[U-Boot] [PATCH 4/4] SMDK5250: DDR3: Add memory initialization code for DDR3.
Hatim Ali
hatim.rv at samsung.com
Wed Feb 22 12:51:22 CET 2012
The patch adds memory initialization sequence for DDR3 @667Mhz
and enables DDR3 memory by default.
Signed-off-by: Hatim Ali <hatim.rv at samsung.com>
diff --git a/board/samsung/smdk5250/Makefile b/board/samsung/smdk5250/Makefile
index 3b4aa06..291fcc6 100644
--- a/board/samsung/smdk5250/Makefile
+++ b/board/samsung/smdk5250/Makefile
@@ -28,7 +28,13 @@ SOBJS := lowlevel_init.o
COBJS := clock_init.o
COBJS += dmc_common.o
+ifdef CONFIG_DDR3
+COBJS += dmc_init_ddr3.o
+else
+ifdef CONFIG_LPDDR2
COBJS += dmc_init_lpddr2.o
+endif
+endif
COBJS += tzpc_init.o
ifndef CONFIG_SPL_BUILD
diff --git a/board/samsung/smdk5250/dmc_init_ddr3.c b/board/samsung/smdk5250/dmc_init_ddr3.c
new file mode 100644
index 0000000..3e31043
--- /dev/null
+++ b/board/samsung/smdk5250/dmc_init_ddr3.c
@@ -0,0 +1,276 @@
+/*
+ * DDR3 mem setup file for SMDK5250 board based on EXYNOS5
+ *
+ * Copyright (C) 2012 Samsung Electronics
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <asm/io.h>
+#include <asm/arch/dmc.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/cpu.h>
+#include "setup.h"
+
+/* APLL : 1GHz */
+/* MCLK_CDREX: 667Mhz */
+/* Memory Type : DDR3 */
+
+static void reset_phy_ctrl(void)
+{
+ struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
+ writel(LPDDR3PHY_CTRL_PHY_RESET_OFF, &clk->lpddr3phy_ctrl);
+ sdelay(10000); /* approx 200us */
+ writel(LPDDR3PHY_CTRL_PHY_RESET, &clk->lpddr3phy_ctrl);
+}
+
+/* Sending ZQINIT command */
+static void config_zqinit(struct exynos5_dmc *dmc)
+{
+ unsigned long channel, chip, mask = 0, val;
+
+ for (channel = 0; channel < CONFIG_DMC_CHANNELS; channel++) {
+ SET_CMD_CHANNEL(mask, channel);
+ for (chip = 0; chip < CONFIG_CHIPS_PER_CHANNEL; chip++) {
+ SET_CMD_CHIP(mask, chip);
+ val = DIRECT_CMD_ZQINIT | mask;
+ writel(val, &dmc->directcmd);
+ }
+ }
+}
+
+static void config_ctrl_dll_on(unsigned int state,
+ struct exynos5_phy_control *phy0_ctrl,
+ struct exynos5_phy_control *phy1_ctrl)
+{
+ unsigned int val, tmp;
+ val = readl(&phy0_ctrl->phy_con13);
+ val &= (0x3F << 10);
+ val >>= 2;
+ tmp = PHY_CON12_RESET_VAL;
+ CONFIG_CTRL_DLL_ON(tmp, state);
+ val += tmp;
+ writel(val, &phy0_ctrl->phy_con12);
+
+ val = readl(&phy1_ctrl->phy_con13);
+ val &= (0x3F << 10);
+ val >>= 2;
+ tmp = PHY_CON12_RESET_VAL;
+ CONFIG_CTRL_DLL_ON(tmp, state);
+ val += tmp;
+ writel(val, &phy1_ctrl->phy_con12);
+}
+
+void mem_ctrl_init()
+{
+ struct exynos5_clock *clk = (struct exynos5_clock *)EXYNOS5_CLOCK_BASE;
+ struct exynos5_phy_control *phy0_ctrl, *phy1_ctrl;
+ struct exynos5_dmc *dmc;
+ unsigned int val;
+
+ phy0_ctrl = (struct exynos5_phy_control *)EXYNOS5_DMC_PHY0_BASE;
+ phy1_ctrl = (struct exynos5_phy_control *)EXYNOS5_DMC_PHY1_BASE;
+ dmc = (struct exynos5_dmc *)EXYNOS5_DMC_CTRL_BASE;
+
+ reset_phy_ctrl();
+
+ writel(0x0, &clk->src_cdrex);
+ writel(CLK_DIV_CDREX_VAL, &clk->div_cdrex);
+
+ writel(MPLL_CON1_VAL, &clk->mpll_con1);
+ writel(MPLL_CON0_VAL, &clk->mpll_con0);
+ writel(BPLL_CON1_VAL, &clk->bpll_con1);
+ writel(BPLL_CON0_VAL, &clk->bpll_con0);
+
+ writel(CLK_SRC_CDREX_VAL, &clk->src_cdrex);
+
+
+ /* Setting Operation Mode: DDR3
+ * Enabling byte_rdlvl
+ */
+ val = PHY_CON0_RESET_VAL;
+ SET_CTRL_DDR_MODE(val, DDR_MODE_DDR3);
+ val |= BYTE_RDLVL_EN;
+ writel(val, &phy0_ctrl->phy_con0);
+ writel(val, &phy1_ctrl->phy_con0);
+
+ /* Enable Read Leveling */
+ writel(SET_RDLVL_RDDATA_ADJ, &phy0_ctrl->phy_con1);
+ writel(SET_RDLVL_RDDATA_ADJ, &phy1_ctrl->phy_con1);
+
+ /* DQS, DQ: Signal, for LPDDR3: Always Set */
+ val = CTRL_PULLD_DQ | CTRL_PULLD_DQS;
+ writel(val, &phy0_ctrl->phy_con14);
+ writel(val, &phy1_ctrl->phy_con14);
+
+ /*set Read Latance and Burst Length for PHY0 and PHY1 */
+ writel(PHY_CON42_VAL, &phy0_ctrl->phy_con42);
+ writel(PHY_CON42_VAL, &phy1_ctrl->phy_con42);
+
+ /* ZQ Calibration */
+ config_zq(phy0_ctrl, phy1_ctrl);
+
+ /* Set DMC Concontrol
+ * dfi_init_start = 1
+ * rd_fetch = 0x3
+ * empty = 0
+ */
+ val = DMC_CONCONTROL_RESET_VAL;
+ SET_RD_FETCH(val);
+ val |= DFI_INIT_START;
+ val &= ~EMPTY;
+ writel(val, &dmc->concontrol);
+
+ /*
+ * Dynamic Clock: Always Running
+ * Memory Burst length: 8
+ * Number of chips: 1
+ * Memory Bus width: 32 bit
+ * Memory Type: DDR3
+ * Additional Latancy for PLL: 0 Cycle
+ */
+ writel(DMC_MEMCONTROL_VAL, &dmc->memcontrol);
+
+ config_memory(dmc);
+
+ /* Precharge Configuration */
+ writel(DMC_PRECHCONFIG_VAL, &dmc->prechconfig);
+
+ /* Power Down mode Configuration */
+ writel(DMC_PWRDNCONFIG_VAL, &dmc->pwrdnconfig);
+
+ /* Periodic Refresh Interval */
+ writel(DMC_TIMINGREF_VAL, &dmc->timingref);
+
+ /*
+ * TimingRow, TimingData, TimingPower Setting:
+ * Values as per Memory AC Parameters
+ */
+ writel(DMC_TIMINGROW_VAL, &dmc->timingrow);
+
+ writel(DMC_TIMINGDATA_VAL, &dmc->timingdata);
+
+ writel(DMC_TIMINGPOWER_VAL, &dmc->timingpower);
+
+ /* Memory Channel Inteleaving Size: 128 Bytes */
+ writel(CONFIG_IV_SIZE, &dmc->ivcontrol);
+
+ /* Set DQS offsets */
+ writel(DDR3_PHY0_DQS, &phy0_ctrl->phy_con4);
+ writel(DDR3_PHY1_DQS, &phy1_ctrl->phy_con4);
+
+ /* Set DQS offsets */
+ writel(DDR3_PHY0_DQ, &phy0_ctrl->phy_con6);
+ writel(DDR3_PHY1_DQ, &phy1_ctrl->phy_con6);
+
+ /* Set Debug offsets */
+ writel(RESET_DEBUG_OFFSET_VAL, &phy0_ctrl->phy_con10);
+ writel(RESET_DEBUG_OFFSET_VAL, &phy1_ctrl->phy_con10);
+
+ config_ctrl_dll_on(RESET, phy0_ctrl, phy1_ctrl);
+
+ sdelay(50); /* approx 10 PCLK cycle */
+
+ update_reset_dll(dmc);
+
+ config_mrs(dmc);
+ config_zqinit(dmc);
+
+ sdelay(50); /* approx 10 PCLK cycle */
+
+ /* Reset DLL Locking */
+ val = PHY_CON12_RESET_VAL;
+ CONFIG_CTRL_START(val, RESET);
+ writel(val, &phy0_ctrl->phy_con12);
+ writel(val, &phy1_ctrl->phy_con12);
+
+ /* Reset DLL Locking */
+ val = PHY_CON12_RESET_VAL;
+ CONFIG_CTRL_START(val, SET);
+ writel(val, &phy0_ctrl->phy_con12);
+ writel(val, &phy1_ctrl->phy_con12);
+
+ sdelay(50); /* approx 10 PCLK cycle */
+
+ do {
+ val = readl(&dmc->phystatus);
+ val &= (0x3 << 2);
+ } while (val == 0);
+
+ /* Set DMC Concontrol
+ * rd_fetch = 0x3
+ * empty = 0
+ * Basically here we are stopping dfi_init_start done above.
+ */
+ val = DMC_CONCONTROL_RESET_VAL;
+ SET_RD_FETCH(val);
+ val &= ~EMPTY;
+ writel(val, &dmc->concontrol);
+
+ update_reset_dll(dmc);
+
+ writel(SET_RDLVL_RDDATA_ADJ, &phy0_ctrl->phy_con1);
+ writel(SET_RDLVL_RDDATA_ADJ, &phy1_ctrl->phy_con1);
+
+ /* Enable Read Leveling */
+ val = PHY_CON2_RESET_VAL | RDLVL_EN;
+ writel(val, &phy0_ctrl->phy_con2);
+ writel(val, &phy1_ctrl->phy_con2);
+
+ /* Enable data eye training*/
+ val = RDLVL_CONFIG_RESET_VAL | CTRL_RDLVL_DATA_EN;
+ writel(val, &dmc->rdlvl_config);
+
+ do {
+ val = readl(&dmc->phystatus);
+ val &= (0x3<<14);
+ } while (val == 0);
+
+ /* Disable data eye training*/
+ val = RDLVL_CONFIG_RESET_VAL & ~CTRL_RDLVL_DATA_EN;
+ writel(val, &dmc->rdlvl_config);
+
+ config_ctrl_dll_on(SET, phy0_ctrl, phy1_ctrl);
+
+ update_reset_dll(dmc);
+
+ config_prech(dmc);
+
+ /*
+ * Dynamic Clock: Always Running
+ * Memory Burst length: 8
+ * Number of chips: 1
+ * Memory Bus width: 32 bit
+ * Memory Type: DDR3
+ * Additional Latancy for PLL: 0 Cycle
+ */
+ writel(DMC_MEMCONTROL_VAL, &dmc->memcontrol);
+
+ /* Set DMC Concontrol
+ * rd_fetch = 0x3
+ * empty = 0
+ * Auto refresh counter enable
+ */
+ val = DMC_CONCONTROL_RESET_VAL;
+ SET_RD_FETCH(val);
+ val &= ~EMPTY;
+ val |= AREF_EN;
+ writel(val, &dmc->concontrol);
+}
diff --git a/board/samsung/smdk5250/setup.h b/board/samsung/smdk5250/setup.h
index c061440..f51acab 100644
--- a/board/samsung/smdk5250/setup.h
+++ b/board/samsung/smdk5250/setup.h
@@ -1,5 +1,5 @@
/*
- * Machine Specific Values for SMDK5250 board based on S5PC520
+ * Machine Specific Values for SMDK5250 board based on Exynos5
*
* Copyright (C) 2012 Samsung Electronics
*
@@ -114,8 +114,13 @@
#define VPLL_CON1_VAL 0x00000000
#define VPLL_CON2_VAL 0x00000080
+#ifdef CONFIG_LPDDR2
#define BPLL_MDIV 0x215
#define BPLL_PDIV 0xC
+#elif defined CONFIG_DDR3
+#define BPLL_MDIV 0x185
+#define BPLL_PDIV 0x7
+#endif
#define BPLL_SDIV 0x1
#define BPLL_CON1_VAL 0x00203800
@@ -155,13 +160,19 @@
#define MCLK_CDREX_RATIO 0x0
#define ACLK_C2C_200_RATIO 0x1
#define C2C_CLK_400_RATIO 0x1
+#ifdef CONFIG_DDR3
+#define PCLK_CDREX_RATIO 0x4
+#else
#define PCLK_CDREX_RATIO 0x3
+#endif
#define ACLK_CDREX_RATIO 0x1
-#define CLK_DIV_CDREX_VAL ((MCLK_DPHY_RATIO << 20) \
- | (MCLK_CDREX_RATIO << 16) \
+#define CLK_DIV_CDREX_VAL ((MCLK_CDREX2_RATIO << 28) \
+ | (ACLK_EFCON_RATIO << 24) \
+ | (MCLK_DPHY_RATIO << 20) \
+ | (MCLK_CDREX_RATIO << 16) \
| (ACLK_C2C_200_RATIO << 12) \
- | (C2C_CLK_400_RATIO << 8) \
- | (PCLK_CDREX_RATIO << 4) \
+ | (C2C_CLK_400_RATIO << 8) \
+ | (PCLK_CDREX_RATIO << 4) \
| (ACLK_CDREX_RATIO))
#define MCLK_EFPHY_RATIO 0x4
@@ -360,8 +371,13 @@
/*ZQ Configurations */
#define PHY_CON16_RESET_VAL 0x08000304
+#ifdef CONFIG_LPDDR2
#define ZQ_MODE_DDS_VAL (0x5 << 24)
#define ZQ_MODE_TERM_VAL (0x5 << 21)
+#elif defined CONFIG_DDR3
+#define ZQ_MODE_DDS_VAL (0x7 << 24)
+#define ZQ_MODE_TERM_VAL (0x2 << 21)
+#endif
#define SET_ZQ_MODE_DDS_VAL(x) (x = (x & ~(0x7 << 24)) | ZQ_MODE_DDS_VAL)
#define SET_ZQ_MODE_TERM_VAL(x) (x = (x & ~(0x7 << 21)) | ZQ_MODE_TERM_VAL)
@@ -378,55 +394,181 @@
/* Diret Command */
#define DIRECT_CMD_NOP 0x07000000
+#define DIRECT_CMD_PALL 0x01000000
+#define DIRECT_CMD_ZQINIT 0x0A000000
+#ifdef CONFIG_LPDDR2
#define DIRECT_CMD_MRS1 0x00071C00
#define DIRECT_CMD_MRS2 0x00010BFC
#define DIRECT_CMD_MRS3 0x00000708
#define DIRECT_CMD_MRS4 0x00000818
-#define DIRECT_CMD_PALL 0x01000000
+#elif defined CONFIG_DDR3
+#define DIRECT_CMD_MRS1 0x00020010
+#define DIRECT_CMD_MRS2 0x00030000
+#define DIRECT_CMD_MRS3 0x00010042
+#define DIRECT_CMD_MRS4 0x00000B50
+#endif
-/* DLL Resync */
-#define FP_RSYNC (1 << 3)
+/* DMC PHY Control0 register */
+#define PHY_CONTROL0_RESET_VAL 0x0
+#define MEM_TERM_EN (1 << 31) /* Termination enable for memory */
+#define PHY_TERM_EN (1 << 30) /* Termination enable for PHY */
+#define CTRL_SHGATE (1 << 29) /* Duration of DQS gating signal */
+#define FP_RSYNC (1 << 3) /* Force DLL resyncronization */
+/* MDLL control */
+#define PHY_CON12_RESET_VAL 0x10100070
#define CONFIG_CTRL_DLL_ON(x, y) (x = (x & ~(1 << 5)) | y << 5)
#define CONFIG_CTRL_START(x, y) (x = (x & ~(1 << 6)) | y << 6)
#define SET_CTRL_FORCE_VAL(x, y) (x = (x & ~(0x7F << 8)) | y << 8)
-/* RDLVL */
-#define PHY_CON0_RESET_VAL 0x17023240
+/* PHY Control */
+#define PHY_CON0_RESET_VAL 0x17020A40
+#define DDR_MODE_DDR3 0x1
#define DDR_MODE_LPDDR2 0x2
+#define DDR_MODE_LPDDR3 0x3
#define BYTE_RDLVL_EN (1 << 13)
#define CTRL_ATGATE (1 << 6)
-#define SET_CTRL_DDR_MODE(x, y) (x = (x & ~(0x3 << 11)) | y << 11)
+#define SET_CTRL_DDR_MODE(x, y) (x = (x & ~(0x3 << 11)) | y << 11)
+#define SET_T_RDDATA_MARGIN(x, y) (x = (x & ~(0x7 << 17)) | y << 17)
#define PHY_CON1_RESET_VAL 0x9210100
+#ifdef CONFIG_DDR3
+#define RDLVL_RDDATA_ADJ 0xFF00
+#elif defined CONFIG_LPDDR2
#define RDLVL_RDDATA_ADJ 0x1
+#endif
#define SET_RDLVL_RDDATA_ADJ ((PHY_CON1_RESET_VAL & ~(0xFFFF << 0)) \
| RDLVL_RDDATA_ADJ << 0)
+#define DDR3_ADDR 0x0208
+
#define PHY_CON2_RESET_VAL 0x00010004
#define RDLVL_EN (1 << 25)
#define RDDSKEW_CLEAR (1 << 13)
+#define RDLVL_CONFIG_RESET_VAL 0x0
#define CTRL_RDLVL_DATA_EN (1 << 1)
#define LPDDR2_ADDR 0x00000208
-#define DMC_MEMCONFIG0_VAL 0x00001323
-#define DMC_MEMCONFIG1_VAL 0x00001323
-#define DMC_MEMBASECONFIG0_VAL 0x00400780
-#define DMC_MEMBASECONFIG1_VAL 0x00800780
-#define DMC_MEMCONTROL_VAL 0x00212500
+/* MEMCONTROL register bit fields */
+#define DMC_MEMCONTROL_CLK_STOP_DISABLE (0 << 0)
+#define DMC_MEMCONTROL_DPWRDN_DISABLE (0 << 1)
+#define DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE (0 << 2)
+#define DMC_MEMCONTROL_TP_DISABLE (0 << 4)
+#define DMC_MEMCONTROL_DSREF_DISABLE (0 << 5)
+#define DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(x) (x << 6)
+
+#define DMC_MEMCONTROL_MEM_TYPE_LPDDR3 (7 << 8)
+#define DMC_MEMCONTROL_MEM_TYPE_DDR3 (6 << 8)
+#define DMC_MEMCONTROL_MEM_TYPE_LPDDR2 (5 << 8)
+
+#define DMC_MEMCONTROL_MEM_WIDTH_32BIT (2 << 12)
+
+#define DMC_MEMCONTROL_NUM_CHIP_1 (0 << 16)
+#define DMC_MEMCONTROL_NUM_CHIP_2 (1 << 16)
+
+#define DMC_MEMCONTROL_BL_8 (3 << 20)
+#define DMC_MEMCONTROL_BL_4 (2 << 20)
+
+#define DMC_MEMCONTROL_PZQ_DISABLE (0 << 24)
+
+#define DMC_MEMCONTROL_MRR_BYTE_7_0 (0 << 25)
+#define DMC_MEMCONTROL_MRR_BYTE_15_8 (1 << 25)
+#define DMC_MEMCONTROL_MRR_BYTE_23_16 (2 << 25)
+#define DMC_MEMCONTROL_MRR_BYTE_31_24 (3 << 25)
+
+/* MEMCONFIG0 register bit fields */
+#define DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED (1 << 12)
+#define DMC_MEMCONFIGx_CHIP_COL_10 (3 << 8)
+#define DMC_MEMCONFIGx_CHIP_ROW_14 (2 << 4)
+#define DMC_MEMCONFIGx_CHIP_ROW_15 (3 << 4)
+#define DMC_MEMCONFIGx_CHIP_BANK_8 (3 << 0)
+
+
+#define DMC_MEMBASECONFIGx_CHIP_BASE(x) (x << 16)
+#define DMC_MEMBASECONFIGx_CHIP_MASK(x) (x << 0)
+#define DMC_MEMBASECONFIG_VAL(x) ( \
+ DMC_MEMBASECONFIGx_CHIP_BASE(x) | \
+ DMC_MEMBASECONFIGx_CHIP_MASK(0x780) \
+)
+
+#define DMC_MEMBASECONFIG0_VAL DMC_MEMBASECONFIG_VAL(0x40)
+#define DMC_MEMBASECONFIG1_VAL DMC_MEMBASECONFIG_VAL(0x80)
+
+#ifdef CONFIG_LPDDR2
+#define DMC_MEMCONTROL_VAL ( \
+ DMC_MEMCONTROL_CLK_STOP_DISABLE | \
+ DMC_MEMCONTROL_DPWRDN_DISABLE | \
+ DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE | \
+ DMC_MEMCONTROL_TP_DISABLE | \
+ DMC_MEMCONTROL_DSREF_DISABLE | \
+ DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) | \
+ DMC_MEMCONTROL_MEM_TYPE_LPDDR2 | \
+ DMC_MEMCONTROL_MEM_WIDTH_32BIT | \
+ DMC_MEMCONTROL_NUM_CHIP_2 | \
+ DMC_MEMCONTROL_BL_4 | \
+ DMC_MEMCONTROL_PZQ_DISABLE | \
+ DMC_MEMCONTROL_MRR_BYTE_7_0 \
+)
+#define DMC_MEMCONFIG_VAL ( \
+ DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED | DMC_MEMCONFIGx_CHIP_COL_10 | \
+ DMC_MEMCONFIGx_CHIP_ROW_14 | DMC_MEMCONFIGx_CHIP_BANK_8)
+#define DMC_MEMCONFIG1_VAL DMC_MEMCONFIG_VAL
+#define DMC_MEMCONFIG0_VAL DMC_MEMCONFIG_VAL
+
+#elif defined CONFIG_DDR3
+#define DMC_MEMCONTROL_VAL ( \
+ DMC_MEMCONTROL_CLK_STOP_DISABLE | \
+ DMC_MEMCONTROL_DPWRDN_DISABLE | \
+ DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE | \
+ DMC_MEMCONTROL_TP_DISABLE | \
+ DMC_MEMCONTROL_DSREF_DISABLE | \
+ DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) | \
+ DMC_MEMCONTROL_MEM_TYPE_DDR3 | \
+ DMC_MEMCONTROL_MEM_WIDTH_32BIT | \
+ DMC_MEMCONTROL_NUM_CHIP_1 | \
+ DMC_MEMCONTROL_BL_8 | \
+ DMC_MEMCONTROL_PZQ_DISABLE | \
+ DMC_MEMCONTROL_MRR_BYTE_7_0 \
+)
+#define DMC_MEMCONFIG_VAL ( \
+ DMC_MEMCONFIGx_CHIP_MAP_INTERLEAVED | DMC_MEMCONFIGx_CHIP_COL_10 | \
+ DMC_MEMCONFIGx_CHIP_ROW_15 | DMC_MEMCONFIGx_CHIP_BANK_8)
+#define DMC_MEMCONFIG1_VAL DMC_MEMCONFIG_VAL
+#define DMC_MEMCONFIG0_VAL DMC_MEMCONFIG_VAL
+#endif
+
#define DMC_PRECHCONFIG_VAL 0xFF000000
#define DMC_PWRDNCONFIG_VAL 0xFFFF00FF
+#ifdef CONFIG_LPDDR2
#define DMC_TIMINGREF_VAL 0x0000005D
#define DMC_TIMINGROW_VAL 0x2336544C
#define DMC_TIMINGDATA_VAL 0x24202408
#define DMC_TIMINGPOWER_VAL 0x38260235
+#elif defined CONFIG_DDR3
+#define DMC_TIMINGREF_VAL 0x000000BB
+#define DMC_TIMINGROW_VAL 0x7645644d
+#define DMC_TIMINGDATA_VAL 0x45414709
+#define DMC_TIMINGPOWER_VAL 0x3a000a3c
+#endif
+#ifdef CONFIG_LPDDR2
#define CTRL_BSTLEN 0x04
#define CTRL_RDLAT 0x08
+#elif defined CONFIG_DDR3
+#define CTRL_BSTLEN 0x08
+#define CTRL_RDLAT 0x09
+#endif
#define PHY_CON42_VAL (CTRL_BSTLEN << 8 | CTRL_RDLAT << 0)
/* DQS, DQ, DEBUG offsets */
+#ifdef CONFIG_DDR3
+#define DDR3_PHY0_DQS 0x08080808
+#define DDR3_PHY1_DQS 0x08080808
+#define DDR3_PHY0_DQ 0x08080808
+#define DDR3_PHY1_DQ 0x00080808
+#endif
+
#define SET_DQS_OFFSET_VAL 0x7F7F7F7F
#define SET_DQ_OFFSET_VAL 0x7F7F7F7F
#define SET_DEBUG_OFFSET_VAL 0x7F
@@ -438,13 +580,21 @@
#define CTRL_PULLD_DQ (0x0F << 8)
#define CTRL_PULLD_DQS (0x0F << 0)
+#define DMC_CONCONTROL_RESET_VAL 0x0FFF1100
+#ifdef CONFIG_LPDDR2
+#define RD_FETCH 0x3
+#elif defined CONFIG_DDR3
+#define RD_FETCH 0x2
+#endif
+#define SET_RD_FETCH(x) (x = (x & ~(0x7 << 12)) | RD_FETCH << 12)
#define DFI_INIT_START (1 << 28)
+#define EMPTY (1 << 8)
+#define AREF_EN (1 << 5)
#define CLK_STOP_EN (1 << 0)
#define DPWRDN_EN (1 << 1)
#define DSREF_EN (1 << 5)
-#define AREF_EN (1 << 5)
void sdelay(unsigned long);
void mem_ctrl_init(void);
void system_clock_init(void);
diff --git a/include/configs/smdk5250.h b/include/configs/smdk5250.h
index 9659f9e..cc24be6 100644
--- a/include/configs/smdk5250.h
+++ b/include/configs/smdk5250.h
@@ -37,6 +37,12 @@
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
+/* Choose DDR Type below:
+ * Uncomment the type of DDR present on your board
+ */
+#define CONFIG_DDR3
+/* #define CONFIG_LPDDR2 */
+
/* Keep L2 Cache Disabled */
#define CONFIG_SYS_DCACHE_OFF
--
1.7.2.3
More information about the U-Boot
mailing list