NZ_NOMZ \
+ | DDRCDR_M_ODR )
+ /* 0x73000002 */
+
+/*
+ * FLASH on the Local Bus
+ */
+#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CONFIG_SYS_FLASH_BASE 0xFE000000
+#define CONFIG_SYS_FLASH_SIZE 32 /* size in MB */
+#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* buffer up multiple bytes */
+
+#define CONFIG_SYS_NOR_BR_PRELIM (CONFIG_SYS_FLASH_BASE | \
+ (2 << BR_PS_SHIFT) | /* 16 bit */ \
+ BR_V) /* valid */
+#define CONFIG_SYS_NOR_OR_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_ACS_DIV4 \
+ | OR_GPCM_SCY_5 \
+ | OR_GPCM_TRLX \
+ | OR_GPCM_EAD)
+ /* 0xfe000c55 */
+
+#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM 0x80000018 /* 32 MB window size */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256 /* sectors per dev */
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM*/
+
+#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - \
+ CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
+#define CONFIG_SYS_MONITOR_LEN (384 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (512 * 1024)
+
+/*
+ * Local Bus LCRR and LBCR regs
+ */
+#define CONFIG_SYS_LCRR_EADC LCRR_EADC_3
+#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_2
+
+#define CONFIG_SYS_LBC_LBCR 0x00040000
+
+#define CONFIG_SYS_LBC_MRTPR 0x20000000
+
+/*
+ * NAND settings
+ */
+#define CONFIG_SYS_NAND_BASE 0x61000000
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND 1
+#define CONFIG_NAND_FSL_ELBC 1
+#define CONFIG_SYS_NAND_BLOCK_SIZE 16384
+
+#define CONFIG_SYS_NAND_BR_PRELIM ( CONFIG_SYS_NAND_BASE \
+ | BR_PS_8 \
+ | BR_DECC_CHK_GEN \
+ | BR_MS_FCM \
+ | BR_V ) /* valid */
+ /* 0x61000c21 */
+#define CONFIG_SYS_NAND_OR_PRELIM (0xffff8000 \
+ | OR_FCM_BCTLD \
+ | OR_FCM_CHT \
+ | OR_FCM_SCY_2 \
+ | OR_FCM_RST \
+ | OR_FCM_TRLX)
+ /* 0xffff90ac */
+
+#define CONFIG_SYS_BR0_PRELIM CONFIG_SYS_NOR_BR_PRELIM
+#define CONFIG_SYS_OR0_PRELIM CONFIG_SYS_NOR_OR_PRELIM
+#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM
+
+#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_NAND_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
+
+#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
+#define CONFIG_SYS_NAND_LBLAWAR_PRELIM CONFIG_SYS_LBLAWAR1_PRELIM
+
+/* CS2 NvRAM */
+#define CONFIG_SYS_BR2_PRELIM (0x60000000 \
+ | BR_PS_8 \
+ | BR_V)
+ /* 0x60000801 */
+#define CONFIG_SYS_OR2_PRELIM (0xfffe0000 \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_3 \
+ | OR_GPCM_TRLX \
+ | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
+ /* 0xfffe0937 */
+/* local bus read write buffer mapping SRAM at 0x64000000 */
+#define CONFIG_SYS_BR3_PRELIM (0x62000000 \
+ | BR_PS_16 \
+ | BR_V)
+ /* 0x62001001 */
+
+#define CONFIG_SYS_OR3_PRELIM (0xfe000000 \
+ | OR_GPCM_CSNT \
+ | OR_GPCM_XACS \
+ | OR_GPCM_SCY_15 \
+ | OR_GPCM_TRLX \
+ | OR_GPCM_EHTR \
+ | OR_GPCM_EAD)
+ /* 0xfe0009f7 */
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+#if defined(CONFIG_PCI)
+/*
+ * General PCI
+ * Addresses are mapped 1-1.
+ */
+#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
+#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+#endif
+
+/*
+ * TSEC
+ */
+#define CONFIG_TSEC_ENET /* TSEC ethernet support */
+
+#define CONFIG_NET_MULTI
+
+#define CONFIG_TSEC1
+#ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
+#define CONFIG_TSEC1_NAME "TSEC1"
+#define CONFIG_SYS_TSEC1_OFFSET 0x24000
+#define TSEC1_PHY_ADDR 0x01
+#define TSEC1_FLAGS 0
+#define TSEC1_PHYIDX 0
+#endif
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME "TSEC1"
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \
+ CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
+#define CONFIG_ENV_SIZE 0x4000
+/* Address and size of Redundant Environment Sector */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
+ CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_PCI
+
+#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg Buffer size */
+#define CONFIG_SYS_HZ 1000 /* 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+
+/* 0x64050000 */
+#define CONFIG_SYS_HRCW_LOW (\
+ 0x20000000 /* reserved, must be set */ |\
+ HRCWL_DDRCM |\
+ HRCWL_CSB_TO_CLKIN_4X1 | \
+ HRCWL_CORE_TO_CSB_2_5X1)
+
+/* 0xa0600004 */
+#define CONFIG_SYS_HRCW_HIGH (HRCWH_PCI_HOST | \
+ HRCWH_PCI_ARBITER_ENABLE | \
+ HRCWH_CORE_ENABLE | \
+ HRCWH_FROM_0X00000100 | \
+ HRCWH_BOOTSEQ_DISABLE |\
+ HRCWH_SW_WATCHDOG_DISABLE |\
+ HRCWH_ROM_LOC_LOCAL_16BIT | \
+ HRCWH_TSEC1M_IN_MII | \
+ HRCWH_BIG_ENDIAN | \
+ HRCWH_LALE_EARLY)
+
+/* System IO Config */
+#define CONFIG_SYS_SICRH (0x01000000 | \
+ SICRH_ETSEC2_B | \
+ SICRH_ETSEC2_C | \
+ SICRH_ETSEC2_D | \
+ SICRH_ETSEC2_E | \
+ SICRH_ETSEC2_F | \
+ SICRH_ETSEC2_G | \
+ SICRH_TSOBI1 | \
+ SICRH_TSOBI2)
+ /* 0x010fff03 */
+#define CONFIG_SYS_SICRL (SICRL_LBC | \
+ SICRL_SPI_A | \
+ SICRL_SPI_B | \
+ SICRL_SPI_C | \
+ SICRL_SPI_D | \
+ SICRL_ETSEC2_A)
+ /* 0x33fc0003) */
+
+#define CONFIG_SYS_HID0_INIT 0x000000000
+#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
+ HID0_ENABLE_INSTRUCTION_CACHE)
+
+#define CONFIG_SYS_HID2 HID2_HBE
+
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
+/* DDR @ 0x00000000 */
+#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10)
+#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \
+ BATU_VS | BATU_VP)
+
+#if defined(CONFIG_PCI)
+/* PCI @ 0x80000000 */
+#define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10)
+#define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | \
+ BATU_VS | BATU_VP)
+#else
+#define CONFIG_SYS_IBAT1L (0)
+#define CONFIG_SYS_IBAT1U (0)
+#define CONFIG_SYS_IBAT2L (0)
+#define CONFIG_SYS_IBAT2U (0)
+#endif
+
+/* PCI2 not supported on 8313 */
+#define CONFIG_SYS_IBAT3L (0)
+#define CONFIG_SYS_IBAT3U (0)
+#define CONFIG_SYS_IBAT4L (0)
+#define CONFIG_SYS_IBAT4U (0)
+
+/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
+#define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR | BATL_PP_10 | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | \
+ BATU_VP)
+
+/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
+#define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_10 | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* FPGA, SRAM, NAND @ 0x60000000 */
+#define CONFIG_SYS_IBAT7L (0x60000000 | BATL_PP_10 | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT7U (0x60000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
+#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
+#define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L
+#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
+#define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
+#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U
+#define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
+#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#define CONFIG_NETDEV eth0
+
+#define CONFIG_HOSTNAME ve8313
+#define CONFIG_UBOOTPATH ve8313/u-boot.bin
+
+#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
+#define CONFIG_BAUDRATE 115200
+
+#define XMK_STR(x) #x
+#define MK_STR(x) XMK_STR(x)
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=" MK_STR(CONFIG_NETDEV) "\0" \
+ "ethprime=" MK_STR(CONFIG_TSEC1_NAME) "\0" \
+ "u-boot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "u-boot_addr_r=100000\0" \
+ "load=tftp ${u-boot_addr_r} ${u-boot}\0" \
+ "update=protect off " MK_STR(CONFIG_SYS_FLASH_BASE) " +${filesize};" \
+ "erase " MK_STR(CONFIG_SYS_FLASH_BASE) " +${filesize};" \
+ "cp.b ${u-boot_addr_r} " MK_STR(CONFIG_SYS_FLASH_BASE) \
+ " ${filesize};" \
+ "protect on " MK_STR(CONFIG_SYS_FLASH_BASE) " +${filesize}\0" \
+
+#undef MK_STR
+#undef XMK_STR
+
+#endif /* __CONFIG_H */
--
1.6.2.5
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
More information about the U-Boot
mailing list