[U-Boot] Please pull u-boot-imx/next into arm/next

[Albert ARIBAUD]

Hi Stefano,

On 26/09/2011 13:35, Stefano Babic wrote:
> Hi Albert,
>
> please pull u-boot-imx/next (already rebased on u-boot-arm/next after
> you merged u-boot-ti) into your u-boot-arm/next.
>
> Best regards,
> Stefano
>
> The following changes since commit f3340eeaf574b3297e801a563089c90d23e84f8d:
>
>    arm, davinci, da8xx: add cpuinfo (2011-09-23 15:50:39 -0400)
>
> are available in the git repository at:
>    git://www.denx.de/git/u-boot-imx.git next
>
> Fabio Estevam (25):
>        ARM: mx25: Print the silicon revison
>        ARM: mx25: Print the source of reset
>        MX31: mx31pdk: Remove nand_spl config.mk file
>        MX31: Improve readability for reset cause
>        mx31pdk: Change the prompt as per other i.MX boards
>        MX25: tx25: Avoid the usage of extern in C file
>        MX25: Add initial support for MX25PDK
>        MX31: Disable watchdog during low-power modes
>        mx31pdk: Remove dram_init_banksize()
>        mx25pdk: Remove dram_init_banksize()
>        mx31ads: Remove dram_init_banksize()
>        imx31_litekit: Remove dram_init_banksize()
>        mx31pdk: Place machine ID into board config
>        mx25pdk: Place machine ID into board config
>        mx31ads: Place machine ID into board config
>        imx31_litekit: Place machine ID into board config
>        mx51evk: Place machine ID into board config
>        mx53loco: Place machine ID into board config
>        mx53smd: Place machine ID into board config
>        mx53ard: Place machine ID into board config
>        mx53evk: Place machine ID into board config
>        zmx25: Remove dram_init_banksize()
>        zmx25: Place machine ID into board config
>        zmx25: Fix build warning due to 'get_reset_cause' defined but not used
>        vision2: Place machine ID into board config
>
> Jason Liu (1):
>        cosmetic: fsl_pmic: cosmetic for the help message
>
> Marek Vasut (19):
>        EfikaMX: Adjust undocumented magic constant in config file
>        FEC: Use proper accessor to read register in debug call
>        FEC: Use defined constant instead of magic number
>        FEC: Kill mode select FIXME's
>        FEC: Add RMII mode support
>        FEC: Allow selection of MII mode via CONFIG_FEC_XCV_TYPE
>        FEC: Abstract access to fec->eth in MII operations
>        FEC: Allow multiple FECes
>        FEC: Allow registering MII postconfiguration callback
>        FEC: Add timeout for chip reset
>        FEC: Squish "got MAC from fuse" message, make it debug()
>        FEC: Move imx_get_mac_from_fuse() definition to fec_mxc.h
>        MX5: Modify the PLL decoding algorithm
>        MX5: Add AHB clock reporting and fix IPG clock reporting
>        MX5: Clean up the output of "clocks" command
>        I2C: mxc_i2c rework
>        ATA: Squash warnings in mxc_ata.
>        EfikaMX: Add imximage config for Efika SB
>        EfikaSB: Add preliminary EfikaSB support

Applied to u-boot-arm/next, thanks!

Amicalement,
-- 
Albert.