[U-Boot] [PATCH v2 09/17] tegra: usb: fdt: Add additional device tree definitions for USB ports

Simon Glass sjg at chromium.org
Thu Dec 8 22:10:58 CET 2011


Hi Stephen,

On Wed, Dec 7, 2011 at 3:36 PM, Stephen Warren <swarren at nvidia.com> wrote:
> On 12/06/2011 02:09 PM, Simon Glass wrote:
>> On Tue, Dec 6, 2011 at 12:28 PM, Stephen Warren <swarren at nvidia.com> wrote:
>>> On 12/05/2011 05:55 PM, Simon Glass wrote:
>>>> On Mon, Dec 5, 2011 at 3:25 PM, Stephen Warren <swarren at nvidia.com> wrote:
>>>>> On 12/02/2011 07:11 PM, Simon Glass wrote:
>>>>>> This adds peripheral IDs and timing information to the USB part of the
>>>>>> device tree for U-Boot.
>>>>>>
>>>>>> The peripheral IDs provide easy access to clock registers. We will likely
>>>>>> remove this in favor of a full clock tree when it is available in the
>>>>>> kernel (but probably still retain the peripheral ID, just move it into
>>>>>> a clock node).
>>>>>>
>>>>>> The USB timing information does apparently vary between boards sometimes,
>>>>>> so is include in the fdt for convenience.
>
>>>>>>       usb at c5000000 {
>>>>>>               compatible = "nvidia,tegra20-ehci", "usb-ehci";
>>>>>>               reg = <0xc5000000 0x4000>;
>>>>>>               interrupts = < 52 >;
>>>>>>               phy_type = "utmi";
>>>>>> +             periph-id = <22>;       // PERIPH_ID_USBD
>>>>>
>>>>> Given this is a temporary U-Boot-specific solution, can the property be
>>>>> named u-boot,periph-id so it's obvious that when writing a .dts for the
>>>>> kernel only, you don't care about this value.
>>>>
>>>> ok. I suggest the kernel does something similar.
>>>
>>> The kernel will use the standardized clock bindings once they're ready
>>> and we convert Tegra over to use them. The kernel is extremely unlikely
>>> to ever use "periph-id" or "u-boot,periph-id".
>>
>> What is the time frame on this working be completed and merged?
>
> Sorry, I have no idea. I've been focusing on other subsystems (pinmux,
> audio) and haven't been following the clock stuff at all. Hopefully
> someone will start driving Tegra kernel towards common clock soon, but I
> don't think exactly who and when has been nailed down yet.
>
>>> Right now, the kernel's clock driver contains a mapping table from
>>> device name (e.g. tegra-ehci.2) to clock name (e.g. usb3). This allows
>>> the kernel USB driver to work without any explicit periph-id or similar
>>> DT property.
>>
>> Where does tegra-ehci.2 come from? I don't see that in the fdt.
>
> Pre-DT, everything was instantiated from platform devices. Each one had
> a name ("tegra-ehci") and an instance number ("2"), which concatenate to
> "tegra-ehci.2". All the clocks (and I think other resources like
> regulators) in the kernel were marked as being for use by a particular
> device name. For example in arch/arm/mach-tegra/tegra2_clocks.c:
>
> static struct clk tegra_list_clks[] = {
> ...
>        PERIPH_CLK("usb3",      "tegra-ehci.2", ...),
>
> With DT, the device names typically don't follow this format (in this
> case, it'd be something more like "/usb at c5008000"). However, this
> prevented the clock lookups by device name from working, so a temporary
> scheme was put in place to keep the same device names. This is driven by
> "AUXDATA", for example in arch/arm/mach-tegra/board-dt.c:
>
>
> struct of_dev_auxdata tegra20_auxdata_lookup[] __initdata = {
> ...
> //             compatible, unit address, device name
> OF_DEV_AUXDATA("nvidia,tegra20-ehci", TEGRA_USB3_BASE, "tegra-ehci.2",
>
> This means that any device with the given compatible property value, the
> given unit address will be named accordingly.
>
> This allows the existing clock/regulator lookups to work unmodified.
>
> Once DT bindings are in place for clocks, regulators, etc., the clock
> tables can be derived from DT, phandles will be used to match clocks and
> devices rather than device names, and the AUXDATA table can go away.
>
> The equivalent in U-Boot would be a table that maps from driver type
> (e.g. COMPAT_NVIDIA_TEGRA20_USB or perhaps NVIDIA_TEGRA20_USB?) and
> address to periph id. Again, once the clock bindings are complete and
> the nodes present in the .dts file, that mapping table can be removed
> and everything will work based on phandles.
>
> I'd like to point out here that everything is in a pretty big state of
> flux/development, since DT support for ARM is new. Temporary workarounds
> like AUXDATA allow us to make as much work as possible using device
> tree, but without having to put temporary nodes/properties into the .dts
> files themselves. That way, the DT bindings will only ever get added to
> in a compatible fashion, rather than going through multiple incompatible
> sets of requirements.

Gosh.

I have to say that I feel that peripheral IDs are the best solution
for Tegra U-Boot until everything is worked out in the kernel.

We can't rely on phandles since they don't exist without an fdt,
unless we mandate that everyone must use an fdt. I don't feel
comfortable doing that until things are a bit more stable with all the
things you are working on.

I really can't see why we want to put a table in U-Boot which does a
mapping that is clear a hardware feature and IMO belongs in the fdt
(why repeat peripheral addresses in the code and the fdt?).

Plus I still don't have an answer to my question about how we can
ensure that instance 0 is a particular device. The fact that this just
happens to work in the kernel for uarts, and shouldn't matter for
everything else, is not good enough in U-Boot since scripts etc. rely
on instance mapping being stable.

So for now I think we should simply add a peripheral ID to the fdt,
use the alias mechanism (perhaps augmented by scanning peripherals not
mentioned by an alias if you like) and be done with it.

Regards,
Simon

>
> --
> nvpublic


More information about the U-Boot mailing list