[U-Boot] [PATCH v7] kirkwood: add NAS62x0 board support
Luka Perkov
uboot at lukaperkov.net
Sat Apr 14 19:25:32 CEST 2012
Add support for new boards RaidSonic ICY BOX NAS6210 and NAS6220.
NAS6210 has 1 SATA and 1 eSATA port while NAS6220 has 2 SATA ports.
More information about the boards can be found here:
http://www.raidsonic.de/en/products/nas-systems.php?we_objectID=7036
http://www.raidsonic.de/en/products/nas-systems.php?we_objectID=7515
Signed-off-by: Luka Perkov <uboot at lukaperkov.net>
Signed-off-by: Gerald Kerma <dreagle at doukki.net>
Signed-off-by: Simon Baatz <gmbnomis at gmail.com>
---
Changes from version v1:
* use tools/checkpatch.pl to locate patch errors and fix them
* add two entries in boards.cfg, one for each board
* fixed CONFIG_RESET_PHY_R
* don't define values for macros that enable features only
* remove static RAM configuration
* fix comments
* use only CONFIG_ENV_OFFSET and remove CONFIG_ENV_ADDR
* clean coding style
* add entry in MAINTAINERS file
Changes from version v2:
* use defined() in macros for board selection for robustness
Changes from version v3:
* don't use utf8 for Geralds name
* don't mix upper/lower case in kwbimage.cfg
* fix prompt
Changes from version v4:
* fix board Makefile (clean and distclean)
* use generic way to handle arch number of the board
* fix MAINTAINERS file
* move code from Marvell to raidsonic folder
* use CONFIG_MACH_TYPE
* set only necessary GPIOs
* use link instead of address for license
* add few links about board being supported for quick reference
* add previous change logs
* multiple updates to kwbimage.cfg, thank you Simon
Changes from version v5:
* remove typo from kwbimage.cfg (duplicated lines), thank you David
* clean up comments in kwbimage.cfg
Changes from version v6:
* replace KW_SATA_PORT0_OFFSET with MV_SATA_PORT0_OFFSET
* change commit message
NAS6210 eSATA port is not working from uboot... That is why there are
CONFIG_BOARD_IS_IB_NAS6210 and CONFIG_BOARD_IS_IB_NAS6220 in ib62x0.h
config file.
Any chance to push this in 2012.04 release?
MAINTAINERS | 5 +
board/raidsonic/ib62x0/Makefile | 43 +++++++++
board/raidsonic/ib62x0/ib62x0.c | 79 ++++++++++++++++
board/raidsonic/ib62x0/ib62x0.h | 40 ++++++++
board/raidsonic/ib62x0/kwbimage.cfg | 169 ++++++++++++++++++++++++++++++++++
boards.cfg | 2 +
include/configs/ib62x0.h | 173 +++++++++++++++++++++++++++++++++++
7 files changed, 511 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 72f8b64..e6608ea 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -781,6 +781,11 @@ Linus Walleij <linus.walleij at linaro.org>
integratorap various
integratorcp various
+Luka Perkov <uboot at lukaperkov.net>
+
+ ib6210 ARM926EJS
+ ib6220 ARM926EJS
+
Dave Peverley <dpeverley at mpc-data.co.uk>
omap730p2 ARM926EJS
diff --git a/board/raidsonic/ib62x0/Makefile b/board/raidsonic/ib62x0/Makefile
new file mode 100644
index 0000000..d450f8d
--- /dev/null
+++ b/board/raidsonic/ib62x0/Makefile
@@ -0,0 +1,43 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program. If not, see <http://www.gnu.org/licenses/>.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+COBJS := ib62x0.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/raidsonic/ib62x0/ib62x0.c b/board/raidsonic/ib62x0/ib62x0.c
new file mode 100644
index 0000000..65f2c2e
--- /dev/null
+++ b/board/raidsonic/ib62x0/ib62x0.c
@@ -0,0 +1,79 @@
+/*
+ * Copyright (C) 2011-2012
+ * Gerald Kerma <dreagle at doukki.net>
+ * Luka Perkov <uboot at lukaperkov.net>
+ * Simon Baatz <gmbnomis at gmail.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "ib62x0.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(IB62x0_OE_VAL_LOW,
+ IB62x0_OE_VAL_HIGH,
+ IB62x0_OE_LOW, IB62x0_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_SATA1_ACTn,
+ MPP21_SATA0_ACTn,
+ MPP22_GPIO, /* Power LED red */
+ MPP24_GPIO, /* Power off device */
+ MPP25_GPIO, /* Power LED green */
+ MPP27_GPIO, /* USB transfer LED */
+ MPP28_GPIO, /* Reset button */
+ MPP29_GPIO, /* USB Copy button */
+ 0
+ };
+ kirkwood_mpp_conf(kwmpp_config);
+ return 0;
+}
+
+int board_init(void)
+{
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+ return 0;
+}
diff --git a/board/raidsonic/ib62x0/ib62x0.h b/board/raidsonic/ib62x0/ib62x0.h
new file mode 100644
index 0000000..0c30690
--- /dev/null
+++ b/board/raidsonic/ib62x0/ib62x0.h
@@ -0,0 +1,40 @@
+/*
+ * Copyright (C) 2011-2012
+ * Gerald Kerma <dreagle at doukki.net>
+ * Simon Baatz <gmbnomis at gmail.com>
+ * Luka Perkov <uboot at lukaperkov.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef __IB62x0_H
+#define __IB62x0_H
+
+#define IB62x0_OE_LOW (~(1 << 22 | 1 << 24 | 1 << 25 | 1 << 27))
+#define IB62x0_OE_HIGH (~(0))
+#define IB62x0_OE_VAL_LOW 0
+#define IB62x0_OE_VAL_HIGH 0
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG 10
+#define MV88E1116_CPRSP_CR3_REG 21
+#define MV88E1116_MAC_CTRL_REG 21
+#define MV88E1116_PGADR_REG 22
+#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
+
+#endif /* __IB62x0_H */
diff --git a/board/raidsonic/ib62x0/kwbimage.cfg b/board/raidsonic/ib62x0/kwbimage.cfg
new file mode 100644
index 0000000..bd594eb
--- /dev/null
+++ b/board/raidsonic/ib62x0/kwbimage.cfg
@@ -0,0 +1,169 @@
+#
+# Copyright (C) 2011-2012
+# Gerald Kerma <dreagle at doukki.net>
+# Simon Baatz <gmbnomis at gmail.com>
+# Luka Perkov <uboot at lukaperkov.net>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program. If not, see <http://www.gnu.org/licenses/>.
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM nand # change from nand to uart if building UART image
+NAND_ECC_MODE default
+NAND_PAGE_SIZE 0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xffd100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=5 @ 400MHz
+DATA 0xffd01400 0x43000c30 # DDR Configuration register
+# bit13-0: 0xc30, (3120 DDR2 clks refresh rate)
+# bit23-14: 0x0,
+# bit24: 0x1, enable exit self refresh mode on DDR access
+# bit25: 0x1, required
+# bit29-26: 0x0,
+# bit31-30: 0x1,
+
+DATA 0xffd01404 0x37543000 # DDR Controller Control Low
+# bit4: 0x0, addr/cmd in smame cycle
+# bit5: 0x0, clk is driven during self refresh, we don't care for APX
+# bit6: 0x0, use recommended falling edge of clk for addr/cmd
+# bit14: 0x0, input buffer always powered up
+# bit18: 0x1, cpu lock transaction enabled
+# bit23-20: 0x5, recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
+# bit27-24: 0x7, CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
+# bit30-28: 0x3, required
+# bit31: 0x0, no additional STARTBURST delay
+
+DATA 0xffd01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
+# bit3-0: TRAS lsbs
+# bit7-4: TRCD
+# bit11-8: TRP
+# bit15-12: TWR
+# bit19-16: TWTR
+# bit20: TRAS msb
+# bit23-21: 0x0
+# bit27-24: TRRD
+# bit31-28: TRTP
+
+DATA 0xffd0140c 0x00000a33 # DDR Timing (High)
+# bit6-0: TRFC
+# bit8-7: TR2R
+# bit10-9: TR2W
+# bit12-11: TW2W
+# bit31-13: 0x0, required
+
+DATA 0xffd01410 0x0000000c # DDR Address Control
+# bit1-0: 00, Cs0width (x8)
+# bit3-2: 11, Cs0size (1Gb)
+# bit5-4: 00, Cs1width (x8)
+# bit7-6: 11, Cs1size (1Gb)
+# bit9-8: 00, Cs2width (nonexistent
+# bit11-10: 00, Cs2size (nonexistent
+# bit13-12: 00, Cs3width (nonexistent
+# bit15-14: 00, Cs3size (nonexistent
+# bit16: 0, Cs0AddrSel
+# bit17: 0, Cs1AddrSel
+# bit18: 0, Cs2AddrSel
+# bit19: 0, Cs3AddrSel
+# bit31-20: 0x0, required
+
+DATA 0xffd01414 0x00000000 # DDR Open Pages Control
+# bit0: 0, OpenPage enabled
+# bit31-1: 0x0, required
+
+DATA 0xffd01418 0x00000000 # DDR Operation
+# bit3-0: 0x0, DDR cmd
+# bit31-4: 0x0, required
+
+DATA 0xffd0141c 0x00000c52 # DDR Mode
+# bit2-0: 0x2, BurstLen=2 required
+# bit3: 0x0, BurstType=0 required
+# bit6-4: 0x4, CL=5
+# bit7: 0x0, TestMode=0 normal
+# bit8: 0x0, DLL reset=0 normal
+# bit11-9: 0x6, auto-precharge write recovery ????????????
+# bit12: 0x0, PD must be zero
+# bit31-13: 0x0, required
+
+DATA 0xffd01420 0x00000040 # DDR Extended Mode
+# bit0: 0, DDR DLL enabled
+# bit1: 0, DDR drive strenght normal
+# bit2: 1, DDR ODT control lsd (disabled)
+# bit5-3: 0x0, required
+# bit6: 0, DDR ODT control msb, (disabled)
+# bit9-7: 0x0, required
+# bit10: 0, differential DQS enabled
+# bit11: 0, required
+# bit12: 0, DDR output buffer enabled
+# bit31-13: 0x0, required
+
+DATA 0xffd01424 0x0000f17f # DDR Controller Control High
+# bit2-0: 0x7, required
+# bit3: 0x1, MBUS Burst Chop disabled
+# bit6-4: 0x7, required
+# bit7: 0x0,
+# bit8: 0x1, add writepath sample stage, must be 1 for DDR freq >= 300MHz
+# bit9: 0x0, no half clock cycle addition to dataout
+# bit10: 0x0, 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11: 0x0, 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 0xf, required
+# bit31-16: 0, required
+
+DATA 0xffd01428 0x00085520 # DDR2 ODT Read Timing (default values)
+DATA 0xffd0147c 0x00008552 # DDR2 ODT Write Timing (default values)
+
+DATA 0xffd01500 0x00000000 # CS[0]n Base address to 0x0
+DATA 0xffd01504 0x0ffffff1 # CS[0]n Size
+# bit0: 0x1, Window enabled
+# bit1: 0x0, Write Protect disabled
+# bit3-2: 0x0, CS0 hit selected
+# bit23-4: 0xfffff, required
+# bit31-24: 0x0f, Size (i.e. 256MB)
+
+DATA 0xffd01508 0x10000000 # CS[1]n Base address to 256Mb
+DATA 0xffd0150c 0x00000000 # CS[1]n Size, window disabled
+
+DATA 0xffd01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xffd0151c 0x00000000 # CS[3]n Size, window disabled
+
+DATA 0xffd01494 0x00030000 # DDR ODT Control (Low)
+# bit3-0: ODT0Rd, MODT[0] asserted during read from DRAM CS1
+# bit7-4: ODT0Rd, MODT[0] asserted during read from DRAM CS0
+# bit19-16:2, ODT0Wr, MODT[0] asserted during write to DRAM CS1
+# bit23-20:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
+
+DATA 0xffd01498 0x00000000 # DDR ODT Control (High)
+# bit1-0: 0x0, ODT0 controlled by ODT Control (low) register above
+# bit3-2: 0x1, ODT1 active NEVER!
+# bit31-4: 0x0, required
+
+DATA 0xffd0149c 0x0000e803 # CPU ODT Control
+DATA 0xffd01480 0x00000001 # DDR Initialization Control
+# bit0: 0x1, enable DDR init upon this register write
+
+DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register
+DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/boards.cfg b/boards.cfg
index 3cf75c3..a33dfa2 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -153,6 +153,8 @@ openrd_client arm arm926ejs openrd Marvell
openrd_ultimate arm arm926ejs openrd Marvell kirkwood openrd:BOARD_IS_OPENRD_ULTIMATE
rd6281a arm arm926ejs - Marvell kirkwood
sheevaplug arm arm926ejs - Marvell kirkwood
+ib_nas6210 arm arm926ejs ib62x0 raidsonic kirkwood ib62x0:BOARD_IS_IB_NAS6210
+ib_nas6220 arm arm926ejs ib62x0 raidsonic kirkwood ib62x0:BOARD_IS_IB_NAS6220
dockstar arm arm926ejs - Seagate kirkwood
jadecpu arm arm926ejs jadecpu syteco mb86r0x
mx25pdk arm arm926ejs mx25pdk freescale mx25 mx25pdk:IMX_CONFIG=board/freescale/mx25pdk/imximage.cfg
diff --git a/include/configs/ib62x0.h b/include/configs/ib62x0.h
new file mode 100644
index 0000000..7373dca
--- /dev/null
+++ b/include/configs/ib62x0.h
@@ -0,0 +1,173 @@
+/*
+ * Copyright (C) 2011-2012
+ * Gerald Kerma <dreagle at doukki.net>
+ * Luka Perkov <uboot at lukaperkov.net>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef _CONFIG_IB62x0_H
+#define _CONFIG_IB62x0_H
+
+/*
+ * Version number information
+ */
+#if defined(CONFIG_BOARD_IS_IB_NAS6210)
+# define CONFIG_IDENT_STRING " RaidSonic ICY BOX IB-NAS6210"
+#elif defined(CONFIG_BOARD_IS_IB_NAS6220)
+# define CONFIG_IDENT_STRING " RaidSonic ICY BOX IB-NAS6220"
+#else
+# error Unknown RaidSonic ICY BOX board specified
+#endif
+
+/*
+ * High level configuration options
+ */
+#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD /* SOC Family Name */
+#define CONFIG_KW88F6281 /* SOC Name */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+
+/*
+ * Machine type
+ */
+#define CONFIG_MACH_TYPE MACH_TYPE_NAS6210
+
+/*
+ * Compression configuration
+ */
+#define CONFIG_BZIP2
+#define CONFIG_LZMA
+#define CONFIG_LZO
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH /* declare no flash (NOR/SPI) */
+#define CONFIG_SYS_MVFS
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+#undef CONFIG_SYS_PROMPT
+#if defined(CONFIG_BOARD_IS_IB_NAS6210)
+# define CONFIG_SYS_PROMPT "IB-NAS6210 => "
+#elif defined(CONFIG_BOARD_IS_IB_NAS6220)
+# define CONFIG_SYS_PROMPT "IB-NAS6220 => "
+#else
+# error Unknown RaidSonic ICY BOX board specified
+#endif
+
+/*
+ * Environment variables configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#else
+#define CONFIG_ENV_IS_NOWHERE
+#endif
+#define CONFIG_ENV_SIZE 0x20000
+#define CONFIG_ENV_OFFSET 0x80000
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND \
+ "setenv bootargs ${console} ${mtdparts} ${bootargs_root}; " \
+ "ubi part root; " \
+ "ubifsmount root; " \
+ "ubifsload 0x800000 ${kernel}; " \
+ "ubifsload 0x1100000 ${initrd}; " \
+ "bootm 0x800000 0x1100000"
+
+#define CONFIG_MTDPARTS \
+ "mtdparts=orion_nand:" \
+ "0x80000 at 0x0(uboot)," \
+ "0x20000 at 0x80000(uboot_env)," \
+ "- at 0xa0000(root)\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "console=console=ttyS0,115200\0" \
+ "mtdids=nand0=orion_nand\0" \
+ "mtdparts="CONFIG_MTDPARTS \
+ "kernel=/boot/uImage\0" \
+ "initrd=/boot/uInitrd\0" \
+ "bootargs_root=ubi.mtd=2 root=ubi0:root rootfstype=ubifs\0"
+
+/*
+ * Ethernet driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR 0
+#undef CONFIG_RESET_PHY_R
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * SATA driver configuration
+ */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_IDE_PREINIT
+#define CONFIG_DOS_PARTITION
+#define CONFIG_MVSATA_IDE_USE_PORT0
+# if defined(CONFIG_BOARD_IS_IB_NAS6210)
+# undef CONFIG_SYS_IDE_MAXBUS
+# define CONFIG_SYS_IDE_MAXBUS 1
+# undef CONFIG_SYS_IDE_MAXDEVICE
+# define CONFIG_SYS_IDE_MAXDEVICE 1
+# elif defined(CONFIG_BOARD_IS_IB_NAS6220)
+# define CONFIG_MVSATA_IDE_USE_PORT1
+# endif
+#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
+# if defined(CONFIG_BOARD_IS_IB_NAS6220)
+# define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
+# endif
+#endif /* CONFIG_CMD_IDE */
+
+/*
+ * RTC driver configuration
+ */
+#ifdef CONFIG_CMD_DATE
+#define CONFIG_RTC_MV
+#endif /* CONFIG_CMD_DATE */
+
+/*
+ * File system
+ */
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+
+#endif /* _CONFIG_IB62x0_H */
More information about the U-Boot
mailing list