[U-Boot] Please pull u-boot-imx/next into arm/next

Stefano Babic sbabic at denx.de
Mon Sep 26 13:35:19 CEST 2011


Hi Albert,

please pull u-boot-imx/next (already rebased on u-boot-arm/next after
you merged u-boot-ti) into your u-boot-arm/next.

Best regards,
Stefano

The following changes since commit f3340eeaf574b3297e801a563089c90d23e84f8d:

  arm, davinci, da8xx: add cpuinfo (2011-09-23 15:50:39 -0400)

are available in the git repository at:
  git://www.denx.de/git/u-boot-imx.git next

Fabio Estevam (25):
      ARM: mx25: Print the silicon revison
      ARM: mx25: Print the source of reset
      MX31: mx31pdk: Remove nand_spl config.mk file
      MX31: Improve readability for reset cause
      mx31pdk: Change the prompt as per other i.MX boards
      MX25: tx25: Avoid the usage of extern in C file
      MX25: Add initial support for MX25PDK
      MX31: Disable watchdog during low-power modes
      mx31pdk: Remove dram_init_banksize()
      mx25pdk: Remove dram_init_banksize()
      mx31ads: Remove dram_init_banksize()
      imx31_litekit: Remove dram_init_banksize()
      mx31pdk: Place machine ID into board config
      mx25pdk: Place machine ID into board config
      mx31ads: Place machine ID into board config
      imx31_litekit: Place machine ID into board config
      mx51evk: Place machine ID into board config
      mx53loco: Place machine ID into board config
      mx53smd: Place machine ID into board config
      mx53ard: Place machine ID into board config
      mx53evk: Place machine ID into board config
      zmx25: Remove dram_init_banksize()
      zmx25: Place machine ID into board config
      zmx25: Fix build warning due to 'get_reset_cause' defined but not used
      vision2: Place machine ID into board config

Jason Liu (1):
      cosmetic: fsl_pmic: cosmetic for the help message

Marek Vasut (19):
      EfikaMX: Adjust undocumented magic constant in config file
      FEC: Use proper accessor to read register in debug call
      FEC: Use defined constant instead of magic number
      FEC: Kill mode select FIXME's
      FEC: Add RMII mode support
      FEC: Allow selection of MII mode via CONFIG_FEC_XCV_TYPE
      FEC: Abstract access to fec->eth in MII operations
      FEC: Allow multiple FECes
      FEC: Allow registering MII postconfiguration callback
      FEC: Add timeout for chip reset
      FEC: Squish "got MAC from fuse" message, make it debug()
      FEC: Move imx_get_mac_from_fuse() definition to fec_mxc.h
      MX5: Modify the PLL decoding algorithm
      MX5: Add AHB clock reporting and fix IPG clock reporting
      MX5: Clean up the output of "clocks" command
      I2C: mxc_i2c rework
      ATA: Squash warnings in mxc_ata.
      EfikaMX: Add imximage config for Efika SB
      EfikaSB: Add preliminary EfikaSB support

 MAINTAINERS                                     |    2 +
 arch/arm/cpu/arm1136/mx31/generic.c             |    2 +-
 arch/arm/cpu/arm1136/mx31/timer.c               |    4 +-
 arch/arm/cpu/arm926ejs/mx25/generic.c           |   53 +++-
 arch/arm/cpu/armv7/mx5/clock.c                  |  114 +++++--
 arch/arm/include/asm/arch-mx25/imx-regs.h       |    4 +-
 arch/arm/include/asm/arch-mx25/sys_proto.h      |   29 ++
 arch/arm/include/asm/arch-mx27/imx-regs.h       |    1 -
 arch/arm/include/asm/arch-mx31/imx-regs.h       |    2 +
 arch/arm/include/asm/arch-mx35/imx-regs.h       |    2 -
 arch/arm/include/asm/arch-mx5/crm_regs.h        |   11 +
 arch/arm/include/asm/arch-mx5/imx-regs.h        |    5 +-
 board/efikamx/efikamx.c                         |  124 ++++++--
 board/efikamx/{imximage.cfg => imximage_mx.cfg} |    0
 board/efikamx/{imximage.cfg => imximage_sb.cfg} |   26 +-
 board/freescale/mx25pdk/Makefile                |   49 +++
 board/freescale/mx25pdk/imximage.cfg            |   73 ++++
 board/freescale/mx25pdk/lowlevel_init.S         |   21 ++
 board/freescale/mx25pdk/mx25pdk.c               |   56 +++
 board/freescale/mx31ads/mx31ads.c               |    7 -
 board/freescale/mx31pdk/mx31pdk.c               |    7 -
 board/freescale/mx51evk/mx51evk.c               |    1 -
 board/freescale/mx53ard/mx53ard.c               |    1 -
 board/freescale/mx53evk/mx53evk.c               |    1 -
 board/freescale/mx53loco/mx53loco.c             |    1 -
 board/freescale/mx53smd/mx53smd.c               |    1 -
 board/karo/tx25/tx25.c                          |    3 +-
 board/logicpd/imx31_litekit/imx31_litekit.c     |    7 -
 board/syteco/zmx25/zmx25.c                      |    8 -
 board/ttcontrol/vision2/vision2.c               |    1 -
 boards.cfg                                      |    5 +-
 drivers/block/mxc_ata.c                         |   22 +-
 drivers/i2c/mxc_i2c.c                           |  422
++++++++++++++++-------
 drivers/misc/fsl_pmic.c                         |    2 +-
 drivers/net/fec_mxc.c                           |  170 ++++++---
 drivers/net/fec_mxc.h                           |    9 +-
 include/configs/efikamx.h                       |    6 +-
 include/configs/imx31_litekit.h                 |    4 +-
 include/configs/mx25pdk.h                       |  108 ++++++
 include/configs/mx31ads.h                       |    2 +
 include/configs/mx31pdk.h                       |    4 +-
 include/configs/mx51evk.h                       |    1 +
 include/configs/mx53ard.h                       |    2 +
 include/configs/mx53evk.h                       |    2 +
 include/configs/mx53loco.h                      |    2 +
 include/configs/mx53smd.h                       |    4 +-
 include/configs/vision2.h                       |    2 +
 include/configs/zmx25.h                         |    1 +
 include/netdev.h                                |    7 +-
 nand_spl/board/freescale/mx31pdk/Makefile       |    2 +-
 nand_spl/board/freescale/mx31pdk/config.mk      |    1 -
 51 files changed, 1073 insertions(+), 321 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-mx25/sys_proto.h
 copy board/efikamx/{imximage.cfg => imximage_mx.cfg} (100%)
 rename board/efikamx/{imximage.cfg => imximage_sb.cfg} (90%)
 create mode 100644 board/freescale/mx25pdk/Makefile
 create mode 100644 board/freescale/mx25pdk/imximage.cfg
 create mode 100644 board/freescale/mx25pdk/lowlevel_init.S
 create mode 100644 board/freescale/mx25pdk/mx25pdk.c
 create mode 100644 include/configs/mx25pdk.h
 delete mode 100644 nand_spl/board/freescale/mx31pdk/config.mk

-- 
=====================================================================
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80  Email: office at denx.de
=====================================================================


More information about the U-Boot mailing list