[U-Boot] [PATCH 2/2] kirkwood: Add support for the D-Link DNS-320
Jamie Lentin
jm at lentin.co.uk
Mon Jul 30 23:55:58 CEST 2012
Extend dnskw to support the D-Link DNS-320 ShareCenter NAS also. For more
information on this NAS, see:-
http://jamie.lentin.co.uk/devices/dlink-dns320
http://dns323.kood.org/dns-320
http://sharecenter.dlink.com/products/DNS-320
Signed-off-by: Jamie Lentin <jm at lentin.co.uk>
Cc: prafulla at marvell.com
Cc: albert.u.boot at aribaud.net
---
MAINTAINERS | 4 +
board/d-link/dnskw/dnskw.c | 8 +-
board/d-link/dnskw/dnskw.h | 6 +
board/d-link/dnskw/kwbimage.dns320.cfg | 207 ++++++++++++++++++++++++++++++++
boards.cfg | 1 +
include/configs/dnskw.h | 10 ++
6 files changed, 232 insertions(+), 4 deletions(-)
create mode 100644 board/d-link/dnskw/kwbimage.dns320.cfg
diff --git a/MAINTAINERS b/MAINTAINERS
index fd0c65c..92ede1f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -673,6 +673,10 @@ Igor Grinberg <grinberg at compulab.co.il>
cm-t35 ARM ARMV7 (OMAP3xx Soc)
+Jamie Lentin <jm at lentin.co.uk>
+
+ dns320 ARM926EJS (Kirkwood SoC)
+
Stefan Herbrechtsmeier <stefan at code.herbrechtsmeier.net>
dns325 ARM926EJS (Kirkwood SoC)
diff --git a/board/d-link/dnskw/dnskw.c b/board/d-link/dnskw/dnskw.c
index d29735c..cd6bfe9 100644
--- a/board/d-link/dnskw/dnskw.c
+++ b/board/d-link/dnskw/dnskw.c
@@ -58,8 +58,8 @@ int board_early_init_f(void)
MPP10_UART0_TXD,
MPP11_UART0_RXD,
MPP12_SD_CLK,
- MPP13_SD_CMD,
- MPP14_SD_D0,
+ MPP13_UART1_TXD, /* Custom ...*/
+ MPP14_UART1_RXD, /* ... controller */
MPP15_SD_D1,
MPP16_SD_D2,
MPP17_SD_D3,
@@ -74,13 +74,13 @@ int board_early_init_f(void)
MPP26_GPIO, /* power led */
MPP27_GPIO, /* sata0(right) error led */
MPP28_GPIO, /* sata1(left) error led */
- MPP29_GPIO, /* usb error led */
+ MPP29_GPIO, /* usb error led (dns-325) */
MPP30_GPIO,
MPP31_GPIO,
MPP32_GPIO,
MPP33_GPIO,
MPP34_GPIO, /* power key */
- MPP35_GPIO,
+ MPP35_GPIO, /* usb error led (dns-320) */
MPP36_GPIO,
MPP37_GPIO,
MPP38_GPIO,
diff --git a/board/d-link/dnskw/dnskw.h b/board/d-link/dnskw/dnskw.h
index 4b11cb6..8886050 100644
--- a/board/d-link/dnskw/dnskw.h
+++ b/board/d-link/dnskw/dnskw.h
@@ -43,6 +43,12 @@
#define DNSKW_OE_VAL_HIGH 0x00000800 /* disable leds */
#endif /* CONFIG_BOARD_IS_DNS325 */
+/* DNS-320 specific configuration */
+#ifdef CONFIG_BOARD_IS_DNS320
+#define DNSKW_OE_VAL_LOW 0x38000000 /* disable leds */
+#define DNSKW_OE_VAL_HIGH 0x00000808 /* disable leds */
+#endif /* CONFIG_BOARD_IS_DNS320 */
+
/* PHY related */
#define MV88E1116_MAC_CTRL_REG 21
#define MV88E1116_PGADR_REG 22
diff --git a/board/d-link/dnskw/kwbimage.dns320.cfg b/board/d-link/dnskw/kwbimage.dns320.cfg
new file mode 100644
index 0000000..5fb4052
--- /dev/null
+++ b/board/d-link/dnskw/kwbimage.dns320.cfg
@@ -0,0 +1,207 @@
+#
+# Copyright (C) 2012
+# Jamie Lentin <jm at lentin.co.uk>
+#
+# Based on dns325 support:
+# Copyright (C) 2011
+# Stefan Herbrechtsmeier <stefan at code.herbrechtsmeier.net>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM nand
+NAND_ECC_MODE default
+NAND_PAGE_SIZE 0x0800
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+
+# Configure RGMII-0 interface pad voltage to 1.8V
+DATA 0xFFD100e0 0x1b1b1b9b
+
+#Dram initalization for SINGLE x16 CL=3 @ 200MHz
+DATA 0xFFD01400 0x43000618 # DDR Configuration register
+# bit13-0: 0x618 DDR2 clks refresh rate
+# bit23-14: 0 required
+# bit24: 1 enable exit self refresh mode on DDR access
+# bit25: 1 required
+# bit29-26: 0 required
+# bit31-30: 0b01 required
+
+DATA 0xFFD01404 0x35143000 # DDR Controller Control Low
+# bit3-0: 0 required
+# bit4: 0, addr/cmd in smame cycle
+# bit5: 0, clk is driven during self refresh, we don't care for APX
+# bit6: 0, use recommended falling edge of clk for addr/cmd
+# bit11-7: 0 required
+# bit12: 1 required
+# bit13: 1 required
+# bit14: 0, input buffer always powered up
+# bit17-15: 0 required
+# bit18: 1, cpu lock transaction enabled
+# bit19: 0 required
+# bit23-20: 1, Recommended for CL 3 and STARTBURST_DEL disabled
+# bit27-24: 5, CL + 2
+# bit30-28: 3 required
+# bit31: 0, no additional STARTBURST delay
+
+DATA 0xFFD01408 0x11012227 # DDR Timing (Low)
+# bit3-0: 7, 8 cycle tRAS (tRAS[3-0])
+# bit7-4: 2, 3 cycle tRCD
+# bit11-8: 2, 3 cycle tRP
+# bit15-12: 2, 3 cycle tWR
+# bit19-16: 1, 2 cycle tWTR
+# bit20: 1, 2 cycle tRAS (tRAS[4])
+# bit23-21: 0 required
+# bit27-24: 1, 2 cycle tRRD
+# bit31-28: 1, 2 cycle tRTP
+
+DATA 0xFFD0140C 0x00000819 # DDR Timing (High)
+# bit6-0: 0x19, 20 cycle tRFC
+# bit8-7: 0, 1 cycle tR2bR
+# bit10-9: 0, 1 cycle tR2W
+# bit12-11: 1, 1 cycle tW2W gap
+# bit31-13: 0 required
+
+DATA 0xFFD01410 0x00000008 # DDR Address Control
+# bit1-0: 0, Cs0width=x8 (out of spec?)
+# bit3-2: 2, Cs0size=512Mb
+# bit5-4: 0, Cs1width=nonexistent
+# bit7-6: 0, Cs1size=nonexistent
+# bit9-8: 0, Cs2width=nonexistent
+# bit11-10: 0, Cs2size=nonexistent
+# bit13-12: 0, Cs3width=nonexistent
+# bit15-14: 0, Cs3size=nonexistent
+# bit16: 0, Cs0AddrSel
+# bit17: 0, Cs1AddrSel
+# bit18: 0, Cs2AddrSel
+# bit19: 0, Cs3AddrSel
+# bit31-20: 0 required
+
+DATA 0xFFD01414 0x00000000 # DDR Open Pages Control
+# bit0: 0, OPEn=OpenPage enabled
+# bit31-1: 0 required
+
+DATA 0xFFD01418 0x00000000 # DDR Operation
+# bit3-0: 0, Cmd=Normal SDRAM Mode
+# bit31-4: 0 required
+
+DATA 0xFFD0141C 0x00000632 # DDR Mode
+# bit2-0: 2, Burst Length (2 required)
+# bit3: 0, Burst Type (0 required)
+# bit6-4: 3, CAS Latency (CL) 3
+# bit7: 0, (Test Mode) Normal operation
+# bit8: 0, (Reset DLL) Normal operation
+# bit11-9: 3, Write recovery for auto-precharge (3 required)
+# bit12: 0, Fast Active power down exit time (0 required)
+# bit31-13: 0 required
+
+DATA 0xFFD01420 0x00000040 # DDR Extended Mode
+# bit0: 0, DRAM DLL enabled
+# bit1: 0, DRAM drive strength normal
+# bit2: 0, ODT control Rtt[0] (Rtt=2, 150 ohm termination)
+# bit5-3: 0 required
+# bit6: 1, ODT control Rtt[1] (Rtt=2, 150 ohm termination)
+# bit9-7: 0 required
+# bit10: 0, differential DQS enabled
+# bit11: 0 required
+# bit12: 0, DRAM output buffer enabled
+# bit31-13: 0 required
+
+DATA 0xFFD01424 0x0000F07F # DDR Controller Control High
+# bit2-0: 0x7 required
+# bit3: 1, MBUS Burst Chop disabled
+# bit6-4: 0x7 required
+# bit7: 0 required
+# bit8: 0, no add writepath sample stage
+# bit9: 0, no half clock cycle addition to dataout
+# bit10: 0, 1/4 clock cycle skew enabled for addr/ctl signals
+# bit11: 0, 1/4 clock cycle skew disabled for write mesh
+# bit15-12: 0xf required
+# bit31-16: 0 required
+
+DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing
+# bit3-0: 0 required
+# bit7-4: 2, 2 cycles from read command to assertion of M_ODT signal
+# bit11-8: 5, 5 cycles from read command to de-assertion of M_ODT signal
+# bit15-12: 5, 5 cycles from read command to assertion of internal ODT signal
+# bit19-16: 8, 8 cycles from read command to de-assertion of internal ODT signal
+# bit31-20: 0 required
+
+DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing
+# bit3-0: 2, 2 cycles from write comand to assertion of M_ODT signal
+# bit7-4: 5, 5 cycles from write command to de-assertion of M_ODT signal
+# bit15-12: 5, 5 cycles from write command to assertion of internal ODT signal
+# bit19-16: 8, 8 cycles from write command to de-assertion of internal ODT signal
+# bit31-16: 0 required
+
+DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0
+DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size
+# bit0: 1, Window enabled
+# bit1: 0, Write Protect disabled
+# bit3-2: 0x0, CS0 hit selected
+# bit23-4: 0xfffff required
+# bit31-24: 0x07, Size (i.e. 128MB)
+
+DATA 0xFFD01508 0x08000000 # CS[1]n Base address to 128Mb
+DATA 0xFFD0150C 0x0FFFFFF0 # CS[1]n Size, window disabled
+# bit0: 0, Window disabled
+# bit1: 0, Write Protect disabled
+# bit3-2: 0, CS1 hit selected
+# bit23-4: 0xfffff required
+# bit31-24: 0x0f, Size (i.e. 256MB)
+
+DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled
+DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled
+
+DATA 0xFFD01494 0x003c0000 # DDR ODT Control (Low)
+# bit3-0: 0b0000, (read) M_ODT[0] is not asserted during read from DRAM
+# bit7-4: 0b0000, (read) M_ODT[1] is not asserted during read from DRAM
+# bit15-8: 0 required
+# bit19-16: 0b1100, (write) M_ODT[0] is asserted during write to DRAM CS2 and CS3
+# bit23-20: 0b0011, (write) M_ODT[1] is asserted during write to DRAM CS0 and CS1
+# bit31-24: 0 required
+
+DATA 0xFFD01498 0x00000000 # DDR ODT Control (High)
+# bit1-0: 0, M_ODT[0] assertion is controlled by ODT Control Low register
+# bit3-2: 0, M_ODT[1] assertion is controlled by ODT Control Low register
+# bit31-4 0 required
+
+DATA 0xFFD0149C 0x0000E803 # CPU ODT Control
+# bit3-0: 0b0011, internal ODT is asserted during read from DRAM bank 0-1
+# bit7-4: 0b0000, internal ODT is not asserted during write to DRAM bank 0-4
+# bit9-8: 0, Internal ODT assertion is controlled by fiels
+# bit11-10: 2, M_DQ, M_DM, and M_DQS I/O buffer ODT 75 ohm
+# bit13-12: 2, M_STARTBURST_IN I/O buffer ODT 75 ohm
+# bit14: 1, M_STARTBURST_IN ODT enabled
+# bit15: 1, DDR IO ODT Unit: Drive ODT calibration values
+# bit20-16: 0, Pad N channel driving strength for ODT
+# bit25-21: 0, Pad P channel driving strength for ODT
+# bit31-26: 0 required
+
+DATA 0xFFD01480 0x00000001 # DDR Initialization Control
+# bit0: 1, enable DDR init upon this register write
+# bit31-1: 0, required
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/boards.cfg b/boards.cfg
index 8b8bb45..f0de201 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -139,6 +139,7 @@ hawkboard_uart arm arm926ejs da8xxevm davinci
enbw_cmc arm arm926ejs enbw_cmc enbw davinci
calimain arm arm926ejs calimain omicron davinci
pogo_e02 arm arm926ejs - cloudengines kirkwood
+dns320 arm arm926ejs dnskw d-link kirkwood dnskw:BOARD_IS_DNS320
dns325 arm arm926ejs dnskw d-link kirkwood dnskw:BOARD_IS_DNS325
lschlv2 arm arm926ejs lsxl buffalo kirkwood lsxl:LSCHLV2
lsxhl arm arm926ejs lsxl buffalo kirkwood lsxl:LSXHL
diff --git a/include/configs/dnskw.h b/include/configs/dnskw.h
index 2995d42..316f58a 100644
--- a/include/configs/dnskw.h
+++ b/include/configs/dnskw.h
@@ -41,6 +41,16 @@
#endif /* CONFIG_BOARD_IS_DNS325 */
+#ifdef CONFIG_BOARD_IS_DNS320
+#define MACH_TYPE_DNS320 3985
+#define CONFIG_MACH_TYPE MACH_TYPE_DNS320
+#define CONFIG_IDENT_STRING "\nD-Link DNS-320"
+
+#define CONFIG_SYS_KWD_CONFIG $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.dns320.cfg
+#define CONFIG_SYS_TCLK 166666667 /* 800Mhz */
+
+#endif /* CONFIG_BOARD_IS_DNS320 */
+
/*
* High Level Configuration Options (easy to change)
*/
--
1.7.10.4
More information about the U-Boot
mailing list