[U-Boot] [PATCH v2 1/2] usb/ehci: Add USB support for the MX6Q
Marek Vasut
marek.vasut at gmail.com
Sat Feb 11 08:19:16 CET 2012
> > Currently, only USB Host 1 is supported.
>
> Hi,
>
> this resembles mx28 USBH ... or am I wrong? Can't these be coalesced
> together?
>
> btw Fabio, do we support mx6q USB host in mainline Linux ?
To make this even creepier ... the mx6q GPMI NAND interface is also taken from
mx28.
So basically, MX6q is MX28 with more (and v7) cores?
M
>
> > Cc: Remy Bohmer <linux at bohmer.net>
> > Signed-off-by: Wolfgang Grandegger <wg at denx.de>
> > ---
> >
> > arch/arm/cpu/armv7/mx6/clock.c | 13 ++
> > arch/arm/include/asm/arch-mx6/clock.h | 1 +
> > arch/arm/include/asm/arch-mx6/imx-regs.h | 3 +
> > drivers/usb/host/Makefile | 1 +
> > drivers/usb/host/ehci-mx6.c | 205
> >
> > ++++++++++++++++++++++++++++++ 5 files changed, 223 insertions(+), 0
> > deletions(-)
> >
> > create mode 100644 drivers/usb/host/ehci-mx6.c
> >
> > diff --git a/arch/arm/cpu/armv7/mx6/clock.c
> > b/arch/arm/cpu/armv7/mx6/clock.c index fa3a124..ef98563 100644
> > --- a/arch/arm/cpu/armv7/mx6/clock.c
> > +++ b/arch/arm/cpu/armv7/mx6/clock.c
> > @@ -36,6 +36,19 @@ enum pll_clocks {
> >
> > struct imx_ccm_reg *imx_ccm = (struct imx_ccm_reg *)CCM_BASE_ADDR;
> >
> > +void enable_usboh3_clk(unsigned char enable)
> > +{
> > + u32 reg;
> > +
> > + reg = __raw_readl(&imx_ccm->CCGR6);
> > + if (enable)
> > + reg |= MXC_CCM_CCGR_CG_MASK << MXC_CCM_CCGR0_CG0_OFFSET;
> > + else
> > + reg &= ~(MXC_CCM_CCGR_CG_MASK << MXC_CCM_CCGR0_CG0_OFFSET);
> > + __raw_writel(reg, &imx_ccm->CCGR6);
> > +
> > +}
> > +
> >
> > static u32 decode_pll(enum pll_clocks pll, u32 infreq)
> > {
> >
> > u32 div;
> >
> > diff --git a/arch/arm/include/asm/arch-mx6/clock.h
> > b/arch/arm/include/asm/arch-mx6/clock.h index 636458f..613809b 100644
> > --- a/arch/arm/include/asm/arch-mx6/clock.h
> > +++ b/arch/arm/include/asm/arch-mx6/clock.h
> > @@ -46,5 +46,6 @@ enum mxc_clock {
> >
> > u32 imx_get_uartclk(void);
> > u32 imx_get_fecclk(void);
> > unsigned int mxc_get_clock(enum mxc_clock clk);
> >
> > +void enable_usboh3_clk(unsigned char enable);
> >
> > #endif /* __ASM_ARCH_CLOCK_H */
> >
> > diff --git a/arch/arm/include/asm/arch-mx6/imx-regs.h
> > b/arch/arm/include/asm/arch-mx6/imx-regs.h index 3b5fd25..2bfe891 100644
> > --- a/arch/arm/include/asm/arch-mx6/imx-regs.h
> > +++ b/arch/arm/include/asm/arch-mx6/imx-regs.h
> > @@ -111,6 +111,9 @@
> >
> > #define KPP_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x38000)
> > #define WDOG1_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x3C000)
> > #define WDOG2_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x40000)
> >
> > +#define ANATOP_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x48000)
> > +#define USB_PHY0_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x49000)
> > +#define USB_PHY1_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x4a000)
> >
> > #define CCM_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x44000)
> > #define ANATOP_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x48000)
> > #define SNVS_BASE_ADDR (AIPS1_OFF_BASE_ADDR + 0x4C000)
> >
> > diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
> > index 77e217f..1b62cc2 100644
> > --- a/drivers/usb/host/Makefile
> > +++ b/drivers/usb/host/Makefile
> > @@ -43,6 +43,7 @@ endif
> >
> > COBJS-$(CONFIG_USB_EHCI_MXC) += ehci-mxc.o
> > COBJS-$(CONFIG_USB_EHCI_MXS) += ehci-mxs.o
> > COBJS-$(CONFIG_USB_EHCI_MX5) += ehci-mx5.o
> >
> > +COBJS-$(CONFIG_USB_EHCI_MX6) += ehci-mx6.o
> >
> > COBJS-$(CONFIG_USB_EHCI_PPC4XX) += ehci-ppc4xx.o
> > COBJS-$(CONFIG_USB_EHCI_IXP4XX) += ehci-ixp.o
> > COBJS-$(CONFIG_USB_EHCI_KIRKWOOD) += ehci-kirkwood.o
> >
> > diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c
> > new file mode 100644
> > index 0000000..b7bf49d
> > --- /dev/null
> > +++ b/drivers/usb/host/ehci-mx6.c
> > @@ -0,0 +1,205 @@
> > +/*
> > + * Copyright (c) 2009 Daniel Mack <daniel at caiaq.de>
> > + * Copyright (C) 2010 Freescale Semiconductor, Inc.
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > it + * under the terms of the GNU General Public License as published by
> > the + * Free Software Foundation; either version 2 of the License, or
> > (at your + * option) any later version.
> > + *
> > + * This program is distributed in the hope that it will be useful, but
> > + * WITHOUT ANY WARRANTY; without even the implied warranty of
> > MERCHANTABILITY + * or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
> > General Public License + * for more details.
> > + */
> > +
> > +#include <common.h>
> > +#include <usb.h>
> > +#include <errno.h>
> > +#include <linux/compiler.h>
> > +#include <usb/ehci-fsl.h>
> > +#include <asm/io.h>
> > +#include <asm/arch/imx-regs.h>
> > +#include <asm/arch/clock.h>
> > +#include <asm/arch/mx6x_pins.h>
> > +#include <asm/arch/iomux-v3.h>
> > +
> > +#include "ehci.h"
> > +#include "ehci-core.h"
> > +
> > +#define USB_OTGREGS_OFFSET 0x000
> > +#define USB_H1REGS_OFFSET 0x200
> > +#define USB_H2REGS_OFFSET 0x400
> > +#define USB_H3REGS_OFFSET 0x600
> > +#define USB_OTHERREGS_OFFSET 0x800
> > +
> > +#define USB_H1_CTRL_OFFSET 0x04
> > +
> > +#define USBPHY_CTRL 0x00000030
> > +#define USBPHY_CTRL_SET 0x00000034
> > +#define USBPHY_CTRL_CLR 0x00000038
> > +#define USBPHY_CTRL_TOG 0x0000003c
> > +
> > +#define USBPHY_PWD 0x00000000
> > +#define USBPHY_CTRL_SFTRST 0x80000000
> > +#define USBPHY_CTRL_CLKGATE 0x40000000
> > +#define USBPHY_CTRL_ENUTMILEVEL3 0x00008000
> > +#define USBPHY_CTRL_ENUTMILEVEL2 0x00004000
> > +
> > +#define ANADIG_USB2_CHRG_DETECT 0x00000210
> > +#define ANADIG_USB2_CHRG_DETECT_EN_B 0x00100000
> > +#define ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B 0x00080000
> > +
> > +#define ANADIG_USB2_PLL_480_CTRL 0x00000020
> > +#define ANADIG_USB2_PLL_480_CTRL_SET 0x00000024
> > +#define ANADIG_USB2_PLL_480_CTRL_CLR 0x00000028
> > +#define ANADIG_USB2_PLL_480_CTRL_BYPASS 0x00010000
> > +#define ANADIG_USB2_PLL_480_CTRL_ENABLE 0x00002000
> > +#define ANADIG_USB2_PLL_480_CTRL_POWER 0x00001000
> > +#define ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS 0x00000040
> > +
> > +
> > +#define UCTRL_OVER_CUR_POL (1 << 8) /* OTG Polarity of Overcurrent */
> > +#define UCTRL_OVER_CUR_DIS (1 << 7) /* Disable OTG Overcurrent Detection
> > */ +
> > +/* USBCMD */
> > +#define UH1_USBCMD_OFFSET 0x140
> > +#define UCMD_RUN_STOP (1 << 0) /* controller run/stop */
> > +#define UCMD_RESET (1 << 1) /* controller reset */
> > +
> > +static void usbh1_internal_phy_clock_gate(int on)
> > +{
> > + void __iomem *phy_reg = (void __iomem *)USB_PHY1_BASE_ADDR;
> > +
> > + phy_reg += on ? USBPHY_CTRL_CLR : USBPHY_CTRL_SET;
> > + __raw_writel(USBPHY_CTRL_CLKGATE, phy_reg);
> > +}
> > +
> > +static void usbh1_power_config(void)
> > +{
> > + void __iomem *anatop_base = (void __iomem *)ANATOP_BASE_ADDR;
> > +
> > + /*
> > + * Some phy and power's special controls for host1
> > + * 1. The external charger detector needs to be disabled
> > + * or the signal at DP will be poor
> > + * 2. The PLL's power and output to usb for host 1
> > + * is totally controlled by IC, so the Software only needs
> > + * to enable them at initializtion.
> > + */
> > + __raw_writel(ANADIG_USB2_CHRG_DETECT_EN_B |
> > + ANADIG_USB2_CHRG_DETECT_CHK_CHRG_B,
> > + anatop_base + ANADIG_USB2_CHRG_DETECT);
> > +
> > + __raw_writel(ANADIG_USB2_PLL_480_CTRL_BYPASS,
> > + anatop_base + ANADIG_USB2_PLL_480_CTRL_CLR);
> > +
> > + __raw_writel(ANADIG_USB2_PLL_480_CTRL_ENABLE |
> > + ANADIG_USB2_PLL_480_CTRL_POWER |
> > + ANADIG_USB2_PLL_480_CTRL_EN_USB_CLKS,
> > + anatop_base + ANADIG_USB2_PLL_480_CTRL_SET);
>
> This part looks mx28ish
>
> > +}
> > +
> > +static int usbh1_phy_enable(void)
> > +{
> > + void __iomem *phy_reg = (void __iomem *)USB_PHY1_BASE_ADDR;
> > + void __iomem *phy_ctrl = (void __iomem *)(phy_reg + USBPHY_CTRL);
> > + void __iomem *usb_cmd = (void __iomem *)(USBOH3_USB_BASE_ADDR +
> > + USB_H1REGS_OFFSET +
> > + UH1_USBCMD_OFFSET);
> > + u32 val;
> > +
> > + /* Stop then Reset */
> > + val = __raw_readl(usb_cmd);
> > + val &= ~UCMD_RUN_STOP;
> > + __raw_writel(val, usb_cmd);
> > + while (__raw_readl(usb_cmd) & UCMD_RUN_STOP)
> > + ;
> > +
> > + val = __raw_readl(usb_cmd);
> > + val |= UCMD_RESET;
> > + __raw_writel(val, usb_cmd);
> > + while (__raw_readl(usb_cmd) & UCMD_RESET)
> > + ;
> > +
> > + /* Reset USBPHY module */
> > + val = __raw_readl(phy_ctrl);
> > + val |= USBPHY_CTRL_SFTRST;
> > + __raw_writel(val, phy_ctrl);
> > + udelay(10);
>
> This part too.
>
> > +
> > + /* Remove CLKGATE and SFTRST */
> > + val = __raw_readl(phy_ctrl);
> > + val &= ~(USBPHY_CTRL_CLKGATE | USBPHY_CTRL_SFTRST);
> > + __raw_writel(val, phy_ctrl);
> > + udelay(10);
>
> This too, looks like mx28_reset_block(). But maybe I'm just paranoid and
> spooky here :)
>
> > +
> > + /* Power up the PHY */
> > + __raw_writel(0, phy_reg + USBPHY_PWD);
> > + /* enable FS/LS device */
> > + val = __raw_readl(phy_reg + USBPHY_CTRL);
> > + val |= (USBPHY_CTRL_ENUTMILEVEL2 | USBPHY_CTRL_ENUTMILEVEL3);
> > + __raw_writel(val, phy_reg + USBPHY_CTRL);
>
> And maybe not ... this looks like MX28 phy interface.
>
> M
>
> > +
> > + return 0;
> > +}
> > +
> > +static void usbh1_oc_config(void)
> > +{
> > + void __iomem *usb_base = (void __iomem *)USBOH3_USB_BASE_ADDR;
> > + void __iomem *usbother_base = usb_base + USB_OTHERREGS_OFFSET;
> > + u32 val;
> > +
> > + val = __raw_readl(usbother_base + USB_H1_CTRL_OFFSET);
> > +#if CONFIG_MACH_TYPE == MACH_TYPE_MX6Q_ARM2
> > + /* mx6qarm2 seems to required a different setting*/
> > + val &= ~UCTRL_OVER_CUR_POL;
> > +#else
> > + val |= UCTRL_OVER_CUR_POL;
> > +#endif
> > + __raw_writel(val, usbother_base + USB_H1_CTRL_OFFSET);
> > +
> > + val = __raw_readl(usbother_base + USB_H1_CTRL_OFFSET);
> > + val |= UCTRL_OVER_CUR_DIS;
> > + __raw_writel(val, usbother_base + USB_H1_CTRL_OFFSET);
> > +}
> > +
> > +int ehci_hcd_init(void)
> > +{
> > + struct usb_ehci *ehci;
> > +
> > + enable_usboh3_clk(1);
> > + mdelay(1);
> > +
> > + /* Do board specific initialization */
> > + board_ehci_hcd_init(CONFIG_MXC_USB_PORT);
> > +
> > +#if CONFIG_MXC_USB_PORT == 1
> > + /* USB Host 1 */
> > + usbh1_power_config();
> > + usbh1_oc_config();
> > + usbh1_internal_phy_clock_gate(1);
> > + usbh1_phy_enable();
> > +#else
> > +#error "MXC USB port not yet supported"
> > +#endif
> > +
> > + ehci = (struct usb_ehci *)(USBOH3_USB_BASE_ADDR +
> > + (0x200 * CONFIG_MXC_USB_PORT));
> > + hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
> > + hcor = (struct ehci_hcor *)((uint32_t)hccr +
> > + HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
> > + setbits_le32(&ehci->usbmode, CM_HOST);
> > +
> > + __raw_writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
> > + setbits_le32(&ehci->portsc, USB_EN);
> > +
> > + mdelay(10);
> > +
> > + return 0;
> > +}
> > +
> > +int ehci_hcd_stop(void)
> > +{
> > + return 0;
> > +}
More information about the U-Boot
mailing list