[U-Boot] [PATCH] SMDK5250: Add ethernet support
Chander Kashyap
chander.kashyap at linaro.org
Thu Feb 9 12:15:41 CET 2012
Hi Simon,
On 24 January 2012 21:49, Simon Glass <sjg at chromium.org> wrote:
> Hi Chander,
>
> On Tue, Jan 24, 2012 at 5:03 AM, Chander Kashyap
> <chander.kashyap at linaro.org> wrote:
>> This patch enable support for SMC911X based ethernet device.
>>
>> Signed-off-by: Chander Kashyap <chander.kashyap at linaro.org>
>> ---
>> board/samsung/smdk5250/smdk5250.c | 89 +++++++++++++++++++++++++++++++++++++
>> include/configs/smdk5250.h | 13 +++++-
>> 2 files changed, 100 insertions(+), 2 deletions(-)
>>
>> diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c
>> index 2684620..a1b1a48 100644
>> --- a/board/samsung/smdk5250/smdk5250.c
>> +++ b/board/samsung/smdk5250/smdk5250.c
>> @@ -31,10 +31,95 @@
>> DECLARE_GLOBAL_DATA_PTR;
>> struct exynos5_gpio_part1 *gpio1;
>>
>> +static void smc9115_pre_init(void)
>
> Is there a common place where this function could go, so that other
> boards based on this SOC could use it also? Perhaps a
> board/samsun/exynos5 common directory?
As of now there is no common directory. Perhaps if more boards with
same gpio configuration are coming the n might be possible.
>
>> +{
>> + u32 smc_bw_conf, smc_bc_conf;
>> + int i;
>> +
>> + /*
>> + * SROM:CS1 and EBI
>> + *
>> + * GPY0[0] SROM_CSn[0]
>> + * GPY0[1] SROM_CSn[1](2)
>> + * GPY0[2] SROM_CSn[2]
>> + * GPY0[3] SROM_CSn[3]
>> + * GPY0[4] EBI_OEn(2)
>> + * GPY0[5] EBI_EEn(2)
>> + *
>> + * GPY1[0] EBI_BEn[0](2)
>> + * GPY1[1] EBI_BEn[1](2)
>> + * GPY1[2] SROM_WAIT(2)
>> + * GPY1[3] EBI_DATA_RDn(2)
>> + */
>> + s5p_gpio_cfg_pin(&gpio1->y0, CONFIG_ENV_SROM_BANK, GPIO_FUNC(2));
>> + s5p_gpio_cfg_pin(&gpio1->y0, 4, GPIO_FUNC(2));
>> + s5p_gpio_cfg_pin(&gpio1->y0, 5, GPIO_FUNC(2));
>> +
>> + for (i = 0; i < 4; i++)
>> + s5p_gpio_cfg_pin(&gpio1->y1, i, GPIO_FUNC(2));
>> +
>> + /*
>> + * EBI: 8 Addrss Lines
>> + *
>> + * GPY3[0] EBI_ADDR[0](2)
>> + * GPY3[1] EBI_ADDR[1](2)
>> + * GPY3[2] EBI_ADDR[2](2)
>> + * GPY3[3] EBI_ADDR[3](2)
>> + * GPY3[4] EBI_ADDR[4](2)
>> + * GPY3[5] EBI_ADDR{5](2)
>> + * GPY3[6] EBI_ADDR[6](2)
>> + * GPY3[7] EBI_ADDR{7](2)
>> + *
>> + * EBI: 16 Data Lines
>> + *
>> + * GPY5[0] EBI_DATA[0](2)
>> + * GPY5[1] EBI_DATA[1](2)
>> + * GPY5[2] EBI_DATA[2](2)
>> + * GPY5[3] EBI_DATA[3](2)
>> + * GPY5[4] EBI_DATA[4](2)
>> + * GPY5[5] EBI_DATA{5](2)
>> + * GPY5[6] EBI_DATA[6](2)
>> + * GPY5[7] EBI_DATA{7](2)
>> + *
>> + * GPY6[0] EBI_DATA[8](2)
>> + * GPY6[1] EBI_DATA[9](2)
>> + * GPY6[2] EBI_DATA[10](2)
>> + * GPY6[3] EBI_DATA110](2)
>> + * GPY6[4] EBI_DATA[12](2)
>> + * GPY6[5] EBI_DATA{13](2)
>> + * GPY6[6] EBI_DATA[14](2)
>> + * GPY6[7] EBI_DATA{15](2)
>> + */
>> + for (i = 0; i < 8; i++) {
>> + s5p_gpio_cfg_pin(&gpio1->y3, i, GPIO_FUNC(2));
>> + s5p_gpio_set_pull(&gpio1->y3, i, GPIO_PULL_UP);
>> +
>> + s5p_gpio_cfg_pin(&gpio1->y5, i, GPIO_FUNC(2));
>> + s5p_gpio_set_pull(&gpio1->y5, i, GPIO_PULL_UP);
>> +
>> + s5p_gpio_cfg_pin(&gpio1->y6, i, GPIO_FUNC(2));
>> + s5p_gpio_set_pull(&gpio1->y6, i, GPIO_PULL_UP);
>> + }
>> +
>> + /* Ethernet needs data bus width of 16 bits */
>> + smc_bw_conf = SROMC_DATA16_WIDTH(CONFIG_ENV_SROM_BANK)
>> + | SROMC_BYTE_ENABLE(CONFIG_ENV_SROM_BANK);
>> +
>> + smc_bc_conf = SROMC_BC_TACS(0x01) | SROMC_BC_TCOS(0x01)
>> + | SROMC_BC_TACC(0x06) | SROMC_BC_TCOH(0x01)
>> + | SROMC_BC_TAH(0x0C) | SROMC_BC_TACP(0x09)
>> + | SROMC_BC_PMC(0x01);
>> +
>> + /* Select and configure the SROMC bank */
>> + s5p_config_sromc(CONFIG_ENV_SROM_BANK, smc_bw_conf, smc_bc_conf);
>> +}
>> +
>> int board_init(void)
>> {
>> gpio1 = (struct exynos5_gpio_part1 *) samsung_get_base_gpio_part1();
>>
>> + smc9115_pre_init();
>
> Could this be done once later, in board_eth_init(), to avoid init of a
> device which might not be used?
Yes sure. I will move it before smc911x_initialize in board_eth_init().
>
>> +
>> gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
>> return 0;
>> }
>> @@ -79,6 +164,10 @@ void dram_init_banksize(void)
>> gd->bd->bi_dram[7].size = get_ram_size((long *)PHYS_SDRAM_8, \
>> PHYS_SDRAM_8_SIZE);
>> }
>> +int board_eth_init(bd_t *bis)
>> +{
>> + return smc911x_initialize(0, CONFIG_SMC911X_BASE);
>> +}
>>
>> #ifdef CONFIG_DISPLAY_BOARDINFO
>> int checkboard(void)
>> diff --git a/include/configs/smdk5250.h b/include/configs/smdk5250.h
>> index 6f2ef4c..4ad4bd2 100644
>> --- a/include/configs/smdk5250.h
>> +++ b/include/configs/smdk5250.h
>> @@ -98,8 +98,7 @@
>> #define CONFIG_CMD_MMC
>> #define CONFIG_CMD_EXT2
>> #define CONFIG_CMD_FAT
>> -#undef CONFIG_CMD_NET
>> -#undef CONFIG_CMD_NFS
>> +#define CONFIG_CMD_NET
>>
>> #define CONFIG_BOOTDELAY 3
>> #define CONFIG_ZERO_BOOTDELAY_CHECK
>> @@ -196,6 +195,16 @@
>> #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - 0x1000000)
>> #define MMC_MAX_CHANNEL 5
>>
>> +/* Ethernet Controllor Driver */
>> +#ifdef CONFIG_CMD_NET
>> +#define CONFIG_NET_MULTI
>> +#define CONFIG_SMC911X
>> +#define CONFIG_SMC911X_BASE 0x5000000
>> +#define CONFIG_SMC911X_16_BIT
>> +#define CONFIG_ENV_SROM_BANK 1
>> +#define CONFIG_ETHADDR "00:40:5c:26:0a:5b"
>
> This should come from the ethaddr environment variable I think.
Yes true. I will remove this.
>
>> +#endif /*CONFIG_CMD_NET*/
>> +
>> /* Enable devicetree support */
>> #define CONFIG_OF_LIBFDT
>>
>> --
>> 1.7.5.4
>>
>> _______________________________________________
>> U-Boot mailing list
>> U-Boot at lists.denx.de
>> http://lists.denx.de/mailman/listinfo/u-boot
>
> Regards,
> Simon
--
with warm regards,
Chander Kashyap
More information about the U-Boot
mailing list