[U-Boot] [PATCH v2] nios2: remove EP1C20, EP1S10, EP1S40 boards
Thomas Chou
thomas at wytron.com.tw
Wed Jun 16 08:39:30 CEST 2010
The example configuration files of nios2-generic board can generated
binary to run on the EP1C20, EP1S10, and EP1S40 boards. So the three
boards can be removed.
With nios2-generic approach, the fpga parameter header file can
be generated from hardware designs using tools. Porting u-boot for
nios2 boards is simplified. Vendors can supply their fpga parameter
file or patches to add a new nios2-generic board instance. There is
no need to include other boards support for nios2 in the u-boot
mainline.
Signed-off-by: Thomas Chou <thomas at wytron.com.tw>
---
Hi Scott, please rebase your next branch to Wolfgang's next, 06/14.
v2: rebased to Makefile simplify
MAINTAINERS | 3 -
MAKEALL | 3 -
board/altera/ep1c20/Makefile | 55 -----------
board/altera/ep1c20/config.mk | 31 ------
board/altera/ep1c20/ep1c20.c | 52 ----------
board/altera/ep1s10/Makefile | 55 -----------
board/altera/ep1s10/config.mk | 31 ------
board/altera/ep1s10/ep1s10.c | 52 ----------
board/altera/ep1s40/Makefile | 55 -----------
board/altera/ep1s40/config.mk | 31 ------
board/altera/ep1s40/ep1s40.c | 47 ---------
boards.cfg | 3 -
include/configs/EP1C20.h | 214 -----------------------------------------
include/configs/EP1S10.h | 207 ---------------------------------------
include/configs/EP1S40.h | 207 ---------------------------------------
15 files changed, 0 insertions(+), 1046 deletions(-)
delete mode 100644 board/altera/ep1c20/Makefile
delete mode 100644 board/altera/ep1c20/config.mk
delete mode 100644 board/altera/ep1c20/ep1c20.c
delete mode 100644 board/altera/ep1s10/Makefile
delete mode 100644 board/altera/ep1s10/config.mk
delete mode 100644 board/altera/ep1s10/ep1s10.c
delete mode 100644 board/altera/ep1s40/Makefile
delete mode 100644 board/altera/ep1s40/config.mk
delete mode 100644 board/altera/ep1s40/ep1s40.c
delete mode 100644 include/configs/EP1C20.h
delete mode 100644 include/configs/EP1S10.h
delete mode 100644 include/configs/EP1S40.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 7a13d28..700dd8c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -852,9 +852,6 @@ Scott McNutt <smcnutt at psyent.com>
PCI5441 Nios-II
PK1C20 Nios-II
- EP1C20 Nios-II
- EP1S10 Nios-II
- EP1S40 Nios-II
nios2-generic Nios-II
#########################################################################
diff --git a/MAKEALL b/MAKEALL
index 2527352..56db729 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -815,9 +815,6 @@ LIST_x86=" \
#########################################################################
LIST_nios2=" \
- EP1C20 \
- EP1S10 \
- EP1S40 \
PCI5441 \
PK1C20 \
nios2-generic \
diff --git a/board/altera/ep1c20/Makefile b/board/altera/ep1c20/Makefile
deleted file mode 100644
index acad2aa..0000000
--- a/board/altera/ep1c20/Makefile
+++ /dev/null
@@ -1,55 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-ifneq ($(OBJTREE),$(SRCTREE))
-$(shell mkdir -p $(obj)../common)
-endif
-
-LIB = $(obj)lib$(BOARD).a
-
-COMOBJS := ../common/AMDLV065D.o ../common/epled.o
-
-COBJS := $(BOARD).o $(COMOBJS)
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS)
- $(AR) $(ARFLAGS) $@ $(OBJS)
-
-clean:
- rm -f $(SOBJS) $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/altera/ep1c20/config.mk b/board/altera/ep1c20/config.mk
deleted file mode 100644
index dab2740..0000000
--- a/board/altera/ep1c20/config.mk
+++ /dev/null
@@ -1,31 +0,0 @@
-#
-# (C) Copyright 2005, Psyent Corporation <www.psyent.com>
-# Scott McNutt <smcnutt at psyent.com>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-TEXT_BASE = 0x01fc0000
-
-PLATFORM_CPPFLAGS += -mno-hw-div -mno-hw-mul
-PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/$(VENDOR)/include
-
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG
-endif
diff --git a/board/altera/ep1c20/ep1c20.c b/board/altera/ep1c20/ep1c20.c
deleted file mode 100644
index 82900f7..0000000
--- a/board/altera/ep1c20/ep1c20.c
+++ /dev/null
@@ -1,52 +0,0 @@
-/*
- * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
- * Scott McNutt <smcnutt at psyent.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <netdev.h>
-
-int board_early_init_f (void)
-{
- return 0;
-}
-
-int checkboard (void)
-{
- puts ("BOARD : Altera EP-1C20\n");
- return 0;
-}
-
-phys_size_t initdram (int board_type)
-{
- return (0);
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_SMC91111
- rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
-#endif
- return rc;
-}
-#endif
diff --git a/board/altera/ep1s10/Makefile b/board/altera/ep1s10/Makefile
deleted file mode 100644
index acad2aa..0000000
--- a/board/altera/ep1s10/Makefile
+++ /dev/null
@@ -1,55 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-ifneq ($(OBJTREE),$(SRCTREE))
-$(shell mkdir -p $(obj)../common)
-endif
-
-LIB = $(obj)lib$(BOARD).a
-
-COMOBJS := ../common/AMDLV065D.o ../common/epled.o
-
-COBJS := $(BOARD).o $(COMOBJS)
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS)
- $(AR) $(ARFLAGS) $@ $(OBJS)
-
-clean:
- rm -f $(SOBJS) $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/altera/ep1s10/config.mk b/board/altera/ep1s10/config.mk
deleted file mode 100644
index dab2740..0000000
--- a/board/altera/ep1s10/config.mk
+++ /dev/null
@@ -1,31 +0,0 @@
-#
-# (C) Copyright 2005, Psyent Corporation <www.psyent.com>
-# Scott McNutt <smcnutt at psyent.com>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-TEXT_BASE = 0x01fc0000
-
-PLATFORM_CPPFLAGS += -mno-hw-div -mno-hw-mul
-PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/$(VENDOR)/include
-
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG
-endif
diff --git a/board/altera/ep1s10/ep1s10.c b/board/altera/ep1s10/ep1s10.c
deleted file mode 100644
index cf886da..0000000
--- a/board/altera/ep1s10/ep1s10.c
+++ /dev/null
@@ -1,52 +0,0 @@
-/*
- * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
- * Scott McNutt <smcnutt at psyent.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <netdev.h>
-
-int board_early_init_f (void)
-{
- return 0;
-}
-
-int checkboard (void)
-{
- puts ("BOARD : Altera EP-1S10\n");
- return 0;
-}
-
-phys_size_t initdram (int board_type)
-{
- return (0);
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_SMC91111
- rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
-#endif
- return rc;
-}
-#endif
diff --git a/board/altera/ep1s40/Makefile b/board/altera/ep1s40/Makefile
deleted file mode 100644
index acad2aa..0000000
--- a/board/altera/ep1s40/Makefile
+++ /dev/null
@@ -1,55 +0,0 @@
-#
-# (C) Copyright 2001-2006
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-ifneq ($(OBJTREE),$(SRCTREE))
-$(shell mkdir -p $(obj)../common)
-endif
-
-LIB = $(obj)lib$(BOARD).a
-
-COMOBJS := ../common/AMDLV065D.o ../common/epled.o
-
-COBJS := $(BOARD).o $(COMOBJS)
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS)
- $(AR) $(ARFLAGS) $@ $(OBJS)
-
-clean:
- rm -f $(SOBJS) $(OBJS)
-
-distclean: clean
- rm -f $(LIB) core *.bak $(obj).depend
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
diff --git a/board/altera/ep1s40/config.mk b/board/altera/ep1s40/config.mk
deleted file mode 100644
index dab2740..0000000
--- a/board/altera/ep1s40/config.mk
+++ /dev/null
@@ -1,31 +0,0 @@
-#
-# (C) Copyright 2005, Psyent Corporation <www.psyent.com>
-# Scott McNutt <smcnutt at psyent.com>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-TEXT_BASE = 0x01fc0000
-
-PLATFORM_CPPFLAGS += -mno-hw-div -mno-hw-mul
-PLATFORM_CPPFLAGS += -I$(TOPDIR)/board/$(VENDOR)/include
-
-ifeq ($(debug),1)
-PLATFORM_CPPFLAGS += -DDEBUG
-endif
diff --git a/board/altera/ep1s40/ep1s40.c b/board/altera/ep1s40/ep1s40.c
deleted file mode 100644
index 6395de7..0000000
--- a/board/altera/ep1s40/ep1s40.c
+++ /dev/null
@@ -1,47 +0,0 @@
-/*
- * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
- * Scott McNutt <smcnutt at psyent.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <netdev.h>
-
-int checkboard (void)
-{
- puts ("BOARD : Altera EP-1S40\n");
- return 0;
-}
-
-phys_size_t initdram (int board_type)
-{
- return (0);
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_SMC91111
- rc = smc91111_initialize(0, CONFIG_SMC91111_BASE);
-#endif
- return rc;
-}
-#endif
diff --git a/boards.cfg b/boards.cfg
index e54673e..9b126a3 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -75,9 +75,6 @@ M5272C3 m68k mcf52x2 m5272c3 freescale
EP2500 m68k mcf52x2 ep2500 Mercury
purple mips mips
tb0229 mips mips
-EP1C20 nios2 nios2 ep1c20 altera
-EP1S10 nios2 nios2 ep1s10 altera
-EP1S40 nios2 nios2 ep1s40 altera
PCI5441 nios2 nios2 pci5441 psyent
PK1C20 nios2 nios2 pk1c20 psyent
P3G4 powerpc 74xx_7xx evb64260
diff --git a/include/configs/EP1C20.h b/include/configs/EP1C20.h
deleted file mode 100644
index 3920d35..0000000
--- a/include/configs/EP1C20.h
+++ /dev/null
@@ -1,214 +0,0 @@
-/*
- * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
- * Scott McNutt <smcnutt at psyent.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*------------------------------------------------------------------------
- * BOARD/CPU
- *----------------------------------------------------------------------*/
-#define CONFIG_EP1C20 1 /* EP1C20 board */
-#define CONFIG_SYS_CLK_FREQ 50000000 /* 50 MHz core clk */
-
-#define CONFIG_SYS_RESET_ADDR 0x00000000 /* Hard-reset address */
-#define CONFIG_SYS_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/
-#define CONFIG_SYS_NIOS_SYSID_BASE 0x021208b8 /* System id address */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* enable early board-spec. init*/
-
-/*------------------------------------------------------------------------
- * CACHE -- the following will support II/s and II/f. The II/s does not
- * have dcache, so the cache instructions will behave as NOPs.
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_ICACHE_SIZE 4096 /* 4 KByte total */
-#define CONFIG_SYS_ICACHELINE_SIZE 32 /* 32 bytes/line */
-#define CONFIG_SYS_DCACHE_SIZE 2048 /* 2 KByte (II/f) */
-#define CONFIG_SYS_DCACHELINE_SIZE 4 /* 4 bytes/line (II/f) */
-
-/*------------------------------------------------------------------------
- * MEMORY BASE ADDRESSES
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_BASE 0x00000000 /* FLASH base addr */
-#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */
-#define CONFIG_SYS_SDRAM_BASE 0x01000000 /* SDRAM base addr */
-#define CONFIG_SYS_SDRAM_SIZE 0x01000000 /* 16 MByte */
-#define CONFIG_SYS_SRAM_BASE 0x02000000 /* SRAM base addr */
-#define CONFIG_SYS_SRAM_SIZE 0x00100000 /* 1 MB (only 1M mapped)*/
-
-/*------------------------------------------------------------------------
- * MEMORY ORGANIZATION
- * -Monitor at top.
- * -The heap is placed below the monitor.
- * -Global data is placed below the heap.
- * -The stack is placed below global data (&grows down).
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 128k */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Global data size rsvd*/
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
-
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
-#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP CONFIG_SYS_GBL_DATA_OFFSET
-
-/*------------------------------------------------------------------------
- * FLASH (AM29LV065D)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* Max # sects per bank */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max # of flash banks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Erase timeout (msec) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 100 /* Write timeout (msec) */
-#define CONFIG_SYS_FLASH_WORD_SIZE unsigned char /* flash word size */
-
-/*------------------------------------------------------------------------
- * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
- * CONFIG_SYS_RESET_ADDR, since we assume the monitor is stored at the
- * reset address, no? This will keep the environment in user region
- * of flash. NOTE: the monitor length must be multiple of sector size
- * (which is common practice).
- *----------------------------------------------------------------------*/
-#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment in flash */
-#define CONFIG_ENV_SIZE (64 * 1024) /* 64 KByte (1 sector) */
-#define CONFIG_ENV_OVERWRITE /* Serial change Ok */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_RESET_ADDR + CONFIG_SYS_MONITOR_LEN)
-
-/*------------------------------------------------------------------------
- * CONSOLE
- *----------------------------------------------------------------------*/
-#define CONFIG_ALTERA_UART 1 /* Use altera uart */
-#if defined(CONFIG_ALTERA_JTAG_UART)
-#define CONFIG_SYS_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */
-#else
-#define CONFIG_SYS_NIOS_CONSOLE 0x02120840 /* UART base addr */
-#endif
-
-#define CONFIG_SYS_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */
-#define CONFIG_BAUDRATE 115200 /* Initial baudrate */
-#define CONFIG_SYS_BAUDRATE_TABLE {115200} /* It's fixed ;-) */
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* Suppress console info*/
-
-/*------------------------------------------------------------------------
- * EPCS Device -- wne CONFIG_SYS_NIOS_EPCSBASE is defined code/commands for
- * epcs device access is enabled. The base address is the epcs
- * _register_ base address, NOT THE ADDRESS OF THE MEMORY BLOCK.
- * The register base is currently at offset 0x600 from the memory base.
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_NIOS_EPCSBASE 0x02100200 /* EPCS register base */
-
-/*------------------------------------------------------------------------
- * DEBUG
- *----------------------------------------------------------------------*/
-#undef CONFIG_ROM_STUBS /* Stubs not in ROM */
-
-/*------------------------------------------------------------------------
- * TIMEBASE --
- *
- * The high res timer defaults to 1 msec. Since it includes the period
- * registers, the interrupt frequency can be reduced using TMRCNT.
- * If the default period is acceptable, TMRCNT can be left undefined.
- * TMRMS represents the desired mecs per tick (msecs per interrupt).
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_HZ 1000 /* Always 1000 */
-#define CONFIG_SYS_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */
-#define CONFIG_SYS_NIOS_TMRIRQ 3 /* Timer IRQ num */
-#define CONFIG_SYS_NIOS_TMRMS 10 /* Desired period (msec)*/
-#define CONFIG_SYS_NIOS_TMRCNT \
- (CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000))
-
-/*------------------------------------------------------------------------
- * STATUS LED -- Provides a simple blinking led. For Nios2 each board
- * must implement its own led routines -- leds are, after all,
- * board-specific, no?
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */
-#define CONFIG_STATUS_LED /* Enable status driver */
-
-#define STATUS_LED_BIT 1 /* Bit-0 on PIO */
-#define STATUS_LED_STATE 1 /* Blinking */
-#define STATUS_LED_PERIOD (500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec */
-
-/*------------------------------------------------------------------------
- * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ...
- * and really doesn't need any additional clutter. So I choose the lazy
- * way out to avoid changes there -- define the base address to ensure
- * cache bypass so there's no need to monkey with inx/outx macros.
- *----------------------------------------------------------------------*/
-#define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */
-#define CONFIG_NET_MULTI
-#define CONFIG_SMC91111 /* Using SMC91c111 */
-#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */
-#define CONFIG_SMC_USE_32_BIT /* 32-bit interface */
-
-#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_IPADDR 192.168.2.21
-#define CONFIG_SERVERIP 192.168.2.16
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SAVES
-
-#undef CONFIG_CMD_BOOTD
-#undef CONFIG_CMD_CONSOLE
-#undef CONFIG_CMD_FPGA
-#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_ITEST
-#undef CONFIG_CMD_NFS
-#undef CONFIG_CMD_SETGETDCR
-#undef CONFIG_CMD_SOURCE
-#undef CONFIG_CMD_XIMG
-
-
-/*------------------------------------------------------------------------
- * MISC
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LONGHELP /* Provide extended help*/
-#define CONFIG_SYS_PROMPT "==> " /* Command prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O buf size */
-#define CONFIG_SYS_MAXARGS 16 /* Max command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg buf size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */
-#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE /* Default load address */
-#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE /* Start addr for test */
-#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_INIT_SP - 0x00020000
-
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/EP1S10.h b/include/configs/EP1S10.h
deleted file mode 100644
index bfbf8c1..0000000
--- a/include/configs/EP1S10.h
+++ /dev/null
@@ -1,207 +0,0 @@
-/*
- * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
- * Scott McNutt <smcnutt at psyent.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*------------------------------------------------------------------------
- * BOARD/CPU
- *----------------------------------------------------------------------*/
-#define CONFIG_EP1S10 1 /* EP1S10 board */
-#define CONFIG_SYS_CLK_FREQ 50000000 /* 50 MHz core clk */
-
-#define CONFIG_SYS_RESET_ADDR 0x00000000 /* Hard-reset address */
-#define CONFIG_SYS_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/
-#define CONFIG_SYS_NIOS_SYSID_BASE 0x021208b8 /* System id address */
-
-/*------------------------------------------------------------------------
- * CACHE -- the following will support II/s and II/f. The II/s does not
- * have dcache, so the cache instructions will behave as NOPs.
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_ICACHE_SIZE 4096 /* 4 KByte total */
-#define CONFIG_SYS_ICACHELINE_SIZE 32 /* 32 bytes/line */
-#define CONFIG_SYS_DCACHE_SIZE 2048 /* 2 KByte (II/f) */
-#define CONFIG_SYS_DCACHELINE_SIZE 4 /* 4 bytes/line (II/f) */
-
-/*------------------------------------------------------------------------
- * MEMORY BASE ADDRESSES
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_BASE 0x00000000 /* FLASH base addr */
-#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */
-#define CONFIG_SYS_SDRAM_BASE 0x01000000 /* SDRAM base addr */
-#define CONFIG_SYS_SDRAM_SIZE 0x01000000 /* 16 MByte */
-#define CONFIG_SYS_SRAM_BASE 0x02000000 /* SRAM base addr */
-#define CONFIG_SYS_SRAM_SIZE 0x00100000 /* 1 MB */
-
-/*------------------------------------------------------------------------
- * MEMORY ORGANIZATION
- * -Monitor at top.
- * -The heap is placed below the monitor.
- * -Global data is placed below the heap.
- * -The stack is placed below global data (&grows down).
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256k */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Global data size rsvd*/
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256*1024) /* 256k heap */
-
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
-#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP CONFIG_SYS_GBL_DATA_OFFSET
-
-/*------------------------------------------------------------------------
- * FLASH (AM29LV065D)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* Max # sects per bank */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max # of flash banks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Erase timeout (msec) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 100 /* Write timeout (msec) */
-
-/*------------------------------------------------------------------------
- * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
- * CONFIG_SYS_FLASH_BASE, since we assume that u-boot is stored at the bottom
- * of flash memory. This will keep the environment in user region
- * of flash. NOTE: the monitor length must be multiple of sector size
- * (which is common practice).
- *----------------------------------------------------------------------*/
-#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment in flash */
-#define CONFIG_ENV_SIZE (64 * 1024) /* 64 KByte (1 sector) */
-#define CONFIG_ENV_OVERWRITE /* Serial change Ok */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
-
-/*------------------------------------------------------------------------
- * CONSOLE
- *----------------------------------------------------------------------*/
-#define CONFIG_ALTERA_UART 1 /* Use altera uart */
-#if defined(CONFIG_ALTERA_JTAG_UART)
-#define CONFIG_SYS_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */
-#else
-#define CONFIG_SYS_NIOS_CONSOLE 0x02120840 /* UART base addr */
-#endif
-
-#define CONFIG_SYS_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */
-#define CONFIG_BAUDRATE 115200 /* Initial baudrate */
-#define CONFIG_SYS_BAUDRATE_TABLE {115200} /* It's fixed ;-) */
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* Suppress console info*/
-
-/*------------------------------------------------------------------------
- * EPCS Device -- None for stratix.
- *----------------------------------------------------------------------*/
-#undef CONFIG_SYS_NIOS_EPCSBASE
-
-/*------------------------------------------------------------------------
- * DEBUG
- *----------------------------------------------------------------------*/
-#undef CONFIG_ROM_STUBS /* Stubs not in ROM */
-
-/*------------------------------------------------------------------------
- * TIMEBASE --
- *
- * The high res timer defaults to 1 msec. Since it includes the period
- * registers, the interrupt frequency can be reduced using TMRCNT.
- * If the default period is acceptable, TMRCNT can be left undefined.
- * TMRMS represents the desired mecs per tick (msecs per interrupt).
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_HZ 1000 /* Always 1000 */
-#define CONFIG_SYS_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */
-#define CONFIG_SYS_NIOS_TMRIRQ 3 /* Timer IRQ num */
-#define CONFIG_SYS_NIOS_TMRMS 10 /* Desired period (msec)*/
-#define CONFIG_SYS_NIOS_TMRCNT \
- (CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000))
-
-/*------------------------------------------------------------------------
- * STATUS LED -- Provides a simple blinking led. For Nios2 each board
- * must implement its own led routines -- since leds are board-specific.
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */
-#define CONFIG_STATUS_LED /* Enable status driver */
-
-#define STATUS_LED_BIT 1 /* Bit-0 on PIO */
-#define STATUS_LED_STATE 1 /* Blinking */
-#define STATUS_LED_PERIOD (500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec */
-
-/*------------------------------------------------------------------------
- * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ...
- * and really doesn't need any additional clutter. So I choose the lazy
- * way out to avoid changes there -- define the base address to ensure
- * cache bypass so there's no need to monkey with inx/outx macros.
- *----------------------------------------------------------------------*/
-#define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */
-#define CONFIG_NET_MULTI
-#define CONFIG_SMC91111 /* Using SMC91c111 */
-#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */
-#define CONFIG_SMC_USE_32_BIT /* 32-bit interface */
-
-#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_IPADDR 192.168.2.21
-#define CONFIG_SERVERIP 192.168.2.16
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_BDI
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_LOADS
-#define CONFIG_CMD_LOADB
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_MISC
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_RUN
-#define CONFIG_CMD_SAVES
-
-
-/*------------------------------------------------------------------------
- * MISC
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LONGHELP /* Provide extended help*/
-#define CONFIG_SYS_PROMPT "==> " /* Command prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O buf size */
-#define CONFIG_SYS_MAXARGS 16 /* Max command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg buf size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */
-#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE /* Default load address */
-#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE /* Start addr for test */
-#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_INIT_SP - 0x00020000
-
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/EP1S40.h b/include/configs/EP1S40.h
deleted file mode 100644
index 4d905fe..0000000
--- a/include/configs/EP1S40.h
+++ /dev/null
@@ -1,207 +0,0 @@
-/*
- * (C) Copyright 2005, Psyent Corporation <www.psyent.com>
- * Scott McNutt <smcnutt at psyent.com>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*------------------------------------------------------------------------
- * BOARD/CPU
- *----------------------------------------------------------------------*/
-#define CONFIG_EP1S40 1 /* EP1S40 board */
-#define CONFIG_SYS_CLK_FREQ 50000000 /* 50 MHz core clk */
-
-#define CONFIG_SYS_RESET_ADDR 0x00000000 /* Hard-reset address */
-#define CONFIG_SYS_EXCEPTION_ADDR 0x01000020 /* Exception entry point*/
-#define CONFIG_SYS_NIOS_SYSID_BASE 0x021208b8 /* System id address */
-
-/*------------------------------------------------------------------------
- * CACHE -- the following will support II/s and II/f. The II/s does not
- * have dcache, so the cache instructions will behave as NOPs.
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_ICACHE_SIZE 4096 /* 4 KByte total */
-#define CONFIG_SYS_ICACHELINE_SIZE 32 /* 32 bytes/line */
-#define CONFIG_SYS_DCACHE_SIZE 2048 /* 2 KByte (II/f) */
-#define CONFIG_SYS_DCACHELINE_SIZE 4 /* 4 bytes/line (II/f) */
-
-/*------------------------------------------------------------------------
- * MEMORY BASE ADDRESSES
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_FLASH_BASE 0x00000000 /* FLASH base addr */
-#define CONFIG_SYS_FLASH_SIZE 0x00800000 /* 8 MByte */
-#define CONFIG_SYS_SDRAM_BASE 0x01000000 /* SDRAM base addr */
-#define CONFIG_SYS_SDRAM_SIZE 0x01000000 /* 16 MByte */
-#define CONFIG_SYS_SRAM_BASE 0x02000000 /* SRAM base addr */
-#define CONFIG_SYS_SRAM_SIZE 0x00100000 /* 1 MB */
-
-/*------------------------------------------------------------------------
- * MEMORY ORGANIZATION
- * -Monitor at top.
- * -The heap is placed below the monitor.
- * -Global data is placed below the heap.
- * -The stack is placed below global data (&grows down).
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256k */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Global data size rsvd*/
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 256*1024) /* 256k heap */
-
-#define CONFIG_SYS_MONITOR_BASE TEXT_BASE
-#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP CONFIG_SYS_GBL_DATA_OFFSET
-
-/*------------------------------------------------------------------------
- * FLASH (AM29LV065D)
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_MAX_FLASH_SECT 128 /* Max # sects per bank */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max # of flash banks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Erase timeout (msec) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 100 /* Write timeout (msec) */
-
-/*------------------------------------------------------------------------
- * ENVIRONMENT -- Put environment in sector CONFIG_SYS_MONITOR_LEN above
- * CONFIG_SYS_FLASH_BASE, since we assume that u-boot is stored at the bottom
- * of flash memory. This will keep the environment in user region
- * of flash. NOTE: the monitor length must be multiple of sector size
- * (which is common practice).
- *----------------------------------------------------------------------*/
-#define CONFIG_ENV_IS_IN_FLASH 1 /* Environment in flash */
-#define CONFIG_ENV_SIZE (64 * 1024) /* 64 KByte (1 sector) */
-#define CONFIG_ENV_OVERWRITE /* Serial change Ok */
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN)
-
-/*------------------------------------------------------------------------
- * CONSOLE
- *----------------------------------------------------------------------*/
-#define CONFIG_ALTERA_UART 1 /* Use altera uart */
-#if defined(CONFIG_ALTERA_JTAG_UART)
-#define CONFIG_SYS_NIOS_CONSOLE 0x021208b0 /* JTAG UART base addr */
-#else
-#define CONFIG_SYS_NIOS_CONSOLE 0x02120840 /* UART base addr */
-#endif
-
-#define CONFIG_SYS_NIOS_FIXEDBAUD 1 /* Baudrate is fixed */
-#define CONFIG_BAUDRATE 115200 /* Initial baudrate */
-#define CONFIG_SYS_BAUDRATE_TABLE {115200} /* It's fixed ;-) */
-
-#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* Suppress console info*/
-
-/*------------------------------------------------------------------------
- * EPCS Device -- None for stratix.
- *----------------------------------------------------------------------*/
-#undef CONFIG_SYS_NIOS_EPCSBASE
-
-/*------------------------------------------------------------------------
- * DEBUG
- *----------------------------------------------------------------------*/
-#undef CONFIG_ROM_STUBS /* Stubs not in ROM */
-
-/*------------------------------------------------------------------------
- * TIMEBASE --
- *
- * The high res timer defaults to 1 msec. Since it includes the period
- * registers, the interrupt frequency can be reduced using TMRCNT.
- * If the default period is acceptable, TMRCNT can be left undefined.
- * TMRMS represents the desired mecs per tick (msecs per interrupt).
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_HZ 1000 /* Always 1000 */
-#define CONFIG_SYS_NIOS_TMRBASE 0x02120820 /* Tick timer base addr */
-#define CONFIG_SYS_NIOS_TMRIRQ 3 /* Timer IRQ num */
-#define CONFIG_SYS_NIOS_TMRMS 10 /* Desired period (msec) */
-#define CONFIG_SYS_NIOS_TMRCNT \
- (CONFIG_SYS_NIOS_TMRMS * (CONFIG_SYS_CLK_FREQ/1000))
-
-/*------------------------------------------------------------------------
- * STATUS LED -- Provides a simple blinking led. For Nios2 each board
- * must implement its own led routines -- since leds are board-specific.
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LEDPIO_ADDR 0x02120870 /* LED PIO base addr */
-#define CONFIG_STATUS_LED /* Enable status driver */
-
-#define STATUS_LED_BIT 1 /* Bit-0 on PIO */
-#define STATUS_LED_STATE 1 /* Blinking */
-#define STATUS_LED_PERIOD (500/CONFIG_SYS_NIOS_TMRMS) /* Every 500 msec */
-
-/*------------------------------------------------------------------------
- * ETHERNET -- The header file for the SMC91111 driver hurts my eyes ...
- * and really doesn't need any additional clutter. So I choose the lazy
- * way out to avoid changes there -- define the base address to ensure
- * cache bypass so there's no need to monkey with inx/outx macros.
- *----------------------------------------------------------------------*/
-#define CONFIG_SMC91111_BASE 0x82110300 /* Base addr (bypass) */
-#define CONFIG_NET_MULTI
-#define CONFIG_SMC91111 /* Using SMC91c111 */
-#undef CONFIG_SMC91111_EXT_PHY /* Internal PHY */
-#define CONFIG_SMC_USE_32_BIT /* 32-bit interface */
-
-#define CONFIG_ETHADDR 08:00:3e:26:0a:5b
-#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_IPADDR 192.168.2.21
-#define CONFIG_SERVERIP 192.168.2.16
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_BDI
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_SAVEENV
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_LOADS
-#define CONFIG_CMD_LOADB
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_MISC
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_RUN
-#define CONFIG_CMD_SAVES
-
-
-/*------------------------------------------------------------------------
- * MISC
- *----------------------------------------------------------------------*/
-#define CONFIG_SYS_LONGHELP /* Provide extended help*/
-#define CONFIG_SYS_PROMPT "==> " /* Command prompt */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O buf size */
-#define CONFIG_SYS_MAXARGS 16 /* Max command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot arg buf size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buf size */
-#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE /* Default load address */
-#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE /* Start addr for test */
-#define CONFIG_SYS_MEMTEST_END CONFIG_SYS_INIT_SP - 0x00020000
-
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-#endif /* __CONFIG_H */
--
1.7.1.86.g0e460
More information about the U-Boot
mailing list