[U-Boot] [PATCH 02/20] arm/km: use correct kw_gpio function for NAND/SPI switching

Prafulla Wadaskar prafulla at marvell.com
Tue Jun 12 06:39:21 CEST 2012



> -----Original Message-----
> From: Valentin Longchamp [mailto:valentin.longchamp at keymile.com]
> Sent: 07 June 2012 15:37
> To: prafulla at mavell.com
> Cc: Valentin Longchamp; holger.brunck at keymile.com; u-
> boot at lists.denx.de; Gerlando Falauto; Prafulla Wadaskar
> Subject: [PATCH 02/20] arm/km: use correct kw_gpio function for
> NAND/SPI switching
> 
> This used to be done with registers direct access, which is not clear
> and optimal.
> 
> Signed-off-by: Valentin Longchamp <valentin.longchamp at keymile.com>
> Signed-off-by: Holger Brunck <holger.brunck at keymile.com>
> cc: Gerlando Falauto <gerlando.falauto at keymile.com>
> cc: Prafulla Wadaskar <prafulla at marvell.com>
> ---
>  board/keymile/km_arm/km_arm.c |   53 +++++++++++++++++++++-----------
> --------
>  include/configs/km/km_arm.h   |    1 +
>  2 files changed, 29 insertions(+), 25 deletions(-)
> 
> diff --git a/board/keymile/km_arm/km_arm.c
> b/board/keymile/km_arm/km_arm.c
> index ed12b5c..e4ae1fb 100644
> --- a/board/keymile/km_arm/km_arm.c
> +++ b/board/keymile/km_arm/km_arm.c
> @@ -247,15 +247,12 @@ int board_early_init_f(void)
>  	kirkwood_mpp_conf(kwmpp_config, NULL);
> 
>  	/*
> -	 * The FLASH_GPIO_PIN switches between using a
> +	 * The KM_FLASH_GPIO_PIN switches between using a
>  	 * NAND or a SPI FLASH. Set this pin on start
>  	 * to NAND mode.
>  	 */
> -	tmp = readl(KW_GPIO0_BASE);
> -	writel(tmp | FLASH_GPIO_PIN , KW_GPIO0_BASE);
> -	tmp = readl(KW_GPIO0_BASE + 4);
> -	writel(tmp & (~FLASH_GPIO_PIN) , KW_GPIO0_BASE + 4);
> -
> +	kw_gpio_set_valid(KM_FLASH_GPIO_PIN, 1);
> +	kw_gpio_direction_output(KM_FLASH_GPIO_PIN, 1);
>  #if defined(CONFIG_SOFT_I2C)
>  	/* init the GPIO for I2C Bitbang driver */
>  	kw_gpio_set_valid(KM_KIRKWOOD_SDA_PIN, 1);
> @@ -284,35 +281,41 @@ int board_init(void)
>  	return 0;
>  }
> 
> +int km_hw_spi_bus_claim(int on)
> +{
> +	int gpio_value = !on;
> +
> +	if (on) {
> +		kwmpp_config[0] = MPP0_SPI_SCn;
> +		kwmpp_config[1] = MPP1_SPI_MOSI;
> +		kwmpp_config[2] = MPP2_SPI_SCK;
> +		kwmpp_config[3] = MPP3_SPI_MISO;
> +	} else {
> +		kwmpp_config[0] = MPP0_NF_IO2;
> +		kwmpp_config[1] = MPP1_NF_IO3;
> +		kwmpp_config[2] = MPP2_NF_IO4;
> +		kwmpp_config[3] = MPP3_NF_IO5;
> +	}

NACK...

Regards..
Prafulla . . .


More information about the U-Boot mailing list