[U-Boot] [PATCH v7] kirkwood: add NAS62x0 board support
Marek Vasut
marek.vasut at gmail.com
Sun Apr 15 12:41:10 CEST 2012
Dear Luka Perkov,
> Add support for new boards RaidSonic ICY BOX NAS6210 and NAS6220.
>
> NAS6210 has 1 SATA and 1 eSATA port while NAS6220 has 2 SATA ports.
>
> More information about the boards can be found here:
>
> http://www.raidsonic.de/en/products/nas-systems.php?we_objectID=7036
> http://www.raidsonic.de/en/products/nas-systems.php?we_objectID=7515
>
> Signed-off-by: Luka Perkov <uboot at lukaperkov.net>
> Signed-off-by: Gerald Kerma <dreagle at doukki.net>
> Signed-off-by: Simon Baatz <gmbnomis at gmail.com>
> ---
>
> Changes from version v1:
>
> * use tools/checkpatch.pl to locate patch errors and fix them
> * add two entries in boards.cfg, one for each board
> * fixed CONFIG_RESET_PHY_R
> * don't define values for macros that enable features only
> * remove static RAM configuration
> * fix comments
> * use only CONFIG_ENV_OFFSET and remove CONFIG_ENV_ADDR
> * clean coding style
> * add entry in MAINTAINERS file
>
> Changes from version v2:
>
> * use defined() in macros for board selection for robustness
>
> Changes from version v3:
>
> * don't use utf8 for Geralds name
> * don't mix upper/lower case in kwbimage.cfg
> * fix prompt
>
> Changes from version v4:
> * fix board Makefile (clean and distclean)
> * use generic way to handle arch number of the board
> * fix MAINTAINERS file
> * move code from Marvell to raidsonic folder
> * use CONFIG_MACH_TYPE
> * set only necessary GPIOs
> * use link instead of address for license
> * add few links about board being supported for quick reference
> * add previous change logs
> * multiple updates to kwbimage.cfg, thank you Simon
>
> Changes from version v5:
> * remove typo from kwbimage.cfg (duplicated lines), thank you David
> * clean up comments in kwbimage.cfg
>
> Changes from version v6:
> * replace KW_SATA_PORT0_OFFSET with MV_SATA_PORT0_OFFSET
> * change commit message
>
> NAS6210 eSATA port is not working from uboot... That is why there are
> CONFIG_BOARD_IS_IB_NAS6210 and CONFIG_BOARD_IS_IB_NAS6220 in ib62x0.h
> config file.
>
> Any chance to push this in 2012.04 release?
>
> MAINTAINERS | 5 +
> board/raidsonic/ib62x0/Makefile | 43 +++++++++
> board/raidsonic/ib62x0/ib62x0.c | 79 ++++++++++++++++
> board/raidsonic/ib62x0/ib62x0.h | 40 ++++++++
> board/raidsonic/ib62x0/kwbimage.cfg | 169
> ++++++++++++++++++++++++++++++++++ boards.cfg |
> 2 +
> include/configs/ib62x0.h | 173
> +++++++++++++++++++++++++++++++++++ 7 files changed, 511 insertions(+)
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 72f8b64..e6608ea 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -781,6 +781,11 @@ Linus Walleij <linus.walleij at linaro.org>
> integratorap various
> integratorcp various
>
> +Luka Perkov <uboot at lukaperkov.net>
> +
> + ib6210 ARM926EJS
> + ib6220 ARM926EJS
> +
> Dave Peverley <dpeverley at mpc-data.co.uk>
>
> omap730p2 ARM926EJS
> diff --git a/board/raidsonic/ib62x0/Makefile
> b/board/raidsonic/ib62x0/Makefile new file mode 100644
> index 0000000..d450f8d
> --- /dev/null
> +++ b/board/raidsonic/ib62x0/Makefile
> @@ -0,0 +1,43 @@
> +#
> +# (C) Copyright 2009
> +# Marvell Semiconductor <www.marvell.com>
> +# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
> +#
> +# See file CREDITS for list of people who contributed to this
> +# project.
> +#
> +# This program is free software; you can redistribute it and/or
> +# modify it under the terms of the GNU General Public License as
> +# published by the Free Software Foundation; either version 2 of
> +# the License, or (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program. If not, see <http://www.gnu.org/licenses/>.
> +#
> +
> +include $(TOPDIR)/config.mk
> +
> +LIB = $(obj)lib$(BOARD).o
> +
> +COBJS := ib62x0.o
> +
> +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
> +OBJS := $(addprefix $(obj),$(COBJS))
> +SOBJS := $(addprefix $(obj),$(SOBJS))
> +
> +$(LIB): $(obj).depend $(OBJS) $(SOBJS)
> + $(call cmd_link_o_target, $(OBJS) $(SOBJS))
> +
> +#########################################################################
> +
> +# defines $(obj).depend target
> +include $(SRCTREE)/rules.mk
> +
> +sinclude $(obj).depend
> +
> +#########################################################################
> diff --git a/board/raidsonic/ib62x0/ib62x0.c
> b/board/raidsonic/ib62x0/ib62x0.c new file mode 100644
> index 0000000..65f2c2e
> --- /dev/null
> +++ b/board/raidsonic/ib62x0/ib62x0.c
> @@ -0,0 +1,79 @@
> +/*
> + * Copyright (C) 2011-2012
> + * Gerald Kerma <dreagle at doukki.net>
> + * Luka Perkov <uboot at lukaperkov.net>
> + * Simon Baatz <gmbnomis at gmail.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> + */
> +
> +#include <common.h>
> +#include <miiphy.h>
> +#include <asm/arch/cpu.h>
> +#include <asm/arch/kirkwood.h>
> +#include <asm/arch/mpp.h>
> +#include "ib62x0.h"
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +int board_early_init_f(void)
> +{
> + /*
> + * default gpio configuration
> + * There are maximum 64 gpios controlled through 2 sets of registers
> + * the below configuration configures mainly initial LED status
> + */
> + kw_config_gpio(IB62x0_OE_VAL_LOW,
> + IB62x0_OE_VAL_HIGH,
> + IB62x0_OE_LOW, IB62x0_OE_HIGH);
> +
> + /* Multi-Purpose Pins Functionality configuration */
> + u32 kwmpp_config[] = {
> + MPP0_NF_IO2,
> + MPP1_NF_IO3,
> + MPP2_NF_IO4,
> + MPP3_NF_IO5,
> + MPP4_NF_IO6,
> + MPP5_NF_IO7,
> + MPP6_SYSRST_OUTn,
> + MPP8_TW_SDA,
> + MPP9_TW_SCK,
> + MPP10_UART0_TXD,
> + MPP11_UART0_RXD,
> + MPP18_NF_IO0,
> + MPP19_NF_IO1,
> + MPP20_SATA1_ACTn,
> + MPP21_SATA0_ACTn,
> + MPP22_GPIO, /* Power LED red */
> + MPP24_GPIO, /* Power off device */
> + MPP25_GPIO, /* Power LED green */
> + MPP27_GPIO, /* USB transfer LED */
> + MPP28_GPIO, /* Reset button */
> + MPP29_GPIO, /* USB Copy button */
> + 0
> + };
> + kirkwood_mpp_conf(kwmpp_config);
> + return 0;
> +}
> +
> +int board_init(void)
> +{
> + /* adress of boot parameters */
> + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
> +
> + return 0;
> +}
> diff --git a/board/raidsonic/ib62x0/ib62x0.h
> b/board/raidsonic/ib62x0/ib62x0.h new file mode 100644
> index 0000000..0c30690
> --- /dev/null
> +++ b/board/raidsonic/ib62x0/ib62x0.h
> @@ -0,0 +1,40 @@
> +/*
> + * Copyright (C) 2011-2012
> + * Gerald Kerma <dreagle at doukki.net>
> + * Simon Baatz <gmbnomis at gmail.com>
> + * Luka Perkov <uboot at lukaperkov.net>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> + */
> +
> +#ifndef __IB62x0_H
> +#define __IB62x0_H
> +
> +#define IB62x0_OE_LOW (~(1 << 22 | 1 << 24 | 1 << 25 | 1 <<
27))
> +#define IB62x0_OE_HIGH (~(0))
> +#define IB62x0_OE_VAL_LOW 0
> +#define IB62x0_OE_VAL_HIGH 0
> +
> +/* PHY related */
> +#define MV88E1116_LED_FCTRL_REG 10
> +#define MV88E1116_CPRSP_CR3_REG 21
> +#define MV88E1116_MAC_CTRL_REG 21
> +#define MV88E1116_PGADR_REG 22
> +#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
> +#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
> +
> +#endif /* __IB62x0_H */
> diff --git a/board/raidsonic/ib62x0/kwbimage.cfg
> b/board/raidsonic/ib62x0/kwbimage.cfg new file mode 100644
> index 0000000..bd594eb
> --- /dev/null
> +++ b/board/raidsonic/ib62x0/kwbimage.cfg
> @@ -0,0 +1,169 @@
> +#
> +# Copyright (C) 2011-2012
> +# Gerald Kerma <dreagle at doukki.net>
> +# Simon Baatz <gmbnomis at gmail.com>
> +# Luka Perkov <uboot at lukaperkov.net>
> +#
> +# See file CREDITS for list of people who contributed to this
> +# project.
> +#
> +# This program is free software; you can redistribute it and/or
> +# modify it under the terms of the GNU General Public License as
> +# published by the Free Software Foundation; either version 2 of
> +# the License, or (at your option) any later version.
> +#
> +# This program is distributed in the hope that it will be useful,
> +# but WITHOUT ANY WARRANTY; without even the implied warranty of
> +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> +# GNU General Public License for more details.
> +#
> +# You should have received a copy of the GNU General Public License
> +# along with this program. If not, see <http://www.gnu.org/licenses/>.
> +#
> +# Refer docs/README.kwimage for more details about how-to configure
> +# and create kirkwood boot image
> +#
> +
> +# Boot Media configurations
> +BOOT_FROM nand # change from nand to uart if building UART image
> +NAND_ECC_MODE default
> +NAND_PAGE_SIZE 0x0800
> +
> +# SOC registers configuration using bootrom header extension
> +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
> +
> +# Configure RGMII-0 interface pad voltage to 1.8V
> +DATA 0xffd100e0 0x1b1b1b9b
> +
> +#Dram initalization for SINGLE x16 CL=5 @ 400MHz
> +DATA 0xffd01400 0x43000c30 # DDR Configuration register
> +# bit13-0: 0xc30, (3120 DDR2 clks refresh rate)
> +# bit23-14: 0x0,
> +# bit24: 0x1, enable exit self refresh mode on DDR access
> +# bit25: 0x1, required
> +# bit29-26: 0x0,
> +# bit31-30: 0x1,
> +
> +DATA 0xffd01404 0x37543000 # DDR Controller Control Low
> +# bit4: 0x0, addr/cmd in smame cycle
> +# bit5: 0x0, clk is driven during self refresh, we don't care for APX
> +# bit6: 0x0, use recommended falling edge of clk for addr/cmd
> +# bit14: 0x0, input buffer always powered up
> +# bit18: 0x1, cpu lock transaction enabled
> +# bit23-20: 0x5, recommended value for CL=5 and STARTBURST_DEL disabled
> bit31=0 +# bit27-24: 0x7, CL+2, STARTBURST sample stages, for freqs
> 400MHz, unbuffered DIMM +# bit30-28: 0x3, required
> +# bit31: 0x0, no additional STARTBURST delay
> +
> +DATA 0xffd01408 0x22125451 # DDR Timing (Low) (active cycles value +1)
> +# bit3-0: TRAS lsbs
> +# bit7-4: TRCD
> +# bit11-8: TRP
> +# bit15-12: TWR
> +# bit19-16: TWTR
> +# bit20: TRAS msb
> +# bit23-21: 0x0
> +# bit27-24: TRRD
> +# bit31-28: TRTP
> +
> +DATA 0xffd0140c 0x00000a33 # DDR Timing (High)
> +# bit6-0: TRFC
> +# bit8-7: TR2R
> +# bit10-9: TR2W
> +# bit12-11: TW2W
> +# bit31-13: 0x0, required
> +
> +DATA 0xffd01410 0x0000000c # DDR Address Control
> +# bit1-0: 00, Cs0width (x8)
> +# bit3-2: 11, Cs0size (1Gb)
> +# bit5-4: 00, Cs1width (x8)
> +# bit7-6: 11, Cs1size (1Gb)
> +# bit9-8: 00, Cs2width (nonexistent
> +# bit11-10: 00, Cs2size (nonexistent
> +# bit13-12: 00, Cs3width (nonexistent
> +# bit15-14: 00, Cs3size (nonexistent
> +# bit16: 0, Cs0AddrSel
> +# bit17: 0, Cs1AddrSel
> +# bit18: 0, Cs2AddrSel
> +# bit19: 0, Cs3AddrSel
> +# bit31-20: 0x0, required
> +
> +DATA 0xffd01414 0x00000000 # DDR Open Pages Control
> +# bit0: 0, OpenPage enabled
> +# bit31-1: 0x0, required
> +
> +DATA 0xffd01418 0x00000000 # DDR Operation
> +# bit3-0: 0x0, DDR cmd
> +# bit31-4: 0x0, required
> +
> +DATA 0xffd0141c 0x00000c52 # DDR Mode
> +# bit2-0: 0x2, BurstLen=2 required
> +# bit3: 0x0, BurstType=0 required
> +# bit6-4: 0x4, CL=5
> +# bit7: 0x0, TestMode=0 normal
> +# bit8: 0x0, DLL reset=0 normal
> +# bit11-9: 0x6, auto-precharge write recovery ????????????
> +# bit12: 0x0, PD must be zero
> +# bit31-13: 0x0, required
> +
> +DATA 0xffd01420 0x00000040 # DDR Extended Mode
> +# bit0: 0, DDR DLL enabled
> +# bit1: 0, DDR drive strenght normal
> +# bit2: 1, DDR ODT control lsd (disabled)
> +# bit5-3: 0x0, required
> +# bit6: 0, DDR ODT control msb, (disabled)
> +# bit9-7: 0x0, required
> +# bit10: 0, differential DQS enabled
> +# bit11: 0, required
> +# bit12: 0, DDR output buffer enabled
> +# bit31-13: 0x0, required
> +
> +DATA 0xffd01424 0x0000f17f # DDR Controller Control High
> +# bit2-0: 0x7, required
> +# bit3: 0x1, MBUS Burst Chop disabled
> +# bit6-4: 0x7, required
> +# bit7: 0x0,
> +# bit8: 0x1, add writepath sample stage, must be 1 for DDR freq >=
> 300MHz +# bit9: 0x0, no half clock cycle addition to dataout
> +# bit10: 0x0, 1/4 clock cycle skew enabled for addr/ctl signals
> +# bit11: 0x0, 1/4 clock cycle skew disabled for write mesh
> +# bit15-12: 0xf, required
> +# bit31-16: 0, required
> +
> +DATA 0xffd01428 0x00085520 # DDR2 ODT Read Timing (default values)
> +DATA 0xffd0147c 0x00008552 # DDR2 ODT Write Timing (default values)
> +
> +DATA 0xffd01500 0x00000000 # CS[0]n Base address to 0x0
> +DATA 0xffd01504 0x0ffffff1 # CS[0]n Size
> +# bit0: 0x1, Window enabled
> +# bit1: 0x0, Write Protect disabled
> +# bit3-2: 0x0, CS0 hit selected
> +# bit23-4: 0xfffff, required
> +# bit31-24: 0x0f, Size (i.e. 256MB)
> +
> +DATA 0xffd01508 0x10000000 # CS[1]n Base address to 256Mb
> +DATA 0xffd0150c 0x00000000 # CS[1]n Size, window disabled
> +
> +DATA 0xffd01514 0x00000000 # CS[2]n Size, window disabled
> +DATA 0xffd0151c 0x00000000 # CS[3]n Size, window disabled
> +
> +DATA 0xffd01494 0x00030000 # DDR ODT Control (Low)
> +# bit3-0: ODT0Rd, MODT[0] asserted during read from DRAM CS1
> +# bit7-4: ODT0Rd, MODT[0] asserted during read from DRAM CS0
> +# bit19-16:2, ODT0Wr, MODT[0] asserted during write to DRAM CS1
> +# bit23-20:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0
> +
> +DATA 0xffd01498 0x00000000 # DDR ODT Control (High)
> +# bit1-0: 0x0, ODT0 controlled by ODT Control (low) register above
> +# bit3-2: 0x1, ODT1 active NEVER!
> +# bit31-4: 0x0, required
> +
> +DATA 0xffd0149c 0x0000e803 # CPU ODT Control
> +DATA 0xffd01480 0x00000001 # DDR Initialization Control
> +# bit0: 0x1, enable DDR init upon this register write
> +
> +DATA 0xFFD20134 0x66666666 # L2 RAM Timing 0 Register
> +DATA 0xFFD20138 0x66666666 # L2 RAM Timing 1 Register
> +
> +# End of Header extension
> +DATA 0x0 0x0
> diff --git a/boards.cfg b/boards.cfg
> index 3cf75c3..a33dfa2 100644
> --- a/boards.cfg
> +++ b/boards.cfg
> @@ -153,6 +153,8 @@ openrd_client arm arm926ejs
> openrd Marvell openrd_ultimate arm
> arm926ejs openrd Marvell kirkwood
> openrd:BOARD_IS_OPENRD_ULTIMATE rd6281a arm
> arm926ejs - Marvell kirkwood sheevaplug
> arm arm926ejs - Marvell
> kirkwood +ib_nas6210 arm arm926ejs ib62x0
> raidsonic kirkwood ib62x0:BOARD_IS_IB_NAS6210
> +ib_nas6220 arm arm926ejs ib62x0
> raidsonic kirkwood ib62x0:BOARD_IS_IB_NAS6220 dockstar
> arm arm926ejs - Seagate
> kirkwood jadecpu arm arm926ejs jadecpu
> syteco mb86r0x mx25pdk arm
> arm926ejs mx25pdk freescale
> mx25 mx25pdk:IMX_CONFIG=board/freescale/mx25pdk/imximage.cfg diff --
git
> a/include/configs/ib62x0.h b/include/configs/ib62x0.h
> new file mode 100644
> index 0000000..7373dca
> --- /dev/null
> +++ b/include/configs/ib62x0.h
> @@ -0,0 +1,173 @@
> +/*
> + * Copyright (C) 2011-2012
> + * Gerald Kerma <dreagle at doukki.net>
> + * Luka Perkov <uboot at lukaperkov.net>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> + */
> +
> +#ifndef _CONFIG_IB62x0_H
> +#define _CONFIG_IB62x0_H
> +
> +/*
> + * Version number information
> + */
> +#if defined(CONFIG_BOARD_IS_IB_NAS6210)
> +# define CONFIG_IDENT_STRING " RaidSonic ICY BOX IB-NAS6210"
> +#elif defined(CONFIG_BOARD_IS_IB_NAS6220)
> +# define CONFIG_IDENT_STRING " RaidSonic ICY BOX IB-NAS6220"
> +#else
> +# error Unknown RaidSonic ICY BOX board specified
> +#endif
> +
> +/*
> + * High level configuration options
> + */
> +#define CONFIG_FEROCEON_88FR131 /* CPU Core subversion */
> +#define CONFIG_KIRKWOOD /* SOC Family Name */
> +#define CONFIG_KW88F6281 /* SOC Name */
> +#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
> +
> +/*
> + * Machine type
> + */
> +#define CONFIG_MACH_TYPE MACH_TYPE_NAS6210
> +
> +/*
> + * Compression configuration
> + */
> +#define CONFIG_BZIP2
> +#define CONFIG_LZMA
> +#define CONFIG_LZO
> +
> +/*
> + * Commands configuration
> + */
> +#define CONFIG_SYS_NO_FLASH /* declare no flash (NOR/SPI) */
> +#define CONFIG_SYS_MVFS
> +#include <config_cmd_default.h>
> +#define CONFIG_CMD_ENV
> +#define CONFIG_CMD_IDE
> +#define CONFIG_CMD_MII
> +#define CONFIG_CMD_NAND
> +#define CONFIG_CMD_PING
> +#define CONFIG_CMD_USB
> +
> +/*
> + * mv-common.h should be defined after CMD configs since it used them
> + * to enable certain macros
> + */
> +#include "mv-common.h"
> +
> +#undef CONFIG_SYS_PROMPT
> +#if defined(CONFIG_BOARD_IS_IB_NAS6210)
> +# define CONFIG_SYS_PROMPT "IB-NAS6210 => "
> +#elif defined(CONFIG_BOARD_IS_IB_NAS6220)
> +# define CONFIG_SYS_PROMPT "IB-NAS6220 => "
> +#else
> +# error Unknown RaidSonic ICY BOX board specified
> +#endif
> +
> +/*
> + * Environment variables configuration
> + */
> +#ifdef CONFIG_CMD_NAND
> +#define CONFIG_ENV_IS_IN_NAND
> +#define CONFIG_ENV_SECT_SIZE 0x20000
> +#else
> +#define CONFIG_ENV_IS_NOWHERE
> +#endif
> +#define CONFIG_ENV_SIZE 0x20000
> +#define CONFIG_ENV_OFFSET 0x80000
The indent is weird in here?
> +
> +/*
> + * Default environment variables
> + */
> +#define CONFIG_BOOTCOMMAND \
> + "setenv bootargs ${console} ${mtdparts} ${bootargs_root}; " \
> + "ubi part root; " \
> + "ubifsmount root; " \
> + "ubifsload 0x800000 ${kernel}; " \
> + "ubifsload 0x1100000 ${initrd}; " \
> + "bootm 0x800000 0x1100000"
> +
> +#define CONFIG_MTDPARTS \
> + "mtdparts=orion_nand:" \
> + "0x80000 at 0x0(uboot)," \
> + "0x20000 at 0x80000(uboot_env)," \
> + "- at 0xa0000(root)\0"
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + "console=console=ttyS0,115200\0" \
> + "mtdids=nand0=orion_nand\0" \
> + "mtdparts="CONFIG_MTDPARTS \
> + "kernel=/boot/uImage\0" \
> + "initrd=/boot/uInitrd\0" \
> + "bootargs_root=ubi.mtd=2 root=ubi0:root rootfstype=ubifs\0"
> +
> +/*
> + * Ethernet driver configuration
> + */
> +#ifdef CONFIG_CMD_NET
> +#define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */
> +#define CONFIG_PHY_BASE_ADR 0
> +#undef CONFIG_RESET_PHY_R
> +#endif /* CONFIG_CMD_NET */
> +
> +/*
> + * SATA driver configuration
> + */
> +#ifdef CONFIG_CMD_IDE
> +#define __io
> +#define CONFIG_IDE_PREINIT
> +#define CONFIG_DOS_PARTITION
> +#define CONFIG_MVSATA_IDE_USE_PORT0
> +# if defined(CONFIG_BOARD_IS_IB_NAS6210)
> +# undef CONFIG_SYS_IDE_MAXBUS
> +# define CONFIG_SYS_IDE_MAXBUS 1
undef
define
Why ? Also, why do you use "# define" stuff (with these spaces)?
> +# undef CONFIG_SYS_IDE_MAXDEVICE
> +# define CONFIG_SYS_IDE_MAXDEVICE 1
> +# elif defined(CONFIG_BOARD_IS_IB_NAS6220)
> +# define CONFIG_MVSATA_IDE_USE_PORT1
> +# endif
> +#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
> +# if defined(CONFIG_BOARD_IS_IB_NAS6220)
> +# define CONFIG_SYS_ATA_IDE1_OFFSET MV_SATA_PORT1_OFFSET
> +# endif
> +#endif /* CONFIG_CMD_IDE */
> +
> +/*
> + * RTC driver configuration
> + */
> +#ifdef CONFIG_CMD_DATE
> +#define CONFIG_RTC_MV
> +#endif /* CONFIG_CMD_DATE */
> +
> +/*
> + * File system
> + */
> +#define CONFIG_CMD_EXT2
> +#define CONFIG_CMD_FAT
> +#define CONFIG_CMD_JFFS2
> +#define CONFIG_CMD_UBI
> +#define CONFIG_CMD_UBIFS
> +#define CONFIG_RBTREE
> +#define CONFIG_MTD_DEVICE
> +#define CONFIG_MTD_PARTITIONS
> +#define CONFIG_CMD_MTDPARTS
> +
> +#endif /* _CONFIG_IB62x0_H */
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
More information about the U-Boot
mailing list