[U-Boot] [PATCH 1/4 v2] serial: Add Zynq serial driver

Michal Simek monstr at monstr.eu
Thu Aug 16 08:30:27 CEST 2012


The driver is used on Xilinx Zynq platform.

Signed-off-by: Michal Simek <monstr at monstr.eu>

---
v2: Use Zynq name instead of Dragonfire and XPSS/XDFUART
    Rename driver name
    Remove driver description
---
 drivers/serial/Makefile      |    1 +
 drivers/serial/serial_zynq.c |  200 ++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 201 insertions(+), 0 deletions(-)
 create mode 100644 drivers/serial/serial_zynq.c

diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 65d0f23..dfc22a4 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -56,6 +56,7 @@ COBJS-$(CONFIG_S3C44B0_SERIAL) += serial_s3c44b0.o
 COBJS-$(CONFIG_XILINX_UARTLITE) += serial_xuartlite.o
 COBJS-$(CONFIG_SANDBOX_SERIAL) += sandbox.o
 COBJS-$(CONFIG_SCIF_CONSOLE) += serial_sh.o
+COBJS-$(CONFIG_ZYNQ_SERIAL) += serial_zynq.o
 
 ifndef CONFIG_SPL_BUILD
 COBJS-$(CONFIG_USB_TTY) += usbtty.o
diff --git a/drivers/serial/serial_zynq.c b/drivers/serial/serial_zynq.c
new file mode 100644
index 0000000..c49da3b
--- /dev/null
+++ b/drivers/serial/serial_zynq.c
@@ -0,0 +1,200 @@
+/*
+ * Copyright (C) 2012 Michal Simek <monstr at monstr.eu>
+ * Copyright (C) 2011-2012 Xilinx, Inc. All rights reserved.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <watchdog.h>
+#include <asm/io.h>
+#include <serial.h>
+
+#define ZYNQ_UART_SR_TXFULL	0x00000010 /* TX FIFO full */
+#define ZYNQ_UART_SR_RXEMPTY	0x00000002 /* RX FIFO empty */
+
+#define ZYNQ_UART_CR_TX_EN	0x00000010 /* TX enabled */
+#define ZYNQ_UART_CR_RX_EN	0x00000004 /* RX enabled */
+#define ZYNQ_UART_CR_TXRST	0x00000002 /* TX logic reset */
+#define ZYNQ_UART_CR_RXRST	0x00000001 /* RX logic reset */
+
+#define ZYNQ_UART_MR_PARITY_NONE	0x00000020  /* No parity mode */
+
+/* Some clock/baud constants */
+#define ZYNQ_UART_BDIV	15 /* Default/reset BDIV value */
+#define ZYNQ_UART_BASECLK	3125000L /* master / (bdiv + 1) */
+
+struct xdfuart {
+	u32 control; /* Control Register [8:0] */
+	u32 mode; /* Mode Register [10:0] */
+	u32 reserved1[4];
+	u32 baud_rate_gen; /* Baud Rate Generator [15:0] */
+	u32 reserved2[4];
+	u32 channel_sts; /* Channel Status [11:0] */
+	u32 tx_rx_fifo; /* FIFO [15:0] or [7:0] */
+	u32 baud_rate_divider; /* Baud Rate Divider [7:0] */
+};
+
+static struct xdfuart *xdf_ports[2] = {
+#ifdef CONFIG_ZYNQ_SERIAL_BASEADDR0
+	[0] = (struct xdfuart *)CONFIG_ZYNQ_SERIAL_BASEADDR0,
+#endif
+#ifdef CONFIG_ZYNQ_SERIAL_BASEADDR1
+	[1] = (struct xdfuart *)CONFIG_ZYNQ_SERIAL_BASEADDR1,
+#endif
+};
+
+struct xdfuart_params {
+	u32 baudrate;
+	u32 clock;
+};
+
+static struct xdfuart_params xdf_ports_param[2] = {
+#if defined(CONFIG_ZYNQ_SERIAL_BAUDRATE0) && defined(CONFIG_ZYNQ_SERIAL_CLOCK0)
+	[0].baudrate = CONFIG_ZYNQ_SERIAL_BAUDRATE0,
+	[0].clock = CONFIG_ZYNQ_SERIAL_CLOCK0,
+#endif
+#if defined(CONFIG_ZYNQ_SERIAL_BAUDRATE1) && defined(CONFIG_ZYNQ_SERIAL_CLOCK1)
+	[1].baudrate = CONFIG_ZYNQ_SERIAL_BAUDRATE1,
+	[1].clock = CONFIG_ZYNQ_SERIAL_CLOCK1,
+#endif
+};
+
+/* Set up the baud rate in gd struct */
+static void xdfuart_serial_setbrg(const int port)
+{
+	/* Calculation results. */
+	unsigned int calc_bauderror, bdiv, bgen;
+	unsigned long calc_baud = 0;
+	unsigned long baud = xdf_ports_param[port].baudrate;
+	unsigned long clock = xdf_ports_param[port].clock;
+	struct xdfuart *regs = xdf_ports[port];
+
+	/*                master clock
+	 * Baud rate = ------------------
+	 *              bgen * (bdiv + 1)
+	 *
+	 * Find acceptable values for baud generation.
+	 */
+	for (bdiv = 4; bdiv < 255; bdiv++) {
+		bgen = clock / (baud * (bdiv + 1));
+		if (bgen < 2 || bgen > 65535)
+			continue;
+
+		calc_baud = clock / (bgen * (bdiv + 1));
+
+		/*
+		 * Use first calculated baudrate with
+		 * an acceptable (<3%) error
+		 */
+		if (baud > calc_baud)
+			calc_bauderror = baud - calc_baud;
+		else
+			calc_bauderror = calc_baud - baud;
+		if (((calc_bauderror * 100) / baud) < 3)
+			break;
+	}
+
+	writel(bdiv, &regs->baud_rate_divider);
+	writel(bgen, &regs->baud_rate_gen);
+}
+
+/* Initialize the UART, with...some settings. */
+static int xdfuart_serial_init(const int port)
+{
+	struct xdfuart *regs = xdf_ports[port];
+
+	if (!regs)
+		return -1;
+
+	/* RX/TX enabled & reset */
+	writel(ZYNQ_UART_CR_TX_EN | ZYNQ_UART_CR_RX_EN | ZYNQ_UART_CR_TXRST | \
+					ZYNQ_UART_CR_RXRST, &regs->control);
+	writel(ZYNQ_UART_MR_PARITY_NONE, &regs->mode); /* 8 bit, no parity */
+	xdfuart_serial_setbrg(port);
+
+	return 0;
+}
+
+static void xdfuart_serial_putc(const char c, const int port)
+{
+	struct xdfuart *regs = xdf_ports[port];
+
+	while ((readl(&regs->channel_sts) & ZYNQ_UART_SR_TXFULL) != 0)
+		WATCHDOG_RESET();
+
+	if (c == '\n') {
+		writel('\r', &regs->tx_rx_fifo);
+		while ((readl(&regs->channel_sts) & ZYNQ_UART_SR_TXFULL) != 0)
+			WATCHDOG_RESET();
+	}
+	writel(c, &regs->tx_rx_fifo);
+}
+
+static void xdfuart_serial_puts(const char *s, const int port)
+{
+	while (*s)
+		xdfuart_serial_putc(*s++, port);
+}
+
+static int xdfuart_serial_tstc(const int port)
+{
+	struct xdfuart *regs = xdf_ports[port];
+
+	return (readl(&regs->channel_sts) & ZYNQ_UART_SR_RXEMPTY) == 0;
+}
+
+static int xdfuart_serial_getc(const int port)
+{
+	struct xdfuart *regs = xdf_ports[port];
+
+	while (!xdfuart_serial_tstc(port))
+		WATCHDOG_RESET();
+	return readl(&regs->tx_rx_fifo);
+}
+
+int serial_init(void)
+{
+	return xdfuart_serial_init(0);
+}
+
+void serial_setbrg(void)
+{
+	xdfuart_serial_setbrg(0);
+}
+
+void serial_putc(const char c)
+{
+	xdfuart_serial_putc(c, 0);
+}
+
+void serial_puts(const char *s)
+{
+	xdfuart_serial_puts(s, 0);
+}
+
+int serial_getc(void)
+{
+	return xdfuart_serial_getc(0);
+}
+
+int serial_tstc(void)
+{
+	return xdfuart_serial_tstc(0);
+}
-- 
1.7.0.4



More information about the U-Boot mailing list